Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOW DEFLECTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1959

Preliminary Measurements of the Noise Characteristics of Some Jet-Augmented-Flap Configurations

Experimental noise studies were conducted on model configurations of some proposed jet-augmented flaps to determine their far-field noise characteristics. The tests were conducted using cold-air jets of circular and rectangular exits having equal areas, at pressure ratios corresponding to exit velocities slightly below choking. Results indicated that the addition of a flap to a nozzle may change both its noise radiation pattern and frequency spectrum. Large reductions in the noise radiated in the downward direction are realized when the flow from a long narrow rectangular nozzle as permitted to attach to and flow along a large flap surface. Deflecting or turning the jet flow by means of impingement on the under surfaces increases the noise radiated in all directions and especially in the downward direction for the jet-flap configurations tested. Turning of the flow from nozzles by means of a flap turns the noise pattern approximately an equal amount. The principle of using a jet-flap shield with flow attachment may have some application as a noise suppressor.

Maglieri, Domenic J.↗
NASA NTRS1985

Deflected jet experiments in a turbulent combustor flowfield

Experiments were conducted to characterize the time-mean and turbulent flow field of a deflected turbulent jet in a confining cylindrical crossflow. Jet-to-crossflow velocity ratios of 2, 4, and 6 were investigated, under crossflow inlet swirler vane angles of 0 (swirler removed), 45 and 70 degrees. Smoke, neutrally buoyant helium-filled soap bubbles, and multi-spark flow visualization were employed to highlight interesting features of the deflected jet, as well as the tracjectory and spread pattern of the jet. A six-position single hot-wire technique was used to measure the velocities and turbulent stresses in nonswirling crossflow cases. In these cases, measurements confirmed that the deflected jet is symmetrical about the vertical plan passing through the crossflow axis, and the jet penetration was found to be reduced from that of comparable velocity ratio infinite crossflow cases. In the swirling crossflow cases, the flow visualization techniques enabled gross flow field characterization to be obtained for a range of lateral jet-to-crossflow velocity ratios and a range of inlet swirl strengths in the main flow.

Ferrell, G. B.↗
NASA NTRS1996

Wind tunnel test results of a 1/8-scale fan-in-wing model

A 1/8-scale model of a fan-in-wing concept considered for development by Grumman Aerospace Corporation for the U.S. Army was tested in the Langley 14- by 22-Foot Subsonic Tunnel. Hover testing, which included height above a pressure-instrumented ground plane, angle of pitch, and angle of roll for a range of fan thrust, was conducted in a model preparation area near the tunnel. The air loads and surface pressures on the model were measured for several configurations in the model preparation area and in the tunnel. The major hover configuration change was varying the angles of the vanes attached to the exit of the fans for producing propulsive force. As the model height above the ground was decreased, there was a significant variation of thrust-removed normal force with constant fan speed. The greatest variation was generally for the height-to-fan exit diameter ratio of less than 2.5; the variation was reduced by deflecting fan exit flow outboard with the vanes. In the tunnel angles of pitch and sideslip, height above the tunnel floor, and wind speed were varied for a range of fan thrust and different vane angle configurations. Other configuration features such as flap deflections and tail incidence were evaluated as well. Though the V-tail empennage provided an increase in static longitudinal stability, the total model configuration remained unstable.

Wilson, John C.↗
NASA NTRS2014

Design Environment for Multifidelity and Multidisciplinary Components

One of the greatest challenges when developing propulsion systems is predicting the interacting effects between the fluid loads, thermal loads, and structural deflection. The interactions between technical disciplines often are not fully analyzed, and the analysis in one discipline often uses a simplified representation of other disciplines as an input or boundary condition. For example, the fluid forces in an engine generate static and dynamic rotor deflection, but the forces themselves are dependent on the rotor position and its orbit. It is important to consider the interaction between the physical phenomena where the outcome of each analysis is heavily dependent on the inputs (e.g., changes in flow due to deflection, changes in deflection due to fluid forces). A rigid design process also lacks the flexibility to employ multiple levels of fidelity in the analysis of each of the components. This project developed and validated an innovative design environment that has the flexibility to simultaneously analyze multiple disciplines and multiple components with multiple levels of model fidelity. Using NASA's open-source multidisciplinary design analysis and optimization (OpenMDAO) framework, this multifaceted system will provide substantially superior capabilities to current design tools.

Platt, Michael↗
NASA NTRS1994

The 1992/93 eclipse of 31 Cygni

Extensive new ultraviolet and optical spectra of an atmospheric eclipse define the physical properties throughout the wind and chromosphere of 31 Cyg. These data require mass loss of approximately 3 x 10(exp -8) solar masses/yr in a wind that may merge smoothly into the chromosphere. Considerations of how energy is injected into the wind, however, suggest that the chromosphere and wind are separate structures. Most, if not all, of the velocity structure in metallic lines, which we have heretofore simulated with Doppler widths in the range 15-25 km/s, results from differential expansion of the atmosphere. Electron densities in the inner R(sub star) of the chromosphere are in the range 1.5 x 10(exp 9) - 2 x 10(exp 8)/cu cm, which implies clumping of the gas. The ionization of oxygen and nitrogen is consistent with clumping by factors of 3-30 in the outer chromosphere, roughly the amount required to give enough gas pressure to support the chromosphere. Chromospheric gas in 31 Cyg becomes hotter with increasing height, thus with decreasing optical depth, in a way that seems similar for all the zeta Aur binaries. Excitation temperature for Fe II in 1992/93 rises from about 5000 K at the deepest points sampled to about 12,500 K high in the wind. Strengths of violet Balmer lines give an excitation temperature for hydrogen of 6200-6500 K above a radial mass column density of approximately 0.01 g/sq cm. This amount of excitation implies that Lyman-alpha is thermalized beneath about 4 x 10(exp -3) g/sq cm. The outer atmosphere was symmetrical to within a factor of 2 in 1992/93, although it was clearly variable at this level, and it had similar mass column densities as in 1982. One manifestation of the variability was a flow toward the B star at phases 0.013-0.022 spanning velocities 45-100 km/s. Several lines of evidence point to a complicated and variable ionization in the wind: At large distance from the K star, measured mass column densities are less by up to a factor of 3 than required by a smoothly flowing wind. Also, much of the gas beyond r = 350 solar radii = 1.75 R(sub star) has a negative radial velocity. Radial velocities of the shell lines imply the outer atmosphere rotates in the direction of orbital motion, possibly through the deflection of wind flow lines in this direction.

Eaton, Joel A.↗
NASA NTRS1993

A numerical study of the effect of geometry variation, turbulence models, and dissipation on the flow past control surfaces

The steady 3D viscous flow past the ONERA M6 wing and a slender delta wing-body with trailing edge control surfaces has been computed. A cell-centered finite-volume Navier-Stokes patched zonal method has been used for the numerical simulation. Both diagonalized and LUSGS schemes have been implemented. Besides the standard nonplanar zonal interfacing techniques, a new virtual zone capability has been employed. For code validation, the transonic flow past the ONERA M5 wing is calculated for angles-of-attack of 3.06 deg and 5.06 deg and compared with the available experiments. The wing-body computational results are compared with experimental data for both trailing-edge flaps deflected. The experimental flow conditions are M subinfinity = 0.4, a turbulent Reynolds number of 5.41 million based on a mean aerodynamic chord of 25.959 inches, adiabatic wall, and angles-of-attack varying from 0 deg to 23.85 deg. The computational results are presented for the 23.85 deg angle-of-attack case. The effects of the base flow due to a model sting, the varying second and fourth order numerical dissipation, and the turbulence model are all considered.

Chaussee, Denny S.↗
NASA NTRS1990

A heliospheric vortex street?

This paper presents the hypothesis that the periodic meridional (north-south) flow observed by Voyager 2 in the neighborhood of 20-25 AU were produced by a heliospheric vortex street. The separation of the vortices was approximately 6 AU in the radial direction, and the vortices were carried away from the sun at a speed of approximately 425 km/s. This hypothesis can account for the observed + or - 5 degree deflections in the flow with a period of 25.5 days, and it predicts small amplitude fluctuations in the bulk speed with two maxima per solar rotation, which is consistent with observations in 1986.

Burlaga, L. F.↗
NASA NTRS1994

Midtail plasma flows and the relationship to near-Earth substorm activity: A case study

Recent simulations of magnetotail reconnection have pointed to a link between plasma flows, dipolarization, and the substorm current wedge. In particular, Hesse and Birn (1991) have proposed that earthward jetting of plasma from the reconnection region transports flux into the near-Earth region. At the inner edge of the plasma sheet this flux piles up, producing a dipolarization of the magnetic field. The vorticity produced by the east-west deflection of the flow at the inner edge of the plasma sheet gives rise to field-aligned currents that have region 1 polarity. Thus in this scenario the earthward flow from the reconnection region produces the dipolarization ad the current wedge in a self-consistent fashion. In this study we examine observations made on April 8, 1985 by the Active Magnetospheric Particle Tracer Explorers (AMPTE)/Ion Release Module (IRM), the geosynchronous satellites 1979-053, 1983-019, and 1984-037, and Syowa station, as well as AE. This event is unique because IRM was located near the neutral sheet in the midnight sector for am extended period of time. Ground data show that there was ongoing activity in the IRM local time sector for several hours, beginning at 1800 UT and reaching a crescendo at 2300 UT. This activity was also accompanied by energetic particle variations, including injections, at geosynchronous orbit in the nighttime sector. Significantly, there were no fast flows at the neutral sheet until the great intensification of activity at 2300 UT. At that time, IRM recorded fast eartheard flow simultaneous with a dipolatization of the magetic field. We conclude that while the aforementioned scenario for the creation of the current wedge encounters serious problems explaining the earlier activity, the observations at 2300 UT are consistent with the scenario of Hesse and Birn (1191). On that basis it is argued that the physics of substorms is not exclusively rooted in the development of a global tearing mode. Processes at the inner edge of the cross-tail current that cause a disruption of the current and a consequent dipolarization and current wedge may be unrelated to the formation of a macroscale reconnection region. Thus the global evolution of a substorm is probably a complicated superposition of such processes operating on a very localized scale and a global macroscale process that allows for such things as releasing te energy stored in lobe flux and creation of plasmoids.

Lopez, R. E.↗
NASA NTRS1985

On the use of wall functions as boundary conditions for two-dimensional separated compressible flows

A new and improved wall function method for compressible turbulent flows has been developed and tested. This method is applicable to attached and separated flows, to both high- and low-Reynolds number flows, and to flows with adiabatic and nonadiabatic surfaces. This wall function method has been applied to the Launder-Spalding k-epsilon two-equation model of turbulence. The tests consist of comparisons of calculated and experimental results for: (1) an axisymmetrical transonic shock-wave/boundary-wave interaction flow at low Reynolds number in an adiabatic tube, (2) an axisymmetrical high-Reynolds number transonic flow over a nonadiabatic bump, and (3) a two-dimensional supersonic high-Reynolds number flow on a nonadiabatic deflected flap. Each of these experiments had significant regions of flow separation. The calculations are performed with an implicit algorithm that solves the Reynolds-averaged Navier-Stokes equations. It is shown that the results obtained agree very well with the data for the complex compressible flows tested.

Viegas, J. R.↗
NASA NTRS2016

Longitudinal Aerodynamic Modeling of the Adaptive Compliant Trailing Edge Flaps on a GIII Airplane and Comparisons to Flight Data

A pair of compliant trailing edge flaps was flown on a modified GIII airplane. Prior to flight test, multiple analysis tools of various levels of complexity were used to predict the aerodynamic effects of the flaps. Vortex lattice, full potential flow, and full Navier-Stokes aerodynamic analysis software programs were used for prediction, in addition to another program that used empirical data. After the flight-test series, lift and pitching moment coefficient increments due to the flaps were estimated from flight data and compared to the results of the predictive tools. The predicted lift increments matched flight data well for all predictive tools for small flap deflections. All tools over-predicted lift increments for large flap deflections. The potential flow and Navier-Stokes programs predicted pitching moment coefficient increments better than the other tools.

aerodynamics↗
NASA NTRS1976

Study of liquid jet impingement on screens

A model is presented for an unconfined flow, such as a free jet, impinging on a screen which incorporates the influence of liquid deflection by the screen. The boundary layer blockage coefficient is introduced. This coefficient depends on the screen weave geometry and the jet impingement angle, and essentially accounts for the increase in fluid particle trajectory length through the screen resulting from the flow deflection. Comparisons were made with previous experimental studies to determine empirical values of the blockage coefficient. It is concluded that the new model reliably predicts the bulk flow and penetration characteristics of an impinging liquid jet interacting with a screen.

Dodge, F. T.↗
NASA NTRS1980

Flow visualization study of spanwise blowing applied to the F-4 fighter aircraft configuration

Water tunnel studies were performed to define the changes that occur in vortex flow fields above the wing due to spanwise blowing over the inboard and outboard wing panels and over the trailing-edge flaps. Flow visualization photographs were obtained for angles of attack up to 30 deg and sideslip angles up to 10 deg. The sensitivity of the vortex flows to changes in flap deflection angle, nozzle position, and jet momentum coefficient was determined. Deflection of the leading edge flap delayed flow separation and the formation of the wing vortex to higher angles of attack. Spanwise blowing delayed the breakdown of the wing vortex to farther outboard and to higher angles of attack. Spanwise blowing over the trailing edge flap entrained flow downward, producing a lift increase over a wide range of angles of attack. The sweep angle of the windward wing was effectively reduced in sideslip. This decreased the stability of the wing vortex, and it burst farther inboard. Reduced wing sweep required a higher blowing rate to maintain a stable vortex. A vortex could be stabilized on the outboard wing panel when an outboard blowing nozzle was used. Blowing from both an inboard and an outboard nozzle was found to have a favorable interaction.

Lorincz, D. J.↗
NASA NTRS1993

Ulysses plasma observations in the Jovian magnetosheath

The solar wind plasma experiment aboard the Ulysses spacecraft, including separate ion and electron instruments, measured the plasma properties of the Jovian magnetosheath during the February 1992 encounter with Jupiter. Seven separate magnetosheath intervals were observed, as well as four bow shock crossings and numerous encounters with the magnetopause and its boundary layer. We present an overview of ion and electron bulk parameters and a sampling of distribution shapes for the magnetosheath and adjacent plasma regions. Plasma flows are generally appropriate for slowing and deflection of the solar wind flow about a relatively stationary obstacle, with the notable exception of the first inbound sheath transit, when an expanding magnetosphere resulted in sunward flow just above the magnetopause. The existence of a planetary depletion layer is suggested by trends in plasma density for some magnetopause encounters. The magnetopause boundary layer is characterized by a combination of sheathlike and magnetospheric distributions of both ions and electrons. The ion population in the sheath is observed to include a significant population of suprathermal protons. Electron distributions have a distinctive shape previously observed in the terrestrial magnetosheath, with fluxes parallel to the magnetic field dominating at thermal energies and perpendicular fluxes dominating at higher energies. Trends in electron temperature near the bow shock indicate that shock motion plays an important role in heating the electrons. In general, the plasma characteristics of the Jovian magnetosheath are quite similar to those in its terrestrial counterpart, but the compressible nature of the Jovian magnetosphere accentuates the importance of boundary motions.

Phillips, J. L.↗
NASA NTRSDate not supplied

Active Flow Control Enhanced Aileron of the High-Lift Common Research Model at Takeoff Condition

An experimental investigation was conducted in the NASA Langley 14- by 22-Foot Subsonic Tunnel on the NASA 10% scale High-Lift Common Research Model (CRM-HL) to improve the high-lift aerodynamic performance of the takeoff configuration. Active flow control (AFC) was applied at the aileron hinge line to control flow separation at high aileron deflection angles ( δ a ) to increase lift-to-drag ratio (R/J). Improvements in low speed R/J can increase vehicle payload and/or range resulting in a more efficient vehicle. Aileron deflection angles of 0°, 7.5°, 16°, and 25° were investigated. Flow control was applied to the two largest aileron deflections, which are considered the high-lift (HL) improved takeoff configurations. A companion paper will discuss baseline flow characteristics of the CRM-HL at the three takeoff conditions: reference, nominal, and HL-improved. In this paper, we focus on the aerodynamic improvement obtained when AFC was applied to δ a = 16° relative to the nominal configuration, δ a = 7.5°. Multiple flow control parameters, including actuator type, spacing, and intensity, were investigated to evaluate the efficiency of the actuation system. The different AFC configurations tested were assessed with tuft visualization, steady surface pressure data, and force and moment data. The results indicated that all actuation types and spacings examined led to an increase in lift across the range of angles of attack investigated. Flow separation was mitigated with the injection of momentum at the aileron hinge line. The configurations with the smallest spacing produced the highest improvement in L/D . Steady jet actuation showed higher efficiency but similar aerodynamic performance when compared to the sweeping jet actuators. This work was performed in support of the NASA Advanced Air Transport Technology (AATT) Project.

High-Lift Common Research Model↗
NASA NTRS2004

SiC-Based Miniature High-Temperature Cantilever Anemometer

The figure depicts a miniature cantilever-type anemometer that has been developed as a prototype of compact, relatively nonintrusive anemometers that can function at temperatures up to 600 C and that can be expected to be commercially mass-producible at low cost. The design of this anemometer, and especially the packaging aspect of the design, is intended to enable measurement of turbulence in the high-temperature, high-vibration environment of a turbine engine or in any similar environment. The main structural components of the anemometer include a single-crystal SiC cantilever and two polycrystalline SiC clamping plates, all made from chemical-vapor-deposited silicon carbide. Fabrication of these components from the same basic material eliminates thermal-expansion mismatch, which has introduced spurious thermomechanical stresses in cantilever-type anemometers of prior design. The clamping plates are heavily oxidized to improve electrical insulation at high temperature. A cavity that serves as a receptacle for the clamped end of the cantilever is etched into one end of one clamping plate. Trenches that collectively constitute a socket for a multipin electrical plug (for connection to external electronic circuitry) are etched into the opposite end of this clamping plate. Metal strips for electrical contact are deposited on one face of the other clamping plate. Piezoresistive single-crystal SiC thin-film strain gauges are etched in the n-type SiC epilayer in a Wheatstone-bridge configuration. Metal contact pads on the cantilever that extend into the clamping-receptacle area, are obtained by deposition and patterning using standard semiconductor photolithography and etching methods. The cantilever and the two clamping plates are assembled into a sandwich structure that is then clamped in a stainless-steel housing. The Wheatstone- bridge carrying SiC cantilever with the metal contact pads on the piezoresistors is slid into the receptacle in the bottom clamping plate. The top clamping plate is brought into contact with the bottom plate so that the narrow section of the metal strips on the top clamp plate aligns with the metal contact pads on the cantilever. When the parts are clamped together, the metal strips provide electrical connections between the Wheatstone-bridge contact points and the sides the trenches that constitute the socket for the multipin electrical plug. Hence, to connect the Wheatstone bridge to external circuitry for processing of the anemometer readout, one need only insert the plug in the socket. In operation, the cantilever end of the stainless-steel housing is mounted flush with an engine wall and the unclamped portion of the cantilever is exposed into the flow. The cantilever is deflected in direct proportion to the force induced by component of flow parallel to the engine wall and perpendicular to the broad exposed face of the cantilever. The maximum strain on the cantilever occurs at the clamped edge and is measured by the piezoresistors, which are located there. The corresponding changes in resistance manifest themselves in the output of the Wheatstone bridge.

Okojie, Robert S.↗
DOE OSTI2024

Impacts of Irradiation Structural Behavior on Thermal Hydraulics Safety Analysis to Support MURR LEU Conversion

The University of Missouri Research Reactor (MURR) located in Columbia, Missouri is one of six U.S. High Performance Research Reactors (USHPRR), including one critical facility, that is actively collaborating with U. S. Department of Energy (DOE) National Nuclear Security Administration (NNSA) Material Management and Minimization (M3) Office of Reactor Conversion and Uranium Supply to convert from the use of highly enriched uranium (HEU; ≥20 wt% U-235) to low-enriched uranium (LEU; <20 wt% U-235) fuel. A new type of very high-density LEU fuel based on an alloy of uranium and 10 wt% molybdenum (U-10Mo) is expected to allow the conversion to LEU of MURR, as well as four other USHPRR. MURR has been working with the Reactor Conversion Pillar at Argonne to perform fuel element design and fuel cycle performance analyses, steady-state thermal hydraulics safety analysis, and accident safety analyses in preparation for the conversion of MURR and to support a preliminary safety analysis report for conversion to LEU fuels. Subsequent analyses have also been performed, including transition cycles where all-fresh LEU fuel elements are introduced upon conversion and progressing through reactor operations the core is brought to equilibrium. Thermal hydraulics safety analyses performed as part of the above have employed an assumption on channel gap reduction due to burnup-related phenomena including fuel swelling, irradiation creep, and oxide layer buildup. Recently, a series of structural analyses have been performed on the MURR LEU fuel plates and an element due to significant differences between the plate and element designs of the MURR HEU and LEU fuels. In addition, NUREG-1537 indicates that structural phenomena are to be evaluated. Two separate types of structural analyses were performed for the MURR LEU fuel element: fluid-structure interaction (FSI) and irradiation thermo-mechanical. The FSI analysis evaluated the effects of hydraulic forces on the MURR LEU fuel element to quantify the flow-induced plate deflection, and a minimal impact to the channel gap thickness was predicted under prototypic and bounding conditions. The irradiation thermo-mechanical analysis evaluated the effects of fuel swelling, irradiation creep, and thermal expansion for the MURR LEU plates and the element for prototypic thermal and irradiation conditions based on a high-fidelity approach multiphysics approach. Overall, this thermo-mechanical analysis predicts smaller gap thickness changes in previously limiting regions. Larger changes are predicted in the middle of channels, and for end channels where power density is not typically a maximum. An additional thermo-mechanical analysis was performed for the outermost HEU fuel plate, which showed a similar magnitude of deflection as the outermost LEU plate. Due to substantial differences between the channel gap reductions assumed for the previous safety analyses and those predicted by the irradiation thermo-mechanical analysis, a need to evaluate their impact on the thermal hydraulics safety analyses arose. This report presents the results from the steady-state safety analyses for normal operation as well as the accident analyses for the two most limiting accident scenarios.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1972

Space shuttle: Experimental investigations for base drag reduction on a 0.015 scale model MSFS proposed space shuttle booster at Mach numbers from 0.40 to 1.10

A 0.015-scale model of a modified version of the MDAC space shuttle booster was tested to obtain force, static stability, and control effectiveness data. The objective of this test was the reduction of cruise (M = 0.4) base drag by the use of base flaps, base vents, elevon deflection and base flow from a plenum mounted forward of the base heat shield. Transonic data were also obtained to determine the aerodynamic characteristics of the new base shape. Six component aerodynamic force and moment data were recorded over an angle of attack range from 4 deg to 20 deg at 0 deg sideslip and over a sideslip range from -6 deg to 6 deg at 0 deg, 6 deg and 15 deg angle of attack. Mach number varied from 0.4 to 1.10 at a constant R of 2 million per unit length.

Bradley, D.↗