SEARCH · Search NASA

Results for “Free Volume”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

DOE OSTI2019

Progress towards a phenomenological picture and theoretical understanding of glassy dynamics and vitrification near interfaces and under nanoconfinement

The nature of alterations to dynamics and vitrification in the nanoscale vicinity of interfaces-commonly referred to as "nanoconfinement" effects on the glass transition-has been an open question for a quarter century. We first analyze experimental and simulation results over the last decade to construct an overall phenomenological picture. Key features include the following: after a metrology- and chemistry-dependent onset, near-interface relaxation times obey a fractional power law decoupling relation with bulk relaxation; relaxation times vary in a double-exponential manner with distance from the interface, with an intrinsic dynamical length scale appearing to saturate at low temperatures; the activation barrier and vitrification temperature T-g approach bulk behavior in a spatially exponential manner; and all these behaviors depend quantitatively on the nature of the interface. We demonstrate that the thickness dependence of film-averaged T-g for individual systems provides a poor basis for discrimination between different theories, and thus we assess their merits based on the above dynamical gradient properties. Entropy-based theories appear to exhibit significant inconsistencies with the phenomenology. Diverse free-volume-motivated theories vary in their agreement with observations, with approaches invoking cooperative motion exhibiting the most promise. The elastically cooperative nonlinear Langevin equation theory appears to capture the largest portion of the phenomenology, although important aspects remain to be addressed. A full theoretical understanding requires improved confrontation with simulations and experiments that probe spatially heterogeneous dynamics within the accessible 1-ps to 1-year time window, minimal use of adjustable parameters, and recognition of the rich quantitative dependence on chemistry and interface. Published under license by AIP Publishing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Mean force kinetic theory applied to self-diffusion in supercritical Lennard-Jones fluids

A new kinetic-theory-based calculation of the self-diffusion coefficient for dense supercritical Lennard-Jones fluids is presented. The mean force kinetic theory, which was recently developed for transport in dense plasmas, is applied for the calculation of diffusion in dense neutral fluids. The calculation only requires the pair distribution function, a quantity that is readily calculable from equilibrium statistical mechanics for many systems, including the Lennard-Jones fluid. The self-diffusion coefficients are compared with calculations from molecular dynamics simulations, and good agreement at high density is demonstrated, even in the vicinity of the solid–fluid coexistence line. A comparison of different kinetic models with molecular dynamics simulations demonstrates that the transport coefficients have important contributions due to particle interaction via a potential of mean force and local correlations, which increase the collision rate. The new calculations compare well to those from free-volume theory and overcome a limitation of this theory that prevents its use in systems that interact via long range monotonic potentials. It is expected that this approach will also apply to other systems, including neutral-plasma and neutral-electrolyte mixtures.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2020

Isotope effects on the high pressure viscosity of liquid water measured by differential dynamic microscopy

In this paper, differential dynamic microscopy is performed in diamond anvil cells to measure the viscosity of water along the 24 °C isotherm to high-pressure by determination of the tracer diffusion coefficient of monodisperse silica spheres of known diameter and application of the Stokes-Einstein-Sutherland equation. This technique allows liquid samples to be compressed to greater pressure prior to freezing than with other viscometry methods. The highest-pressure measurement was made at 1.67 GPa, considerably deeper into the supercompressed regime than previously reported. The effect of isotopic composition is investigated with samples of normal water, heavy water, and partially deuterated water. When data below 0.25 GPa are excluded a free volume model fits the observed viscosities well yielding a theoretical glass transition density close to that observed in very-high-density amorphous ice. The improved fit above 0.25 GPa coincides with the loss of other anomalous behaviors in liquid water caused by hydrogen bonding and represents a transition to properties closer to those of a simple liquid.

74 ATOMIC AND MOLECULAR PHYSICS↗

DOE OSTI2023

Nucleation kinetics model for primary crystallization in Al–Y–Fe metallic glass

The high density of aluminum nanocrystals (>10 21 m -3 ) that develop during the primary crystallization in Al-based metallic glasses indicates a high nucleation rate (~10 18 m -3 s -1 ). Several studies have been advanced to account for the primary crystallization behavior, but none have been developed to completely describe the reaction kinetics. Recently, structural analysis by fluctuation electron microscopy has demonstrated the presence of the Al-like medium range order (MRO) regions as a spatial heterogeneity in as-spun Al 88 Y 7 Fe 5 metallic glass that is representative for the class of Al-based amorphous alloys that develop Al nanocrystals during primary crystallization. From the structural characterization, an MRO seeded nucleation configuration is established, whereby the Al nanocrystals are catalyzed by the MRO core to decrease the nucleation barrier. The MRO seeded nucleation model and the kinetic data from the delay time (τ) measurement provide a full accounting of the evolution of the Al nanocrystal density (N v ) during the primary crystallization under isothermal annealing treatments. Moreover, the calculated values of the steady state nucleation rates (J ss ) predicted by the nucleation model agree with the experimental results. Moreover, the model satisfies constraints on the structural, thermodynamic, and kinetic parameters, such as the critical nucleus size, the interface energy, and the volume-free energy driving force that are essential for a fully self-consistent nucleation kinetics analysis. In conclusion, the nucleation kinetics model can be applied more broadly to materials that are characterized by the presence of spatial heterogeneities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

In-Situ and Ex-Situ Studies on the Morphology Changes of Polymer Pipeline Materials for Use in Hydrogen Gas Environments

The US natural gas infrastructure is a national asset that could be used to deliver hydrogen and hydrogen blends of natural gas as a pathway to reduce carbon emissions. The distribution system comprises nearly 50% plastic pipe composed of medium- and high-density polyethylene materials (MDPE and HDPE). While these materials perform adequately for natural gas, research on their hydrogen compatibility is essential to understand if any immediate and long-term risks are associated with hydrogen addition. The Blended Gas CRADA, a HyBlend project, has established a comprehensive test method for evaluating MDPE and HDPE of various plastic resin compositions of pipeline material in pure hydrogen and 20% hydrogen/80% methane blends. Both in-situ and ex-situ measurements were performed to capture hydrogen-induced changes in the polyethylene material's crystalline, amorphous and their interphase regions. We investigated MDPE and HDPE pipeline materials made from different polymer resin systems to evaluate the effects of hydrogen gas. The materials were characterized by their density, diffusion coefficient, free volume ratio, and degree of crystallinity. Various advanced characterization methods, including in situ NMR, ex situ XRD, ex situ DSC, and ex situ TDA, were used to analyze the effects of changes in crystalline, amorphous, and interphase regions due to gas exposure. Time-dependent post-decompression quasi-static tensile tests were conducted to explore the effects of gas exposure time on the mechanical behavior of the pipe materials. This work will highlight the time sensitivities during and after gas exposure. The correlation between gas-induced polyethylene morphology changes and the associated material performance will be addressed for the intended applications. These studies will show that polyethylene resin composition and material exposure are important factors when considering whether hydrogen gas affects pipeline materials positively or negatively.

Simmons, Kevin L.↗

DOE OSTI2020

Polymer genome–based prediction of gas permeabilities in polymers

Abstract Predicting gas permeabilities of polymers a priori is a long-standing challenge within the membrane research community that has important applications for membrane process design and ultimately widespread adoption of membrane technology. From early attempts based on free volume and cohesive energy to more recent group contribution methods, the ability to predict membrane permeability has improved in terms of accuracy. However, these models usually stay “within the paper”, i.e. limited model details are provided to the wider community such that adoption of these predictive platforms is limited. In this work, we combined an advanced polymer chemical structure fingerprinting method with a large experimental database of gas permeabilities to provide unprecedented prediction precision over a large range of polymer classes. No prior knowledge of the polymer is needed for the prediction other than the repeating unit chemical formula. In addition, we have incorporated this model into the existing Polymer Genome project to make it open to the membrane research community.

Polymer Science↗

DOE OSTI2020

Modeling of SRS Aluminum-clad Spent Nuclear Fuel in Standard DOE Sealed Canisters

At the Savannah River Site (SRS), approximately 7 MTHM of aluminum-clad spent nuclear fuel is currently in wet storage at L-basin. A significant portion of this fuel is slated to be dried and sealed in DOE standard canisters for long-term storage. This report will focus on a few fuel types, which should bound all other fuel stored at SRS. These consist of the reference fuel assembly, the MURR fuel and the HFIR fuel. These bound a hypothetical maximum scenario for MTR box fuel, a maximum for decay heat in an assembly, and a maximum for the aluminum surface area, respectively. The geometry for the packages were created from DOE specifications for storage of each of the fuels. As long as the minimum time from reactor discharge to sealed storage is 3 years, then the highest temperatures which occur within the sealed canisters do not exceed 100° C for all scenarios considered here. In the geometry considered, while the HFIR fuel has a large surface area, the packaging configuration leaves large void areas, such that the aluminum surface to free volume ratio is about 30% less than an ATR or MURR packaging configuration.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Evaluation of Hydrogen Generation in High Burnup Demonstration Dry Storage Cask

This report provides a best-estimate evaluation of residual water content (post-dry out) in the High Burnup (HBU) LWR Spent Fuel Demonstration project TN-32 cask, and evaluates the radiolysis of the residual free water, and the physisorbed and chemisorbed waters on the surfaces of the fuel and cask internal contents. The evaluation of radiolytic breakdown of those waters with gamma radiation causing the generation of hydrogen gas (H 2 ) is made using available literature data and models. This evaluation is part of the overall materials performance evaluation of the SNF-in-canister system, and is part of the technical bases for their continued safe dry storage. The TN-32 cask contents included 32 HBU LWR spent fuel assemblies each with 264 fuel rods clad in zirconium alloys, aluminum neutron absorber components, and aluminum and stainless steel structural components. The residual free and surface (physisorbed/chemisorbed) waters are ascribed to water vapor in the free volume and to components’ surfaces, respectively. The total potential radiolytic hydrogen inventory from the water vapor and from waters ascribed to surfaces has been calculated assuming all the water produced molecular H 2 . The residual water that is chemically incorporated into the bulk of a hydrated oxide, i.e., chemisorbed water, and its total potential hydrogen inventory has been calculated. These calculations are at the physical limit of material available and are used for a bounding assessment purpose only.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Updated Estimate of Tritium Permeation from TPBAR Disposal Containers in ILV (U)

A tritium source term analysis was performed for TPBAR disposal in the E-Area Intermediate Level Vaults for the E-Area Low-Level Waste Facility Performance Assessment (PA). This analysis is based on an earlier source term analysis which treated the bulk oft he tritium residual as tightly bound by the TPBAR getter material, with only a small fraction existing as tritiated moisture in the lithium aluminate ceramic pellets. Together with atmospheric moisture trapped in the free volume, the tritiated water vapor is assumed to corrode steel surfaces inside the disposal container, covering them with a magnetite film while generating hydrogen. The carbon steel walls of the disposal container are permeable to hydrogen, providing a path way for tritium to escape containment. The rate of hydrogen generation is assumed to be limited by the rate of corrosion, which is assumed to be governed by parabolic reaction kinetics obtained from the literature. This relies on the further assumption that the water vapor consumed by the corrosion reaction is continually replaced by moisture from the lithium aluminate pellets until all of that moisture is gone. In addition to tritium permeation, the analysis also includes a slow leak through the disposal container walls at the maximum allowable leak rate, 1 x 1CH standard cm3/s. Results were obtained for four different combinations of internal and container wall temperatures, established in an earlier thermal analysis that considered two different vault loadings and two different TPBAR activity levels. Instantaneous release rates for these four cases are plotted in Figure ES-1 below

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2021

Collective Summary of sCO2 Materials Development (Supercritical Transformational Electric Power Generation (STEP) Level 2 Milestone Report) (Parts I - II)

Polymers such as PTFE (polytetrafluorethylene or Teflon), EPDM (ethylene propylene diene monomer) rubber, FKM fluoroelastomer (Viton), Nylon 11, Nitrile butadiene (NBR) rubber, hydrogenated nitrile rubber (HNBR) and perfluoroelastomers (FF_202) are commonly employed in super critical CO 2 (sCO2) energy conversion systems. O-rings and gaskets made from these polymers face stringent performance conditions such as elevated temperatures, high pressures, pollutants, and corrosive humid environments. In FY 2019, we conducted experiments at high temperatures (100°C and 120°C) under isobaric conditions (20 MPa). Findings showed that elevated temperatures accelerated degradation of polymers in sCO2, and that certain polymer microstructures are more susceptible to degradation over others. In FY 2020, the focus was to understand the effect of sCO2 on polymers at low (10 MPa) and high pressures (40 MPa) under isothermal conditions (100°C). It was clear that the same selectivity was observed in these experiments wherein certain polymeric functionalities showed more propensity to failure over others. Fast diffusion, supported by higher pressures and long exposure times (1000 hours) at the test temperature, caused increased damage in sCO2 environments to even the most robust polymers. We also looked at polymers under compression in sCO2 at 100°C and 20 MPa pressure to imitate actual sealing performance required of these materials in sCO2 systems. Compression worsened the physical damage that resulted from chemical attack of the polymers under these test conditions. In FY 2021, the effect of cycling temperature (from 50°C to 150°C to 50°C) for polymers under a steady sCO2 pressure of 20 MPa was studied. The aim was to understand the influence of cycling temperatures of sCO2 for typical polymers under isobaric (20 MPa) conditions. Thermoplastic polymers (Nylon, and PTFE) and elastomers (EPDM, Viton, Buna N, Neoprene, FF202, and HNBR) were subjected to 20 MPa sCO2 pressure for 50 cycles and 100 cycles in separate experiments. Samples were extracted for ex-situ characterization at 50 cycles and upon the completion of 100 cycles. Each cycle constituted of 175 minutes of cycling from 50°C to 150°C. The polymer samples were examined for physical and chemical changes by Dynamic Mechanical and Thermal Analysis (DMTA), Fourier Transform Infrared (FTIR) spectroscopy, and compression set. Density and mass changes immediately after removal from test were measured for degree of swell comparisons. Optical microscopy techniques and micro computer tomography (micro CT) images were collected on select specimens. Evaluations conducted showed that exposures to super-critical CO2 environments resulted in combinations of physical and/or chemical changes. For each polymer, the dominance of cycling temperatures under sCO2 pressures, were evaluated. Attempts were made to qualitatively link the permanent sCO2 effects to polymer micro- structure, free volume, backbone substitutions, presence of polar groups, and degree of crystallinity differences. This study has established that soft polymeric materials are conducive to failure in sCO2 through mechanisms of failure that are dependent on polymer microstructure and chemistry. Polar pendant groups, large atom substitutions on the backbone are some of the factors that are influential structural factors.

36 MATERIALS SCIENCE↗

DOE OSTI2023

A Design and Fabrication Options Trade Study for Metallic Fuel without Internal Sodium Bonding

Nuclear fuels using alloys of uranium, or metallic fuels, have many beneficial properties. The classical metallic fuel design uses a loose fitting cylindrical “slug” of fuel placed inside stainless-steel cladding tubes where the gap is filled with sodium. This sodium bond is liquid at operating temperature and conducts heat from the slug to the cladding, especially in early life before fuel swells into contact with the cladding. Despite the benefits of sodium bonding, there is a desire to develop metallic fuel technologies without it chiefly to reduce chemical reaction hazards in spent fuel storage from sodium fast reactors operating on once-through fuel cycles. Elimination of the sodium bond may also help unlock potential benefits for fuel fabrication, reactor neutronics, and compatibility with other types of reactors. Creating a sodium-free metallic fuel revolves around the problem of manufacturing fuel slug geometries which are in close contact with the cladding at beginning of life to facilitate heat transport while alleviating fuel-cladding chemical interactions (FCCI) at this interface and providing enough free volume to accommodate fuel swelling. Accelerating development and qualification of this fuel system will require careful selection of design and manufacturing options. To this end, a design trade-off study was performed to evaluate candidate options. Several design and manufacturing options were assessed, weighted, scored, and ranked with respect to fabrication, normal reactor operation, off-normal scenarios, and back-end considerations. This effort was performed both for “baseline” needs, which represented a once-through fuel cycle at temperatures and burnups known to be viable for sodium-bonded metallic fuel, and for “enhanced” needs to represent opportunities for closed fuel cycles and/or more aggressive temperatures/burnups. The outcomes of this study prioritized a baseline technology using U-Zr alloy with additives to mitigate FCCI, produced in annular slug geometry by continuous casting, clad in austenitic stainless-steel alloy, and followed by a final step to swage the cladding down to close the gap. This study prioritized an enhanced fuel technology using U-Mo alloy, also produced by continuous casting into an annular geometry, followed by coating/plating with an FCCI barrier on the slug, again with a final step to swage the cladding diameter down using oxide dispersion strengthened steel. It was noted that development of the enhanced fuel technology would entail more risk, thus U-Zr alloy was put forth as a backup to U-Mo if challenges are encountered with FCCI barriers, and advanced ferritic/martensitic steels are put forth as a backup to oxide dispersion strengthened steels if swaging and welding are found unworkable.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Quantification of Residual Water in Spent Fuel Dry Storage Canisters Using Mass Spectrometry

The purpose of this report is to document updates on the apparatus to simulate commercial vacuum drying procedures at the Nuclear Energy Work Complex at Sandia National Laboratories. Validation of the extent of water removal in a dry spent nuclear fuel storage system based on drying procedures used at nuclear power plants is needed to close existing technical gaps. Operational conditions leading to incomplete drying may have potential impacts on the fuel, cladding, and other components in the system during subsequent storage and disposal, such as fuel degradation; cladding corrosion, embrittlement, or breaching; and the creation of a flammable environment via radiolysis of water. A general lack of data suitable for model validation of commercial nuclear canister drying processes necessitates well-designed investigations of drying process efficacy and water retention. Scaled tests that incorporate relevant physics and well-controlled boundary conditions are essential to provide insight and guidance to the simulation of prototypic systems undergoing drying processes. This report documents details on the quantification of residual water in the Advanced Drying Cycle Simulator (ADCS), an apparatus built to simulate commercial drying procedures and quantify the amount of residual water remaining in a pressurized water reactor (PWR) fuel assembly after drying. The ADCS was constructed with a prototypic 17×17 PWR fuel skeleton and waterproof heater rods to simulate decay heat. The ADCS is outfitted with thermocouples to measure the thermal response of the ADCS to simulated decay heats and internal helium fill pressures relevant to commercial drying procedures. The ADCS is also instrumented with pressure transducers to measure the pressures and vacuum levels observed during simulated commercial drying. The most unique instrumentation used for quantifying residual water in the ADCS is a Hiden Analytical HPR-30 mass spectrometer (MS), which measures gas compositions of the ADCS internal free volume, based on partial pressures calculated from relative proportions of gas molecules detected by the MS. This report details the methodology used to implement MS measurements in quantifying residual water in the ADCS. This methodology includes the calibration of the HPR-30 MS to a Buck Research Instruments CR-4 chilled mirror hygrometer, which itself is calibrated to a NIST-traceable standard. Data collected by both the MS and the chilled mirror hygrometer from water/helium mixtures ranging from 150 to 500,000 ppmv water in helium were used to generate calibration curves, establishing a source of verification of MS measured water contents. Details regarding water content measurement uncertainties are included in this report, defining the accuracy and verifiability of the HPR-30 MS in measuring residual water content in simulated dry storage canister environments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Optimizing the Fabrication of Electrospun Nanofibrous Membrane Using Fractional Factorial Design

Electrospinning, a simple and easily tunable technique that utilizes the force balance between the electrostatic force and the solution surface tension to fabricate membranes out of 1D nanostructured fibers, has garnered much interest especially from the nanotechnology community. Depending on the morphology of the fibers, electrospun membrane has found its way in a wide range of applications, such as oil-water separation, desalination, tissue engineering, and batteries. During an electrospinning process, many factors can affect the morphology of the products, such as viscosity of the solution, voltage supply, discharge distance, feed rate of the solution, and electrospinning time. In this work, we investigated the impacts of the most important parameters on the morphology of electrospun fibrous membrane based on the fractional factorial design. We evaluated the electrospun fibrous membrane morphology using scanning electron microscopy (SEM) and capillary flow porometry. Poly (vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) was chosen for the current study due to its interesting and versatile functionalities including superior hydrophobicity, high free volume, and piezoelectricity. This work provides valuable insight for the fabrication of electrospun membranes, especially for tailoring membrane properties in accordance with any targeted applications.

Zhao, Yajing↗

DOE OSTI2022

CO2 Sorption in Ionic Liquid Crystals

Ionic liquid crystals (ILCs) have an affinity for certain polarizable gases such as CO2, due to their similarity to ionic liquids. We investigated three ILCs in the [1-alkyl-3-methylimidazolium+] family: n=12,14 with [BF4-] and [PF6-]: liquid crystalline analogues to ionic liquids with moderate (e.g., 1-2 mol%) CO2 solubility at atmospheric conditions: [1-butyl-3-methylimidazolium+] with [BF4-] and [PF6-]. While ionic liquids show high CO2 solubility, regenerating the CO2 is a high-energy process. Liquid crystals show low CO2 solubility but have a much lower regeneration energy requirement. Will ionic liquid crystals uptake CO2? What are the energy requirements of regenerating CO2? Conclusions: 1. C12mim BF4- shows the highest sorption at 0.12 wt% CO2 in the isotropic phase vs. C14mim BF4- with 0.097 wt% in the smectic phase. We hypothesize that the increase in chain length affects the free volume of the smectic vs. isotropic phase of C14mim BF4-, increasing the latter. 2. The change in anion from BF4- to PF6- decreased the sorption to an insignificant level more analogous to a physical adsorption onto the material in all phases. We hypothesize that the change in anion to the larger, less charge dense PF6- decreased the attractive forces between CO2 and the anion. 3. 0.12 wt% of CO2 in C12mim BF4- is small but significant. This in combination with the room temperature release of CO2 after only requiring refrigeration temperatures to occlude the CO2, making ionic liquid crystals promising materials for future.

carbon dioxide sorption↗

DOE OSTI2023

Salt Diapir‐Driven Recycling of Gas Hydrate

Abstract By harnessing both hypothetical, synthetic basin and gas hydrate (GH) system models and real‐world models of well‐studied salt diapir‐associated GH sites at Green Canyon (Gulf of Mexico) and Blake Ridge (U.S. Atlantic coast), we propose and demonstrate salt movement (and in particular, diapirism) to be a new mechanism for the recycling of marine GH. At Green Canyon, for example, we show that by considering this newly proposed diapir‐driven recycling mechanism in conjunction with previously proposed lithological control on sandy‐reservoir‐hosted hydrate at the base of the GH stability zone (BGHSZ; ∼bottom‐simulating reflector, BSR), modeled GH saturations match drilling data. Overall, salt diapir movement‐induced GH recycling provides a temperature‐driven mechanism by which GH saturations at the BGHSZ may reach >90 vol. % and by which GH volumes near and free gas volumes beneath the BGHSZ may be increased significantly through time. Interestingly, comparison of salt diapir‐driven recycling and sediment burial‐driven recycling scenarios suggests notably higher rates of recycling via diapir‐driven versus burial‐driven processes. Our results suggest that GH and associated free gas accumulations above salt diapir crests represent particularly attractive targets for unconventional and conventional hydrocarbon resource exploration and for scientific and academic drilling expeditions aimed at exploiting GH systems. Salt basins containing GH systems—including passive margin basins of the Gulf of Mexico, southeastern Brazil, and southwestern Africa—are therefore compelling localities for studying salt‐driven GH recycling and for salt diapir‐associated natural gas exploration.

58 GEOSCIENCES↗

DOE OSTI2024

Droplet bioprinting of acellular and cell-laden structures at high-resolutions

Advances in digital light projection(DLP) based (bio) printers have made printing of intricate structures at high resolution possible using a wide range of photosensitive bioinks. A typical setup of a DLP bioprinter includes a vat or reservoir filled with liquid bioink, which presents challenges in terms of cost associated with bioink synthesis, high waste, and gravity-induced cell settling, contaminations, or variation in bioink viscosity during the printing process. Here, we report a vat-free, low-volume, waste-free droplet bioprinting method capable of rapidly printing 3D soft structures at high resolution using model bioinks and model cells. A multiphase many-body dissipative particle dynamics model was developed to simulate the dynamic process of droplet-based DLP printing and elucidate the roles of surface wettability and bioink viscosity. Process variables such as light intensity, photo-initiator concentration, and bioink formulations were optimized to print 3D soft structures (∼0.4–3 kPa) with a typical layer thickness of 50 µm, an XY resolution of 38 ± 1.5 μm and Z resolution of 237 ± 5.4 µm. To demonstrate its versatility, droplet bioprinting was used to print a range of acellular 3D structures such as a lattice cube, a Mayan pyramid, a heart-shaped structure, and a microfluidic chip with endothelialized channels. Droplet bioprinting, performed using model C3H/10T1/2 cells, exhibited high viability (90%) and cell spreading. Additionally, microfluidic devices with internal channel networks lined with endothelial cells showed robust monolayer formation while osteoblast-laden constructs showed mineral deposition upon osteogenic induction. Overall, droplet bioprinting could be a low-cost, no-waste, easy-to-use, method to make customized bioprinted constructs for a range of biomedical applications.

DLP↗

DOE OSTI2024

3013 Fire Test 2020: Post-Test Volumes

Sandia National Laboratory conducted fire tests on ten 3013 containers with varying amounts of water. The containers plastically deformed during the fire tests. The plastic deformation increased the free-gas volume within the containers. The amount of plastic deformation is measured and post-test free gas volumes at 25°C is reported.

36 MATERIALS SCIENCE↗

DOE OSTI2022

To what extent can space be compressed? Bandwidth limits of spaceplates

Spaceplates are novel flat-optic devices that implement the optical response of a free-space volume over a smaller length, effectively “compressing space” for light propagation. Together with flat lenses such as metalenses or diffractive lenses, spaceplates have the potential to enable the miniaturization of any free-space optical system. While the fundamental and practical bounds on the performance metrics of flat lenses have been well studied in recent years, a similar understanding of the ultimate limits of spaceplates is lacking, especially regarding the issue of bandwidth, which remains as a crucial roadblock for the adoption of this platform. In this work, we derive fundamental bounds on the bandwidth of spaceplates as a function of their numerical aperture and compression ratio (ratio by which the free-space pathway is compressed). The general form of these bounds is universal and can be applied and specialized for different broad classes of space-compression devices, regardless of their particular implementation. Our findings also offer relevant insights into the physical mechanism at the origin of generic space-compression effects and may guide the design of higher performance spaceplates, opening new opportunities for ultra-compact, monolithic, planar optical systems for a variety of applications.

Shastri, Kunal (ORCID:0000000169282753)↗