Search NASA⌕ Search

SEARCH · Search NASA

Results for “GRAMS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Improbability of Nuclear Criticality in Compacted Criticality Control Overpacks after Room Closure by Salt Creep at Waste Isolation Pilot Plant

Based on the rationale presented, nuclear criticality is improbable after salt creep causes compaction of criticality control overpacks (CCOs) disposed at the Waste Isolation Pilot Plant, an operating repository in bedded salt for the disposal of transuranic (TRU) waste from atomic energy defense activities. For most TRU waste, the possibility of post-closure criticality is exceedingly small either because the salt neutronically isolates TRU waste canisters or because closure of a disposal room from salt creep does not sufficiently compact the low mass of fissile material. The criticality potential has been updated here because of the introduction of CCOs, which may dispose up to 380 fissile gram equivalent plutonium-239 in each container. The criticality potential is evaluated through high-fidelity geomechanical modeling of a disposal room filled with CCOs during two representative conditions: (1) large salt block fall, and (2) gradual salt compaction (without brine seepage and subsequent gas generation to permit maximum room closure). Geomechanical models of rock fall demonstrate three tiers of CCOs are not greatly disrupted. Geomechanical models of gradual room closure from salt creep predict irregular arrays of closely packed CCOs after 1000 years, when room closure has asymptotically approached maximum compaction. Criticality models of spheres and cylinders of 380 fissile gram equivalent of plutonium (as oxide) at the predicted irregular spacing demonstrate that an array of CCOs is not critical when surrounded by salt and magnesium oxide, provided the amount of hydrogenous material shipped in the CCO (usually water and plastics) is controlled or boron carbide (a neutron poison) is mixed with the fissile contents.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Post-closure Nuclear Criticality Safety Evaluations for Disposition of Criticality Control Overpacks at the Waste Isolation Pilot Plant

The Waste Isolation Pilot Plant (WIPP) is a geological repository in southern New Mexico that provides for disposal of transuranic (TRU) wastes from atomic energy defense activities. The Sandia National Laboratories (Sandia) Report, Consideration of Nuclear Criticality When Disposing of Transuranic Waste at the Waste Isolation Pilot Plant, addresses nuclear criticality safety based on the projected inventory characteristics for the initial compliance certification application of WIPP in 1996. As the inventory, waste forms, and disposal package designs change, revised or new analyses are necessary to demonstrate acceptability for these configurations within the WIPP safety basis and compliance with 10,000-year post-closure standards of the US Environmental Protection Agency (EPA). Saylor and Scaglione evaluated criticality control overpacks (CCOs) in 2017 based on conservative assumptions for post-closure repository structural conditions with resulting effects on containers and container spacing, The Saylor and Scaglione evaluation of CCOs addressed a single waste configuration that represents the Surplus Plutonium Disposition Program’s dilute and dispose waste form and composition. This initial CCO study demonstrated that 50 grams of boron carbide (B 4 C) per CCO is sufficient to ensure post-closure criticality safety based on a well-mixed waste composition, and Oak Ridge National Laboratory (ORNL) subsequently determined that this amount of B 4 C does not require constraints on moisture or plastic present as moderator. The Saylor and Scaglione analysis conservatively assumes repository room closure that eliminates all space between fissile gram equivalent (FGE) 239 Pu masses. The close-packed array was selected based on limited availability of repository salt creep modeling results at that time. In 2019, Brickner provided additional evaluations for pipe overpack containers (POCs), building on the conservative basis provided by Saylor and Scaglione. Brickner’s 2019 analysis made use of new geomechanical data for post-closure spacing that rely on advances in repository modeling as documented in the work by Reedlunn and Bean. This current CCO evaluation for generic waste materials expands on earlier work performed at ORNL and includes evaluation of CCOs across a much broader range of possible waste compositions and geometries. This evaluation is intended to provide input for the required feature, event and process (FEP) screening to determine if post-closure criticality must be included as an event in the 10,000-year regulatory evaluation. As such, the approach to modeling post-closure criticality presented in this report has been coordinated with the Sandia team responsible for FEP screening. The resulting analysis supports disposition of fissile materials in the CCO containing up to 380 FGE 239 Pu and expands conditions acceptable for disposal of fissile material in CCOs. This evaluation builds on the methodology of Saylor and Scaglione and Brickner, using the most recently available geomechanical data for CCO spacing under salt creep compaction scenarios provided by Reedlunn and Bean. The broad range of fissile material configurations analyzed in this report are intended to account for configurations that may occur during the post-closure disposal time period, and it also includes waste configurations that are not physically possible to support analysis of conditions that influence neutron fluence.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Regional Variation in Light-Duty Plug-in Electric Vehicle Emissions

Automobile electrification is viewed as one of the key requirements for deep decarbonization of transportation. However, the exact magnitude of decarbonization from switching from a combustion of petroleum-based fuels to grid-derived electricity is a complex issue. Variations in local grid mixes lead to differing carbon intensities of electricity in different regions. This complexity is compounded by geographical differences in vehicle characteristics. This analysis considers these geographic differences to produce a historical assessment of the fuel-cycle carbon emissions of plug-in electric vehicles (PEVs) in the United States from 2011 to 2021. We find that PEVs in the United States decreased in electricity-derived carbon intensity, from 187 grams per mile to 110 grams per mile from 2011 to 2021 due to improvements in the electric grid and vehicle efficiency. Through 2021, PEVs emitted a total of 13.6 million metric tons of greenhouse gas (GHG) emissions in the United States, including both emissions from electricity and gasoline, while driving a total of 100 billion miles. Of this total, 8.39 million metric tons was due to electricity consumption. Over the same distance, comparable gasoline vehicles would have emitted between 29 and 41 million metric tons of GHG, leading to a reduction of 15 to 27 million metric tons. Relative to national-level assessments that do not factor in this regional difference, these electric vehicles resulted in 13% greater reductions in GHG emissions than previously calculated. In the future, announced goals to further decarbonize the electricity sector will continue to reduce the emissions of PEVs, including reducing emissions rates for vehicles already on the road, further improving the benefits relative to the unchanging emissions of contemporaneous gasoline vehicles.

02 PETROLEUM↗

Modeling of Reactor Design and Optimization for Scale-Up of the Catalyxx Process for Ethanol Conversion to Higher Alcohol Biofuels

This report summarizes the results of a collaborative efforts between Oak Ridge National Laboratory (ORNL) and Catalyxx Inc. to investigate scale-up of Catalyxx’s Ethanol upgrading to higher alcohols process. The study was funded by the U.S. Department of Energy (DOE) Bioenergy Technologies Office (BETO) under CRADA (Cooperative Research and Development Agreement) No: NFE-20-08396. The project is part of the Direct Funding Opportunity (DFO) for Computational Science to Enable Bioenergy program which utilized computational toolsets developed by the Consortium for Computational Physics and Chemistry, a multi-laboratory consortium in BETO. The report here summarizes a packed-bed reactor modeling effort spanning the range from lab to industrial scale (from 4 gram to 5-ton catalyst beds), and examining reactor design, process optimization strategies, and suggested design and operating conditions for Catalyxx’s ethanol upgrading plants. The results in this report have been shared in monthly steering meetings and presentations are available in the shared data house owned by Catalyxx. The modeling effort helped to define optimum operation conditions for maximum alcohol selectivity and yield: i.e., temperature control scenarios ranging from adiabatic to isothermal, feed rate, pressure, and inlet H 2 /Ethanol ratio. The modeling results were verified at lab-(4 gram) and pre-pilot (4 kg) scales and has been used to evaluate a 5-ton packed-bed reactor and identify operating conditions to maximize the butanol yield. Special focus was given to understanding mass-transfer effects in the pre-pilot and pilot-scale reactors, over the domain of flow rate, pressure, feed composition, pellet size, shape, porosity, bed voidage, and reactor dimensions (i.e., length/diameter). Modeling was also used to evaluate innovative reactor design concepts such as water removal to improve alcohol selectivity and yield, and a reactor with an additional side inlet to facilitate quenching. These concepts were thoroughly explored, and potential benefits were disclosed. The results in this report are summarized and described qualitatively to protect the IP rights of Catalyxx. The details have been shared with the Catalyxx team in the regular steering meetings. At the end of the project, Catalyxx Inc. announced a successful demonstration of pilot scale operation in Seville, Spain.

02 PETROLEUM↗

Options for the Removal of Cesium and Strontium from Acidic Uranyl Sulfate Solutions from Molybdenum-99 Production: Part II The Effect of Sodium Carbonate Adjustment to pH 9 on Strontium Removal

A small laboratory-scale column process aimed at removing fission products from prototypical acidic sulfate solution wastes from a prototypical Mo-99 recovery process has been operated in a radioactive materials hood at Savannah River National Laboratory. This equipment has been operated with realistic concentrations of uranium (0.4 wt % 235 U), plutonium ( 239 Pu), neptunium ( 237 Np), non-radioactive surrogates of common fission products (including Cs and Sr) and two promising absorbents – AMP-PAN and CST R9120-B. The goal of this work was to demonstrate the removal and concentration of high specific activity isotopes which are expected to dominate the classification of the low-level waste from the production of 99 Mo. Both AMP-PAN and CST R9120-B are attractive absorbents for the removal of 137 Cs from an acidic sulfate waste stream. They do not provide a solution for the removal of 90 Sr from the acidic solutions. CST was shown to be useful at removing both Cs and Sr after adjustment of the acidic sulfate solution with sodium carbonate to pH 9. Limited removal of transuranic species and almost no removal of uranium was observed for CST R9120B absorbent. This could be important due to the relatively large amount of uranium expected to be present in such waste streams. The capacity of these absorbents for 137 Cs will likely be dependent on the Cs concentration in the solutions processed but loading in excess of 0.7 mg Cs per gram of CST absorbent while loading 0.14 mg Sr per gram of CST absorbent appears to be achievable from pH 9 carbonate solution.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Parametric Study of 239 Pu and 235 U Mass Equivalency in Spherical Geometries

In this technical document, parametric studies were performed to determine if a bounding mass equivalency can be used to simplify multi-material models in MCNP6 for criticality evaluations. The studies explored the simplification of MCNP6 models by substituting materials, particularly 239 Pu for 235 U. The initial hypothesis for the material simplification is based on the subcritical mass limits from the ANSI/ANS- 8.1 standard which states that for water reflected metal spheres the limits are 20.1 kg 235 U and 5.0 kg 239 Pu. Using those masses, it was hypothesized that a 20.1 kg sphere of 235 U and a 5.0 kg sphere of 239 Pu could be considered to have the same multiplication. Given that equivalency, 4kg 235 U could be modeled by 1kg 239 Pu (i.e., a mass ratio of 4:1). The parametric studies compare the materials 239 Pu and 235 U independently and in multi-material spherical models. Critical mass, critical thickness, critical mass ratio and critical thickness ratio values are presented as functions of inner radius. keff values are presented as a function of inner radius at different mass ratios and total masses. Results indicate that the conservative bounding mass equivalency is one. That is, if substituting 239 Pu for 235 U it should be done on a gram for gram basis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Biomimetic antibiotics based on amphiphilic peptoids and their self-assembly

Bacterial infections pose a serious threat to mankind. Inspired by antimicrobial peptides (AMPs) and their membrane-disruption mechanism, there is immense interest in the design and development of synthetic mimetics for antibacterial applications, overcoming the intrinsic drawbacks of AMPs (e.g. susceptibility to proteolytic degradation). Herein, by exploiting the self-assembly and pore-forming capabilities of sequence-defined peptoids, we discovered a new family of low molecular weight peptoid antibiotics that exhibited excellent broad-spectrum activity and high selectivity toward a panel of clinically significant Gram-positive and Gram-negative bacterial strains. Tuning peptoid sidechain chemistry and structure enabled us to tune the efficacy of antimicrobial activity and study the structure–activity relationship. These findings offer a novel approach to identify new families of antimicrobial peptoids and correlate the pore-forming capability of self-assembling peptoids with their antimicrobial activities. Because peptoids are highly robust and biocompatible, we exhibit these peptoid-based antibiotics will be significant for combating the emerging drug resistance.

59 BASIC BIOLOGICAL SCIENCES↗

Understanding and Harnessing the Robustness of Undomesticated Yarrowia lipolytica Strains for Biosynthesis of Designer Bioesters (Final Report)

This project seeks to elucidate and harness the exceptional robustness of novel and undomesticated Y. lipolytica isolates, which were identified from a genetic diversity screening for compatibility with bioenergy development. Bioenergy-relevant isolates were further developed as microbial platforms for efficient conversion of undetoxified biomass hydrolysates into designer bio-esters continuously recovered by solvent extraction. The project has three major goals. Goal 1. Elucidate and enhance the endogenous metabolism of Y. lipolytica for superior growth, sugar utilization, and lipid accumulation in undetoxified biomass hydrolysates under hypoxic conditions. Goal 2. Understand and enhance the underlying mechanism of exceptional tolerance of Y. lipolytica to organic solvents. Goal 3. Elucidate and rewire endogenous metabolism of the most robust Y. lipolytica strains for effective conversion of accumulating lipids to designer bio-esters. Significant progress has been made toward completing all research goals. We elucidated and optimized the robustness of Y. lipolytica by utilizing mixed C5 and C6 sugars in switchgrass hydrolysates (SGH) for lipid production (Aim 1). We conducted extensive omics analysis to investigate how genetic diversity among Yarrowia strains, derived from natural isolates or developed through adaptive laboratory evolution, influences lipid production when utilizing SGH. In Aim 2, novel mechanisms and underlying genetics were discovered that enabled Yarrowia strains to thrive in cultures containing high ionic liquid (IL) concentrations. Amongst other novel findings, it was found that sterols strengthened cell membranes to confer IL toxicity resistance, specifically via increased ergosterol content upon exposure to IL. In Aim 3, mechanistic studies elucidated how Y. lipolytica utilized intracellular lipids and alkanes/alkenes, leading to our discovery of novel enzymes and pathways for making short-chain esters. Most notably, thermostable chloramphenicol transferases were repurposed to function as alcohol acetyltransferases in Y. lipolytica, as well as the Gram-negative and Gram-positive bacteria Escherichia coli and thermophile Clostridium thermocellum, respectively.

09 BIOMASS FUELS↗

Characterization of Tank 9H Annulus Sample in Support of Residual Material Inventory Determinations

The Savannah River National Laboratory (SRNL) was requested by Savannah River Mission Completion (SRMC) to provide sample preparation and characterization of the Tank 9H annulus sample in support of Residual Material Inventory Determinations. One Tank 9H sample in three vials [HTF-9-25-13, HTF-9-25-14 and HTF-9-25-15], with each vial containing approximately 200 mL of the Tank 9H annulus salt solution, were delivered to the SRNL Shielded Cells for sample preparation and characterizations in February 2025. The density of the “as-received” solution contained in each of the three Tank 9H annulus sample vials were determined followed by a solid-liquid separation on each one using 0.45-micron Nalgene® nylon filter membranes. The resulting filtrates were combined to form the Tank 9H annulus sample with a total volume of about 600 mL. The combined wet solid fractions, about a total of 4.8 grams of salt material, remaining on the filter membranes were air-dried in the Shielded Cells for 72 hours. The total weight of the air-dried solids was 2.1 grams. These air-dried solids were washed with deionized water (DI water) at a phase ratio of 60 mL DI water/gram of solids to recover insoluble solids, if any. No visible or measurable quantity of insoluble solids were recovered after DI water washing of the air-dried solids because the air-dried solids completely dissolved in the DI water. The solid fraction-wash water was not combined with the 600 mL of the filtrate solution, and the resulting solution was not screened or analyzed for radionuclides. Aliquot sample volumes of the undiluted Tank 9H annulus sample were sent to the SRNL analytical services groups for radionuclides, elementals, anions and total mercury analysis by various methods including radiochemical separations/counting methods, inductively coupled plasma-atomic emission spectroscopy (ICP-AES), and Inductively Coupled Plasma Mass Spectroscopy (ICP-MS) and special preparations. All sample analyses were performed in triplicate. This report presents the analytical characterization results for the Tank 9H annulus sample. The results are also reported where analytical methods yielded additional analytes, other than those requested by SRMC. In the characterization of the Tank 9H annulus sample, the detection limits for all the analytes, as specified in the Technical Task Request (TTR) and Task Technical and Quality Assurance Plan (TTQAP), were met.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Chemical Recycling of Plastic Waste to Higher Value Lubricants

The aim of this project was to develop scalable methods to convert plastic waste to petrochemical-equivalent feedstocks and demonstrate their utility in lubricant base oil and wax applications. These objectives were partially accomplished, by scaling up the synthesis of platinum-on-strontium titanate catalysts to twenty gram batches, scaling up the conversion of plastic waste to twenty-five grams of plastic, producing high-melt waxes and characterizing their properties, and demonstrating the purification of high-melt waxes. High-melt waxes are one petrochemical-equivalent feedstock that can be made from plastic waste, consisting of a hard wax with a melt point above 65 C. They are used as ingredients in hot melt adhesives, coatings, and cosmetics. Producing a petrochemical-equivalent feedstock from plastic waste provides an advantage in lower carbon footprint and manufacturing cost, as the waste feedstock costs less than crude oil.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Improbability of Post-Closure Criticality in Compacted Criticality Control Overpacks after Room Closure at Waste Isolation Pilot Plant

As part of its periodic re-certification of the Waste Isolation Pilot Plant (WIPP), an operating repository in bedded salt for the disposal of transuranic (TRU) waste from atomic energy defense activities, the United States Environmental Protection Agency expects a re-evaluation of features, events, and processes, such as post-closure nuclear criticality. Although salt creep beneficially encapsulates the TRU waste in the closed WIPP repository, the spacing between an array of waste packages is disrupted as the salt creep closes disposal rooms and containers lose structural integrity. For most TRU waste, the possibility of post-closure criticality is exceedingly small either because the salt neutronically isolates TRU waste canisters or because closure of a disposal room from salt creep does not sufficiently compact the low mass of fissile material. The criticality evaluation was updated, however, because of the introduction of criticality control overpack (CCO) containers, which may dispose up to 380 fissile gram equivalent plutonium-239 in each container. The criticality potential is evaluated through high-fidelity geomechanical modeling of a disposal room filled with CCO containers during two representative conditions: (1) large salt block fall, and (2) gradual disposal room closure from salt creep. Geomechanical models of roof fall demonstrate three tiers of CCO containers are not greatly disrupted. Geomechanical models of gradual room closure from salt creep (without brine seepage and subsequent gas generation to permit maximum room closure) were used to predict irregular arrays of closely packed CCOs after 1000 years, when room closure has asymptotically approached maximum compaction. Models of spheres or cylinders with 380 fissile gram equivalent of plutonium (as oxide) at the predicted irregular compacted spacing demonstrate that an array of CCO containers is not critical when surrounded by salt and magnesium oxide, provided the mass of hydrogenous material shipped in CCO containers (usually plastics) is controlled or boron carbide (a neutron poison) is mixed with the fissile contents.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Leisingera sp. ANG59 & Pseudoalteromonas sp. JC28 Genomes Overview

The Hawaiian bobtail squid, Euprymna scolopes, has a symbiotic bacterial consortium in the accessory nidamental gland (ANG), a female reproductive organ that protects eggs against fouling microorganisms. To test the antibacterial activity of ANG community members, 19 bacterial isolates were screened for their ability to inhibit Gram-negative and Gram-positive bacteria, of which two strains were inhibitory. These two antibacterial isolates, Leisingera sp. ANG59 and Pseudoalteromonas sp. JC28, were subjected to further genomic characterization. Genomic analysis of Leisingera sp. ANG59 revealed a biosynthetic gene cluster encoding the antimicrobial compound indigoidine. The genome of Pseudoalteromonas sp. JC28 had a 14-gene cluster with >95% amino acid identity to a known bromoalterochromide (BAC) cluster. Chemical analysis confirmed production of known BACs, BAC-A/A′ (compounds 1a/1b), as well as two new derivatives, BAC-D/D′ (compounds 2a/2b). Extensive nuclear magnetic resonance (NMR) analyses allowed complete structural elucidation of compounds 2a/2b, and the absolute stereochemistry was unambiguously determined using an optimized Marfey’s method. The BACs were then investigated for in vitro antibacterial, antifungal, and nitric oxide (NO) inhibitory activity. Compounds 1a/1b were active against the marine bacteria Bacillus algicola and Vibrio fischeri, while compounds 2a/2b were active only against B. algicola. Compounds 1a/1b inhibited NO production via lipopolysaccharide (LPS)-induced inflammation in RAW264.7 macrophage cells and also inhibited the pathogenic fungus Fusarium keratoplasticum, which, coupled with their antibacterial activity, suggests that these polyketide-nonribosomal peptides may be used for squid egg defense against potential pathogens and/or fouling microorganisms. These results indicate that BACs may provide Pseudoalteromonas sp. JC28 an ecological niche, facilitating competition against nonsymbiotic microorganisms in the host’s environment.​

59 BASIC BIOLOGICAL SCIENCES↗

The multifaceted role of c-di-AMP signaling in the regulation of Porphyromonas gingivalis lipopolysaccharide structure and function

This study unveils the intricate functional association between cyclic di-3’,5’-adenylic acid (c-di-AMP) signaling, cellular bioenergetics, and the regulation of lipopolysaccharide (LPS) profile in Porphyromonas gingivalis, a Gram-negative obligate anaerobe considered as a keystone pathogen involved in the pathogenesis of chronic periodontitis. Previous research has identified variations in P. gingivalis LPS profile as a major virulence factor, yet the underlying mechanism of its modulation has remained elusive. We employed a comprehensive methodological approach, combining two mutants exhibiting varying levels of c-di-AMP compared to the wild type, alongside an optimized analytical methodology that combines conventional mass spectrometry techniques with a novel approach known as FLAT n . We demonstrate that c-di-AMP acts as a metabolic nexus, connecting bioenergetic status to nuanced shifts in fatty acid and glycosyl profiles within P. gingivalis LPS. Notably, the predicted regulator gene cdaR, serving as a potent regulator of c-di-AMP synthesis, was found essential for producing N-acetylgalactosamine and an unidentified glycolipid class associated with the LPS profile. The multifaceted roles of c-di-AMP in bacterial physiology are underscored, emphasizing its significance in orchestrating adaptive responses to stimuli. Furthermore, our findings illuminate the significance of LPS variations and c-di-AMP signaling in determining the biological activities and immunostimulatory potential of P. gingivalis LPS, promoting a pathoadaptive strategy. The study expands the understanding of c-di-AMP pathways in Gram-negative species, laying a foundation for future investigations into the mechanisms governing variations in LPS structure at the molecular level and their implications for host-pathogen interactions.

59 BASIC BIOLOGICAL SCIENCES↗

One fold, many functions—M23 family of peptidoglycan hydrolases

Bacterial cell walls are the guards of cell integrity. They are composed of peptidoglycan that provides rigidity to sustain internal turgor and ensures isolation from the external environment. In addition, they harbor the enzymatic machinery to secure cell wall modulations needed throughout the bacterial lifespan. The main players in this process are peptidoglycan hydrolases, a large group of enzymes with diverse specificities and different mechanisms of action. They are commonly, but not exclusively, found in prokaryotes. Although in most cases, these enzymes share the same molecular function, namely peptidoglycan hydrolysis, they are leveraged to perform a variety of physiological roles. A well-investigated family of peptidoglycan hydrolases is M23 peptidases, which display a very conserved fold, but their spectrum of lytic action is broad and includes both Gram- positive and Gram- negative bacteria. In this review, we summarize the structural, biochemical, and functional studies concerning the M23 family of peptidases based on literature and complement this knowledge by performing large-scale analyses of available protein sequences. This review has led us to gain new insight into the role of surface charge in the activity of this group of enzymes. We present relevant conclusions drawn from the analysis of available structures and indicate the main structural features that play a crucial role in specificity determination and mechanisms of latency. Our work systematizes the knowledge of the M23 family enzymes in the context of their unique antimicrobial potential against drug-resistant pathogens and presents possibilities to modulate and engineer their features to develop perfect antibacterial weapons.

Razew, Alicja↗

Aculeaxanthones A–E, new xanthones from the marine-derived fungus Aspergillus aculeatinus WHUF0198

Introduction Dimeric natural products are widespread in plants and microorganisms, which usually have complex structures and exhibit greater bioactivities than their corresponding monomers. In this study, we report five new dimeric tetrahydroxanthones, aculeaxanthones A−E ( 4−8 ), along with the homodimeric tetrahydroxanthone secalonic acid D ( 1 ), chrysoxanthones B and C ( 2 and 3 ), and 4−4’-secalonic acid D ( 9 ), from different fermentation batches of the title fungus. Methods A part of the culture was added to a total of 60 flasks containing 300 ml each of number II fungus liquid medium and culture 4 weeks in a static state at 28˚C. The liquid phase (18 L) and mycelia was separated from the fungal culture by filtering. A crude extract was obtained from the mycelia by ultrasound using acetone. To obtain a dry extract (18 g), the liquid phase combined with the crude extract were further extracted by EtOAc and concentrated in vacuo. The MIC of anaerobic bacteria was examined by a broth microdilution assay. To obtain MICs for aerobic bacteria, the agar dilution streak method recommended in Clinical and Laboratory Standards Institute document (CLSI) M07-A10 was used. Compounds 1−9 was tested against the Bel-7402, A-549 and HCT-116 cell lines according to MTT assay. Results and Discussion The structures of these compounds were elucidated on the base of 1D and 2D NMR and HR-ESIMS data, and the absolute configurations of the new xanthones 4−8 were determined by conformational analysis and time-dependent density functional theory-electronic circular dichroism (TDDFT-ECD) calculations. Compounds 1–9 were tested for cytotoxicity against the Bel-7402, A549, and HCT-116 cancer cell lines. Of the dimeric tetrahydroxanthone derivatives, only compound 6 provided cytotoxicity effect against Bel-7402 cell line (IC50, 1.96 µM). Additionally, antimicrobial activity was evaluated for all dimeric tetrahydroxanthones, including four Gram-positive bacteria including Enterococcus faecium ATCC 19434, Bacillus subtilis 168, Staphylococcus aureus ATCC 25923 and MRSA USA300; four Gram-negative bacteria, including Helicobacter pylori 129, G27, as well as 26,695, and multi drug-resistant strain H. pylori 159, and one Mycobacterium M. smegmatis ATCC 607. However, only compound 1 performed activities against H. pylori G27, H. pylori 26695, H. pylori 129, H. pylori 159, S. aureus USA300, and B. subtilis 168 with MIC values of 4.0, 4.0, 2.0, 2.0, 2.0 and 1.0 μg/mL, respectively.

Wu, Jun↗

Insights into the physiological and genomic characterization of three bacterial isolates from a highly alkaline, terrestrial serpentinizing system

The terrestrial serpentinite-hosted ecosystem known as “The Cedars” is home to a diverse microbial community persisting under highly alkaline (pH ~ 12) and reducing (Eh < -550 mV) conditions. This extreme environment presents particular difficulties for microbial life, and efforts to isolate microorganisms from The Cedars over the past decade have remained challenging. Herein, we report the initial physiological assessment and/or full genomic characterization of three isolates: Paenibacillus sp. Cedars (‘Paeni-Cedars’), Alishewanella sp. BS5-314 (‘Ali-BS5-314’), and Anaerobacillus sp. CMMVII (‘Anaero-CMMVII’). Paeni-Cedars is a Gram-positive, rod-shaped, mesophilic facultative anaerobe that grows between pH 7–10 (minimum pH tested was 7), temperatures 20–40°C, and 0–3% NaCl concentration. The addition of 10–20 mM CaCl 2 enhanced growth, and iron reduction was observed in the following order, 2-line ferrihydrite > magnetite > serpentinite ~ chromite ~ hematite. Genome analysis identified genes for flavin-mediated iron reduction and synthesis of a bacillibactin-like, catechol-type siderophore. Ali-BS5-314 is a Gram-negative, rod-shaped, mesophilic, facultative anaerobic alkaliphile that grows between pH 10–12 and temperatures 10–40°C, with limited growth observed 1–5% NaCl. Nitrate is used as a terminal electron acceptor under anaerobic conditions, which was corroborated by genome analysis. The Ali-BS5-314 genome also includes genes for benzoate-like compound metabolism. Anaero-CMMVII remained difficult to cultivate for physiological studies; however, growth was observed between pH 9–12, with the addition of 0.01–1% yeast extract. Anaero-CMMVII is a probable oxygen-tolerant anaerobic alkaliphile with hydrogenotrophic respiration coupled with nitrate reduction, as determined by genome analysis. Based on single-copy genes, ANI, AAI and dDDH analyses, Paeni-Cedars and Ali-BS5-314 are related to other species (P. glucanolyticus and A. aestuarii, respectively), and Anaero-CMMVII represents a new species. The characterization of these three isolates demonstrate the range of ecophysiological adaptations and metabolisms present in serpentinite-hosted ecosystems, including mineral reduction, alkaliphily, and siderophore production.

59 BASIC BIOLOGICAL SCIENCES↗

Magnetic nanostructures and composites for millimeter wave absorption

A product includes a nanostructure having a core and a shell. The core has a coercive field of at least 3 kOe and the shell has a saturation magnetization of at least 50 emu per gram. A product includes a nanostructure having a core and a shell. The shell has a coercive field of at least 3 kOe and the core has a saturation magnetization of at least 50 emu per gram. A method includes forming core/shell nanostructures and forming millimeter wave absorbers including the core/shell nanostructures and a support structure.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Irradiated Low-Enriched Uranium Fuel Measurements with a Gamma-Ray Scanning System

A gamma-ray scanning system was designed to perform post-irradiation measurements of nuclear fuel at Idaho National Laboratory (INL). The system is composed of a coaxial high-purity germanium (HPGe) detector, a collimator, and mechanical positioning stages that translate the fuel sample across the front of the collimator. A Monte Carlo N-Particle code simulation of the system and the fuel were created with vendor-supplied design specifications, dimensional measurements, and x-ray radiographs of the HPGe detector as well as all available fuel specifications. Benchmark measurements were performed by scanning an irradiated fuel rodlet containing eight pellets of 0.74% enriched UO2 in zirconium alloy. This fuel rodlet was part of the Static Environment Rodlet Transient Test Apparatus (SERTTA) testing campaign in the Transient Reactor Test Facility (TREAT). These results were compared to simulated spectra to help characterize the detector model and establish fidelity. A goal of the system is to determine the number of fissions per gram of UO2 in the fuel. This paper documents the modeling of the system and the calculation of the number of fissions per gram along the axial length of the SERTTA-C rodlet.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗