Search NASA⌕ Search

SEARCH · Search NASA

Results for “GHz”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

10-30 GHz monolithic GaAs travelling-wave divider/combiner

A four-way monolithic GaAs traveling-wave power divider/combiner has been designed, fabricated and evaluated. With a design center frequency of 20 GHz, a bandwidth of from 10 GHz to 30 GHz has been measured. The insertion loss per dividing or combining action is less than 0.5 dB, with isolation between ports no worse than 20 dB. The input/output VSWRs are better than 2:1 across the same band. This divider/combiner can readily be used with monolithic GaAs power FET amplifiers to produce a several-fold increase in output powers over the 10 to 30 GHz frequency range.

Tserng, H. Q.↗

Ka-band (32-GHz) downlink capability for deep space communications

The first quarter century of U.S. solar system exploration using unmanned spacecraft has involved progressively higher operating frequencies for deep space telemetry: L-band (960 MHz) in 1962 to S-band (2.3 GHz) in 1964 to X-band (8.4 GHZ) in 1977. The next logical frequency to develop for deep space is the Ka-band (32 GHz) for which a primary deep space allocation of 500 MHz between 31.8 to 32.3 GHz was established in 1979. The telecommunications capability was improved by a factor of 77 (18.9 dB) through the frequency changes from L-band to X-band. Another improvement factor of 14.5 (11.6 dB) can be achieved by going to Ka-band. Plans to develop and demonstrate Ka-band capability include the continued measurement of weather effects at Deep Space Network (DSN) sites, development of a prototype DSN ground antenna and supporting subsystems, augmentation of planned spacecraft with Ka-band beacons, and development of spacecraft prototype modules for future Ka-band transmitters. Plans for augmenting the DSN with Ka-band capability by 1995 were also developed. A companion set of articles describes the Ka-band performance and technology in greater detail.

Smith, J. G.↗

Ka-band (32 GHz) benefits to planned missions

The benefits of using 32 GHz downlinks for a set of deep space missions, as well as the implications to radio science and the Deep Space Network (DSN) are documented. The basic comparison is between the use of the current X-band (8.4 GHz) and a 32 GHZ (Ka-band) downlink. There was shown to be approximately an 8 dB (about 600%) link advantage for 32 GHz. This 8 dB advantage would be able to either reduce mission cost or improve mission science return. Included here are studies on how the 8 dB advantage would be used for the Cassini and Mars Sample Return missions. While the work is preliminary, it shows that the 8 dB advantage can be exploited to provide large benefits to future deep space missions. There can be significant mass and/or power savings to the spacecraft, which can translate into cost savings. Alternatively, the increased downlink telecommunications performance can provide a greater science return.

Hansen, D. M.↗

Monitoring global vegetation using Nimbus-7 37 GHz data - Some empirical relations

The difference of the vertically and horizontally polarized brightness temperatures observed by the 37 GHz channel of the SMMR on board the Nimbus-7 satellite are correlated temporally with three indicators of vegetation density, namely the temporal variation of the atmospheric CO2 concentration at Mauna Loa (Hawaii), rainfall over the Sahel and the normalized difference vegetation index derived from the AVHRR on board the NOAA-7 satellite. SMMR 37 GHz and AVHRR provide complementary data sets for monitoring global vegetation, the 37 GHz data being more suitable for arid and semiarid regions as these data are more sensitive to changes in sparse vegetation. The 37-GHz data might be useful for understanding desertification and indexing Co2 exchange between the biosphere and the atmosphere.

Choudhury, B. J.↗

Physical retrieval of precipitation cell parameters using passive 118-GHz observations

Physical retrieval of precipitation parameters from 118-GHz spectra is investigated using an iterative planar-stratified numerical radiative-transfer model. Liquid and frozen hydrometeors are modeled as spherical Marshall-Palmer and Sekhon-Srivastava (SS) distributed Mie-scattering polydispersions, respectively, with Henyey-Greenstein phase functions. A comparison of 118-GHz rain-cell spectral perturbations observed during Cohmex with model calculations based on coincident radar data yields + or - 10 percent agreement over the convective core region, although a mean ice size 50 percent larger than that given by the SS distribution is required for agreement over the anvil region. A rain-cell model parameterized by top-altitude and total water density suggests that the dominant 118-GHz spectral modes can be used to retrieve top-layer altitude with rms errors of about 1-1.5 km, consistent with statistical retrieval results. Model calculations also suggest that cell density is not observable using 118-GHz spectra alone.

Gasiewski, A. J.↗

Retrieval of water vapor profiles from microwave radiometric measurements near 90 and 183 GHz

Upwelling radiometric measurements at 90 GHz and three side bands near 183 GHz are used to retrieve water vapor profiles over the ocean surface. An algorithm incorporating a new technique of handling moderate cloud cover is illustrated for the profiling of both relative humidity and water vapor burden. It is shown that the retrieved relative humidity profiles reflect gross features of the corresponding profiles recorded by the radiosondes. However, the retrieval generally cannot produce fine details of the observed profiles at altitudes where a rapid change in relative humidity occurs. For this reason, comparison of retrieved and observed values at a given altitude often yields an appreciable rms error. Profiling of water vapor burden, a parameter equivalent to total integrated water vapor above a certain altitude, results in much better agreement, as expected. The rms error obtained from the results of the retrieval at the surface is comparable to that derived from the combination of measurements at 18 GHz and 21 GHz channels of the Scanning Multichannel Microwave Radiometer aboard the Nimbus 7 satellite.

Wang, J. R.↗

One GHz digitizer for space based laser altimeter

This is the final report for the research and development of the one GHz digitizer for space based laser altimeter. A feasibility model was designed, built, and tested. Only partial testing of essential functions of the digitizer was completed. Hybrid technology was incorporated which allows analog storage (memory) of the digitally sampled data. The actual sampling rate is 62.5 MHz, but executed in 16 parallel channels, to provide an effective sampling rate of one GHz. The average power consumption of the one GHz digitizer is not more than 1.5 Watts. A one GHz oscillator is incorporated for timing purposes. This signal is also made available externally for system timing. A software package was also developed for internal use (controls, commands, etc.) and for data communication with the host computer. The digitizer is equipped with an onboard microprocessor for this purpose.

Staples, Edward J.↗

Hysteresis effects in instantaneous frequency scaling of attenuation on 20 and 30 GHz satellite links

It has been observed with 20/30 GHz satellite beacon measurements that the ratio of 30 GHz to 20 GHz attenuation changes during some fade events. This ratio displays a hysteresis effect. This effect can be explained by a change in the drop size distribution (DSD) during the event. However, it appears only above approximately 6-8 dB of attenuation at 20 GHz. Instantaneous frequency scaling of attenuation is being proposed as part of an algorithm for uplink power control (ULPC) and the dynamic range of such an algorithm must be appropriately limited to avoid the hysteresis.

Sweeney, D. G.↗

A low noise 230 GHz heterodyne receiver employing .25 sq micron area Nb/AlO(x)/Nb tunnel junctions

Recent results for a full height rectangular waveguide mixer with an integrated IF matching network are reported. Two 0.25 sq micron Nb/AlO(x)/Nb superconducting insulating superconducting (SIS) tunnel junctions with a current density of about 8500 A/sq cm and omega RC of about 2.5 at 230 GHz have been tested. Detailed measurements of the receiver noise have been made from 200-290 GHz for both junctions at 4.2 K. The lowest receiver noise temperatures were recorded at 239 GHz, measuring 48 K DSB at 4.2 K and 40 K DSB at 2.1 K. The 230 GHz receiver incorporates a one octave wide integrated low pass filter and matching network which transforms the pumped IF junction impedance to 50 ohms over a wide range of impedances.

Kooi, Jacob W.↗

Double dipole antenna SIS receivers at 100 and 400 GHz

Antenna patterns were measured between 95 and 120 GHz for a double dipole antenna / ellipsoidal lens combination. The structure produces a non-astigmatic beam with low side lobe levels over that whole band. A heterodyne SIS receiver based on this concept gave a best noise temperature of 145 K DSB at 98 GHz. Measurements were also made with a 400 GHz heterodyne SIS receiver, using a double dipole antenna in conjunction with a hyperhemispherical lens. The best noise temperature was 220 K DSB at 402 GHz. On-chip stubs were used to tune out the SIS junction capacitance.

Skalare, A.↗

Retrieval of total precipitable water over high-latitude regions using radiometric measurements near 90 and 183 GHz

Radiometric measurements at 90 GHz and three sideband frequencies near the peak water vapor absorption line of 183.3 GHz were made with Advanced Microwave Moisture Sounder (AMMS) aboard the NASA DC-8 aircraft during the Global Aerosol Backscatter Experiment (GLOBE) mission over the Pacific Ocean in November 1989. Some of the measurements over the high-latitude regions (greater than 50 deg N or 50 deg S) were analyzed for the retrieval of total precipitable water less than 0.5 g/sq cm both over land and ocean surfaces. The results show that total precipitable water from a relatively dry atmosphere could be estimated with high sensitivity from these radiometric measurements. The retrieved values over ocean surface show a decrease toward the polar region as expected. The retrieved total precipitable water over land correlates positively with the aircraft radar altitude. This positive correlation is expected because the aircraft radar altitude provides a measure of atmospheric water vapor burden above the surface. Retrieved high reflectivities over land surface at 90 GHz and 183 GHz are presumably related to snow cover on the ground. This suggests that radiometric measurements at these frequencies could be used to map snow at high-latitude regions.

Wang, J. R.↗

Microjansky source counts and spectral indices at 8.44 GHz

Deep images were made with 10 arcsec resolution at 8.44 GHz with microjansky sensitivity of two regions previously imaged at several lower frequencies. The differential microjansky source count fits a power-law distribution with slope 2.3 +/- 0.2. This slope is roughly constant between 1.41 and 8.44 GHz and between S(v) = about 4 and X(v) = 1000 microJy. Unless the majority of radio sources at microJy levels are local, their average luminosity and/or space density probably has evolved with cosmic epoch in order to sustain the steep and nearly Euclidean value of the slope over such a large range in flux density. The 8.44 GHz counts probably converge at less than the 1 microjansky level if the evolutionary properties of these weak sources are similar to those of luminous gE radio galaxies and quasars. The median angular size of sources detected at 8.44 GHz at microjansky levels is 2.6 +/- 1.4 arcsec, and 40 percent of the source are larger than 5 arcsec.

Windhorst, Rogier A.↗

Statistical results from the Virginia Tech propagation experiment using the Olympus 12, 20, and 30 GHz satellite beacons

Virginia Tech has performed a comprehensive propagation experiment using the Olympus satellite beacons at 12.5, 19.77, and 29.66 GHz (which we refer to as 12, 20, and 30 GHz). Four receive terminals were designed and constructed, one terminal at each frequency plus a portable one with 20 and 30 GHz receivers for microscale and scintillation studies. Total power radiometers were included in each terminal in order to set the clear air reference level for each beacon and also to predict path attenuation. More details on the equipment and the experiment design are found elsewhere. Statistical results for one year of data collection were analyzed. In addition, the following studies were performed: a microdiversity experiment in which two closely spaced 20 GHz receivers were used; a comparison of total power and Dicke switched radiometer measurements, frequency scaling of scintillations, and adaptive power control algorithm development. Statistical results are reported.

Stutzman, Warren L.↗

Radiometric observations of atmospheric attenuation at 20.6 and 31.65 GHz: The Wave Propagation Laboratory data base

The National Oceanic and Atmospheric Administration (NOAA) Wave Propagation Laboratory (WPL) presently operates five dual-channel microwave radiometers, one triple-channel microwave radiometer, and one six-channel microwave radiometer. The dual-channel radiometers operate at frequencies of 20.6 or 23.87 GHz and 31.4 or 31.65 GHz. The triple-channel radiometer operates at 20.6, 31.65, and 90.0 GHz. The six-channel radiometer operates at frequencies of 20.6, 31.65, 52.85, 53.85, 55.45, and 58.8 GHz. Recent brightness temperature measurements and attenuation values from some of the above radiometers are presented. These radiometric measurements, taken in different locations throughout the world, have given WPL a diverse set of measurements under a variety of atmospheric conditions. We propose to do a more complete attenuation analysis on these measurements in the future. In addition, a new spinning reflector was installed recently for the dual-channel radiometer at the Platteville, Colorado site. This reflector will extend our measurement capabilities during precipating conditions. Locating the three-channel and portable dual-channel radiometers at or near Greeley, Colorado to support the Advanced Communications Technology Satellite (ACTS) program is discussed.

Jacobson, Mark D.↗

Behavior of an inversion-based precipitation retrieval algorithm with high-resolution AMPR measurements including a low-frequency 10.7-GHz channel

A microwave-based, profile-type precipitation retrieval algorithm has been used to analyze high-resolution passsive microwave measurements over an ocean background, obtained by the Advanced Microwave Precipitation Radiometer (AMPR) flown on a NASA ER-2 aircraft. The analysis is designed to first determine the improvements that can be gained by adding brightness temperature information from the AMPR low-frequency channel (10.7 GHz) to a multispectral retrieval algorithm nominally run with satellite information at 19, 37, and 85 GHz. The impact of spatial resolution degradation of the high-resolution brightness temperature information on the retrieved rain/cloud liquid water contents and ice water contents is then quantified in order to assess the possible biases inherent to satellite-based retrieval. Careful inspection of the high-resolution aircraft dataset reveals five distinctive brightness temperature features associated with cloud structure and scattering effects that are not generally detectable in current passive microwave satellite measurements. Results suggest that the inclusion of 10.7-GHz information overcomes two basic problems associated with three-channel retrieval. Intercomparisons of retrievals carried out at high-resolution and then averaged to a characteristic satellite scale to the corresponding retrievals in which the brightness temperatures are first convolved down to the satellite scale suggest that with the addition of the 10.7-GHz channel, the rain liquid water contents will not be negatively impacted by special resolution degradation. That is not the case with the ice water contents as they appear ti be quite sensitive to the imposed scale, the implication being that as spatial resolution is reduced, ice water contents will become increasingly underestimated.

Smith, E. A.↗

Absorption by H2O and H2O-N2 mixtures at 153 GHz

New experimental data on and a theoretical analysis of the absorption coefficient at 153 GHz are presented for pure water vapor and water vapor-nitrogen mixtures. This frequency is 30 GHz lower than the resonant frequency of the nearest strong water line (183 GHz) and complements our previous measurements at 213 GHz. The pressure dependence is observed to be quadratic in the case of pure water vapor, while in the case of mixtures there are both linear and quadratic density components. By fitting our experimental data taken at several temperatures we have obtained the temperature dependence of the absorption. Our experimental data are compared to several theoretical models with and without a continuum contribution, and we find that none of the models is in very good agreement with the data; in the case of pure water vapor, the continuum contribution calculated using the recent theoretical absorption gives the best results. In general, the agreement between the data and the various models is less satisfactory than found previously in the high-frequency wing. The anisotropy in the observed absorption differs from that currently used in atmospheric models.

Bauer, A.↗

Low-cost 20-22 GHz MIC active receiver/radiometer

A microwave integrated circuit active receiver is built and tested at 19-25 GHz. The receiver consists of a planar CPW-fed double folded-slot antenna coupled to a six-stage MESFET (metal semiconductor field effect transistors) amplifier and followed by a planar Schottky-diode detector. The folded-slot antenna on a GaAs half-space results in a wide frequency bandwidth suitable for MMIC amplifiers. The measured system performance show a video responsivity close to 1 GV/W at 20 GHz with a 3-dB bandwidth of 1500 MHz. A novel method which uses the planar video detector after the amplifier stages as an RF (radio frequency) mixer is used to measure the noise-figure of the direct detection radiometer. The system noise figure is 4.8 dB at 22 GHz. The radiometer sensitivity to a hot/cold load is 3.8 mu V/K. The measured antenna patterns show a 90% Gaussicity at 20-22 GHz. The active MIC receiver can be integrated monolithically for low-cost applications and is well suited for millimeter-wave linear imaging arrays.

PLANAR SCHOTTKY DIODE DETECTOR↗

Computer Analysis of Spectrum Anomaly in 32-GHz Traveling-Wave Tube for Cassini Mission

Computer modeling of the 32-GHz traveling-wave tube (TWT) for the Cassini Mission was conducted to explain the anomaly observed in the spectrum analysis of one of the flight-model tubes. The analysis indicated that the effect, manifested as a weak signal in the neighborhood of 35 GHz, was an intermodulation product of the 32-GHz drive signal with a 66.9-GHz oscillation induced by coupling to the second harmonic'signal. The oscillation occurred only at low- radiofrequency (RF) drive power levels that are not expected during the Cassini Mission. The conclusion was that the anomaly was caused by a generic defect inadvertently incorporated in the geometric design of the slow-wave circuit and that it would not change as the TWT aged. The most probable effect of aging on tube performance would be a reduction in the electron beam current. The computer modeling indicated that although not likely to occur within the mission lifetime, a reduction in beam current would reduce or eliminate the anomaly but would do so at the cost of reduced RF output power.

Dayton, James A., Jr.↗