Search NASA⌕ Search

SEARCH · Search NASA

Results for “FREE FLIGHT TESTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Application of Wind Tunnel Free-Flight Technique for Wake Vortex Encounters

A wind tunnel investigation was conducted in the Langley 30- by 60-Foot Tunnel to assess the free-flight test technique as a tool in research on wake vortex encounters. A typical 17.5-percent scale business-class jet airplane model was flown behind a stationary wing mounted in the forward portion of the wind tunnel test section. The span ratio (model span-generating wingspan) was 0.75. The wing angle of attack could be adjusted to produce a vortex of desired strength. The test airplane model was successfully flown in the vortex and through the vortex for a range of vortex strengths. Data obtained included the model airplane body axis accelerations, angular rates, attitudes, and control positions as a function of vortex strength and relative position. Pilot comments and video records were also recorded during the vortex encounters.

Brandon, Jay M.↗
NASA NTRS1961

Stability and Control Characteristics of a Model of an Aerial Vehicle Supported by Four Ducted Fans

The stability and control characteristics of a simple, lightly loaded model approximately one-third the size of a full-scale vehicle have been investigated by a series of free-flight tests. The model is representative of a type of vertically rising aircraft which would utilize four ducted fans as its sole source of lift and propulsion. The ducts were arranged in a rectangular pattern and were fixed to the airframe so that their axes of revolution were vertical for hovering flight. Control moments were provided by remotely controlled compressed-air jets at the sides and ends of the model. In hovering, the model in its original configuration exhibited divergent oscillations about both the roll and pitch axes. Because these oscillations were of a rather short period., the model was very difficult to control by the use of remote controls only. The model could be completely stabilized by the addition of a sufficient amount of artificial damping. The pitching oscillation was made easier to control by increasing the distance between the forward and rearward pairs of ducts. In forward flight, with the model in its original configuration, the top speed was limited by the development of an uncontrollable pitch-up. Large forward tilt angles were required for trim at the highest speeds attained. With the model rotated so that the shorter axis became the longitudinal axis, the pitch trim problem was found to be less than with the longer axis as the longitudinal axis. The installation of a system of vanes in the slipstream of the forward ducts reduced the tilt angle but increased the power required.

Parlett, Lysle P.↗
NASA NTRS1961

Supersonic Free-Flight Measurements of Heat Transfer and Transition on a 10 degree Cone having a Low Temperature Ratio

Heat-transfer coefficients in the form of Stanton number and boundary-layer transition data were obtained from a free-flight test of a 100-inch-long 10 deg. total-angle cone with a 1/16-inch tip radius which penetrated deep into the region of infinite stability of laminar boundary layer over a range of wall-to-local-stream temperature radius and for local Mach numbers from 1.8 to 3.5. Experimental heat-transfer coefficients, obtained at Reynolds numbers up to 160 x 10(exp 6), were in general somewhat higher than theoretical values. A maximum Reynolds number of transition of only 33 x 10(exp 6) was obtained. Contrary to theoretical and some other experimental investigations, the transition Reynolds number initially increased while the wall temperature ratio increased at relatively constant Mach number. Further increases in wall temperature ratio were accompanied by a decrease in transition Reynolds number. Increasing transition Reynolds number with increasing Mach number was also indicated at a relatively constant wall temperature ratio.

Merlet, Charles F.↗
NASA NTRS1955

Qualitative Results from a Flight Investigation to Determine Aileron Effectiveness of Two Rocket-Propelled 1/20-Scale Models of the MX -76 Missile

Free-flight tests of two rocket-propelled l/20-scale models of the Bell MX-776 missile have been conducted to obtain measurements of the aileron deflection required to counteract the induced rolling moments caused by combined angles of attack and sideslip and thus to determine whether the ailerons provided were capable of controlling the model at the attitudes produced by the test conditions. Inability to obtain reasonably steady-state conditions and superimposed high-frequency oscillations in the data precluded any detailed analysis of the results obtained from the tests. For these reasons, the data presented are limited largely to qualitative results.

Stevens, Joseph E.↗
NASA NTRS1950

The Zero-Lift Drag of Several Configurations of the XAAM-N-2 Pilotless Aircraft. TED No. NACA DE332

Free-flight tests have been made to determine the zero-lift drag of several configurations of the XAAM-N-2 pilotless aircraft. Base-pressure measurements were also obtained for some of the configurations. The results show that increasing the wing-thickness ratio from 4 to 6 percent increased the wing drag by about 100 percent at M = 1.3 and by about 30 percent at M = 1.8. Increasing the nose fineness ratio from 5.00 to 6.25 reduced the drag coefficient of the wingless models a maximum of about 0.030 (10 percent) at M = 2.0. A corresponding change in nose shape for the winged models decreased the drag coefficient by about 0.05 in the Mach number range from 1.1 to 1.4; at Mach numbers greater than 1.6 no measurable reduction in drag coefficient was obtained. The drag of the present Sparrow fuselage is less than that of a parabolic fuselage which could contain the same equipment.

Hall, James R.↗
NASA NTRS2011

Overview of Orion Crew Module and Launch Abort Vehicle Dynamic Stability

With the retirement of the Space Shuttle, NASA is designing a new spacecraft, called Orion, to fly astronauts to low earth orbit and beyond. Characterization of the dynamic stability of the Orion spacecraft is important for the design of the spacecraft and trajectory construction. Dynamic stability affects the stability and control of the Orion Crew Module during re-entry, especially below Mach = 2.0 and including flight under the drogues. The Launch Abort Vehicle is affected by dynamic stability as well, especially during the re-orientation and heatshield forward segments of the flight. The dynamic stability was assessed using the forced oscillation technique, free-to-oscillate, ballistic range, and sub-scale free-flight tests. All of the test techniques demonstrated that in heatshield-forward flight the Crew Module and Launch Abort Vehicle are dynamically unstable in a significant portion of their flight trajectory. This paper will provide a brief overview of the Orion dynamic aero program and a high-level summary of the dynamic stability characteristics of the Orion spacecraft.

D. Bruce Owens↗
NASA NTRS2016

Damping Effects of Drogue Parachutes on Orion Crew Module Dynamics

Because simulations of the Orion Crew Module (CM) dynamics with drogue parachutes deployed were under-predicting the amount of damping seen in free-flight tests, an attach-point damping model was applied to the Orion system. A key hypothesis in this model is that the drogue parachutes' net load vector aligns with the CM drogue attachment point velocity vector. This assumption seems reasonable and has historically produced good results, but has never been experimentally verified. The wake of the CM influences the drogue parachutes, which makes performance predictions of the parachutes difficult. Many of these effects are not currently modeled in the simulations. A forced oscillation test of the CM with parachutes was conducted in the NASA LaRC 20-Ft Vertical Spin Tunnel (VST) to gather additional data to validate and refine the attach-point damping model. A second loads balance was added to the original Orion VST model to measure the drogue parachute loads independently of the CM. The objective of the test was to identify the contribution of the drogues to CM damping and provide additional information to quantify wake effects and the interactions between the CM and parachutes. The drogue parachute force vector was shown to be highly dependent on the CM wake characteristics. Based on these wind tunnel test data, the attach-point damping model was determined to be a sufficient approximation of the parachute dynamics in relationship to the CM dynamics for preliminary entry vehicle system design. More wake effects should be included to better model the system.

Aubuchon, Vanessa V.↗
NASA NTRSDate not supplied

Free-Flight Dynamics of an Aeroshell/Drogue Parachute System

A free-flight test of a subscale aeroshell/drogue parachute model was conducted at the NASA Langley Research Center Vertical Spin Tunnel. Mass properties for the aeroshell model were dynamically scaled. This test simulated the flight of the Dragonfly mission spacecraft at an altitude of 18.4 km above the surface of Titan (Saturn’s largest moon). The aeroshell/drogue parachute model exhibited bimodal oscillatory behavior with sustained small- and large-amplitude modes depending on initial conditions. The effects of drogue parachute size, bridle geometry, and bridle rigidity on the aeroshell/drogue parachute dynamics were investigated. The large-amplitude oscillations seemed to be driven by the aeroshell aerodynamics, with bridle leg collapse being an enabling factor. If the bridle legs were rigid, large-amplitude oscillations were not sustainable.

Parachute↗
NASA NTRSDate not supplied

Recent Updates to the Object Reentry Survival Analysis Tool (ORSAT) Version 7.1

The Object Reentry Survival Analysis Tool (ORSAT) code is maintained and used by the NASA Orbital Debris Program Office (ODPO) and has been under continuous development and improvement since the mid-1990s. ORSAT is an object-oriented reentry simulation tool; it models a satellite as a collection of discrete components that follow independent trajectories upon the breakup of the parent object. Version 7.1 of the tool incorporates five years of new thermal and aerodynamic model development, multi-processor parametric study capability, codebase upgrades, and numerous bug-fixes. The thermal demise model was completely rewritten using a forward-time/central-space numerical stencil and incorporating a new pyrolysis model for fiber-reinforced plastic (FRP) materials. New aerodynamic and aeroheating models for hollow cylinders and hollow square prisms were developed using a combination of flow simulations in the direct simulation Monte Carlo (DSMC) Analysis Code (DAC) and Data Parallel Line Relaxation (DPLR) code and free-flight tests in the University of Texas at San Antonio’s Hypersonic Wind Tunnel. The latest version also incorporates a mechanical, strength-based demise model for FRP materials. Minor improvements include an update to the Fortran 2018 codebase; improved integration and speed with the Python-based, multi-core, parametric study tool, AutoORSAT; and fixes for many minor bugs. This new version of ORSAT will enable more accurate reentry risk assessments for modern satellites. This paper presents an overview of these changes and a summary of the verification and validation performed on the final code.

Benton R. Greene↗
NASA NTRSDate not supplied

Recent Updates to the Object Reentry Survival Analysis Tool (ORSAT) Version 7.1

The Object Reentry Survival Analysis Tool (ORSAT) code is maintained and used by the NASA Orbital Debris Program Office (ODPO) and has been under continuous development and improvement since the mid-1990s. ORSAT is an object-oriented reentry simulation tool; it models a satellite as a collection of discrete components that follow independent trajectories upon the breakup of the parent object. Version 7.1 of the tool incorporates five years of new thermal and aerodynamic model development, multi-processor parametric study capability, codebase upgrades, and numerous bug-fixes. The thermal demise model was completely rewritten using a forward-time/central-space numerical stencil and incorporating a new pyrolysis model for fiber-reinforced plastic (FRP) materials. New aerodynamic and aeroheating models for hollow cylinders and hollow square prisms were developed using a combination of flow simulations in the direct simulation Monte Carlo (DSMC) Analysis Code (DAC) and Data Parallel Line Relaxation (DPLR) code and free-flight tests in the University of Texas at San Antonio’s Hypersonic Wind Tunnel. The latest version also incorporates a mechanical, strength-based demise model for FRP materials. Minor improvements include an update to the Fortran 2018 codebase; improved integration and speed with the Python-based, multi-core, parametric study tool, AutoORSAT; and fixes for many minor bugs. This new version of ORSAT will enable more accurate reentry risk assessments for modern satellites. This paper presents an overview of these changes and a summary of the verification and validation performed on the final code.

Benton R. Greene↗
NASA NTRS1972

Stability and control of externally blown flap configurations

The results of wind-tunnel investigations on the stability and control characteristics of externally blown jet-flap configurations are presented. Conventional wind-tunnel tests and free-flight model tests have shown that longitudinal trim and stability can be achieved by a properly located horizontal tail of sufficient size, and that lateral trim in the engine-out condition can be produced by combinations of differential flap, spoiler, and rudder deflection. Free-flight model tests have revealed a lightly damped Dutch roll lateral oscillation, and have shown that the oscillation can be stabilized by use of artificial damping.

Parlett, L. P.↗
NASA NTRS1993

Concept definition study for an extremely large aerophysics range facility

A conceptual design of a very large aeroballistic range is presented, as are its operational characteristics and procedures. The proposed model launcher is a two-stage light-gas gun, having a launch tube diameter of 254 mm, and the capability of accelerating a 14 kg launch mass to 6.1 km/sec. The gun's 91.4 cm diameter piston is driven by pressurized helium. High pressures in the central breech are contained by a multiple disk arrangement. The blast tank and sabot separation tank are described, as are methods for arresting sabot segments. The conceptual design of the range itself includes a 3.3 m diameter test or flight chamber some 330 m in length. Provisions are made for testing of free flight models and tests in which the model is confined by a track system. Methods for model deceleration and recovery are described. Provisions required for future addition of advanced model launchers such as an electromagnetic launcher or ram accelerator are addressed. Siting and safety issues are also addressed.

Swift, Hallock F.↗
NASA NTRS1954

A Free-flight Wind Tunnel for Aerodynamic Testing at Hypersonic Speeds

The supersonic free-flight wind tunnel is a facility at the Ames Laboratory of the NACA in which aerodynamic test models are gun-launched at high speed and directed upstream through the test section of a supersonic wind tunnel. In this way, test Mach numbers up to 10 have been attained and indications are that still higher speeds will be realized. An advantage of this technique is that the air and model temperatures simulate those of flight through the atmosphere. Also the Reynolds numbers are high. Aerodynamic measurements are made from photographic observation of the model flight. Instruments and techniques have been developed for measuring the following aerodynamic properties: drag, initial lift-curve slope, initial pitching-moment-curve slope, center of pressure, skin friction, boundary-layer transition, damping in roll, and aileron effectiveness. (author)

Seiff, Alvin↗
NASA NTRS1972

Summary of directional divergence characteristics of several high performance aircraft configurations

The present paper summarizes the high-angle-of-attack characteristics of a number of high-performance aircraft as determined from model force tests and free-flight model tests and correlates these characteristics with the dynamic directional-stability parameter. This correlation shows that the dynamic directional-stability parameter correlates fairly well with directional divergence. Data are also presented to show the effect of some airframe modifications on the directional divergence potential of the configuration. These results show that leading-edge slates seem to be the most effective airframe modification for reducing or eliminating the directional divergence potential of aircraft with moderately swept wings.

Greer, H. D.↗