Search NASA⌕ Search

SEARCH · Search NASA

Results for “Gas cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Gas Generation in Lithium Cells with High-Nickel Cathodes and Localized High-Concentration Electrolytes

High-nickel layered-oxide cathodes (LiNi x Mn y Co 1-x-y O 2 , x ≥ 0.8) exhibit high capacities, but also experience rapid capacity fade during cycling, and are susceptible to heat generation and gas release. Advanced electrolytes, such as localized high-concentration electrolytes (LHCE), substantially stabilize the cathode during cycling and have lower flammability than conventional electrolytes, but gas generation with these electrolytes is yet to be assessed. We demonstrate here that gas generation from a high-nickel cathode in an LHCE is half as much as in a conventional electrolyte at 4.4 V. The gas generation in LHCE is further reduced at 4.3 V, but the LHCE generates a similar amount of gas as the conventional electrolyte at 4.6 V. Neither electrolyte can prevent gas generation after cycling; cathodes after 200 cycles generate similar amounts of gas as pristine cathodes during high-voltage hold. Finally, it is shown that in both electrolytes, oxygen from the cathode lattice plays a critical role in gas generation.

25 ENERGY STORAGE↗
DOE OSTI2020

Requirements and Conceptual Design of Off-gas Systems for the Reprocessing of Metallic Fuels

An assessment has been conducted to determine how key regulations regarding volatile radionuclide emissions to the atmosphere may apply to the off-gas streams associated with electrochemical reprocessing. The scope of this assessment was based upon a generic electrochemical reprocessing scheme with a throughput rate of 200 MTIHM/y applied to metallic fuel discharged from a sodium fast reactor (SFR), but the findings are able to be translated to other advanced nuclear scenarios as merited. Air dispersion modeling was performed using the EPA CAP-88 model and evaluated the uncontrolled decontamination factors (DFs) that would be required to achieve regulatory compliance with the dose-based limits set forth by EPA regulation 40 CFR 190.10(a). These DFs were compared to those required by fuel cycle–based limits set forth by EPA regulation 40 CFR 190.10(b). Two theoretical sites with disparate climatological conditions were selected for air dispersion modeling (Idaho and Tennessee). The radionuclides modeled included 3 H, 85 Kr, 129 I, and selected alpha-emitting transuranic isotopes (referred to here as 239 Pu-TRU <1y ). It was found that the fuel cycle-based limits in 40 CFR 190.10(b) are most restrictive for 85 Kr and 239 Pu-TRU <1y , with DFs of 3 and 6.1E+09, respectively. The dose-based limit as derived from 40 CFR 190.10(a) could require mitigation of tritium in some scenarios, with an estimated DF of about 3 for the reference scenarios. The fuel cycle-based limit for 129 I resulted in a DF of about 240 for the reference scenario. The need for iodine mitigation based on dose to the public depended upon the physical form of iodine as either particulate or vapor-phase species. Emission of iodine from the facility as a vapor necessitated DFs of about 2 but emission as a particulate would require DFs >6,000 to meet thyroid dose-based limits. Effects of physical form on needed iodine mitigation are significant, but the understanding of speciation of iodine both during electrochemical reprocessing and after release to the atmosphere is limited. The electrochemical processing unit operations were evaluated to identify potential release points for the volatile radionuclides and to assess the potential for retention of the radionuclides within the process (thus decreasing the need for mitigation). Mitigation strategies for 3 H, 85 Kr, 129 I, and 239 Pu-TRU <1y were identified. In all cases, there are reasonably achievable pathways to regulatory compliance, although in some cases additional R&D is merited to verify the chemical speciation of these isotopes and to develop and demonstrate potential treatment technologies for this application. Whether or not additional off-gas controls (beyond common operations such as HEPA filtration and oxygen and moisture control) are needed for any of these regulated or volatile radionuclides depends on the (a) type of facility (NRC-regulated or DOE), (b) used fuel process rate, (c) used fuel burnup and composition, (d) speciation and retention of volatile radionuclides in the process and in the cell gas cleanup system, (e) site-specific parameters such as location, meteorology, stack height, and site boundaries, and (f) levels of conservatism and safety factors used in assessing compliance to air emissions regulations. Performance of this assessment revealed several areas where information is lacking or additional research is required in order to better determine if or what kinds of off-gas control might be needed. First, and most significantly, the understanding of the chemical speciation and physical form and partitioning of iodine during electrochemical processing operations is lacking and prevents the ability to accurately assess the potential iodine mitigation requirements. Future research in this area should be multifaceted and include thermodynamic modeling of iodine speciation in different process steps, experiments to quantify the kinetics of vapor-phase and melt-phase transitions, bench-scale experiments to determine the potential chemical and physical form of iodine emissions from the electrorefining process, and verification of iodine behavior with experiments utilizing operational facilities. Similarly, an improved understanding of iodine behavior in the environment after release from the facility stack will be required to refine dose estimations, as particulate and vapor-phase emissions result in significantly different doses to the MEI.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1994

New Remote Gas Sensor Using Rapid Electro-Optical Path Switching

Innovative gas filter correlation radiometer (GFCR) features nonmechanical switching of internal optical paths. Incoming radiation switched electro-optically, by means of polarization, between two optical paths, one of which contains correlation gas cell while other does not. Advantages include switching speed, 2 to 3 orders of magnitude faster than mechanical techniques, and high reliability. Applications include regional studies of atmospheric chemistry from either manned or unmanned aircraft as well as satellite studies of global distributions, sources and sink mechanisms for key species involved in chemistry of troposphere. Commercial applications: ability to survey many miles of natural gas pipelines rapidly from aircraft, pinpointing gas leaks by measuring methane at 2.3 micrometers.

Sachse, G. W.↗
NASA NTRS2015

Pressure Monitoring Using Hybrid fs/ps Rotational CARS

We investigate the feasibility of gas-phase pressure measurements at kHz-rates using fs/ps rotational CARS. Femtosecond pump and Stokes pulses impulsively prepare a rotational Raman coherence, which is then probed by a high-energy 6-ps pulse introduced at a time delay from the Raman preparation. Rotational CARS spectra were recorded in N2 contained in a room-temperature gas cell for pressures from 0.1 to 3 atm and probe delays ranging from 10-330 ps. Using published self-broadened collisional linewidth data for N2, both the spectrally integrated coherence decay rate and the spectrally resolved decay were investigated as means for detecting pressure. Shot-averaged and single-laser-shot spectra were interrogated for pressure and the accuracy and precision as a function of probe delay and cell pressure are discussed. Single-shot measurement accuracies were within 0.1 to 6.5% when compared to a transducer values, while the precision was generally between 1% and 6% of measured pressure for probe delays of 200 ps or more, and better than 2% as the delay approached 300 ps. A byproduct of the pressure measurement is an independent but simultaneous measurement of the gas temperature.

Kearney, Sean P.↗
NASA NTRS1986

Halogen occultation experiment (HALOE) performance verification test procedure

The Performance Verification Test Procedure is given for the Halogen Occultation Experiment (HALOE) instrument, which is being developed in house at the Langley Research Center for the Upper Atmosphere Research Satellite (UARS). This procedure is used for comprehensive performance testing of the HALOE instrument which occurs before, during, and after flight environmental tests. The radiometric performance tests include noise, drift, linearity, instantaneous field-of-view, cal wheel gas cell characterization, and self thermal emissions. Pointer/tracker performance tests include sun sensor performance, gimbal performance, control system performance, and boresight alignment. In addition, the instrument is tested functionally in simulated orbit sequences and all command operating modes are exercised. The data analysis required for each test is specified and pass/fail criteria are given where applicable. This test will fully demonstrate the HALOE instrument's ability to achieve science mission requirements. The HALOE instrument is a gas correlation radiometer that measures vertical distribution of eight upper atmospheric constituents: O3, HCl, HF, NO, CH4, H2O, NO2, and CO2.

Mauldin, L. E., III↗
NASA NTRS1991

Measurement of tropospheric carbon monoxide using gas filter radiometers

The measurement of tropospheric carbon monoxide with gas filter radiometers is examined on the basis of the MAPS experiment. The performance characteristics of an instrument that uses the MAPS detectors, broadband filters, and gas cells in a system similar to the GASCOFIL system described by Morrow and Nicholls (1985) is determined. The signal function for two carbon monoxide channels of the MAPS instrument as it was flown in 1981 is shown. The measurements of the lower pressure channel are weighted to a higher altitude. The signal function, when integrated over altitude and multiplied by the normalization constant, yields the value of the signal. Both signal functions approach zero at the top because the gas concentration approaches zero. The present data reduction technique assumes that there are no clouds in the field of view. If clouds are present, the inferred carbon monoxide mixing ratio is too high, and those points must be rejected from the data set.

Reichle, Henry G., Jr.↗
NASA NTRSDate not supplied

TechEdSat 7, 10, 13, 15: Exo-brake Experiments on the ISS, First Virgin Orbit, and First Firefly-Alpha Test Flights.

The TechEdSat flight series (TES-n), developed by the Nano Orbital Workshop (NOW) group at NASA Ames, has been studying cube satellite re-entry technologies with a focus on Exo-Brake drag device research. An exo-atmospheric braking device, the Exo-Brake uses the tenuous upper atmosphere acting in a free molecular flow regime to enable controllable adjustment of the drag profile of the host spacecraft, currently enabling rapid disposal of small spacecraft after mission conclusion, and eventual targeted de-orbit to a desired entry point at the Von Karman line, or approximately 100km in altitude. The TES-7 mission, flown on the first successful Virgin Orbit flight January 17, 2021, was injected into a 500km, 61-degree inclination orbit, with an expected orbital lifetime of approximately ten years. After successful deployment of a unique hydrogen gas-cell inflation design ‘disposal’-type Mylar Exo-Brake intended to rapidly de-orbit the spacecraft, the maximum expected orbital lifetime of the TES-7 spacecraft was successfully reduced from ten years to 1.3 years, an 87% reduction in orbit lifetime via a passive, fuel-less system. The subsequent TES-13 mission utilized a new, less complex ‘disposal’-type Exo-Brake design made from collapsible rigid struts rather than inflated struts to reduce the engineering, construction, and safety complexities introduced by the prior hydrogen gas inflation design. The rigid strut Exo-Brake design is stowed via rotational compression and deploys using only stored spring energy once released via electronic actuator. This new rotation compression storage design has become the new Exo-Brake design standard used on TES missions thanks to its simplicity. Following on the success of this new Exo-Brake design demonstrated by TES-13, the design was further refined to enabled active manipulation of the Exo-Brake effective drag area though a winch-like system. Both the TES-10 and TES-15 spacecraft were equipped with geometrically similar Exo-Brake devices capable of such active drag modulation, with the intent of studying the operational impact of having such devices on cube satellite missions. To increase the survival time of the Exo-Brake at low altitudes and thus gain more experiment time and better guidance capability, TES-15 was equipped with a modulated Exo-Brake constructed from 3M™ Nextel™ 440 ceramic oxide fiber, the same fabric material used in the Space Shuttle TPS system, rather than Mylar. After launching on Alpha Flight 2 October 1st, 2022, Firefly’s first successful launch, TES-15 met the same modulation restrictions as TES-10, with modulation prohibited above 200km to avoid possible collision with other spacecraft. In this case, a low deployment orbit caused an extremely short mission life, which, coupled with delayed spacecraft identification, exacerbated collision concerns and caused performance data of the high-temperature Exo-Brake design to be inconclusive. As such, the Nano Orbital Workshop has taken a new approach of only conducting modulated Exo-Brake research on missions deploying below ISS altitude to avoid collision avoidance restrictions, and is working to improve spacecraft identification and location reporting techniques to increase experiment durations. Upcoming TES mission will therefore use one of two classes of Exo-Brake depending on their target altitude, as to be described in the submission.

M Murbach↗
NASA NTRSDate not supplied

TechEdSat 7, 10, 13, 15: Exo-brake Experiments on the ISS, First Virgin Orbit, and First Firefly-Alpha Test Flights

The TechEdSat flight series (TES-n), developed by the Nano Orbital Workshop (NOW) group at NASA Ames, has been studying cube satellite re-entry technologies with a focus on Exo-Brake drag device research. An exo-atmospheric braking device, the Exo-Brake uses the tenuous upper atmosphere acting in a free molecular flow regime to enable controllable adjustment of the drag profile of the host spacecraft, currently enabling rapid disposal of small spacecraft after mission conclusion, and eventual targeted de-orbit to a desired entry point at the Von Karman line, or approximately 100km in altitude. The TES-7 mission, flown on the first successful Virgin Orbit flight January 17, 2021, was injected into a 500km, 61-degree inclination orbit, with an expected orbital lifetime of approximately ten years. After successful deployment of a unique hydrogen gas-cell inflation design ‘disposal’-type Mylar Exo-Brake intended to rapidly de-orbit the spacecraft, the maximum expected orbital lifetime of the TES-7 spacecraft was successfully reduced from ten years to 1.3 years, an 87% reduction in orbit lifetime via a passive, fuel-less system. The subsequent TES-13 mission utilized a new, less complex ‘disposal’-type Exo-Brake design made from collapsible rigid struts rather than inflated struts to reduce the engineering, construction, and safety complexities introduced by the prior hydrogen gas inflation design. The rigid strut Exo-Brake design is stowed via rotational compression and deploys using only stored spring energy once released via electronic actuator. This new rotation compression storage design has become the new Exo-Brake design standard used on TES missions thanks to its simplicity. Following on the success of this new Exo-Brake design demonstrated by TES-13, the design was further refined to enabled active manipulation of the Exo-Brake effective drag area though a winch-like system. Both the TES-10 and TES-15 spacecraft were equipped with geometrically similar Exo-Brake devices capable of such active drag modulation, with the intent of studying the operational impact of having such devices on cube satellite missions. To increase the survival time of the Exo-Brake at low altitudes and thus gain more experiment time and better guidance capability, TES-15 was equipped with a modulated Exo-Brake constructed from 3M™ Nextel™ 440 ceramic oxide fiber, the same fabric material used in the Space Shuttle TPS system, rather than Mylar. After launching on Alpha Flight 2 October 1st, 2022, Firefly’s first successful launch, TES-15 met the same modulation restrictions as TES-10, with modulation prohibited above 200km to avoid possible collision with other spacecraft. In this case, a low deployment orbit caused an extremely short mission life, which, coupled with delayed spacecraft identification, exacerbated collision concerns and caused performance data of the high-temperature Exo-Brake design to be inconclusive. As such, the Nano Orbital Workshop has taken a new approach of only conducting modulated Exo-Brake research on missions deploying below ISS altitude to avoid collision avoidance restrictions, and is working to improve spacecraft identification and location reporting techniques to increase experiment durations. Upcoming TES mission will therefore use one of two classes of Exo-Brake depending on their target altitude, as to be described in the submission.

Marcus Murbach↗
NASA NTRS2008

Compact, Highly Stable Ion Atomic Clock

A mercury-ion clock now at the breadboard stage of development (see figure) has a stability comparable to that of a hydrogen-maser clock: In tests, the clock exhibited an Allan deviation of between 2 x 10(exp -13) and 3 x 10(exp -13) at a measurement time of 1 second, averaging to about 10(exp -15) at 1 day. However, the clock occupies a volume of only about 2 liters . about a hundredth of the volume of a hydrogen-maser clock. The ion-handling parts of the apparatus are housed in a sealed vacuum tube, wherein only a getter pump is used to maintain the vacuum. Hence, this apparatus is a prototype of a generation of small, potentially portable high-precision clocks for diverse ground- and space-based navigation and radio science applications. Furthermore, this new ion-clock technology is about 100 times more stable and precise than the rubidium atomic clocks currently in use in the NAV STAR GPS Earth-orbiting satellites. In this clock, mercury ions are shuttled between a quadrupole and a 16-pole linear radio-frequency trap. In the quadrupole trap, the ions are tightly confined and optical state selection from a Hg-202 radio-frequency-discharge ultraviolet lamp is carried out. In the 16-pole trap, the ions are more loosely confined and atomic transitions resonant at frequency of about 40.507 GHz are interrogated by use of a microwave beam at that frequency. The trapping of ions effectively eliminates the frequency pulling caused by wall collisions inherent to gas-cell clocks. The shuttling of the ions between the two traps enables separation of the state-selection process from the clock microwave- resonance process, so that each of these processes can be optimized independently of the other. The basic ion-shuttling, two-trap scheme as described thus far is not new: it has been the basis of designs of prior larger clocks. The novelty of the present development lies in major redesigns of its physics package (the ion traps and the vacuum and optical subsystems) to effect the desired reduction of size to a volume of no more than a couple of liters. The redesign effort has included selection of materials for the vacuum tube, ion trap, and ultraviolet windows that withstand bakeout at a temperature of approx.450 C in preparation for sealing the tube to contain the vacuum. This part of the redesign effort follows the approach taken in the development of such other vacuum-tube electronic components as flight traveling- wave-tube amplifiers having operational and shelf lives as long as 15 years. The redesign effort has also included a thorough study of residual-gas-induced shifts of the ion-clock frequency and a study of alternative gases as candidates for use as a buffer gas within the sealed tube. It has been found that neon is more suitable than is helium, which has been traditionally used for this purpose, in that the pressure-induced frequency pulling by neon is between a third and a half of that of helium. In addition, because neon diffuses through solids much more slowly than does helium, the loss of neon by diffusion over the operational lifetime is expected to be negligible.

Prestage, John↗
DOE OSTI2024

Unraveling the adsorption-limited hydrogen oxidation reaction at palladium surface via in situ electron microscopy

Palladium (Pd) catalysts have been extensively studied for the direct synthesis of H 2 O through the hydrogen oxidation reaction at ambient conditions. This heterogeneous catalytic reaction not only holds considerable practical significance but also serves as a classical model for investigating fundamental mechanisms, including adsorption and reactions between adsorbates. Nonetheless, the governing mechanisms and kinetics of its intermediate reaction stages under varying gas conditions remain elusive. This is attributed to the intricate interplay between adsorption, atomic diffusion, and concurrent phase transformation of catalyst. Herein, the Pd-catalyzed, water-forming hydrogen oxidation is studied in situ, to investigate intermediate reaction stages via gas cell transmission electron microscopy. The dynamic behaviors of water generation, associated with reversible palladium hydride formation, are captured in real time with a nanoscale spatial resolution. Our findings suggest that the hydrogen oxidation rate catalyzed by Pd is significantly affected by the sequence in which gases are introduced. Through direct evidence of electron diffraction and density functional theory calculation, we demonstrate that the hydrogen oxidation rate is limited by precursors’ adsorption. These nanoscale insights help identify the optimal reaction conditions for Pd-catalyzed hydrogen oxidation, which has substantial implications for water production technologies. The developed understanding also advocates a broader exploration of analogous mechanisms in other metal-catalyzed reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Verification and benchmarking relativistic electron beam transport through a background gas

It is necessary to establish confidence in high-consequence codes containing an extensive suite of physics algorithms in the regimes of interest. Verification problems allow code developers to assess numerical accuracy and increase confidence that specific sets of model physics were implemented correctly in the code. The two main verification techniques are code verification and solution verification. In this work, we present verification problems that can be used in other codes to increase confidence in simulations of relativistic beam transport. Specifically, we use the general plasma code EMPIRE to model and compare with the analytical solution to the evolution of the outer radial envelope of a relativistic charged particle beam. Additionally, we also outline a benchmark test of a relativistic beam propagating through a vacuum and pressurized gas cell, and present the results between EMPIRE and the hybrid code GAZEL. Further, we discuss the subtle errors that were caught with these problems and detail lessons learned.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Adapting an Electron Microscopy Microheater for Correlated and Time-Resolved Ambient Pressure X-ray Photoelectron Spectroscopy

Environmental transmission electron microscopy (ETEM) can follow structural and chemical changes in nanomaterials under reaction conditions, including at temperatures up to 1300 °C and pressures up to ~20 mbar. However, ETEM studies are limited to localized areas of a sample and can benefit from correlative studies of a similar sample on larger length scales. Here, in this work, we describe the customization of a commercial microheater holder used in ETEM to anode-based ambient pressure X-ray photoelectron spectroscopy (APXPS), where chemical and electronic structure information is averaged over several hundred square micrometers. To benchmark heating capabilities in the APXPS instrument, core level binding energies were followed during surface chemical reactions of a Pd film, including CO adsorption–desorption, Pd oxidation, and PdO reduction. The fast heating feature of the microheaters advanced XPS experimental capabilities, including the collection of subsecond time-resolved spectra of the Pd 3d 5/2 peak during the reduction of an oxidized Pd film. The potential to use these heaters in a closed gas cell was also demonstrated by oxidizing Pd in a partial pressure of air locally dosed to the sample surface. General tips and considerations for the application of commercial ETEM heaters to any XPS system with a focused X-ray beam are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Revealing High-Temperature Reduction Dynamics of High-Entropy Alloy Nanoparticles via In Situ Transmission Electron Microscopy

Understanding the behavior of high-entropy alloy (HEA) materials under hydrogen (H 2 ) environment is of utmost importance for their promising applications in structural materials, catalysis, and energy-related reactions. Herein, the reduction behavior of oxidized FeCoNiCuPt HEA nanoparticles (NPs) in atmospheric pressure H-2 environment was investigated by in situ gas-cell transmission electron microscopy (TEM). The reduction reaction front was maintained at the external surface of the oxide. During reduction, the oxide layer expanded and transformed into porous structures where oxidized Cu was fully reduced to Cu NPs while Fe, Co, and Ni remained in the oxidized form. In situ chemical analysis showed that the expansion of the oxide layer resulted from the outward diffusion flux of all transition metals (Fe, Co, Ni, Cu). Revealing the H-2 reduction behavior of HEA NPs facilitates the development of advanced multicomponent alloys for applications targeting H 2 formation and storage, catalytic hydrogenation, and corrosion removal.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

In Situ Oxidation Studies of High-Entropy Alloy Nanoparticles

Although high-entropy alloys (HEAs) have shown tremendous potential for elevated temperature, anticorrosion, and catalysis applications, little is known on how HEA materials behave under complex service environments. Herein, we studied the high-temperature oxidation behavior of Fe 0.28 Co 0.21 Ni 0.20 Cu 0.08 Pt 0.23 HEA nanoparticles (NPs) in an atmospheric pressure dry air environment by in situ gas-cell transmission electron microscopy. It is found that the oxidation of HEA NPs is governed by Kirkendall effects with logarithmic oxidation rates rather than parabolic as predicted by Wagner's theory. Further, the HEA NPs are found to oxidize at a significantly slower rate compared to monometallic NPs. The outward diffusion of transition metals and formation of disordered oxide layer are observed in real time and confirmed through analytical energy dispersive spectroscopy, and electron energy loss spectroscopy characterizations. Localized ordered lattices are identified in the oxide, suggesting the formation of Fe 2 O 3 , CoO, NiO, and CuO crystallites in an overall disordered matrix. Hybrid Monte Carlo and molecular dynamics simulations based on first-principles energies and forces support these findings and show that the oxidation drives surface segregation of Fe, Co, Ni, and Cu, while Pt stays in the core region. The present work offers key insights into how HEA NPs behave under high-temperature oxidizing environment and sheds light on future design of highly stable alloys under complex service conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Spatial defects nanoengineering for bipolar conductivity in MoS 2

Understanding the atomistic origin of defects in two-dimensional transition metal dichalcogenides, their impact on the electronic properties, and how to control them is critical for future electronics and optoelectronics. Here, we demonstrate the integration of thermochemical scanning probe lithography (tc-SPL) with a flow-through reactive gas cell to achieve nanoscale control of defects in monolayer MoS 2 . The tc-SPL produced defects can present either p- or n-type doping on demand, depending on the used gasses, allowing the realization of field effect transistors, and p-n junctions with precise sub-μm spatial control, and a rectification ratio of over 10 4 . Doping and defects formation are elucidated by means of X-Ray photoelectron spectroscopy, scanning transmission electron microscopy, and density functional theory. We find that p-type doping in HCl/H 2 O atmosphere is related to the rearrangement of sulfur atoms, and the formation of protruding covalent S-S bonds on the surface. Alternatively, local heating MoS 2 in N 2 produces n-character.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The design of a photoionization front experiment using the Z-Machine as a driving source and estimated measurements

Radiation-driven heat fronts are present in the early universe during reionization, the circumstellar medium of supernovae, and in high-energy-density physics experiments. Dedicated experiments to observe and diagnose the behavior of these types of heat fronts can improve our understanding of these phenomena. A simulation study of photoionization fronts using the HELIOS-CR radiation hydrodynamics code provides an experimental design for the Z-Machine at Sandia National Laboratory using a measurement-calibrated input radiation flux to drive the photoionization front. The simulations use detailed atomic physics and non-diffusive radiation transport in 1D to determine an optimal gas pressure of 0.75 atm for an experiment in N gas as well as the effects of increasing the thickness of the window that seals the gas cell. Post-processing of these simulations demonstrates that ratios of atomic rate coefficients place the heat front in a physics regime where photoionization dominates the energy deposition. Here, to see the sensitivity of the simulations to changes in the model and spatial grid, this analysis performed resolution, atomic model detail, and radiation transport angular grid studies showing less than 10% deviation from the nominal model for increased complexity, when possible. An effort to emulate 3D geometric effects on the radiation flux using an artificial attenuation scheme has shown that, even for conservative estimates of the flux, simulations still produce a photoionization front. Estimations of a streaked, visible spectroscopy measurement using SPECT3D showed that line emission measurements are present early in time and that later in time thermal emission should become dominant.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Soft x-ray high-harmonic generation in an anti-resonant hollow core fiber driven by a 3 μ m ultrafast laser

High-harmonic upconversion driven by a mid-infrared femtosecond laser can generate coherent soft x-ray beams in a tabletop-scale setup. Here, we report on a compact ytterbium-pumped optical parametric chirped pulse amplifier (OPCPA) laser system seeded by an all-fiber front-end and employing periodically poled lithium niobate (PPLN) nonlinear media operated near the pulse fluence limits of current commercially available PPLN crystals. The OPCPA delivers 3 µm wavelength pulses with 775 µJ energy at 1 kHz repetition rate, with transform-limited 120 fs pulse duration, diffraction-limited beam quality, and ultrahigh 0.33% rms energy stability over >18 h. Using this laser, we generate soft x-ray high harmonics (HHG) in argon gas by focusing into a low-loss, high-pressure gas-filled anti-resonant hollow core fiber (ARHCF), generating coherent light at photon energies up to the argon L-edge (250 eV) and carbon K-edge (284 eV), with high beam quality and ∼1% rms energy stability. This work demonstrates soft x-ray HHG in a high-efficiency guided-wave phase matched geometry, overcoming the high losses inherent to mid-IR propagation in unstructured waveguides, or the short interaction lengths of gas cells or jets. The ARHCF can operate in the long term without damage and with the repetition rate, stability, and robustness required for demanding applications in spectromicroscopy and imaging. Finally, we discuss routes for further optimizing the soft x-ray HHG flux by driving He at higher laser intensities using either the signal (1.5 μm) or idler wavelengths (3 μm).

Femtosecond lasers↗
DOE OSTI2021

Characterisation of a laser plasma betatron source for high resolution x-ray imaging

Abstract We report on the characterisation of an x-ray source, generated by a laser-driven plasma wakefield accelerator. The spectrum of the optimised source was consistent with an on-axis synchrotron spectrum with a critical energy of 13.8 − 1.9 + 2.2 keV and the number of photons per pulse generated above 1 keV was calculated to be 6 − 0.9 + 1.2 × 10 9 . The x-ray beam was used to image a resolution grid placed 37 cm from the source, which gave a measured spatial resolution of 4 µ m × 5 µ m. The inferred emission region had a radius and length of 0.5 ± 0.2 µ m and 3.2 ± 0.9 mm respectively. It was also observed that laser damage to the exit aperture of the gas cell led to a reduction in the accelerated electron beam charge and a corresponding reduction in x-ray flux due to the change in the plasma density profile.

plasma acceleration↗