Search NASA⌕ Search

SEARCH · Search NASA

Results for “Engine cylinders”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Correlation of the Characteristics of Single-Cylinder and Flight Engines in Tests of High-Performance Fuels in an Air-Cooled Engine I : Cooling Characteristics

Variable charge-air flow, cooling-air pressure drop, and fuel-air ration investigations were conducted to determine the cooling characteristics of a full-scale air-cooled single cylinder on a CUE setup. The data are compared with similar data that were available for the same model multicylinder engine tested in flight in a four-engine airplane. The cylinder-head cooling correlations were the same for both the single-cylinder and the flight engine. The cooling correlations for the barrels differed slightly in that the barrel of the single-cylinder engine runs cooler than the barrel of te flight engine for the same head temperatures and engine conditions.

Wilson, Robert W.↗

A High-speed Engine Pressure Indicator of the Balanced Diaphragm Type

This report describes a pressure-measuring device especially adapted for use in mapping indicator diagrams of high-speed internal combustion engines. The cards are obtained by a point-to-point method giving the average of a large number of engine cycles. The principle involved is the balancing of the engine cylinder pressure against a measured pressure on the opposite side of the metal a diaphragm of negligible stiffness. In its application as an engine indicator the phase of the engine cycle to which a pressure measurement corresponds is selected by a timing device. The report discusses briefly the errors which must be avoided in the development of an indicator for light high-speed engines, where vibration is serious, and outlines the principles underlying the design of this instrument in order to be free of such errors. A detailed description of the instrument and accessories follows together with operating directions.

Dickinson, H C↗

Technology developments for a compound cycle engine

The Compound Cycle Engine (CCE) is a highly turbocharged, power compounded power plant which combines the light weight pressure rise capability of a gas turbine with the high efficiency of a diesel. When optimized for a rotorcraft, the CCE will reduce fuel burned for a typical 2 hour (plus 30 min reserve) mission by 30 to 40 percent when compared to a conventional advanced technology gas turbine. The CCE can provide a 50 percent increase in range-payload product on this mission. Results of recent activities in a program to establish the technology base for a CCE are presented. The objective of this program is to research and develop those critical technologies which are necessary for the demonstration of a multicylinder diesel core in the early 1990s. A major accomplishment was the initial screening and identification of a lubricant which has potential for meeting the material wear rate limits of the application. An in-situ wear measurement system also was developed to provide accurate, readily obtainable, real time measurements of ring and liner wear. Wear data, from early single cylinder engine tests, are presented to show correlation of the in-situ measurements and the system's utility in determining parametric wear trends. A plan to demonstrate a compound cycle engine by the mid 1990s is included.

Bobula, George A.↗

Indicated mean-effective pressure instrument

Device is capable of measuring and calculating IMEP of internal combustion engines in real time. Apparatus is used to provide mass flow measurements in engine cylinder and in measurement of release energy of nonlinear spring.

Rice, W. J.↗

Cast Fe-base cylinder/regenerator housing alloy

The development of an iron-base alloy that can meet the requirements of automotive Stirling engine cylinders and regenerator housings is described. Alloy requirements are as follows: a cast alloy, stress for 5000-hr rupture life of 200 MPa (29 ksi) at 775 C (1427 F), oxidation/corrosion resistance comparable to that of N-155, compatibility with hydrogen, and an alloy cost less than or equal to that of 19-9DL. The preliminary screening and evaluation of ten alloys are described.

Larson, F.↗

Coatings for high-temperature bearings and seals

Criteria are discussed for predicting the probable lubricating ability of candidate solid materials from a consideration of their basic chemical and physical properties. The properties considered to be important in the model are thermochemical potential, adhesion, low hardness, plasticity, yield strength in shear, and brittle-to-ductile transition characteristics. A review of the selection and tribological testing of materials, which were selected for use in self-lubricating composite coatings by employing this model, is given. Two series of plasma-sprayed coatings with good tribological properties over a wide temperature spectrum are described. The PS 100 series of coatings contain oxidatively stable solid lubricants in a nichrome matrix. The PS 200 series contains the same solid lubricants in a very wear resistant metal-bonded chromium carbide matrix. Examples are given of applications of these coatings in high speed shaft seals, sliding contact bearings, and Stirling engine cylinder liners.

Sliney, Harold E.↗

Disturbing effect of free hydrogen on fuel combustion in internal combustion engines

Experiments with fuel mixtures of varying composition, have recently been conducted by the Motor Vehicle and Airplane Engine Testing Laboratories of the Royal Technical High School in Berlin and at Fort Hahneberg, as well as at numerous private engine works. The behavior of hydrogen during combustion in engines and its harmful effect under certain conditions, on the combustion in the engine cylinder are of general interest. Some of the results of these experiments are given here, in order to elucidate the main facts and explain much that is already a matter of experience with chauffeurs and pilots.

Riedler, A↗

Rate of Heat Transfer from Finned Metal Surfaces

The object was to evaluate the factors which control the rate of heat transfer to a moving current of air from finned metal surfaces similar to those used on aircraft engine cylinders. The object was to establish data which will enable the finning of cooling surfaces to be designed to suit the particular needs of any specific application. Most of the work was done on flat copper specimens 6 inches square, upon which were mounted copper fins with spacings varying from 1/2 inch to 1/12 inch. All fins were 1 inch deep, 6 inches long, and .020 inch thick. The results of the investigation are given in the form of curves included here. In general, it was found that for specimens of this kind, the effectiveness of a given fin does not decrease very rapidly until its distance from adjacent fins has been reduced to 1/9 or 1/10 of an inch. A formula for the heat transfer from a flat surface without fins was developed, and an approximate formula for the finned specimens is suggested.

Taylor, G Fayette↗

Development of an Impinging-jet Fuel-injection Valve Nozzle

During an investigation to determine the possibilities and limitations of a two-stroke-cycle engine and ignition, it was necessary to develop a fuel injection valve nozzle to produce a disk-shaped, well dispersed spray. Preliminary tests showed that two smooth jets impinging upon each other at an angle of 74 degrees gave a spray with the desired characteristics. Nozzles were built on this basis and, when used in fuel-injection valves, produced a spray that fulfilled the original requirements. The spray is so well dispersed that it can be carried along with an air stream of comparatively low velocity or entrained with the fuel jet from a round-hole orifice. The characteristics of the spray from an impinging-jet nozzle limits its application to situations where wide dispersion is required by the conditions in the engine cylinder and the combustion chamber.

Spanogle, J A↗

Drag Tests of 4/9-Scale Model Engine Nacelles with Various Cowlings

Results are given of drag tests of 4/9-scale model radial air-cooled engine nacelles made as a part of a general investigation of wing-nacelle-propeller interference. A small nacelle of the type commonly used with exposed engine cylinders was tested with various forms of cowling over the cylinders. The effects of cowling-ring position and of angle of ring chord to the thrust line were investigated. An N.A.C.A. cowled nacelle and a smooth body were also tested. The results are given at 50, 75, and 100 miles per hour for -5 degrees, 0 degrees, 5 degrees, 10 degrees, 15 degrees angle of pitch.

Windler, Ray↗

The Effect of Propellers and Nacelles on the Landing Speeds of Tractor Monoplanes

This paper reports wind-tunnel tests giving the lift coefficients of large-scale wing-nacelle combinations both with and without the propeller. The tests were made to show the effect of nacelles, and idling and stopped propellers on the landing speeds of tractor monoplanes. Four types of nacelles with various cowlings were used in numerous positions with respect to both a Clark Y and a thick airfoil. The effect of both the idling and stopped propeller on lift, and consequently on landing speed, was negligible. A nacelle with exposed engine cylinders when placed directly in front of an airfoil caused a slight reduction in lift, consequently an increase in landing speed, over the condition with the wing alone. With this exception no appreciable effect on landing speed was indicated for any of the other combinations.

Windler, Ray↗

Wind-tunnel Tests of Carburetor-intake Rams

An investigation was conducted in the NACA 20-foot wind tunnel of the ramming effect of three general types of carburetor intake rams for radial engines, namely, the internal constant area type, the external constant area type, and the external expanding type. The rams were installed on a radial air- cooled engine nacelle, and tests were made with and without the propeller operating. The results indicated that the external types having entrances near the front of the engine cowling gave the greatest ramming effect. The propeller increased the ramming effect for the external types. From considerations of the ramming effect, the best entrance location for the external types was close to the nose of the engine cowling. For the internal type, the best location was in a plane perpendicular to the propeller shaft and immediately forward of the engine cylinders.

Highley, Frank H↗

Turbulator for a liner cooling jacket

A turbulator for a liner cooling jacket includes a metal panel which is suitable to be coiled into a generally cylindrical shape so as to be placed in a relief area between an engine cylinder block and a cylinder liner. The relief area may be machined into either the block or the cylinder liner and the metal panel is formed with a pattern of protuberances shaped like corrugations. In one embodiment, the corrugations have a shape similar to a sine wave and are arranged in a plurality of generally parallel axial segments. The corrugation wave pattern of one segment may be the same as its adjacent segment or may be staggered by one corrugation which would mean one-half of a full wave cycle. The corrugation pattern in the turbulator panel may be created by any one of various stamping or forming operations and when placed between the cylinder liner and block, increases turbulence of the cooling liquid in order to enhance heat transfer.

Hoag, Kevin L.↗

Fuels Containing Methane of Natural Gas in Solution

While exploring ways of producing better fuels for propulsion of a spacecraft on the Mars sample return mission, a researcher at Johnson Space Center (JSC) devised a way of blending fuel by combining methane or natural gas with a second fuel to produce a fuel that can be maintained in liquid form at ambient temperature and under moderate pressure. The use of such a blended fuel would be a departure for both spacecraft engines and terrestrial internal combustion engines. For spacecraft, it would enable reduction of weights on long flights. For the automotive industry on Earth, such a fuel could be easily distributed and could be a less expensive, more efficient, and cleaner-burning alternative to conventional fossil fuels. The concept of blending fuels is not new: for example, the production of gasoline includes the addition of liquid octane enhancers. For the future, it has been commonly suggested to substitute methane or compressed natural gas for octane-enhanced gasoline as a fuel for internal-combustion engines. Unfortunately, methane or natural gas must be stored either as a compressed gas (if kept at ambient temperature) or as a cryogenic liquid. The ranges of automobiles would be reduced from their present values because of limitations on the capacities for storage of these fuels. Moreover, technical challenges are posed by the need to develop equipment to handle these fuels and, especially, to fill tanks acceptably rapidly. The JSC alternative to provide a blended fuel that can be maintained in liquid form at moderate pressure at ambient temperature has not been previously tried. A blended automotive fuel according to this approach would be made by dissolving natural gas in gasoline. The autogenous pressure of this fuel would eliminate the need for a vehicle fuel pump, but a pressure and/or flow regulator would be needed to moderate the effects of temperature and to respond to changing engine power demands. Because the fuel would flash as it entered engine cylinders, relative to gasoline, it would disperse more readily and therefore would mix with air more nearly completely. As a consequence, this fuel would burn more nearly completely (and, hence, more cleanly) than gasoline does. The storage density of this fuel would be similar to that of gasoline, but its energy density would be such that the mileage (more precisely, the distance traveled per unit volume of fuel) would be greater than that of either gasoline or compressed natural gas. Because the pressure needed to maintain the fuel in liquid form would be more nearly constant and generally lower than that needed to maintain compressed natural gas in liquid form, the pressure rating of a tank used to hold this fuel could be lower than that of a tank used to hold compressed natural gas. A mixture of natural gas and gasoline could be distributed more easily than could some alternative fuels. A massive investment in new equipment would not be necessary: One could utilize the present fuel-distribution infrastructure and could blend the gasoline and natural gas at almost any place in the production or distribution process - perhaps even at the retail fuel pump. Yet another advantage afforded by use of a blend of gasoline and natural gas would be a reduction in the amount of gasoline consumed. Because natural gas costs less than gasoline does and is in abundant supply in the United States, the cost of automotive fuel and the demand for imported oil could be reduced.

Sullivan, Thomas A.↗

The Charging Process in a High-speed, Single-cylinder, Four-stroke Engine

Experimental measurements and theoretical calculations were made on an aircraft-type, single cylinder engine, in order to determine the physical nature of the inlet process, especially at high piston speeds. The engine was run at speeds from 1,500 to 2,600 r.p.m. (mean piston speeds of 1,370 to 2,380 feet per minute). Measurements were made of the cylinder pressure during the inlet stroke and of the power output and volumetric efficiency. Measurements were also made, with the engine not running, to determine the resistance and mass of air in the inlet valve port at various crank angles. Results of analysis indicate that mass has an appreciable effect, but friction plays the major part in restricting flow. The observed fact that the volumetric efficiency is considerably less than 100 percent is attributed to thermal effects. An estimate was made of the magnitude of these effects in the present case, and their general nature is discussed.

Reynolds, Blake↗

Supercharged two-cycle engines employing novel single element reciprocating shuttle inlet valve mechanisms and with a variable compression ratio

This invention relates to novel reciprocating shuttle inlet valves, effective with every type of two-cycle engine, from small high-speed single cylinder model engines, to large low-speed multiple cylinder engines, employing spark or compression ignition. Also permitting the elimination of out-of-phase piston arrangements to control scavenging and supercharging of opposed-piston engines. The reciprocating shuttle inlet valve (32) and its operating mechanism (34) is constructed as a single and simple uncomplicated member, in combination with the lost-motion abutments, (46) and (48), formed in a piston skirt, obviating the need for any complex mechanisms or auxiliary drives, unaffected by heat, friction, wear or inertial forces. The reciprocating shuttle inlet valve retains the simplicity and advantages of two-cycle engines, while permitting an increase in volumetric efficiency and performance, thereby increasing the range of usefulness of two-cycle engines into many areas that are now dominated by the four-cycle engine.

Wiesen, Bernard↗