Search NASA⌕ Search

SEARCH · Search NASA

Results for “FRACTURE MECHANICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Deformation and fracture characteristics of zirconium plate produced via ultrasonic additive manufacturing

Abstract The microstructural evolution, deformation modes, and fracture mechanisms of zirconium plate produced using ultrasonic additive manufacturing (UAM) are presented. In addition to conventional tensile testing techniques, digital image correlation captured highly variable strain accumulation in specimens loaded perpendicular or parallel to the build height (Z). When tested in parallel to Z, delamination at prior foil/foil interfaces creates strain localization noticeable in strain rate maps, whereas specimens loaded perpendicular to Z illustrate conventional strain hardening until necking accelerates delamination. Although bond strengths are statistically and spatially variable, in situ electron backscattering diffraction tests illustrate the ability for grains near interfaces to accommodate strain with twinning and slip modes consistent with conventionally produced zirconium alloys. Finally, mixtures of ductile and delamination-induced fracture highlight the interface-driven failure modes of UAM zirconium plate in the as-built condition. Graphic abstract

36 MATERIALS SCIENCE↗
DOE OSTI2022

Graphene coating on silicon anodes enabled by thermal surface modification for high-energy lithium-ion batteries

Silicon is a high-energy density anode material for lithium-ion batteries, but it possesses shortcomings such as poor electronic conductivity, interfacial instability and mechanical fracturing that hinder its battery cycling. Carbon coating has been an important strategy for stabilizing silicon anodes, but the effects of the silicon surface properties on carbon coating morphology and the consequent silicon cycling stability have not been clearly elucidated. Herein, we find that thermal oxidation of the silicon anodes followed by chemical vapor deposition of carbonaceous precursors leads to a well-ordered graphene coating, whereas disordered graphite coating is formed on the native silicon surface. Graphene-coated silicon exhibits superior cycling performance, retaining a discharge capacity of ~1300 mAh g -1 after 300 cycles, whereas the disordered graphite-coated silicon suffers continuous degradation, retaining only~600 mAh g -1 after 300 cycles. Cryogenic electron microscopy reveals the mechanism behind the difference in cycling stabilities; graphene coated silicon is able to withstand the large mechanical strains induced during extended cycling, whereas disordered graphite coating is ruptured, exposing silicon surfaces to the electrolyte, leading to extensive buildup of SEI and poor cycling performance. Characterization of the silicon surface reveals that thermal treatment yields an oxygen-rich surface layer, which is hypothesized to play a decisive role in dictating the carbon coating. This work highlights the effect of silicon surface properties on carbon coating microstructure, and presents thermal treatment as a facile avenue to attain graphene coating on silicon anodes.

25 ENERGY STORAGE↗
DOE OSTI2021

Verification of Coupled Hydraulic Fracturing Simulators Using Laboratory-Scale Experiments

In this work, we aim to verify the predictions of the numerical simulators, which are used for designing field-scale hydraulic stimulation experiments. Although a strong theoretical understanding of this process has been gained over the past few decades, numerical predictions of fracture propagation in low-permeability rocks still remains a challenge. Against this background, we performed controlled laboratory-scale hydraulic fracturing experiments in granite samples, which not only provides high-quality experimental data but also a well-characterized experimental set-up. Using the experimental pressure responses and the final fracture sizes as benchmark, we compared the numerical predictions of two coupled hydraulic fracturing simulators—CSMP and GEOS. Both the simulators reproduced the experimental pressure behavior by implementing the physics of Linear Elastic Fracture Mechanics (LEFM) and lubrication theory within a reasonable degree of accuracy. The simulation results indicate that even in the very low-porosity (1–2 %) and low-permeability (10 -18 m 2 - 10 -19 m 2 ) crystalline rocks, which are usually the target of EGS, fluid-loss into the matrix and unsaturated flow impacts the formation breakdown pressure and the post-breakdown pressure trends. Therefore, underestimation of such parameters in numerical modeling can lead to significant underestimation of breakdown pressure. The simulation results also indicate the importance of implementing wellbore solvers for considering the effect of system compressibility and pressure drop due to friction in the injection line. The varying injection rate as a result of decompression at the instant of fracture initiation affects the fracture size, while the entry friction at the connection between the well and the initial notch may cause an increase in the measured breakdown pressure.

15 GEOTHERMAL ENERGY↗
DOE OSTI2023

An Innovative Insight into Performance Degradation of NCM111 Cathode Induced by Suspension of Operation

The lifespan of lithium-ion batteries varies enormously from fundamental study to practical applications. This big difference has been typically ascribed to the high degree of uncertainty in unpredictable and complicated operation conditions in real-life applications. Here, in this paper, we report that the pause of the charging–discharging process, which is frequently operated in practice but rarely studied in academics, is an important reason for the performance degradation of the NCM111 cathode. It is found that the pause during cycling could trigger a remarkable drop in capacity, giving rise to ~30% more capacity decay compared with the continuously cycled sample. In situ synchrotron X-ray diffraction analysis reveals that the harmful H1–H2 phase transition, which typically appears in the initial cycle but disappears in subsequent cycles, is reactivated by the pausing process. The anisotropic lattice strains that occur during the H1–H2 transition result in mechanical fractures that terminate with an inert NiO-type rock-salt phase on the surface of particles. The present study indicates that the discontinuous usage of rechargeable batteries is also a key factor for cycle life, which might provide a distinct perspective on the performance decay in practical applications.

25 ENERGY STORAGE↗
DOE OSTI2025

Impact of post-irradiation annealing on mechanical performance of irradiated 718 alloy

Here, the effect of post-irradiation annealing on solution-annealed 718 alloy was investigated using advanced mechanical testing, fractography, scanning electron microscopy, and transmission electron microscopy. Specimens were extracted from a proton beam window operated at the Spallation Neutron Source, irradiated with 940 MeV protons to a maximum dose of approximately 9.7 displacements per atom (dpa) at a calculated temperature not exceeding 110 °C while in service. Helium and hydrogen concentrations reached about 1700 and 6900 atomic parts per million (appm), respectively. Despite irradiation and high tensile strength (yield stress over 1 GPa), the material exhibited significant ductility. Annealing at 500 °C, 700 °C, and 900 °C for 30 min resulted in an appreciable decrease in yield strength and an increase in ductility for annealing treatments at 500 °C and 900 °C relative to the strength and ductility of the as-irradiated material. The presence of helium and hydrogen led to cavity formation and cleavage-like brittle features on fractured surfaces; however, high-magnification imaging revealed the presence of small-scale ductile dimples, indicating that the fracture mechanism remained mixed. The annealed specimens retained total elongation levels of 14–33 %, and there was no sudden drop in ductility after heat treatments. The ductility level in the irradiated and annealed material is notable despite the presence of helium and hydrogen.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A phase-field model of quasi-brittle fracture for pressurized cracks: Application to UO 2 high-burnup microstructure fragmentation

Here, in this paper, we present a phase-field model of quasi-brittle fracture with pressurized cracks, with dedicated applications for polycrystalline materials. The model is formulated as a minimization problem within the variational framework. The external work done by pressure on the crack surfaces is included in the objective function. Several careful modeling choices lead to a regularization-length-independent critical strength. The model is constructed to give a softening response with an underlying linear traction-separation law. The pressure-dependent softening response and the regularization of the prescribed pressure are demonstrated with a (quasi) one-dimensional numerical analysis. In a two-dimensional numerical analysis under plane strain assumptions, the critical stress corresponding to crack propagation (as predicted by our quasi-brittle fracture model) is compared with linear elastic fracture mechanics (LEFM) analytical solutions. Our model is further utilized to simulate fission-gas-induced fragmentation of the UO 2 high-burnup structure (HBS). Simulation results show that pressurized bubbles can cause crack nucleation and propagation, and that the bubble size and the surrounding external pressure affect the critical pressure corresponding to crack nucleation. Simulations of a partial HBS at different recrystallization stages show that different grain structures (due to recrystallization) also influence crack paths and fragmentation morphology.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Electrochemically induced fracture in LLZO: How the interplay between flaw density and electrostatic potential affects operability

Fracture and short circuit in the Li 7 La 3 Zr 2 O 12 (LLZO) solid electrolyte are two key issues that prevent its adoption in battery cells. In this paper, we utilize phase-field simulations that couple electrochemistry and fracture to evaluate the maximum electric potential that LLZO electrolytes can support as a function of crack density. In the case of a single crack, we find that the applied potential at the onset of crack propagation exhibits inverse square root scaling with respect to crack length, analogous to classical fracture mechanics. Here, we further find that the short-circuit potential scales linearly with crack length. In the realistic case where the solid electrolyte contains multiple cracks, we reveal that failure fits the Weibull model. The failure distributions shift to favor failure at lower overpotentials as areal crack density increases. Furthermore, when flawless interfacial buffers are placed between the applied potential and the bulk of the electrolyte, failure is mitigated. When constant currents are applied, current focuses in near-surface flaws, leading to crack propagation and short circuit. We find that buffered samples sustain larger currents without reaching unstable overpotentials and without failing. Our findings suggest several mitigation strategies for improving the ability of LLZO to support larger currents and improve operability.

25 ENERGY STORAGE↗
DOE OSTI2025

Interaction between dissolution and precipitation during olivine carbonation: Implications for CO 2 mineralization

Large-scale carbonation of olivine is considered a promising approach for in situ mineral carbonation, offering a permanent and stable method for CO 2 storage. A critical aspect of this process is understanding how dissolution and precipitation interact, as this could drive fracturing and enhance further reactions. In this study, we conducted carbonation experiments on olivine using CO 2 -saturated aqueous solutions of NaHCO 3 and NaCl. Two experimental setups were used: one representing an open geochemical system and the other a closed system, corresponding to reaction-limited and flow-limited scenarios, respectively. Further, post-reaction textural analysis using scanning electron microscopy (SEM) revealed surface coatings of reaction products in the closed system, while etch pits and etch channels were prevalent in the open system. Although no direct evidence of reaction-driven fracturing was observed, etch pits and etch channels may serve as initiation points for subcritical crack formation and growth, potentially maintaining permeability and exposing new unreacted surfaces. Using linear elastic fracture mechanics (LEFM) model, we estimate that microcracks could propagate under a pressure of 0.1 GPa if reaction products accumulate within the etch pits. Our findings offer new insights into the mechanisms governing olivine carbonation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

On the bulk compaction of brittle granular materials, Part II: Representing interparticle comminution by K COMP

An applied and empirical compaction fracture resistance parameter, K COMP , was developed to represent the compression-induced interparticle-comminution response of granular brittle materials (e.g., ceramic or glass particles). The development of K COMP is an outcome from Part I of this three-paper series. The K COMP represents a continuum response of compaction fracture resistance and was adapted from established Griffith linear elastic fracture mechanics theory. From that, the K COMP relates macroscopically applied compressive stress to a corresponding inverse-square-root representative particle size, where the latter is estimated from an entire particle size distribution or specific surface area measurement. In conclusion, the K COMP value was not constant over a wide range of stresses for all examined brittle granular materials, and this is indicative of a change in the dominant mode of permanent deformation at higher compaction stresses.

brittle↗
DOE OSTI2021

Characteristics of Premature Creep Failure in Over-tempered Base Metal of Grade 91 Steel Weldment

Characteristics of premature creep failure in the over-tempered base metal (OT-BM) of a Grade 91 steel weldment are investigated with specially designed creep experiments and advanced microstructure characterization. In situ digital image correlation (DIC) strain measurements reveal that local creep strain as high as 100% accumulated in the OT-BM, compared with only 10% nominal strain over the gauge length. The creep strain rate in the OT-BM is identical to that in the intercritical heat-affected zone and fine-grained heat-affected zone at the secondary creep stage and early tertiary stage, but faster at the late tertiary stage. Microstructural analysis shows that highly recovered microstructure in the OT-BM leads to the lowest hardness, the largest grain size, the lowest fraction of coincidence site lattice boundaries, and the lowest localized strain energy. Dislocation creep and transgranular creep fracture are the dominant deformation and fracture mechanisms in the OT-BM under the current creep testing condition of a low temperature (550 °C) and a high stress (215 MPa).

42 ENGINEERING↗
DOE OSTI2026

Latent space dynamics identification for interface tracking with application to shock-induced pore collapse

Capturing sharp, evolving interfaces remains a central challenge in reduced-order modeling, especially when data is limited and the system exhibits localized nonlinearities or discontinuities. Here, we propose LaSDI-IT (Latent Space Dynamics Identification for Interface Tracking), a data-driven framework that combines low-dimensional latent dynamics learning with explicit interface-aware encoding to enable accurate and efficient modeling of physical systems involving moving material boundaries. At the core of LaSDI-IT is a revised autoencoder architecture that jointly reconstructs the physical field and an indicator function representing material regions or phases, allowing the model to track complex interface evolution without requiring detailed physical models or mesh adaptation. The latent dynamics are learned through linear regression in the encoded space and generalized across parameter regimes using Gaussian process interpolation with greedy sampling. We demonstrate LaSDI-IT on the problem of shock-induced pore collapse in high explosives, a process characterized by sharp temperature gradients and dynamically deforming pore geometries. The method achieves relative prediction errors below 9% across the parameter space, accurately recovers key quantities of interest such as pore area and hot spot formation, and matches the performance of dense training with only half the data. This latent dynamics prediction was 10 6 times faster than the conventional high-fidelity simulation, proving its utility for multi-query applications. These results highlight LaSDI-IT as a general, data-efficient framework for modeling discontinuity-rich systems in computational physics, with potential applications in multiphase flows, fracture mechanics, and phase change problems.

Gaussian process↗
DOE OSTI2023

A constitutive framework for rocks undergoing solid dissolution

Here, we formulate a time-dependent damage theory for rocks subjected to mechanical deformation and solid dissolution. The constitutive description is inspired by the transition state theory, which states that the rate of dissolution is a function of the reactive surface area measured through the crack density in the volume. We use a gradient-enhanced damage framework in which damage depends on the deformation of the material as well as on the amount of solid mass dissolved over time. The gradient-enhanced formulation is characterized by a three-field variational formulation with the solid displacement, nonlocal equivalent strain, and nonlocal rate of solid dissolution as the basic state variables. Traditionally, time-independent damage theories have only allowed damage to increase with increasing external load. In the proposed framework, the degree of damage may increase due to solid dissolution even when the external load is held fixed. In this way, solid dissolution is viewed as a process that is responsible for bringing about rate-dependent effects such as creep and stress-relaxation, which are two common features of geomaterial behavior.

42 ENGINEERING↗
DOE OSTI2025

Investigating Grain Structure and Microcracking in SiCf-SiCm Composites Using 4D-STEM

Silicon carbide (SiC) fiber-reinforced SiC matrix composites (SiCf-SiCm) are promising materials for accident-tolerant fuel (ATF) cladding in light water reactors. This paper, using four-dimensional scanning transmission electron microscopy (4D-STEM), studied the microstructure of SiCf-SiCm at nanoscale and provided grain statistics at the CVI/fiber region. Here, the results reveal that CVI region mainly contain irregular sub-micron grains (115 nm to 1800 nm) with a preferred orientation, while the fiber region has nano equiaxed grains (21 nm to 78 nm) with random orientations. Centered dark field imaging over the fiber regions verified the grain size measurement by 4D-STEM. Through 4D-STEM virtual dark field imaging and orientation mapping, intragranular propagation was identified as the fracture mechanism for a microcrack observed within the CVI region. The amorphous pyrolytic carbon layer was also shown to effectively arrest the microcrack.

4D-STEM↗
DOE OSTI2025

Effect of alloying on intrinsic ductility in WTaCrV high entropy alloys

Tungsten (W) exhibits desirable properties for extreme applications, such as the divertor in magnetic fusion reactors, but its practicality remains limited due to poor formability and insufficient irradiation resistance. In this work, we study the intrinsic ductility of body-centered cubic WTaCrV based high entropy alloys (HEAs), which are known to exhibit excellent irradiation resistance. The ductility evaluations are carried out using a criterion based on the competition between the critical stress intensity factors for emission (K Ie ) and cleavage (K Ic ) in the {110} slip planes and {110} crack planes, which are evaluated within the linear elastic fracture mechanics framework and computed using density functional theory. The results suggest that increasing the alloying concentrations of V and reducing the concentrations of W can significantly improve the ductility in these HEAs. The elastic anisotropy for these HEAs is analyzed using the Zener anisotropy ratio and its correlation with the concentration of W in the alloys is studied. Results indicate that these alloys tend to be fairly isotropic independently from the concentration of W in them. The computed data for the elastic constants of these HEAs is also compared against available experimental data. The results are in good agreement, validating the robustness and accuracy of the computational methods. Multiple phenomenological ductility metrics were also computed and analyzed against the analytical model. Some metrics, mainly the surrogate D parameter, show a good correlation with the Rice model. The potential of these empirical metrics to serve as surrogate screening models for optimizing the compositional space is also discussed.

Anisotropy↗
DOE OSTI2021

Exemption of lattice collapse in Ni–MnO 2 birnessite regulated by the structural water mobility

Lattice collapse and associated mechanical fracture frequently occur in Li-intercalated metal oxide cathodes at the deep charge state upon Li-ion removal, governed by chemical compositions and the resulting electron density of the oxygen atoms. However, similar lattice collapse for metal oxide electrodes in aqueous storage and its mitigation have not been well studied. In this work, we reported the lattice collapse of MnO 2 layered birnessite during the aqueous de-sodiation process at high voltage due to the structural water motion, as evidenced by in situ XRD. Unlike non-aqueous Li-intercalated electrodes, Ni-dopants mitigated the lattice collapse of birnessite at deep charge states. Moreover, density functional theory (DFT) calculations showed that Ni doping induces charge depletion of lattice oxygen due to its higher electronegativity than Mn. This charge reduction, in turn, yields a significant decrease in electrostatic repulsion between the oxygens belonging to lattice and structural water. Classical molecular dynamics simulations based on atomic charges obtained from DFT elucidate that Ni-doping facilitates immobilization of structural water in (Ni)MnO 2 and prevents lattice collapse upon Na-ion removal. (Ni)MnO 2 exempted from lattice collapse shows an improved storage capacity relative to MnO 2 while maintaining similar cycling stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Measuring the density, viscosity, and surface tension of molten titanates using electrostatic levitation in microgravity

Rare earth and barium titanates are useful as ferroelectric, dielectric, and optical materials. Measurements of their thermophysical properties in the liquid state can help guide melt processing technologies for their manufacture and advance understanding of fragile liquids' behavior and glass formation. Here, we report the density, thermal expansion, viscosity, and surface tension of molten BaTi 2 O 5 , BaTi 4 O 9 , and 83TiO 2 -17RE 2 O 3 (RE = La or Nd). Measurements were made using electrostatic levitation and droplet oscillation techniques in microgravity, which provide access to quiescent liquid droplets and deep supercooling of 510–815 K below the equilibrium melting points. Densities were measured over 900–2400 K. Viscosities were similar for all four compositions, increasing from ~10 mPa s near 2100 K to ~30 mPa s near 1750 K. Surface tensions were 450–490 dyn cm -1 for the rare earth titanates and 383–395 dyn cm -1 for the barium titanates; surface tensions of all compositions had small or negligible temperature dependence over 1700–2200 K. In conclusion, for solids recovered after melt quenching, x-ray microtomography revealed the fracture mechanics in crystalline products and minimal internal porosity in glass products, likely arising from entrapped gas bubbles. Internal microstructures were generally similar for products processed either in microgravity or in a terrestrial aerodynamic levitator.

42 ENGINEERING↗
DOE OSTI2022

Surface coating by mechanofusion modulates bulk charging pathways and battery performance of Ni-rich layered cathodes

Ni-rich layered oxides as high-capacity battery cathodes suffer from degradation at high voltages. Here, we utilize a dry surface modification method, mechanofusion (MF), to achieve enhanced battery stability. The simplicity, high yield, and flexibility make it cost-effective and highly attractive for processing at the industrial scale. The underlying mechanisms responsible for performance improvement are unveiled by a systematic study combining multiple probes, e.g., 3D nano-tomography, spectroscopic imaging, in situ synchrotron diffraction, and finite element analysis (FEA). MF affects the bulk crystallography by introducing partially disordered structure, microstrain, and local lattice variation. Furthermore, the crack initiation and propagation pattern during delithiation are regulated and the overall mechanical fracture is reduced after such surface coating. We validate that MF can alter the bulk charging pathways. Such a synergic effect between surface modification and bulk charge distribution is fundamentally important for designing next-generation battery cathode materials.

25 ENERGY STORAGE↗
DOE OSTI2021

Signature of transition to supershear rupture speed in the coseismic off-fault damage zone

Most earthquake ruptures propagate at speeds below the shear wave velocity within the crust, but in some rare cases, ruptures reach supershear speeds. The physics underlying the transition of natural subshear earthquakes to supershear ones is currently not fully understood. Most observational studies of supershear earthquakes have focused on determining which fault segments sustain fully grown supershear ruptures. Experimentally cross-validated numerical models have identified some of the key ingredients required to trigger a transition to supershear speed. However, the conditions for such a transition in nature are still unclear, including the precise location of this transition. In this work, we provide theoretical and numerical insights to identify the precise location of such a transition in nature. We use fracture mechanics arguments with multiple numerical models to identify the signature of supershear transition in coseismic off-fault damage. Furthermore, we then cross-validate this signature with high-resolution observations of fault zone width and early aftershock distributions. We confirm that the location of the transition from subshear to supershear speed is characterized by a decrease in the width of the coseismic off-fault damage zone. We thus help refine the precise location of such a transition for natural supershear earthquakes.

42 ENGINEERING↗