Search NASA⌕ Search

SEARCH · Search NASA

Results for “FEEDBACK AMPLIFIER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Electronic Neural Networks

Memory based on neural network models content-addressable and fault-tolerant. System includes electronic equivalent of synaptic network; particular, matrix of programmable binary switching elements over which data distributed. Switches programmed in parallel by outputs of serial-input/parallel-output shift registers. Input and output terminals of bank of high-gain nonlinear amplifiers connected in nonlinear-feedback configuration by switches and by memory-prompting shift registers.

Lambe, John↗

p-MOSFET total dose dosimeter

A p-MOSFET total dose dosimeter where the gate voltage is proportional to the incident radiation dose. It is configured in an n-WELL of a p-BODY substrate. It is operated in the saturation region which is ensured by connecting the gate to the drain. The n-well is connected to zero bias. Current flow from source to drain, rather than from peripheral leakage, is ensured by configuring the device as an edgeless MOSFET where the source completely surrounds the drain. The drain junction is the only junction not connected to zero bias. The MOSFET is connected as part of the feedback loop of an operational amplifier. The operational amplifier holds the drain current fixed at a level which minimizes temperature dependence and also fixes the drain voltage. The sensitivity to radiation is made maximum by operating the MOSFET in the OFF state during radiation soak.

Buehler, Martin G.↗

Predictability of the Minimum Sea Ice Extent from Late Winter Fram Strait Ice Export: Model vs Observations

Late winter coastal divergence along the Eurasian coastline (referred to as the ice factory) – or the Fram Strait ice export, a proxy for coastal divergence in the ice factory – is a skillful predictor of the minimum sea ice extent (Williams et al., 2016; Brunette et al., 2018; Sesternikov and, 1979). Coastal divergence leads to the formation of coastal polynya where new ice grows but to a thickness that is not large enough to survive the following summer melt. This signal is then amplified by the ice albedo feedback and leads to more open water at the end of the summer melt season. In this thesis project, we will identify if this source of predictive skill in the seasonal forecast of the minimum sea ice extent is present in General Circulation Models, more precisely in the CESM2-LE, GISS-E2.1-G, GFDL FLOR-LE, CNRM-CM6-1 and the CanESM5. Since even small biases in the large-scale atmospheric circulation simulated by a model can short circuit this coupling between dominant modes of atmospheric variability (NAO and AO), coastal divergence along the Eurasian coastline, Fram Strait ice export and therefore seasonal forecasting skill of the model, failure to reproduce this coupling observed in the real Arctic will be used to identify biases in GCM. Preliminary results show that subtle changes in the large-scale atmospheric circulation leads to opposite statistical relationship between Fram Strait ice area export, coastal divergence along the Eurasian coastline, and seasonal predictability of the minimum sea ice extent both in the CESM2-LE and the GISS-E2.1-G models. Differences are linked with the partitioning between recirculation within the Beaufort Gyre, ice exported through Fram Strait and ridging north of the Canadian Arctic Archipelago.

Sea ice↗

Method and apparatus for reducing microwave oscillator output noise

Microwave oscilltors incorporate r.f. feedback with carrier suppression to reduce phase noise. In a direct feedback oscillator arrngement a circulator is interposed between the r.f. amplifier and the high-Q resonator. The amplifier output is applied to the slightly over-coupled input port of the resonator so that the resultant net return signal is the vectorial difference between the signals emitted and reflected from the resonator. The gain of the r.f. amplifier is chosen to regenerate the forward signal from the net return signal. In a STALO-type arrangement, the resonator is critically coupled and an r.f. amplifier added to the path of the net return signal. The sensitivity of the STALO-type feedback loop is thereby enhanced while added amplifier noise is minimized by the superposition of the signals emitted by and reflected from the resonator.

Dick, G. John↗

Active lamp pulse driver circuit

A flashlamp drive circuit is described which uses an unsaturated transistor as a current mode switch to periodically subject a partially ionized gaseous laser excitation flashlamp to a stable, rectangular pulse of current from an incomplete discharge of an energy storage capacitor. A monostable multivibrator sets the pulse interval, initiating the pulse in response to a flash command by providing a reference voltage to a non-inverting terminal of a base drive amplifier; a tap on an emitter resistor provides a feedback signal sensitive to the current amplitude to an inverting terminal of amplifier, thereby controlling the pulse amplitude. The circuit drives the flashlamp to provide a squarewave current flashlamp discharge.

Logan, K. E.↗

Recent advances in capacitance type of blade tip clearance measurements

Two recent electronic advances at NASA-Lewis that meet the blade tip clearance needs of a wide class of fans, compressors, and turbines are described. The first is a frequency modulated (FM) oscillator that requires only a single low cost ultrahigh frequency operational amplifier. Its carrier frequency is 42.8 MHz when used with a 61 cm long hermetically sealed coaxial cable. The oscillator can be calibrated in the static mode and has a negative peak frequency deviation of 400 kHz for a typical rotor blade. High temperature performance tests of the probe and 13 cm of the adjacent cable show good accuracy up to 600 C, the maximum which produces a clearance error of + or - 10 microns at a clearance of 500 microns. In the second advance, a guarded probe configuration allows a longer cable capacitance. The capacitance of the probe is part of a small time constant feedback in a high speed operational amplifier. The solution of the governing differential equation is applied to a ramp type of input. The results show an amplifier output that contains a term which is proportional to the derivative of the feedback capacitance. The capacitance is obtained by subtracting a balancing reference channel followed by an integration stage.

Barranger, John P.↗

Recent advances in capacitance type of blade tip clearance measurements

Two recent electronic advances at NASA-Lewis that meet the blade tip clearance needs of a wide class of fans, compressors, and turbines are described. The first is a frequency modulated (FM) oscillator that requires only a single low cost ultrahigh frequency operational amplifier. Its carrier frequency is 42.8 MHz when used with a 61 cm long hermetically sealed coaxial cable. The oscillator can be calibrated in the static mode and has a negative peak frequency deviation of 400 kHz for a typical rotor blade. High temperature performance tests of the probe and 13 cm of the adjacent cable show good accuracy up to 600 C, the maximum which produces a clearance error of + or - 10 microns at a clearance of 500 microns. In the second advance, a guarded probe configuration allows a longer cable capacitance. The capacitance of the probe is part of a small time constant feedback in a high speed operational amplifier. The solution of the governing differential equation is applied to a ramp type of input. The results show an amplifier output that contains a term which is proportional to the derivative of the feedback capacitance. The capacitance is obtained by subtracting a balancing reference channel followed by an integration stage.

Barranger, John P.↗

Simple Optoelectronic Feedback in Microwave Oscillators

A proposed method of stabilizing microwave and millimeter-wave oscillators calls for the use of feedback in optoelectronic delay lines characterized by high values of the resonance quality factor (Q). The method would extend the applicability of optoelectronic feedback beyond the previously reported class of optoelectronic oscillators that comprise two-port electronic amplifiers in closed loops with high-Q feedback circuits.

Maleki, Lute↗

Feedback Processes and Climate Response

The response of the climate system to an external perturbation--e.g., a change in solar irradiance or a change in atmospheric opacity due to an increase in CO2--depends rather strongly on feedback processes in the system, which either amplify or dampen the effects of the initial perturbation. A simple representation of the climate system is used to compare several important feedbacks, based upon general circulation model (GCM) simulations by various investigators. The models are in general agreement with respect to water vapor feedback, but in wide disagreement with respect to cloud feedback. Because of the arguments raised by Lindzen (1990)--that the processes which determine water vapor mixing ratio in the upper atmosphere are quite different from those which operate in the planetary boundary layer, and that upper tropospheric water vapor might actually decrease even when the boundary layer is getting warmer and more moist--researchers undertook a study to determine the sensitivity of climate to changes in water vapor at various levels in the troposphere. The result is that climate is just as sensitive to percentage changes in upper tropospheric water vapor, where the mixing ratio is very small, as it is to percentage changes in the boundary layer, which contains the bulk of total column water vapor.

Arking, Albert↗

Bio-isolated dc operational amplifier

A bio-isolated dc operational amplifier is described for use in making bioelectrical measurements of a patient while providing isolation of the patient from electrical shocks. The circuit contains a first operational amplifier coupled to the patient with its output coupled in a forward loop through a first optic coupler to a second operational amplifier. The output of the second operational amplifier is coupled to suitable monitoring circuitry via a feedback circuit including a second optic coupler to the input of the first operational amplifier.

Lee, R. D.↗

CW ultrasonic bolt tensioning monitor

A CW ultrasonic device is described for measuring frequency shifts of the peak of a mechanical resonance in a body. One application of the device is measuring the strain in a bolt, and other applications such as measuring the thickness of a body, measuring the depth of a flaw in a body, measuring the elongation of a body, and measuring changes in velocity of sound in a body. The body is connected, by means of a CW transducer, to electrical circuit means including a narrow band RF amplifier to form a closed loop feedback marginal oscillator that frequency locks the device to the peak of a mechanical resonance in the body. When the frequency of this peak changes, because of a physical change in the body, the frequency of the oscillator changes. The device includes an automatic frequency resonant peak tracker that produces a voltage that is related to a change in frequency of the oscillator. This voltage is applied to the RF amplifier to change the center of its frequency band to include the frequency of the peak and is a measure of the frequency shift.

Heyman, J. S.↗

Capacitive Trans-Impedance Amplifier Circuit with Charge Injection Compensation

A capacitive trans-impedance amplifier circuit with charge injection compensation is provided. A feedback capacitor is connected between an inverting input port and an output port of an amplifier. A MOS reset switch has source and drain terminals connected between the inverting input and output ports of the amplifier, and a gate terminal controlled by a reset signal. The reset switch is open or inactive during an integration phase, and closed or active to electrically connect the inverting input port and output port of the amplifier during a reset phase. One or more compensation capacitors are provided that are not implemented as gate oxide or MOS capacitors. Each compensation capacitor has a first port connected to a compensation signal that is a static signal or a toggling compensation signal that toggles between two compensation voltage values, and a second port connected to the inverting input port of the amplifier.

Milkov, Mihail M.↗

Ramp-integration technique for capacitance-type blade-tip clearance measurement

The analysis of a proposed new technique for capacitance type blade tip clearance measurement is presented. The capacitance between the blade tip and a mounted capacitance electrode within a guard ring forms one of the feedback elements of a high speed operational amplifier. The differential equation governing the operational amplifier circuit is formulated and solved for two types of inputs to the amplifier - a constant voltage and a ramp. The resultant solutions shows an output that contains a term that is proportional to the derivative of the product of the input voltage and the time constant of the feedback network. The blade tip clearance capacitance is obtained by subtracting the output of a balancing reference channel followed by integration. The proposed sampled data algorithm corrects the environmental effects and varying rotor speeds on-line, making the system suitable for turbine instrumentation. System requirements, block diagrams, and typical application are included.

Sarma, G. R.↗

Ramp-integration technique for capacitance-type blade-tip clearance measurement

The analysis of a proposed new technique for capacitance type blade tip clearance measurement is presented. The capacitance between the blade tip and a mounted capacitance electrode within a guard ring forms one of the feedback elements of a high speed operational amplifier. The differential equation governing the operational amplifier circuit is formulated and solved for two types of inputs to the amplifier - a constant voltage and a ramp. The resultant solution shows an output that contains a term that is proportional to the derivative of the product of the input voltage and the time constant of the feedback network. The blade tip clearance capacitance is obtained by subtracting the output of a balancing reference channel followed by integration. The proposed sampled data algorithm corrects for environmental effects and varying rotor speeds on-line, making the system suitable for turbine instrumentation. System requirements, block diagrams, and a typical application are included.

Sarma, Garimella R.↗

Root Dynamics Mitigate Warm and Dry Biases over the Central United States

The central United States frequently exhibits warm and dry biases in simulations of summertime conditions, a persistent feature that remains unresolved. While previous studies linked these biases to misrepresented surface energy exchanges, the role of belowground processes remains poorly understood. Here, we demonstrate that inadequate representation of root water uptake in land surface models contributes to this bias. Using both offline Noah-MP and coupled WRF-Noah-MP simulations with static and dynamic root water uptake schemes, we show that the inclusion of dynamic root processes reduces 2-m air temperature biases and enhances precipitation, primarily by increasing the rain rate of convective systems. Offline and coupled simulations further reveal that the cooling effects and precipitation increases are amplified through positive land-atmosphere feedback, active only in the coupled model. These findings highlight an important role of root in modulating land-atmosphere interactions and underscore the need to refine root-zone processes to improve regional atmospheric simulations.

Yang, Zhao (ORCID:0000000288027130)↗

Ac-coupled ultrahigh input impedance amplifier

Input impedances of several hundred megohms and input capacitances of less than one picofarad are achieved with a conventional unity gain are buffer amplifier modified by addition of positive feedback. The circuit is stable over a temperature range of 25 to 70 deg C.

Birchenough, A. G.↗

Test results of Spacelab 2 infrared telescope focal plane

The small helium cooled infrared telescope for Spacelab 2 is designed for sensitive mapping of extended, low-surface-brightness celestial sources as well as highly sensitive investigations of the shuttle contamination environment (FPA) for this mission is described as well as the design for a thermally isolated, self-heated J-FET transimpedance amplifier. This amplifier is Johnson noise limited for feedback resistances from less than 10 to the 8th power Omega to greater than 2 x 10 to the 10th power Omega at T = 4.2K. Work on the focal plane array is complete. Performance testing for qualification of the flight hardware is discussed, and results are presented. All infrared data channels are measured to be background limited by the expected level of zodiacal emission.

Young, E. T.↗