Search NASA⌕ Search

SEARCH · Search NASA

Results for “Euler angles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Light bending by nonlinear electrodynamics under strong electric and magnetic field

We calculate the bending angles of light under the strong electric and magnetic fields by a charged black hole and a magnetized neutron star according to the nonlinear electrodynamics of Euler-Heisenberg interaction. The bending angle of light by the electric field of charged black hole is computed from geometric optics and a general formula is derived for light bending valid for any orientation of the magnetic dipole. The astronomical significance of the light bending by magnetic field of a neutron star is discussed.

79 ASTRONOMY AND ASTROPHYSICS↗

Reusable Launch Vehicle Attitude Control Using a Time-Varying Sliding Mode Control Technique

In this paper we present a time-varying sliding mode control (TVSMC) technique for reusable launch vehicle (RLV) attitude control in ascent and entry flight phases. In ascent flight the guidance commands Euler roll, pitch and yaw angles, and in entry flight it commands the aerodynamic angles of bank, attack and sideslip. The controller employs a body rate inner loop and the attitude outer loop, which are separated in time-scale by the singular perturbation principle. The novelty of the TVSMC is that both the sliding surface and the boundary layer dynamics can be varied in real time using the PD-eigenvalue assignment technique. This salient feature is used to cope with control command saturation and integrator windup in the presence of severe disturbance or control effector failure, which enhances the robustness and fault tolerance of the controller. The TV-SMC ascent and descent designs are currently being tested with high fidelity, 6-DOF dispersion simulations. The test results will be presented in the final version of this paper.

Shtessel, Yuri B.↗

Improved Re-Configurable Sliding Mode Controller for Reusable Launch Vehicle of Second Generation Addressing Aerodynamic Surface Failures and Thrust Deficiencies

In this report we present a time-varying sliding mode control (TV-SMC) technique for reusable launch vehicle (RLV) attitude control in ascent and entry flight phases. In ascent flight the guidance commands Euler roll, pitch and yaw angles, and in entry flight it commands the aerodynamic angles of bank, attack and sideslip. The controller employs a body rate inner loop and the attitude outer loop, which are separated in time-scale by the singular perturbation principle. The novelty of the TVSMC is that both the sliding surface and the boundary layer dynamics can be varied in real time using the PD-eigenvalue assignment technique. This salient feature is used to cope with control command saturation and integrator windup in the presence of severe disturbance or control effector failure, which enhances the robustness and fault tolerance of the controller. The TV-SMC is developed and tuned up for the X-33 sub-orbital technology demonstration vehicle in launch and re-entry modes. A variety of nominal, dispersion and failure scenarios have tested via high fidelity 6DOF simulations using MAVERIC/SLIM simulation software.

Shtessel, Yuri B.↗

Aerodynamic characteristics of missile control fins in nonlinear flow fields

Recent experimental results show that the control effectiveness of a missile fin in supersonic flow at moderate-to-high angles of attack is a strong nonlinear function of free-stream Mach number, body incidence angle, fin bank angle and fin deflection angle. Analysis of the experimental results using an Euler finite-difference computer code with flow separation together with the equivalent angle-of-attack concept indicates that the observed nonlinearities are due to the variation of local dynamic pressure and local Mach number around the missile body alone. The nonlinearities are shown to be a strong source of control cross-coupling for high Mach number, high angle-of-attack combinations. The analysis suggests a relatively simple yet comprehensive approach for accurately accounting for these nonlinear effects.

Hemsch, M. J.↗

Flow analysis for the nacelle of an advanced ducted propeller at high angle-of-attack and at cruise with boundary layer control

An axisymmetric panel code and a three dimensional Navier-Stokes code (used as an inviscid Euler code) were verified for low speed, high angle of attack flow conditions. A three dimensional Navier-Stokes code (used as an inviscid code), and an axisymmetric Navier-Stokes code (used as both viscous and inviscid code) were also assessed for high Mach number cruise conditions. The boundary layer calculations were made by using the results from the panel code or Euler calculation. The panel method can predict the internal surface pressure distributions very well if no shock exists. However, only Euler and Navier-Stokes calculations can provide a good prediction of the surface static pressure distribution including the pressure rise across the shock. Because of the high CPU time required for a three dimensional Navier-Stokes calculation, only the axisymmetric Navier-Stokes calculation was considered at cruise conditions. The use of suction and tangential blowing boundary layer control to eliminate the flow separation on the internal surface was demonstrated for low free stream Mach number and high angle of attack cases. The calculation also shows that transition from laminar flow to turbulent flow on the external cowl surface can be delayed by using suction boundary layer control at cruise flow conditions. The results were compared with experimental data where possible.

Hwang, D. P.↗

Prediction of Aerodynamic Coefficient using Genetic Algorithm Optimized Neural Network for Sparse Data

Wind tunnels use scale models to characterize aerodynamic coefficients, Wind tunnel testing can be slow and costly due to high personnel overhead and intensive power utilization. Although manual curve fitting can be done, it is highly efficient to use a neural network to define the complex relationship between variables. Numerical simulation of complex vehicles on the wide range of conditions required for flight simulation requires static and dynamic data. Static data at low Mach numbers and angles of attack may be obtained with simpler Euler codes. Static data of stalled vehicles where zones of flow separation are usually present at higher angles of attack require Navier-Stokes simulations which are costly due to the large processing time required to attain convergence. Preliminary dynamic data may be obtained with simpler methods based on correlations and vortex methods; however, accurate prediction of the dynamic coefficients requires complex and costly numerical simulations. A reliable and fast method of predicting complex aerodynamic coefficients for flight simulation I'S presented using a neural network. The training data for the neural network are derived from numerical simulations and wind-tunnel experiments. The aerodynamic coefficients are modeled as functions of the flow characteristics and the control surfaces of the vehicle. The basic coefficients of lift, drag and pitching moment are expressed as functions of angles of attack and Mach number. The modeled and training aerodynamic coefficients show good agreement. This method shows excellent potential for rapid development of aerodynamic models for flight simulation. Genetic Algorithms (GA) are used to optimize a previously built Artificial Neural Network (ANN) that reliably predicts aerodynamic coefficients. Results indicate that the GA provided an efficient method of optimizing the ANN model to predict aerodynamic coefficients. The reliability of the ANN using the GA includes prediction of aerodynamic coefficients to an accuracy of 110% . In our problem, we would like to get an optimized neural network architecture and minimum data set. This has been accomplished within 500 training cycles of a neural network. After removing training pairs (outliers), the GA has produced much better results. The neural network constructed is a feed forward neural network with a back propagation learning mechanism. The main goal has been to free the network design process from constraints of human biases, and to discover better forms of neural network architectures. The automation of the network architecture search by genetic algorithms seems to have been the best way to achieve this goal.

Rajkumar, T.↗

Treatment of conical and nonconical supersonic flows by an implicit marching scheme applied to the full potential equation

An aerodynamic prediction technique based on the full potential equation in conservation form is developed for the treatment of supersonic flows. This technique bridges the gap between simplistic linear theory methods and complex Euler solvers. A novel local density linearization concept and a second order accurate retarded density scheme, both producing the correct artificial viscosity, are introduced in developing an implicit marching scheme for solving the scalar potential. Results for conical flows over delta wings and a wing-body combination and for non-conical flows over bodies of revolution at angles of attack are compared with Euler and nonconservative full potential calculations and experimental data. The present formulation requires an order of magnitude less computer time and significantly less computer memory over Euler codes and exhibits a considerable improvement in computational efficiency and generality over an existing nonconservative full potential code.

Shankar, V.↗

Prediction of Unsteady Blade Surface Pressures on an Advanced Propeller at an Angle of Attack

The numerical solution of the unsteady, three-dimensional, Euler equations is considered in order to obtain the blade surface pressures of an advanced propeller at an angle of attack. The specific configuration considered is the SR7L propeller at cruise conditions with a 4.6 deg inflow angle corresponding to the plus 2 deg nacelle tilt of the Propeller Test Assessment (PTA) flight test condition. The results indicate nearly sinusoidal response of the blade loading, with angle of attack. For the first time, detailed variations of the chordwise loading as a function of azimuthal angle are presented. It is observed that the blade is lightly loaded for part of the revolution and shocks appear from hub to about 80 percent radial station for the highly loaded portion of the revolution.

Nallasamy, M.↗

Investigation of vortex breakdown on a delta wing using Euler and Navier-Stokes equations

A numerical investigation of leading-edge vortex breakdown on a delta wing at high angles of attack is presented. The analysis has been restricted to low speed flows on a flat plate wing with sharp leading edges. Both Euler and Navier-Stokes (assuming fully laminar and fully turbulent flows) equations have been used in this study and the results are compared against experimental data. Predictions of vortex breakdown progression with angle of attack with both Euler and Navier-Stokes equations are shown to be consistent with the experimental data. However, the Navier-Stokes predictions show significant improvements in breakdown location at angles of attack where the vortex breakdown approaches the wing apex. The location of the primary vortex and the level of vorticity in the pre-breakdown regions in these flowfield solutions are affected very little by the viscous effects, even though the Navier-Stokes solutions exhibit viscous phenomena such as secondary and tertiary vortices which are not present in the Euler solutions. In the post-breakdown regions, however, the levels of vorticity in the primary vortex have increased differences between the Euler and Navier-Stokes solutions at comparable locations. Navier-Stokes indicates the presence of a secondary vortex even after the primary vortex is burst. The predicted trajectories of the primary vortex are in very good agreement with the test data, the laminar solutions providing the overall best comparison. The Euler shows a small displacement of the primary vortex, relative to experiment, due to the lack of secondary vortices. The turbulent Navier-Stokes, in general, fall between the Euler and laminar solutions. These findings are based on solutions from meshes that are not usually considered fine enough for resolving vortical flows. To further understand the vortex breakdown phenomenon and the fine details of the vortical flow structure, further calculations with the finer meshes and improved turbulence models are necessary.

S. Agrawal↗

Two-dimensional transonic wind-tunnel wall interference corrections based on the Euler equations

A procedure for the evaluation of wall interference corrections for two-dimensional models is presented. The Mach number and angle-of-attack corrections require the numerical solution of the Euler equations. Pressure measurements are required near the wind tunnel walls. The correction procedure also requires knowledge of the free-stream Mach number, the model geometry, and the lift force experienced by the model. The residual interference not accounted for by the Mach number and angle-of-attack corrections is estimated.

Rizk, M. H.↗

Characteristics and performance of the first commercial multileaf collimator for a robotic radiosurgery system

Purpose: The “InCise™ multileaf-collimator (MLC)” is the first commercial MLC to be mounted on a robotic SRS/SBRT platform (CyberKnife). The authors assessed characteristics and performance of this novel device in a preclinical five months test period. Methods: Commissioning beam data were acquired with unshielded diodes. EBT3 radiochromic films were employed for measurement of transmission, leaf/bank position accuracy (garden fence) before and after exercising the MLC, for end-to-end testing and further characterization of the beam. The robot workspace with MLC was assessed analytically by transformation to an Euler geometry (“plane,” “gantry,” and “collimator” angles) and by measuring pointing accuracy at each node. Stability over time was evaluated in picket fence and adapted Winston–Lutz tests (AQA). Results: Beam penumbrae (80%–20%, with 100% = 2 × dose at inflection point for field sizes ≥ 50 × 50 mm{sup 2}) were 2.2–3.7 mm for square fields in reference condition (source-axis-distance 800 mm, depth 15 mm) and depended on field size and off-axis position. Transmission and leakage did not exceed 0.5%. Accessible clinical workspace with MLC covered non-coplanar gantry angles of [−113°; +112°] and collimator angles of [−100°; +107°], with an average robot pointing accuracy of 0.12 ± 0.09 mm. For vertical beams, garden fence tests exhibited an average leaf positioning error of ≤0.2 mm, which increased by 0.25 and 0.30 mm (banks X1 and X2) with leaves traveling parallel to gravity. After execution of a leaf motion stress routine, garden fence tests showed slightly increased jaggedness and allowed to identify one malfunctioning leaf motor. Total system accuracy with MLC was 0.38 ± 0.05 mm in nine end-to-end tests. Picket fence and AQA tests displayed stable results over the test period. Conclusions: The InCise™ MLC for CyberKnife showed high accuracy and adequate characteristics for SRS/SBRT applications. MLC performance after exercise demands specific quality assurance measures.

60 APPLIED LIFE SCIENCES↗

Optimal symmetric flight with an intermediate vehicle model

The present investigation is concerned with an examination of optimal symmetry flight on the basis of the intermediate vehicle model. The analysis is partly based upon an exploration of Euler solutions for the path-angle-as-control model carried out by Kelley (1958). The current analysis takes into account higher-order optimality conditions and 'chattering-control' phenomena. Attention is given to details regarding the intermediate vehicle model, the Legendre-Clebsch necessary condition, the conjugate-point test, and the numerical solution of the time-range problem. It is found that the flight path angle takes on the role of control variable in the model. From physical considerations, it can be seen that when a positive margin of thrust over drag exists, the maximum-range climb trajectory without time or fuel constraints has no proper maximum nor an upper bound.

Kelley, H. J.↗

Optimal symmetric flight with an intermediate vehicle model

The present investigation is concerned with an examination of optimal symmetry flight on the basis of the intermediate vehicle model. The analysis is partly based upon an exploration of Euler solutions for the path-angle-as-control model carried out by Kelley (1958). The current analysis takes into account higher-order optimality conditions and "chattering-control' phenomena. Attention is given to details regarding the intermediate vehicle model, the Legendre-Clebsch necessary condition, the conjugate-point test, and the numerical solution of the time-range problem. It is found that the flight path angle takes on the role of control variable in the model. From physical considerations, it can be seen that when a positive margin of thrust over drag exists, the maximum-range climb trajectory without time or fuel constraints has no proper maximum nor an upper bound.

Menon, P. K. A.↗

Prediction of unsteady blade surface pressures on an advanced propeller at an angle of attack

The paper considers the numerical solution of the unsteady, three-dimensional, Euler equations to obtain the blade surface pressures of an advanced propeller at an angle of attack. The specific configuration considered is the SR7L propeller at cruise conditions with a 4.6 deg inflow angle corresponding to the +2 deg nacelle tilt of the Propeller Test Assessment (PTA) flight test condition. The results indicate nearly sinusoidal response of the blade loading, with angle of attack. For the first time, detailed variations of the chordwise loading as a function of azimuthal angle are presented. It is observed that the blade is lightly loaded for part of the revolution and shocks appear from hub to about 80 percent radial station for the highly loaded portion of the revolution.

Nallasamy, M.↗

On the use of a three-dimensional Navier-Stokes solver for rocket engine pump impeller design

A 3D Reynolds-averaged Navier-Stokes Solver and a Fast Grid Generator (FGG), developed specially for centrifugal impeller design, were incorporated into the pump impeller design process. The impeller performance from the CFD analysis was compared to one-dimensional prediction. Both analyses showed good agreement of the impeller hydraulic efficiency, 94.5 percent, but with an 8 percent discrepancy of Euler head prediction. The impeller blade angle, discharge hub to shroud width, axial length and blade stacking were systematically changed to achieve an optimum impeller design. Impeller overall efficiency, loss distribution, hub-to-tip flow angle distortion and blade-to-blade flow angle change are among those criteria used to evaluate impeller performance. Two grid sizes, one with 10 K grid points and one with 80 K grid points were used to evaluate grid dependency issues. The effects of grid resolution on the accuracy and turnaround time are discussed. In conclusion, it is demonstrated that CFD can be effectively used for design and optimization of rocket engine pump components.

Chen, Wei-Chung↗

The Initial Orbit Determination (IOD) Problem With Range, Range-Rate and Angles

The Initial Orbit Determination (IOD) problem has been tacked since Laplace, Euler and Gauss in the service of determining the orbits of planets, asteroids, and comets. The measurements that established the orbit characteristics were angles over long arcs.1 The Space Age brought two new measurement types to bear: range and range-rate.2, 3 Initially these measurements were provided by radars through skin-tracking. Soon, however, transponders allowed better measurement accuracy and availability. To date, there are three types of IOD problems: angles only, range and angles, and range and range-rate. The Orion program exposed the need for an additional capability in the case of an extended loss of communication: when the measurements included antenna angles (azimuth and elevation or right-ascension and declination), range and range-rate. This paper contains the details of this new methodology. We will begin with state determination with range, range-rate and angle measurements. First the state estimate, given a sequence of these four time-synchronized measurements, will be analytically developed. Next the covariance matrix associated with this state estimate will be analytically developed. Finally, these will be verified by Monte Carlo simulations.

Christopher D’Souza↗

Unsteady blade pressures on a propfan at takeoff: Euler analysis and flight data

The unsteady blade pressures due to the operation of the propfan at an angle to the direction of the mean flow are obtained by solving the unsteady three dimensional Euler equations. The configuration considered is the eight bladed SR7L propfan at takeoff conditions and the inflow angles considered are 6.3 deg, 8.3 deg, 11.3 deg. The predicted blade pressure waveforms are compared with inflight measurements. At the inboard radial station (r/R = 0.68) the phase of the predicted waveforms show reasonable agreement with the measurements while the amplitudes are over predicted in the leading edge region of the blade. At the outboard radial station (r/R = 0.95), the predicted amplitudes of the waveforms on the pressure surface are in good agreement with flight data for all inflow angles. The measured (installed propfan) waveforms show a relative phase lag compared to the computed (propfan alone) waveforms. The phase lag depends on the axial location of the transducer and the surface of the blade. On the suction surface, in addition to the relative phase lag, the measurements show distortion (widening and steepening) of the waveforms. The extent of distortion increases with increase in inflow angle. This distortion seems to be due to viscous separation effects which depend on the azimuthal location of the blade and the axial location of the transducer.

Nallasamy, M.↗

Unsteady blade pressures on a propfan at takeoff - Euler analysis and flight data

The unsteady blade pressures due to the operation of the propfan at an angle to the direction of the mean flow are obtained by solving the unsteady three dimensional Euler equations. The configurations considered is the eight bladed SR7L propfan at takeoff conditions and the inflow angles considered are 6.3 deg, 8.3 deg, 11.3 deg. The predicted blade pressure waveforms are compared with inflight measurements. At the inboard radial station (r/R = 0.68) the phase of the predicted waveforms show reasonable agreement with the measurements while the amplitudes are over predicted in the leading edge region of the blade. At the outboard radial station (r/R = 0.95), the predicted amplitudes of the waveforms on the pressure surface are in good agreement with flight data for all inflow angles. The measured (installed propfan) waveforms show a relative phase lag compared to the computed (propfan alone) waveforms. The phase lag depends on the axial location of the transducer and the surface of the blade. On the suction surface, in addition to the relative phase lag, the measurements show distortion (widening and steepening) of the waveforms. The extend of distortion increases with increase in inflow angle. This distortion seems to be due to viscous separation effects which depend on the azimuthal location of the blade and the axial location of the transducer.

Nallasamy, M.↗