Search NASA⌕ Search

SEARCH · Search NASA

Results for “Embrittlement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Irradiation effects in tungsten—From surface effects to bulk mechanical properties

Advanced materials such as tungsten fibre-reinforced composites allow to overcome severe weaknesses of the baseline materials for plasma-facing components — copper and tungsten. The effect of the fusion environment on the mechanical properties of these materials, e.g. the embrittlement by neutron irradiation, plays a key role for the development of future fusion reactors. To simulate this effect, high-energy ions are used as a substitute for the displacement damage by neutrons. We propose the use of very fine tungsten wire as a possibility of studying the influence of irradiation damage on the mechanical properties. This is possible as they allow full-depth irradiation of almost the entire volume despite the limited penetration depth of ions. Geometrical size effects are mitigated due to the nanoscale microstructure of the wire. In addition, similar wire is used in tungsten fibre-reinforced composites. Thus, the investigation of irradiated wire can directly be used for the prediction of the bulk composite properties. For the proof of this concept tungsten wire with a diameter of 16 μm was electrochemically thinned to 5 μm and irradiated with 20.5 MeV W 6+ ions. The mechanical properties were subsequently determined by macroscopic tensile testing. Irradiation to 0.3, 1 and 9 dpa did not lead to a change of the mechanical behaviour. Both strength and ductility, the latter indicated by the reduction of area, were similar to the as-fabricated state.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A critical review of irradiation-induced changes in reactor pressure vessel steels

A large body of work has been conducted to investigate the embrittlement and degradation of reactor pressure vessel (RPV) steels. This includes experiments on alloys with different compositions, performed in research and test reactors and ion accelerators that span various temperatures, fluxes, and fluences. In this paper, we perform a critical review of the published experimental data and compile experimentally reported values for dislocation loop size/density, precipitate size/density and yield stress into an easily downloadable format that can be used by both experimentalists and modelers. This thorough experimental review is complemented by a brief review of simulation efforts at atomistic and mesoscopic length scales. Finally, this paper highlights key aspects of the behavior of RPV steels under irradiation, identifies gaps or discrepancies in current understanding, and identifies priority future research directions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Comments on “Failure analysis of corroded hydrogen-blended natural gas pipelines based on finite element analysis and genetic algorithm-back propagation neural network” [262 (2025) 111174]

This is a brief commentary paper to highlight and discuss the determination of hydrogen concentration in pipeline steel, effect of hydrogen embrittlement (HE) on the mechanical properties of the material, burst strength of corroded pipelines using finite element analysis (FEA) simulations, and curve-fit models for assessing remaining strength of X80 corroded pipelines for transporting hydrogen blended natural gas. Recently, Xie et al. [1] proposed a methodology to quantify the impact of HE on material properties and numerically determined burst pressure of X80 corroded pipelines. However, their HE quantification overestimated the degradation of tensile strength for hydrogen blending ratios beyond the original data range, and their FEA results of burst pressure are nonconservative. This work thus recharacterized the hydrogen concentration in the steel pipeline and the effect of HE on tensile strength, and then redetermined burst pressures for a set of typical corrosion defect cases considered by Xie et al. [1] based on an experimentally validated FEA modelling method. With the new FEA results, two empirical corrosion models were proposed for X80 corroded pipelines for hydrogen service. At zero hydrogen blending ratio, the novel empirical models predict burst pressures to be consistent with the industry-accepted corrosion models. Furthermore, both the numerical simulation method and the novel corrosion models are significant contributions to the pipeline industry and the hydrogen community. Application of these results will enhance the safety, reliability, and integrity of natural gas pipelines when used to transport hydrogen.

Burst pressure prediction↗
DOE OSTI2025

Rapid tempering to enhance dynamic performance of high and ultra-high strength steels

This study employed rapid, short-time duration (1 s) tempering to improve the dynamic performance of high-strength steel (HSS) and ultra-high-strength steel (UHSS), compared to quenched and conventionally (1800 s) tempered microstructures. Rapid tempering significantly improved the Charpy toughness of both steels compared to the conventionally tempered condition at an equivalent tempering parameter (TP) or hardness level. For conventionally tempered conditions, tempered martensite embrittlement was observed within the tempering temperature range of 200–400 °C, whereas rapid tempering exhibited increased Charpy toughness with increasing tempering temperature across all tempering conditions. Dynamic compression experiments indicated that rapid tempering led to improved ductility compared to the conventionally tempered condition at an equivalent TP. This work shows that the same rapid tempering strategy used for HSS is directly transferable to a higher-carbon UHSS and provides the first systematic evidence of improved strength-ductility combinations and cracking resistance under dynamic compression, supported by Kolsky bar experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A reactive molecular dynamics model for uranium/hydrogen containing systems

Uranium-based materials are valuable assets in the energy, medical, and military industries. However, understanding their sensitivity to hydrogen embrittlement is particularly challenging due to the toxicity of uranium and the computationally expensive nature of quantum-based methods generally required to study such processes. In this regard, we have developed a Chebyshev Interaction Model for Efficient Simulation (ChIMES) that can be employed to compute energies and forces of U and UH3 bulk structures with vacancies and hydrogen interstitials with accuracy similar to that of Density Functional Theory (DFT) while yielding linear scaling and orders of magnitude improvement in computational efficiency. Here, we show that the bulk structural parameters, uranium and hydrogen vacancy formation energies, and diffusion barriers predicted by the ChIMES potential are in strong agreement with the reference DFT data. We then use ChIMES to conduct molecular dynamics simulations of the temperature-dependent diffusion of a hydrogen interstitial and determine the corresponding diffusion activation energy. Our model has particular significance in studies of actinides and other high-Z materials, where there is a strong need for computationally efficient methods to bridge length and time scales between experiments and quantum theory.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Molecular dynamics study of hydrogen Cottrell atmosphere in aluminum: Influence of solute-solute interactions in the dislocation core

Cottrell atmospheres form when solute atoms segregate to dislocations, and is one of the most basic processes by which solutes alter mechanical properties of materials. In the case of hydrogen, Cottrell atmospheres are believed to contribute to hydrogen embrittlement. Here, in this study, we use direct molecular dynamics simulations to study the formation of hydrogen Cottrell atmospheres around edge dislocations in aluminum. Using coarse-graining techniques, we resolve the temporal and spatial evolution of the hydrogen concentration field. By comparing our results with theories of Cottrell atmosphere formation and thermodynamics, we show that a repulsive, concentration-dependent H-H interaction reduces the peak atmosphere concentration at the dislocation core. Furthermore, this interaction differs significantly from the H-H interaction that is experienced in the bulk away from a dislocation.

Aluminum↗
DOE OSTI2021

2020 Report - SRNL Aging and Lifetimes program tritium aging studies on structural alloys

This report documents work performed in calendar year 2020 at SRNL in support of the Aging and Lifetimes program. This work is part of an on-going collaboration between SRNL and SNL to understand tritium embrittlement of structural metals in Gas Transfer System reservoirs which informs lifetime assessments and lifetime predictions. In this effort, test coupons are precharged with tritium and allowed to age in a freezer to minimize tritium egress and allow for born-in helium levels to systematically increase. Coupons are then removed periodically and tested to develop an understanding of how mechanical properties degrade as helium levels increase. This report summarizes test results from coupons which are in various stages of aging as they were tritium precharged in previous years.

36 MATERIALS SCIENCE↗
DOE OSTI2022

2021 Report - SRNL Aging and Lifetimes program tritium aging studies on structural alloys

This report documents work performed in fiscal year 2021 at SRNL in support of the Aging and Lifetimes program. This work is part of an on-going collaboration between SRNL and SNL to understand tritium embrittlement of structural metals used in Gas Transfer System reservoirs, thereby informing lifetime assessments and predictions. In this effort, test coupons are pre-charged with tritium and allowed to age in a freezer to minimize tritium diffusion and off-gassing while allowing for born-in helium levels to systematically increase. Coupons are then removed periodically and tested to develop an understanding of how mechanical properties degrade as helium levels increase. This report summarizes test results from coupons which are in various stages of aging as they were tritium pre-charged in previous years. Tests were performed on 304L that was previously tritium pre-charged and allowed to age to nominally 300 appm helium. Specimens from this study were previously tested at 100 appm nominal helium content, and this new test point expands that study. Tensile testing of these heat treated 304L tubes (and welded tubes) aged to 100 appm helium were completed which provided a unique study of a diverse set of microstructures and yield strengths ranging from 200-800 MPa. Additionally, 304L notched and smooth tensile specimens aged to 300 appm helium were tensile tested to predetermined strains to provide for a systematic microscopy investigation of aging effects on microstructural damage in partnership with SNL. Testing was performed on 304L electron beam (EB) weld coupons as well as 21-6-9 annealed coupons that were thermally pre-charged in 2020. Tests on the EB welds were completed at 100 appm helium contents, and tests on the annealed 21-6-9 material were completed at 100, 200, and 300 appm helium. Table 0-1 provides the status of the ongoing tritium coupon aging studies. The table includes the year tritium pre-charging took place, the material, and the targeted helium concentrations (appm) for testing.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

2022 Report - SRNL Aging and Lifetimes program tritium aging studies on structural alloys

This report documents work performed in fiscal year 2022 at SRNL in support of the Aging and Lifetimes program. This work is an enduring collaboration between SRNL and SNL to study tritium embrittlement of structural metals used in Gas Transfer System reservoirs. The measured data inform component lifetime assessments and predictions. Test coupons are thermally pre-charged with tritium and allowed to age at cryogenic temperatures to freeze out tritium diffusion and minimize off-gassing while allowing for decay helium levels to build. Coupons are removed and tested at planned intervals to measure how mechanical properties degrade as helium levels increase. This report summarizes test results from coupons which are in various stages of aging as they were tritium pre-charged in previous years, as well as documenting one new charging run.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

A Model to Account for the Effects of Load Ratio and Hydrogen Pressure on the Fatigue Crack Growth Behavior of Pressure Vessel Steels

A phenomenological model for estimating the effects of load ratio R and hydrogen pressure P H2 on the hydrogen-assisted fatigue crack growth rate (HA–FCGR) behavior in the transient and steady-state regimes of pressure vessel steels is described. The “transient regime” is identified with crack growth within a severely embrittled zone of intense plasticity at the crack tip. The “steady-state” behavior is associated with the crack growing into a region of comparatively lower hydrogen concentration located further away from the crack tip. The model treats the effects of R and P H2 as being functionally separable. In the transient regime, the effects of the hydrogen pressure on the HA–FCGR behavior were negligible but were significant in the steady-state regime. The hydrogen concentration in the steady-state region is modeled as being dependent on the kinetics of lattice diffusion, which is sensitive to pressure. Experimental HA–FCGR data from the literature were used to validate the model. The new model was shown to be valid over a wide range of conditions that ranged between –1 ≤ R ≤ 0.8 and 0.02 ≤ P H2 ≤ 103 MPa for pressure vessel steels.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructural Engineering of Mn-Alloyed Austenitic Steel for Hydrogen Storage and Delivery

Austenitic stainless steels are commonly used for hydrogen storage and transportation. These alloys have a high nickel (Ni) content, which increases alloy cost. In this study, high manganese (Mn) austenitic alloys were evaluated as potential lower cost alternatives. Two heats of high Mn alloys with different stacking fault energies (SFE) of ~29 mJ·m -2 and 49 mJ·m -2 were acquired. Additionally, a new vanadium (V)-microalloyed high Mn alloy was designed to achieve a SFE of 47 mJ·m -2 to minimize planar slip deformation mechanisms. Post-processing via cold working in conjunction with aging was also performed on the V-microalloyed high Mn steel. Hydrogen embrittlement sensitivity was investigated using circumferential notch tensile specimens cathodically charged with hydrogen in a 0.05M NaOH electrolytic solution. The alloys were compared to a cold-worked 316L stainless steel, which exhibited no strength loss due to hydrogen. The high Mn alloys with SFE of ~29 mJ·m 2 and 49 mJ·m -2 had notch strength losses of 11 and 6 pct, respectively. The V-microalloyed high Mn steel in the as-hot-rolled condition had a notch strength loss of 17 pct. Furthermore, the V-microalloyed high Mn steel in the cold worked and aged condition indicated no notch strength loss in hydrogen, which was comparable to the performance of the 316L stainless steel.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Recent Advances in Pipeline Integrity for Transporting Blended Hydrogen-Natural Gas

To achieve US decarbonization goals, hydrogen is being considered as an alternative energy source to reduce carbon emissions. Blending hydrogen into existing natural gas pipelines is an intuitive first step to enable near term emission reductions. However, there are numerous challenges and uncertainties that complicate the transition to transporting hydrogen long-distance through existing natural gas pipelines. The main challenge is hydrogen embrittlement (HE), which reduces the ductility, fracture toughness and fatigue resistance of pipeline steels. This work delivers a technical review on HE effects on the material properties of pipeline carbon steels, such as Grade B, X52, X65, X70, X80, and X100. An important aspect of laboratory tests to capture the HE effect is the hydrogen test environment. This includes hydrogen pre-charged specimens tested in air and specimens tested in a hydrogen gas environment. A review of the mechanical properties of pipeline steel in different hydrogen environments determined through tensile testing is given first, which includes HE effects on yield strength, ultimate tensile strength, and ductility for blended hydrogen-natural gas pipelines. Then, the HE effects on fracture toughness and fatigue crack growth resistance are discussed. Last, impacts of HE to pipeline integrity and major technical challenges are discussed.

: Hydrogen Embrittlement↗
DOE OSTI2026

Impact of Molten Gallium on the Microstructure and Corrosion Behavior of Aluminum and Uranium-Aluminum Alloys for Used Nuclear Fuel Reprocessing

Test reactors around the world utilize highly enriched uranium fuel to achieve high neutron fluxes for materials testing. Once spent, the remaining uranium is a valuable resource for subsequent fuel fabrication. However, some of these test reactor cores consist of curved plate-type fuel elements, fabricated using aluminum alloy 6061 (AA6061) cladding to encapsulate a uranium-aluminum alloy (UAlx) fuel matrix. These assemblies require non-standard reprocessing approaches for uranium recovery, as aluminum dissolves readily in acidic solutions, generating large volumes of waste and complicating downstream chemical separations. In this work, we investigate a novel chemical decladding strategy based on the interaction between AA6061/UAlx and molten gallium (Ga). Ga is known to induce severe degradation of aluminum metal through liquid metal embrittlement (LME), even at relatively low Ga concentrations. By penetrating the aluminum crystal lattice, Ga disrupts grain cohesion and facilitates fracture or dissolution of the aluminum matrix. Thermodynamic analysis of the Al–Ga binary phase diagram suggests that Ga may offer a viable pathway to selectively weaken or dissolve the AA6061 cladding, and potentially the aluminum component of the UAlx fuel matrix within. To this end, parametric experiments were performed at 50 °C and 100 °C across a range of Al–Ga atomic fractions. At lower Al fractions, the AA6061 was completely molten after 2 hours of exposure to the Ga metal. In contrast, samples with higher Al fractions (0.9 Al, 0.1 Ga) contained residual solids after 2 hours, which were characterized by microstructural examination using electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). These Al-Ga compositions were also evaluated using FactSage thermodynamic modeling to further elucidate the relationship between phase diagram behavior and LME.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Materials Genomics Search for Possible Helium‐Absorbing Nano‐Phases in Fusion Structural Materials

Abstract Civilian fusion demands structural materials that can withstand the harsh environments imposed inside fusion plasma reactors. The structural materials often transmute under 14.1 MeV fast neutrons, producing helium (He), which embrittles the grain boundary (GB) network. Here, it is shown that neutron‐friendly and mechanically strong nano‐phases with atomic‐scale free volume can have low He‐embedding energy and >10 at.% He‐absorbing capacity, and can be especially advantageous for soaking up He on top of resisting radiation damage and creep, provided they have thermodynamic compatibility with the matrix phase, satisfactory equilibrium wetting angle, as well as a high enough melting point. The preliminary experimental demonstration proves that is a good ab initio predictor of He shielding potency in nano‐heterophase materials, and thus, is used as a key feature for computational screening. In this context, a list of viable compounds expected to be good He‐absorbing nano‐phases is presented, taking into account , the neutron absorption and activation cross‐sections, the elastic moduli, melting temperature, the thermodynamic compatibility, and the equilbrium wetting angle of the nano‐phases with the Fe matrix as an example.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High Radiation Resistance in the Binary W‐Ta System Through Small V Additions: A New Paradigm for Nuclear Fusion Materials

Abstract Refractory High‐Entropy Alloys (RHEAs) are promising candidates for structural materials in nuclear fusion reactors, where W‐based alloys are currently leading. Fusion materials must withstand extreme conditions, including i) severe radiation damage from energetic neutrons, ii) embrittlement due to H and He ion implantation, and iii) exposure to high temperatures and thermal gradients. Recent RHEAs, such as WTaCrV and WTaCrVHf, have shown superior radiation tolerance and microstructural stability compared to pure W, but their multi‐element compositions complicate bulk fabrication and limit practical use. In this study, it is demonstrated that reducing alloying elements in RHEAs is feasible without compromising radiation tolerance. Herein, two Highly Concentrated Refractory Alloys (HCRAs) − W 53 Ta 44 V 3 and W 53 Ta 42 V 5 (at.%) − were synthesized and investigated. We found that small V additions significantly influence the radiation response of the binary W–Ta system. Experimental results, supported by ab‐initio Monte Carlo simulations and machine‐learning‐driven molecular dynamics, reveal that minor variations in V content enhance Ta–V chemical short‐range order (CSRO), improving radiation resistance in the W 53 Ta 42 V 5 HCRA. By focusing on reducing chemical complexity and the number of alloying elements, the conventional high‐entropy alloy paradigm is challenged, suggesting a new approach to designing simplified multi‐component alloys with refractory properties for thermonuclear fusion applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Effect of annealing and supercritical CO 2 exposure at 750°C on the tensile properties of stainless steel and Ni-based structural alloys

Subsize dogbone tensile specimens of alloys 304H, 310HCbN, and 740H were exposed to 30 MPa supercritical CO 2 (sCO 2 ) for up to 4000 h at 750°C. Similar exposures in laboratory air were used to assess the specific role of sCO 2 exposure on the alloy tensile properties. Type 304H specimens were only embrittled by exposure in sCO 2 due to the formation of a thick Fe-rich oxide and C ingress in the bulk of the alloy. For 310HCbN and 740H, no effect of the sCO 2 environment was observed and a decrease of the alloy's ductility was associated with previously observed microstructure evolutions, for example, grain boundary carbide formation. The 740H was tested in the solution annealed condition and self-aging took place during 750°C exposures in sCO 2 and air with the formation of fine gamma prime precipitates leading to significant tensile strength increase. It was found that both 740H and 310HCbN have adequate sCO 2 compatibility for high-temperature commercial applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Evaluation of coated steels in supercritical CO 2

The carburizing supercritical CO 2 (sCO 2 ) environment limits the use of lower cost steels in the lower temperature (450–650°C) portions of the sCO 2 Brayton cycle because of concerns about internal carburization and embrittlement. Results on a ferritic–martensitic steel and conventional and advanced austenitic steels at 450–650°C in 30 MPa sCO 2 with and without 1% O 2 and 0.1% H 2 O additions have indicated that sCO 2 environments will have lower maximum operating temperatures compared to steam plants. Pack Al and Cr coatings were evaluated at 650°C on T91 and 316H substrates and showed some benefit for up to 2000 h at 650°C, especially without impurities. However, characterization indicated Al 2 O 3 was not formed and Cr-rich carbides formed in the Cr coatings. With the addition of impurities in the sCO 2 , the coatings were less protective at 650°C. Subsequent exposures at 600°C in sCO 2 showed similar behavior. Postexposure evaluations included measuring the bulk C content and room temperature tensile properties. Finally, improvements were indicated but the tensile results were complicated by the high temperature pack coating process affecting the substrate properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A Domestic Program for Liquid Metal PFC Research in Fusion

While high-Z solid plasma-facing components (PFCs) are the leading candidates for reactors, it is unclear that they can survive the intense plasma material interaction (PMI). Liquid metals (LM) PFCs offer potential solutions since they are not susceptible to the same type of damage, and can be “self-healing”. Following the Fusion Energy System Study on Liquid Metal Plasma Facing Components study that recently was completed by Kessel et al. (Fusion Sci Technnol 75:886, 2019) a domestic LM PFC design program has been initiated to develop reactor-relevant LM PFC concepts. This program seeks to evaluate LM PFC concepts for a Fusion Nuclear Science Facility (FNSF) or a Compact Pilot Plant via engineering design calculations, modeling of PMI and PFC components and laboratory experiments. The latter involves experiments in dedicated test stands and confinement devices and seeks to identify and answer open questions in LM PFC design. The new national LM PFC program is first investigating lithium as the plasma facing material for a flowing divertor PFC concept. Several flow speeds will be evaluated, ranging from ~ cm/s to m/s. The surface temperature will initially be held below the strongly evaporative limit in the first design; higher temperatures with strong evaporation will be considered in future concepts. Other topics of interest include: understanding of the hydrogen and helium interaction with the liquid lithium; single effect experiments on wetting, compatibility and embrittlement; and prototypical experiments for control and characterization of flowing LM. A path to plasma and future tokamak exposure of these concepts will be developed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗