Search NASA⌕ Search

SEARCH · Search NASA

Results for “GRAIN BOUNDARY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Analysis of defect structure in silicon. Characterization of SEMIX material. Silicon sheet growth development for the large area silicon sheet task of the low-cost solar array project

Statistically significant quantitative structural imperfection measurements were made on samples from ubiquitous crystalline process (UCP) Ingot 5848 - 13C. Important correlation was obtained between defect densities, cell efficiency, and diffusion length. Grain boundary substructure displayed a strong influence on the conversion efficiency of solar cells from Semix material. Quantitative microscopy measurements gave statistically significant information compared to other microanalytical techniques. A surface preparation technique to obtain proper contrast of structural defects suitable for quantimet quantitative image analyzer (QTM) analysis was perfected and is used routinely. The relationships between hole mobility and grain boundary density was determined. Mobility was measured using the van der Pauw technique, and grain boundary density was measured using quantitative microscopy technique. Mobility was found to decrease with increasing grain boundary density.

Natesh, R.↗
NASA NTRS2018

Impact of Powder Variability on the Microstructure and Mechanical Behavior of Selective Laser Melted Alloy 718

Powder-bed additive manufacturing processes use fine powders to build parts layer-by-layer. Alloy 718 powder feedstocks for selective laser melting (SLM) additive manufacturing are produced commercially by both gas and rotary atomization and are available typically in the 10-45 or 15-45 microns size ranges. A comprehensive investigation was conducted to understand the impact of powder variability on the microstructure and mechanical behavior of SLM 718 heat treated to Aerospace Material Specification (AMS) 5664. This study included sixteen virgin powders and three once-recycled powders within the 10-45 and 15-45 microns size ranges that were obtained from seven direct source suppliers and one reseller. Although alike as highly regular spheroids, these powders showed distinct differences in composition (especially Al, C and N contents), particle size distributions, and powder features such as degree of agglomeration, fusion and surface roughness. Compositional differences expectedly had the strongest impact on microstructure. High N and C contents formed TiN-nitrides and/or (Nb,Ti,Mo)-C carbides on the grain boundaries, prevented recrystallization during heat treatment, and resulted in retained (001)-scalloped shaped grains that ranged from 19 to 41 microns in average size. In the absence of this particle pinning, the average grain size of the heat treated SLM 718 ranged from 51 microns to 90 microns. Room temperature tensile and high cycle fatigue (HCF) testing compared as-fabricated (AF) and low stress ground (LSG) surface conditions. Tensile testing revealed consistent behavior between the two surface conditions and amongst the powder lots. The finer grained SLM 718 builds displayed the lowest tensile properties. A SLM 718 build fabricated from a powder with eight times lower C content showed statistically better tensile properties presumably due to enhanced coarsening of (delta)-Ni3Nb precipitates. The specimens from once-recycled powders had slightly higher tensile strengths and slightly higher ductility compared to their virgin equivalents; once-recycling also did not substantially degrade the mean HCF life. The LSG fatigue lives agreed with conventionally manufactured 718 data, while AF lives exhibited a knock-down due to surface roughness. The fatigue lives of AF specimens were statistically equivalent across powder lots except for one and failures typically initiated at stress concentrators associated with SLM surface asperities. Fatigue testing of low stress ground specimens result in both transgranular and within facet crack initiations. More than half of the cracks initiated from these facets for the machined condition; however, these facets appeared to be within grains that were larger-than-average in size. A nitrogen-atomized powder with fine prior particles of TiN-nitrides and M(Ti,Nb,Mo)C carbides from atomization on powder surfaces resulted in the best fatigue performance with segregation of these particles to the SLM 718 grain boundaries leading to higher resistance to early-stage crack propagation. Typically the fine-grained builds with minor phases along the grain boundaries did not perform well in fatigue, whereas a larger-grain build with lower carbon content and coarser delta-Ni3Nb precipitates showed the next best HCF response. Further details of the build microstructure and its impact on tensile and fatigue behavior was considered.

laser deposition↗
NASA NTRS1974

The use of the ion probe mass spectrometer in the measurement of hydrogen concentration gradients in Monel K 500

The ion probe mass spectrometer was used to measure hydrogen concentration gradients in cathodically charged Monel K 500. Initial work with the ion probe involved the calibration of the instrument and the establishment of a suitable experimental procedure for this application. Samples of Monel K 500 were cathodically charged in a weak sulfuric acid solution. By varying the current density, different levels of hydrogen were introduced into the samples. Hydrogen concentration gradients were taken by ion sputtering on the surface of these samples and monitoring the behavior of the hydrogen mass peak as a function of time. An attempt was made to determine the relative amounts of hydrogen in the bulk and grain boundaries by analyzing a fresh fracture surface with a higher proportion of grain boundary area. It was found that substantially more hydrogen was detected in the grain boundaries than in the bulk, confirming the predictions of previous workers. A sputter rate determination was made in order to establish the rate of erosion.

Truhan, J. J., Jr.↗
NASA NTRS1985

Characterization of erosion of metallic materials under cavitation attack in a mineral oil

Cavitation erosion and erosion rates of eight metallic materials representing three crystal structures were studied. The erosion experiments were conducted with a 20-kHz ultrasonic magnetostrictive oscillator in a viscous mineral oil. The erosion rates of the metals with an fcc matrix were 10 to 100 times higher than that of an hop-matrix titanium alloy. The erosion rates of iron and molybdenum, with bcc matrices, were higher than that of the titanium alloy but lower than those of those of the fcc materials. Studies with scanning electron microscopy indicated that the cavitation pits were initially formed at the grain boundaries and precipitates and that the pits formed at the junction of grain boundaries grew faster than the others. Transcrystalline craters formed by cavitation attack over the surface of grains and roughened the surfaces by multiple slip and twinning. Surface roughness measurements showed that the pits that formed over the grain boundaries deepened faster than pits. Computer analysis revealed that a geometric expression describes the nondimensional erosion curves during the time period 0.5 t (sub 0) t 2.5 t (sub 0), where t (sub 0) is the incubation period. The fcc metals had very short incubation periods; the titanium alloy had the longest incubation period.

Rao, B. C. S.↗
NASA NTRS1986

Processing-structure characterization of rheocast IN-100 superalloy

The rheocasting solidification process was applied in the production of IN-100 nickel base superalloy, and the effects of processing variables, such as stirring speed, isothermal stirring time, and volume fraction solid during isothermal stirring, on the resultant rheocast structure were investigated. Ingots that were furnace cooled at the same rate but without stirring were compared with the rheocast ingots. Rheocasting yielded fine-grained structures, where the extent of microsegregation, the variation in macrostructure, and the solidification-induced porosity and ingot cracking were found to be reduced in comparison to the unstirred ingots. The grain size and nonuniformity were reduced by increasing the stirring speed, isothermal stirring time, or the volume fraction solid during stirring; decreased microsegregation was achieved by an increase in the volume fraction solid. The structures of grain boundaries lent support to the grain boundary mechanism proposed by Vogel et al. (1977) for rheocasting.

Cheng, Jung-Jen Allen↗
NASA NTRS1990

High-temperature deformation and microstructural analysis for Si3N4-Sc2O3

It was indicated that Si3N4 doped with Sc2O3 may exhibit high temperature mechanical properties superior to Si3N4 systems with various other oxide sintered additives. High temperature deformation of samples was studied by characterizing the microstructures before and after deformation. It was found that elements of the additive, such as Sc and O, exist in small amounts at very thin grain boundary layers and most of them stay in secondary phases at triple and multiple grain boundary junctions. These secondary phases are devitrified as crystalline Sc2Si2O7. Deformation of the samples was dominated by cavitational processes rather than movements of dislocations. Thus the excellent deformation resistance of the samples at high temperature can be attributed to the very small thickness of the grain boundary layers and the crystalline secondary phase.

Cheong, Deock-Soo↗
NASA NTRS1992

High-temperature deformation and microstructural analysis for silicon nitride-scandium(III) oxide

It was indicated that Si3N4 doped with Sc2O3 may exhibit high temperature mechanical properties superior to Si3N4 systems with various other oxide sintered additives. High temperature deformation of samples was studied by characterizing the microstructures before and after deformation. It was found that elements of the additive, such as Sc and O, exist in small amounts at very thin grain boundary layers and most of them stay in secondary phases at tripple and multiple grain boundary junctions. These secondary phases are devitrified as crystalline Sc2Si2O7. Deformation of the samples was dominated by cavitational processes rather than movements of dislocations. Thus the excellent deformation resistance of the samples at high temperature can be attributed to the very small thickness of the grain boundary layers and the crystalline secondary phase.

Cheong, Deock-Soo↗
NASA NTRS1983

Compositional effects on Si3N4 fracture surfaces

Surface analysis techniques (X-ray, infrared reflection spectroscopy, Auger electron spectroscopy) applied to the same samples reveal that fracture surfaces of Si3N4 with Y2O3 densification aids possess a higher concentration of oxygen than the bulk. The oxide densification aids thus concentrate in the grain boundaries, and even low-temperature fracture is seen as occurring preferentially within the oxygen-enriched grain boundaries. It is found that increasing the concentrations of Y2O3 and Al2O3 increases the oxygen content of the fracture surface. A range of 13-15 percent Y2O3 + 6 percent Al2O3 gives an amorphous grain-boundary phase that is resistant to devitrification. Fracture occurs through the amorphous phase, and heat treatment at 1000 C has little effect on the amorphous phase.

Hench, L. L.↗
NASA NTRS1983

Micromechanically Based Constitutive Relations for Polycrystalline Solids

A basic method to estimate the overall mechanical response of solids which contain periodically distributed defects is presented. The method estimates the shape and growth pattern of voids periodically distributed over the grain boundaries in a viscous matrix. The relaxed moduli are obtained for a polycrytalline solid that undergoes relaxation by grain boundary sliding which accounts for the interaction effects. The overall inelastic nonlinear response at elevated temperatures in terms of a model which considers nonlinear power law creep within the grains, and linear viscous flow in the grain boundaries is discussed.

Nemat-Nasser, S.↗
NASA NTRS1980

The influence of isothermal annealing on the molybdenum fibers of a directed solid gamma/gamma prime - alpha alloy

The mechanical characteristics of the directed solid eutectic Ni-Al-Mo (gamma/gamma prime)-alpha alloy at high temperatures make it useful in the blades of gas turbines. Structural changes are observed for the alloy under isothermal annealing, particularly the formation of molybdenum plates at the grain boundary and an increase of the gamma phase in relation to the gamma prime phase. Molybdenum lamellas appear at the grain boundary above 1100 C which can have a negative influence on the mechanical properties. The change in the structure near the grain boundary with the increase in temperature is illustrated through a sequence of pictures.

Whittenberger, J. D.↗
NASA NTRS1980

The interaction of molten silicon with silicon aluminum oxynitrides

Silicon aluminum oxynitride solid solutions (sialons) based on beta-Si3N4 and Si2N2O behave differently in contact with molten silicon. The Si2N2O-based sialons convert to almost pure Si3N4, apparently through a two-step decomposition and solution-precipitation reaction, whereas the beta-Si3N4 sialons are preferentially attacked at the grain boundaries. The composition of the grain-boundary phase appears to control the rate of reaction.

Wills, R. R.↗
NASA NTRS1984

Limiting mechanisms in large-grain polycrystalline silicon Spatial homogeneity

An experiment to investigate the spatial homogeneity of large-grain polycrystalline silicon shows a number of performance-loss mechanisms. Arrays of up to 400 small (about 0.2 sq cm in area) photodiodes were fabricated on a selection of 10 cm x 10 cm polycrystalline silicon wafers. Measurements of the illuminated current-voltage (J-V) characteristics were used to generate maps of Voc, Jsc, and FF as a function of position; and dark J-V and LBIC analysis were used to determine the cause of low performance in areas with significantly degraded J-V characteristics. In addition to the presence of inclusions, which act as resistive shunts, the performance of many of the cells is limited by quasineutral recombination current, which may vary by up to an order of magnitude across a wafer. The increase is the result of either electrically-active grain boundaries or numerous subgrain boundaries within the grain bulk. In other isolated instances, the open-circuit voltage is reduced by excess space-charge recombination current that is not correlated with either grain or subgrain boundary activity.

Culik, J.↗
NASA NTRS1991

Diffusion mechanisms in Ir-coated Re for high-temperature, radiation-cooled rocket thrusters

Materials used for radiation-cooled rocket thrusters must be capable of surviving under extreme conditions of high temperatures and oxidizing environments. Thruster chambers were developed using chemical-vapor-deposited (CVD) Re coated with CVD Ir on the inside surface which is exposed to hot combustion gases. Ir serves as an oxidation barrier protecting the Re which maintains structural integrity at high temperatures. In order to predict and extend the performance limits of these Ir-coated Re thrusters, the diffusion kinetics of CVD materials at temperature are studied. Thruster end ring sections were examined using electron microprobe analysis both before and after exposure to high temperature vacuum environments. The resulting elemental maps for Re, Ir, and Mo in the near-surface region allow identification of diffusion mechanisms operating at these temperatures. Line scans for Ir and Re were fit using a diffusion model to extract relevant diffusion constants. The fastest diffusion process is seen to be grain boundary diffusion with Re diffusing down grain boundaries in the Ir overlayer. The measured dependence of the diffusion rate on temperature will allow prediction of operating lifetimes for these thrusters.

Hamilton, J. C.↗
NASA NTRS1992

Diffusion mechanisms in chemical vapor-deposited iridium coated on chemical vapor-deposited rhenium

Radiation-cooled rocket thruster chambers have been developed which use CVD Re coated with CVD Ir on the interior surface that is exposed to hot combustion gases. The Ir serves as an oxidation barrier which protects the structural integrity-maintaining Re at elevated temperatures. The diffusion kinetics of CVD materials at elevated temperatures is presently studied with a view to the prediction and extension of these thrusters' performance limits. Line scans for Ir and Re were fit on the basis of a diffusion model, in order to extract relevant diffusion constants; the fastest diffusion process is grain-boundary diffusion, where Re diffuses down grain boundaries in the Ir overlayer.

Hamilton, J. C.↗
NASA NTRS1983

TEM and SEM (EBIC) investigations of silicon bicrystals

The electrical and structural properties of low and medium angle tilt grain boundaries in silicon bicrystals were studied in order to obtain insight into the mechanisms determining the recombination activity. The electrical behavior of these grain boundaries was studied with the EBIC technique. Schottky barriers rather than p-n junctions were used to avoid annealing induced changes of the structure and impurity content of the as-grown crystals. Transmission electron spectroscopy reveals that the 20 deg boundary is straight, homogeneous, and free of extrinsic dislocations. It is concluded that, in the samples studied, the electrical effect of grain boundaries appears to be independent of the boundary misorientation. The dominant influence appears to be impurity segregation effects to the boundary. Cleaner bicrystals are required to study intrinsic differences in the electrical activity of the two boundaries.

Gleichmann, R.↗
NASA NTRS1974

Shock-induced melting in anorthositic rock 60015 and a fragment of anorthositic breccia from the 'picking pot' /70052/

Microscopic and chemical evidence are presented to support the contention that shock-generated incipient grain-boundary melting of plagioclase occurred in an anorthositic lunar rock and that shock-generated plagioclase liquid was present along grain boundaries during post-shock adiabatic expansion in a fragment of anorthositic breccia. The first contention is supported by microtextural relationships in the rock, the composition of its metal particles (most iron with some cobalt and less nickel), and glass inclusions with vapor bubbles. The second contention is supported by angular irregular voids in the fragment as well as the occurrence of oriented glass filaments in some of the voids. It is shown that shock-generation of 'cataclastic anorthosite' and high-temperature plagioclase liquids can explain the exceptionally young lead and argon ages of the anorthositic rock. The results of the breccia study indicate that shock lithification of plagioclase-rich particulate material from the highland regolith is due to grain-boundary melting of plagioclase.

Sclar, C. B.↗
NASA NTRS1987

Electrical conductivity of chondritic meteorites

The electrical conductivity of samples of the Murchison and Allende carbonaceous chondrites is 4 to 6 orders of magnitude greater than rock forming minerals such as olivine for temperatures up to 700 C. The remarkably high electrical conductivity of these meteorites is attributed to carbon at the grain boundaries. Much of this carbon is produced by pyrolyzation of hydrocarbons at temperatures in excess of 150 C. As the temperature increases, light hydrocarbons are driven off and a carbon-rich residue or char migrates to the grain boundaries enhancing electrical conductivity. Assuming that carbon was present at the grain boundaries in the material which comprised the meteorite parent bodies, the electrical heating of such bodies was calculated as a function of body size and solar distance during a hypothetical T-Tauri phase of the sun. Input conductivity data for the meteorite parent body were the present carbonaceous chondrite values for temperatures up to 840 C and the electrical conductivity values for olivine above 840 C.

Duba, AL↗
NASA NTRS1988

The effect of diffusive segregation on the fracture of hydrogen charged nickel

Hydrogen charged nickel was deformed in tension at a test temperature of 208 K to study the diffusive segregation of hydrogen during straining and the dependence of embrittlement on grain boundary hydrogen concentration and deformation rate. Tests were performed on samples in the as-quenched condition at various strain rates. An increase in the degree of embrittlement at slow strain rates can be attributed to diffusive segregation of hydrogen to grain boundaries during the test period. The embrittlement of samples with equal grain boundary hydrogen concentration was found to be relatively insensitive to strain rate, bulk hydrogen concentration and the total time at the test temperature.

Lassila, D. H.↗