Search NASA⌕ Search

SEARCH · Search NASA

Results for “Gas barrier”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Integrated TBC/EBC for SiC Fiber Reinforced SiC Matrix Composites for Next Generation Gas Turbines (Final Report)

In this ambitious project, a significant challenge preventing widespread use of ceramic matrix composites in hot section components of gas power generating turbines was addressed. Hot section components made from SiC fiber reinforced SiC matrix composites (SiC/SiC composites), have the potential to achieve a combined cycle energy efficiency of above 65%. To achieve this efficiency, the temperature of the combustion gases on the turbine component surface is expected to reach as high as ~1700ºC (3100ºF). However, SiC/SiC composites suffer from volatilization at high temperature under high velocity steam environment – typical in a turbine hot chamber. This integrated collaborative project, between two research groups at Clemson University and a team of engineers and scientists at GE Gas Power, focused on design, fabrication and evaluation of a new graded environmental barrier coating. Using the excellent compositional tailorability of polymer derived ceramics (PDCs), we developed an integrated EBC/BC that smoothly transitions from bottom SiC/SiC bond interface to hermetic sesquioxide (Y 2 O 3 ) top surface. This smooth compositional transition avoided the sharp CTE mismatch at interfaces to greatly reduce the thermal stress. The developed EBC is compatible with and bonds well with the bond coat that GE uses. The top hermetic oxide surface ensures low oxygen transportation and volatilization rates under the high velocity steam environment. The graded microstructure with increasing sesquioxide concentration also decreases the amount of Si and C elements near the top hermetic sesquioxide layer. Coatings made using a process suitable for manufacturing – atmospheric plasma spraying was demonstrated. The microstructure of coatings made using this process were fully characterized. Finally, the performance of these coatings was investigated under the most demanding conditions for this application. Specifically, high temperature, high velocity steam exposure; thermal shock test; and thermal cycling tests. The graded coatings performed exceptionally well in all these tests. Specific suggestions for future development in this area have also been identified. In addition to the excellent technical progress, this project helped initiate a robust collaboration between the research groups at Clemson and GE Gas Power. It also provided a high-quality learning and mentoring opportunity for the three post-doctoral research associates and two UG students at Clemson University who worked on this project. All proposed tasks, sub-tasks were completed, and all milestones achieved.

03 NATURAL GAS↗
DOE OSTI2023

Apparatus for a laser welding system

A laser welding system for welding a component and reducing defects in the weld by ensuring uniform, laminar gas flow over a process area of the system. The laser welding system comprises a laser for welding the component, a platform for supporting the component, an enclosure surrounding the platform, a first actuatable barrier, a second actuatable barrier, an actuator, and a controller. The enclosure includes a plurality of walls, one of the walls having an inlet and another wall having an outlet. The inlet and outlet each having an opening having a cross-sectional area for letting gas flow through. The first and second barriers are configured to modify the cross-sectional areas of the openings when actuated. The actuator is configured to actuate the barriers, and the controller is configured to direct the actuator to actuate the barriers so that the cross-sectional area of the first opening is larger than the cross-sectional area of the second opening so that a pressure at the inlet is greater than a pressure at the outlet.

Sartin, Bryan↗
DOE OSTI2024

Design and Evaluation of Environmental Barrier Coatings for Protection of Ceramic Matrix Composites in Hydrogen-Based Turbines

This presentation at the 2024 FECM Spring Project Review Meeting summarizes ongoing work at NETL aimed at enabling the use of ceramic matrix composite (CMC) materials in next-generation high-efficiency power generation turbines fueled by hydrogen, natural gas, or other fuels. The work broadly involves three aspects (1) phase-field damage modeling of CMCs and the environmental barrier coatings (EBCs) used to protect them (2) computational design of new and improved EBCs and (3) performance testing of EBCs using a novel gas turbine combustion simulation rig developed at NETL. An overview on current status and next steps for each aspect of the project are presented.

ceramic matrix composite (CMC)↗
DOE OSTI2025

Melting temperature, emissivity, and thermal conductivity of rare-earth silicates for thermal and environmental barrier coatings

In recent years, rare-earth silicates have become the industry standard for coating state-of-the-art SiC ceramic matrix composite (CMC) gas turbine engine components, due to their low volatility, high melting point, and thermal shock resistance. Current research is focused on designing rare-earth silicate based thermal-environmental barrier coatings (T/EBCs) with improved resistance to CMAS (CaO-MgO-Al 2 O 3 -SiO 2 ), steam, and crack formation, while maintaining high temperature performance and stability. Here, in this work we compare the high temperature performance of a variety of single and multi-component rare-earth mono- and disilicates (MS, DS) and rare earth apatites by measuring their melting points and spectrally averaged visible emissivities using laser heating and radiation pyrometry. We also report room temperature thermal conductivity measured by time-domain thermoreflectance (TDTR).

Environmental barrier coatings↗
DOE OSTI2020

In situ characterization of foreign object damage (FOD) in environmental-barrier-coated silicon carbide (SiC) ceramic

Environmental barrier coatings (EBCs) protect advanced ceramics and ceramic matrix composites (CMCs) from oxidation and corrosion in gas turbine engine environments. Foreign object damage (FOD), where debris impact the protective coatings, is a critical hazard which limits the turbine durability. Despite previous efforts to understand FOD in EBCs, a detailed understanding of the fundamental transient damage mechanisms is still lacking. In the current work, the real-time FOD behavior of a Mullite / Silicon EBC was visualized via a dynamic synchrotron X-ray source in phase contrast imaging (PCI) configuration. Prior to the in situ FOD experiments, the microstructure and composition of the coating were respectively characterized using a scanning electron microscope (SEM) and X-ray diffraction (XRD). The variation in the properties of the debris was modeled by ~ 1.5 mm diameter Partially Stabilized Zirconia (PSZ) and Silicon Nitride (Si 3 N 4 ) spheres. A modified light-gas gun setup, synchronized with the X-ray beam, was used to propel the projectiles at velocities ranging between 300 and 355 m·s -1 . Coated samples were impacted under a fully backed support configuration and at normal incidence. Coating penetration and delamination, as well as projectile deformation at the bond coat resulted for FOD by PSZ spheres. Comparatively, projectile fracture, with subsequent rebound of fragments, as well as complete coating penetration and delamination at the substrate interface occurred for FOD by Si 3 N 4 spheres. It should be noted that only cone cracking was observed for FOD by PSZ spheres while back surface cracking was present for both projectile types. Qualitative understanding of the driving forces for the observed damage mechanisms were provided.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Phase-field modeling of thermally-grown oxide and damage evolution in environmental barrier coatings

Silicon carbide-based ceramic matrix composites protected by environmental barrier coatings (EBCs) present a promising materials solution for next-generation gas turbines. Developing more robust and efficient EBCs is therefore of significant technological importance. During the service in high-temperature oxidative environments, there is a thermally grown oxide (TGO) layer, spontaneously formed in the EBC system. TGO is recognized as a critical factor for the degradation and failure of EBCs, yet the detailed mechanisms of TGO growth and its effect on EBC failure remain unclear. In this study we develop a comprehensive chemo-mechano-phase-field model to simulate growth of the TGO in EBCs, factoring in creep and deformation, and especially the cracking behaviors. The volume expansion due to TGO growth and the resulting large inelastic deformation are addressed by using our recently developed, so-called incremental realization of inelastic deformation (IRID) algorithm, in combination with an adapted Hu-Chen spectral solver for elasticity. Simulations of TGO growth are performed considering different growth modes of TGOs determined mainly by the ratio of oxidant permeability in the topcoat to that in the TGO itself. Large-scale three-dimensional (3D) simulations are performed to model the formation of interconnecting vertical/channel cracks (often called ‘mud cracks’). The simulated crack morphology are in excellent agreement with the experimental observations from the literature. The simulations also provide insights into the cracking of EBCs and its dependence on the structure and constituent properties of the coating system. Furthermore, these results demonstrate the developed damage model can be a useful tool for design of more durable EBCs.

Cracking↗
DOE OSTI2025

Turbulence suppression at extreme plasma densities on DIII-D and EAST

Recent high-poloidal-beta (high-βP) experiments on DIII-D and EAST have made coordinated breakthroughs for high confinement quality at high density near the Greenwald limit. Density gradient amplification of turbulence suppression at high βP can explain both of these achievements. Experiments on DIII-D have achieved Greenwald fraction (fGr = line-averaged density/Greenwald density) above 1 simultaneously with normalized energy confinement (H98y2) around 1.5, as required in fusion reactor designs but never before verified in tokamak experiments with the divertor configuration. A synergy between increased H98y2 and fGr is observed with strong gas puffing, due to the build-up of an internal transport barrier at large radius in the temperature and density channels. Transport simulations reveal that the favorable trend of reduced turbulent energy transport at higher density is only expected when increasing the density gradient at high local safety factor and high β, thus at high βP to ensure strong α-stabilization. These conditions are crucial to many conceptual designs for steady-state reactors. New experiments on EAST have nearly doubled the ion temperature at fGr ∼ 0.9, consistent with predict-first modeling results based on the same physics revealed from the DIII-D analysis. All previous EAST long-pulse H-modes have Ti ≪ Te near plasma axis. Transport modeling indicates that the profiles are limited by ion-temperature-gradient modes at mid-radius. The modeling also suggested potential solutions, including reducing magnetic shear, enhancing density gradients, and higher impurity concentration. Following this guidance, EAST experiments directly show a strong enhancement of Ti achieved with a combination of a second plasma current ramp-up, a density gradient increase, and a Zeff perturbation by a short pulse (100 ms) of impurity injection, as predicted by the earlier modeling.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Summary of UMI Chemical Work

Our initial work for the Urban Modeling Integration (UMI) project was to validate the QUIC model dense gas dispersion of chlorine advection up a ramp. The validation task was to use QUIC to model an experiment done in a wind tunnel. Naturally the QUIC model uses a slumping cylindrical model where inside the cylinder the gas is treated as dense but outside ideal. In trying to validate using the wind tunnel experiment, due to the scale of the wind tunnel experiment and ramp, The model formed a very clear, discrete, concentration barrier at the edge of the cylinder that likely doesn’t line up well with the real dense gas advection/diffusion. This effect is much less noticeable at a larger scale such as an instantaneous release of a 25 ton tank.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Dynamic separation of gases using microsieves

Separation of light weight molecules, such as nitrogen, argon, and oxygen, from heavier compounds can have significant impacts on energy capture, environmental monitoring, or isotopic applications. Large-scale gas separation techniques, like gas centrifugation and membrane mitigation, can be problematic as they impart tremendous energy and induce high mechanical stress onto the instrumentation. Microsieves, also known as micronozzles or microfunnels, are developed to create physical barriers to separate specific isotopes and gases. Separation is achieved using a converging and diverging micronozzle to impose supersonic gas flow around a curved wall, and it has been used for the separation of heavy actinide isotopes in low weight gas as well as separation of low weight gas compositions of nitrogen and argon back in 1900s. However, systematic reviews of this unique technology are lacking. The application of the Laval style nozzle, which has a converging/diverging entrance fundamental to the micronozzle, is included in this review due to its importance in industrial applications in uranium (U) isotope refinement. Using advanced computational fluid dynamic (CFD) simulations, the extent of gas separation can be modelled. Herein, we first examine the literature and survey recent advances on fabrication techniques for creating curved micronozzles, methods and separation principles used to design devices. Furthermore, we then follow with highlights of CFD simulations applied to evaluate the separation effects using microsieves. Finally, identification of the gap and recommendation for future development and applications are suggested for using intrinsic molecular features and fluidic dynamics in formulating separation strategies.

30 Microfluidics↗
DOE OSTI2020

Impact damage of narrow silicon carbide (SiC) ceramics with and without environmental barrier coatings (EBCs) by various foreign object debris (FOD) simulants

The leading and trailing edges of turbine airfoils are highly susceptible to impact by foreign object debris (FOD) entrained in the gas stream of turbine engines. In this study, a narrow specimen geometry is implemented to study the FOD impact behavior of low curvature airfoil edges. Silicon carbide (SiC) ceramic specimens with and without an environmental barrier coating (EBC) are used as target materials. The EBC consists of an air plasma sprayed mullite topcoat (~ 166 µm) and silicon bond coat (~ 58 µm). Spherical (∅ 1.5 mm) FOD simulants of silicon nitride (Si3N4), partially stabilized zirconia (PSZ), and steel are used as impactors. Additionally, a modified gas gun is used to generate impact damage at normal incidence and velocities ranging between 300 to 400 m/s. In situ phase contrast X-ray radiographs, which render 2D representations of the internal transient damage, are captured during the impact experiments. Impactor hardness and toughness are found to primarily influence damage in the coating. Relative to wide specimens, the narrow specimens experience a greater level of cracking and this is postulated to result from reduced self-confinement. Irrespective of specimen geometry and impactor material type, limited cracking (i.e. enhanced shielding) is observed for the coated condition.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dry air cyclic oxidation of mixed Y/Yb disilicate environmental barrier coatings and bare silica formers

Here mixed Y and Yb disilicate coatings (Y/Yb)DS have been proposed as dual function thermal and environmental barrier coatings (EBCs) for protecting SiC-based ceramic matrix composites in gas-turbine environments. As an initial step, the 1350 °C dry air cyclic oxidation of atmospheric plasma sprayed (Y 1.2 /Yb 0.8 )DS and ytterbium disilicate/ytterbium monosilicate (YbDS/YbMS) EBCs deposited onto Si bond coatings was compared. As a baseline for evaluating EBC oxidant permeability, the dry air cyclic oxidation scale growth rates for bare silica formers (SiC, Si) were also measured and were consistently higher than rates previously measured after isothermal oxidation. Regarding Si bond coat oxidation rates underlying (Y/Yb)DS and YbDS/YbMS EBCs, the thinner silica scale formed under the thinner and denser (Y/Yb)DS coatings suggested a lower oxidant permeability than YbDS/YbMS. After 500 1-h cycles, the (Y/Yb)DS coating was comprised of only the β-polymorph disilicate and minor amounts of the X-2 phase monosilicate phase. Negligible differences in oxidation kinetics for (Y/Yb)DS coatings over the 90 – 240 µm thickness range were observed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Investigation of the structure and chemical nature of Pd fission product agglomerations in irradiated TRISO particle SiC

Tristructural-isotropic (TRISO)-coated fuel particles are used in high-temperature gas-cooled nuclear reactors. Although the polycrystalline 3C-SiC layer acts as the main barrier to fission product release, post-irradiation examinations have shown that certain metallic fission products are found outside of the TRISO coated particle, with no observable micro-cracks or other mechanical failure feature. In this study, an atomic resolution transmission electron microscopy investigation of a SiC layer of a neutron irradiated (19.38% fissions per initial metal atom average burnup; 1072°C time-averaged temperature) TRISO-coated particle from the first advanced gas reactor experiment at Idaho National Laboratory containing mainly Pd and U was conducted. The fission product Pd was found to be present at dislocation cores associated with twins, stacking faults, and their intersections. The Pd present at the dislocation cores were bonded to Si, suggesting that the diffusion of Pd along the SiC dislocation cores involves the formation of Pd-Si bonds. Evidence of single atom grain boundary migration was also found. Fission product agglomerations at grain boundaries most likely consist of a random solid solution containing Si-FP, Si-C, and C-C type bonding arrangements. No difference in the Si- or C-bonding environment is found for the unoccupied grain boundary adjacent to a fission product agglomeration compared to the bulk SiC.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

A comparative analysis of numerical approaches for the description of gas flow in clay-based repository systems: From a laboratory to a large-scale gas injection test

There is nowadays a consensus among many countries that geological disposal is a favourable solution for the long-term management. Although different host formations and different barrier systems are under consideration around the world, clay-based materials form an important component for waste isolation in most national programmes. Hence, a good comprehension of the effect of gas flow on the hydro-mechanical behaviour of clay-based soils is essential, both at laboratory and field scale. Task B under the international cooperative project DECOVALEX-2023 has recently shown that, after some enhancement, models can be employed to reproduce laboratory scale tests, even with different sample geometries 37 . However, further work is required to understand whether they can be applied to simulate a large-scale experiment. Up-scaling of models for the advective transport of gas through clay-based low permeable material presents a number of problems related to the difficulty in obtaining consistent hydrogeological parameters and constitutive relationships at both laboratory and field scale. Based on a unique dataset from a large-scale gas injection test (Lasgit) performed at the Äspö Hard Rock Laboratory (Sweden), Task B within DECOVALEX-2023 has explored the refinement of these numerical strategies applied to the simulation of gas flow. Work performed within the task reveals that codes do not need to be substantially modified from the laboratory models to reproduce full-scale tests: indeed, model parameters calibrated and validated at laboratory scale have been applied to predict field scale gas flow at Lasgit, including peak gas pressure and injected cumulative gas volume. By means of (1) the introduction of interfaces between blocks to reflect the experimental configuration and the (2) adjustment of some parameters (e.g., higher permeability), the updated models are able to represent most of the key features observed in the experimental data, even at a large scale.

Tamayo-Mas, E↗
DOE OSTI2021

Effect of CMAS viscosity on the infiltration depth in thermal barrier coatings of different microstructures

Calcium magnesium aluminum silicate (CMAS) is one of the leading concerns for the gas turbine industry. The effects of CMAS viscosity and the coating microstructure on CMAS infiltration depth were explored by conducting a time dependent interaction study. Three CMAS compositions were used from literature, and their viscosities predicted through FactSage viscosity module were drastically different. The interaction was carried out on three different TBCs synthesized using the solution precursor plasma spray process (SPPS): two of the TBCs were made of yttrium aluminum garnet (YAG) having different microstructures that promote different modes of CMAS infiltration, and one TBC was made of gadolinium zirconate (GZO). All samples had stress relieving vertical cracks and different intensities of horizontally banded porosity, (inter pass boundaries IPBs). A concentration of 100 mg/cm 2 of CMAS was applied on the TBCs which were then subjected to a 5-minute interaction at 1300 °C. Samples were analyzed using scanning electron microscopy (SEM), electron dispersive X-ray spectroscopy (EDXS), and transmission electron microscopy (TEM). Low viscosity CMAS readily penetrated the TBCs while more viscous CMAS showed less penetration. The depth of CMAS infiltration depended on the coating microstructure. In the YAG with IPBs, the CMAS spread horizontally in the IPBs before infiltrating deeper, resulting in reduced infiltration depth compared to other samples in spite of having wider vertical cracks. TEM and EDXS analysis were performed to investigate the phases present in the CMAS-TBC interaction region in YAG. Two regions were chosen, the top TBC surface in direct contact with the sea of CMAS, and the region at the CMAS penetration ended within the coating. Finally, the results showed that no secondary phases like apatite were observed in YAG, thus it can be concluded that the arrest of CMAS happened solely because of CMAS viscosity and the short infiltration time.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Minimized aging of isocyanurate-based rigid cellular foams for buildings through tailored barrier facers and optimized formulation

The thermal resistivity (h·ft 2 ·°F/Btu/in.) of closed-cell rigid foam insulation materials significantly decreases over time. Diffusion-tight facers are designed to significantly enhance initial thermal resistivity and long-term thermal performance by preventing gas diffusion into the foam cells and inhibiting the escape of low thermal conductivity blowing agents. In addition to the gas diffusion property of the facer film, adhesion between the foam and the facer is crucial for achieving diffusion-tight bonding. Here, this study addresses the challenge of thermal aging by investigating how facer film properties and foam formulation influence the durability of thermal performance. A systematic evaluation was conducted to understand the effects of polymeric barrier films, surface treatments, facer coverage, and foam matrix rigidity on thermal resistivity over time. Key findings reveal that diffusion-tight facers, particularly those with metallized layers and compatible heat seal layers, significantly reduce gas exchange and improve foam-facer adhesion. The optimized system, incorporating barrier facers and a tailored polyisocyanurate foam formulation, achieved initial and aged thermal resistivity values after 200 days of approximately 8.3 and 7.4 h ft 2 ·°F/Btu/in., respectively representing only a 10 % reduction compared to a 17 % reduction observed in control samples without facers. Notably, polyurethane spray foams with facers exhibited only a 4 % reduction in thermal resistivity, compared to a 23 % decrease in control samples, demonstrating nearly six times better retention of thermal performance. This innovative facer technology presents a promising solution for reducing energy costs and represents a significant advancement in optimizing energy management for building envelopes in future technologies. This technology can also be adapted for other applications that necessitate the preservation of long-term thermal performance.

Wanasinghe, Shiwanka Vidarshi [Oak Ridge National ↗
DOE OSTI2020

A Thin Alumina Film as a Tritium Adsorption Inhibitor for Stainless Steel 316

The effect of a thin alumina coating on stainless-steel 316 (SS316) samples on tritium adsorption and transport are discussed. Compact films of alumina were produced on the surfaces of pristine SS316 samples using an atomic layer deposition (ALD) technique. Subsequently, these samples were exposed for 24 hours to a deuterium-tritium gas mixture (P T =0.5 atm, 25°C). A combination of methods including selective-etching and programmed thermal desorption were employed to assess both, the depth profile of the tritium concentration in the sample and the total quantity of tritium absorbed respectively. Tritium was quantitatively determined through the measurement of beta radioactivity using liquid-scintillation counting techniques. Data suggest that SS316 with a thin film of alumina reduces the total tritium uptake by ~25% relative to uncoated samples. Significantly, such films appear to reduce, by a factor of 200, tritium diffusion into SS316 and therefore constitute an effective barrier against tritium transport. This observation is of practical importance for tritium and, generally, reactive gas handling.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Temperature Inhibition of Plasma-Driven Methane Conversion in DBD Systems

Low-temperature non-thermal plasmas produce highly reactive chemical environments made up of electrons, ions, radicals, and vibrationally excited molecules. These reactive species, when combined with catalysts, can help drive thermodynamically unfavorable chemical reactions at low temperatures and atmospheric pressure. The conversion of methane (CH 4 ) to produce other value-added chemicals is a good model system because of its applicability to a wide range of industries. To effectively create these plasma catalytic systems, a fundamental understanding of the plasma-phase chemistry alone is imperative. While there have been many studies on methane plasmas and how certain operating conditions (i.e., gas composition and power) affect the plasma, there is limited understanding on how changing bulk reaction temperature affects the plasma properties and ensuing plasma chemistry. Here, in this work, we use a dielectric barrier discharge to investigate the effects of temperature on the reaction chemistry and the plasma’s electrical properties in various methane-gas mixtures. Results show that increasing temperature leads to a reduction in methane conversion as well as changes to both the gas and dielectric material pre-breakdown, which manifests itself in temperature-dependent electrical properties of the plasma. Experiments at various temperatures and power show a positive correlation between key electrical plasma properties (average charge and lifetime per filament) and the measured methane conversion as a function of temperature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

From Well Log to Formation Model: A Novel Laboratory Calibrated Methodology with Demonstration

This work demonstrates how the characterization and modeling of both elastic and creep properties are essential to describe zones in layered rock formations as either low-stress targets for stimulation or high-stress barriers to fracture growth. Prediction of fracture height is critical for designing stimulation operations in oil and gas wells. Ideally, fractures are placed in target zones which will produce hydrocarbons and should not propagate into zones expected to be unproductive or to produce unwanted fluids such as water which in turn must be treated and/or disposed. The essential task in designing stimulation plans is predicting which zones have low horizontal stresses and which will be high-stress barriers to fracture growth. Despite this importance, there are gaps in current knowledge and a complete workflow from laboratory characterization to a finite element model which includes time dependent rock deformation is required. While the research and methodology presented here also have application to CO 2or hydrogen storage, wastewater injection, and geothermal applications, the focus will be on hydrocarbon extraction. This thesis presents the results of a characterization-to-prediction workflow for the Caney shale, which is an emerging hydrocarbon resource in Oklahoma, USA. It begins with an investigation to enable critical evaluation of the Caney zonation into nominally “brittle” and “ductile” zones based on properties observed from well logs. It shows none of the zones are consistently “brittle” or “ductile” mechanical behavior based on the variety of definitions of these terms. However, the nominally ductile zones are weaker and more prone to creep. A laboratory investigation of samples including strength, elastic, and creep properties, is then used in a finite element model of stress evolution. The model includes both elastic deformation and viscoplastic creep. Results predict the least creep-prone layers to have the lowest horizontal stresses, therefore comprising hydraulic fracturing targets. The most creep-prone layers attain a horizontal stress similar to the vertical stress and therefore are predicted to be high stress barriers to hydraulic fracture stimulation. In addition to defining stimulation target intervals, the model shows how as tectonic strain rate increases, there is a transition from creep-dominated stresses to stresses dominated by elasticity.

Benge, Margaret↗