Search NASA⌕ Search

SEARCH · Search NASA

Results for “Gasoline engines”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Laminar flame speed measurements of a gasoline surrogate and its mixtures with ethanol at elevated pressure and temperature

Laminar Flame speed measurements of a gasoline surrogate and mixtures of it with ethanol were conducted using a heated, constant-volume vessel. A spherical propagating flame was observed using a high-speed camera, and laminar flame speed was determined therefrom. Here, the gasoline surrogate, which serves as the baseline for the current study, consisted of four components, namely, iso-octane, n-heptane, toluene, and 1-hexene. Different mixtures of the gasoline surrogate and ethanol were studied, governed by the ethanol percentage in the mixture. That is, E0, E30, E50, and E85 mixtures represent 0%, 30%, 50%, and 85% ethanol in the gasoline surrogate mixture by liquid volume, respectively. Initial temperatures of 335, 359, and 408 K and initial pressures of 1 and 3 bar were investigated. The findings of this study are compared to results in the literature, which show good agreement for E0 but some deviation for the E30 blend. In general, the study showed an increase in laminar flame speed as the ethanol percentage increases in the mixture. Similarly, increasing the initial temperature with fixed ethanol percentage resulted in an increase in laminar flame speed, as expected. In contrast, increasing the initial pressure with fixed Ethanol percentage showed a decrease in laminar flame speed. Finally, the results are compared to an existing chemical kinetics model designed for ethanol and gasoline. Although agreement between the model and data is reasonable and mostly within about 10%, some improvement to the kinetics model is needed to uniformly lower the calculated flame speeds.

09 BIOMASS FUELS↗
DOE OSTI2020

Laminar-to-turbulent flame transition and cycle-to-cycle variations in large eddy simulation of spark-ignition engines

This paper investigates the effect of laminar-to-turbulent flame transition modeling on the prediction of cycle-to-cycle variations (CCVs) in large eddy simulation (LES) of spark-ignition (SI) engines. A laminar-to-turbulent flame transition model that describes the non-equilibrium sub-filter flame speed evolution during an early stage of flame kernel growth is developed. In the present model, the flame transition is characterized by the flame kernel size at which the flame transition ends, defined here as the flame transition scale. The proposed model captures the effects that variations in a turbulent flow field have on the evolution of early-stage burning rates, through variations in the flame transition scale. The proposed flame transition model is combined with the front propagation formulation (FPF) method and a spark-ignition model to predict CCVs in a gasoline direct injection SI engine. It is found that multi-cycle LES with the proposed flame transition model reproduces experimentally-observed CCVs satisfactorily. When the transition model is not considered or when variations in the transition process are neglected, CCVs are significantly under-predicted for the case considered here. These results indicate the importance of modeling the laminar-to-turbulent flame transition and the effect of turbulence on the transition process, when predicting CCVs, under certain engine conditions. The LES results are also used to analyze sources for variations in the flame transition. It is found, for the present engine case, that the most important source is the cycle-to-cycle variation in the turbulence dissipation rate, which is used to measure the strength of turbulence in the proposed model, near a spark plug. The large-scale velocity field and the variations of the laminar flame speed due to the mixture composition and thermal stratification are also found to be important factors to contribute to the variations in the flame transition.

42 ENGINEERING↗
DOE OSTI2020

Potential Impacts of High-Octane Fuel Introduction in a Naturally Aspirated, Port Fuel-Injected Legacy Vehicle

In recent years there has been an increased interest in raising the octane level of gasoline to enable higher compression ratios (CR) in spark-ignition engines to improve vehicle fuel efficiency. A number of studies have examined opportunities to increase efficiency in future vehicles, but potential impacts on the legacy fleet have not received as much attention. In this study, our effort focused on experimental studies on an engine using high-octane fuels without changing the engine’s CR. Spark timing was advanced until maximum torque was reached or knock was encountered for each engine condition, using each individual fuel to maximize engine efficiency. Knock-limited conditions occurred as the output brake mean effective pressure (BMEP) neared the maximum attainable output at a given engine speed. Increasing research octane numbers generally enabled knock-free operation under a greater number of operating conditions. Vehicle modeling using Autonomie was used to project vehicle energy use, fuel economy, and tailpipe CO 2 emissions for the Urban Dynamometer Driving Schedule (UDDS), the Highway Fuel Economy Test (HWFET), and the US06 cycle. Results show that decreases in energy consumption of up to 2% for a small SUV are possible through the use of a 97 RON fuel compared to a baseline using 91 RON fuel, provided that the formulation of the fuel does not cause unanticipated operational issues such as lower maximum BMEP. Greater improvements using high-octane fuels are possible if the CR is increased, but there is no opportunity to increase the CR in legacy vehicles. Thus, these vehicles realize an improvement from increased octane rating in accordance with their ability to spark advance to take advantage of a fuel with a higher octane rating. For the modeled vehicle, improvements of up to 2% in volumetric fuel economy may be possible through the use of a 97 RON fuel with the largest gains expected on the US06 cycle. Fuel economy impacts are strongly coupled to the heating value of the fuels in addition to changes in engine efficiency. Similarly, decreases in tailpipe CO 2 emissions are also achievable. However, simultaneous improvements in energy consumption, fuel economy, and tailpipe CO 2 emissions are not guaranteed and are dependent upon fuel formulation.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Simulation of a rapid compression machine for evaluation of ignition chemistry and soot formation using gasoline/ethanol blends

Due to the projected decline of demand for gasoline in light duty engines and the advent of ethanol as a green fuel, the use of gasoline/ethanol blend fuels in heavy duty applications are being investigated as they are projected to have lower cost and lower lifecycle green house gas (GHG) emissions. In heavy duty engines, the primary mode of combustion is mixing controlled combustion where wide range of mixture conditions (equivalence ratio) exist. Soot emissions of these fuels in richer conditions are not well understood. The goal of this research is to evaluate some commercially available soot modeling codes for the particulate matter emissions from gasoline/ethanol fuel blends, especially at fuel rich conditions. A Rapid Compression Machine (RCM) is modeled in a three-dimensional numerical simulation using CONVERGE computational software using a reduced chemical kinetic mechanism with SAGE chemistry solver and a RANS k-ϵturbulence model with a sector model including the creviced piston. The creviced piston is used in the experimental setup to reduce boundary layer effects and to maintain a homogeneous core in the reaction cylinder. Computational fluid dynamics simulations are conducted for different gasoline-ethanol fuel blends from E10 (10% ethanol v/v) to E100. The fuel blend is modeled as a surrogate mixture of toluene, iso-octane, n-heptane for gasoline content, and ethanol. The computational results were validated against experimental results using pressure measurements and laser extinction diagnostics. Different soot models are investigated to evaluate their capability of predicting the sooting tendencies of fuel blends, especially in richer conditions experienced during mixing-controlled combustion. The experimental combustion characteristics such as the ignition delay of different blends of fuel are reasonably well predicted. The Particulate Size Mimic (PSM) model accurately predicts the soot generation characteristics of the different fuels, but the Hiroyasu-NSC model falls short in this regard. For accurate prediction of soot with the PSM model, the thermodynamic conditions during combustion must be accurately modeled. While the current computational modeling tools can produce accurate results for the prediction of particulate matter emissions, there is much work to be done in improving our understanding of the underlying fundamental processes.

Energy & Fuels↗
DOE OSTI2020

A control-oriented combustion model framework for compression ignition engines operating on low-reactivity fuel

This work focuses on zero-dimensional modeling of the heat release rate in a compression ignition engine operating on gasoline-like fuels. Due to the properties of gasoline, such as high volatility and longer ignition delay than diesel, the injection strategies can vary significantly from the operation with conventional diesel fuel. Different injection strategies are commonly used to achieve varying degrees of in-cylinder stratification in order to shape the combustion event and maximize efficiency. The proposed zero-dimensional combustion model was developed to account for the different stages in combustion caused by the fuel stratification. As the ignition delay model is an integral part of the entire combustion process and significantly affects the prediction accuracy, special attention has been paid to local phenomena influencing ignition delay. A one-dimensional spray model by Musculus and Kattke was employed in conjunction with a Lagrangian tracking approach in order to estimate the local air–fuel ratio within the spray tip, as a proxy for reactivity. The local air–fuel ratio, in-cylinder temperature and pressure were used in an integral fashion to estimate the ignition delay. Heat release rates were modeled using first-order non-linear differential equations. The proposed combustion model was validated against experimental data of a heavy-duty compression ignition engine with up to three injection events at mostly 1038 r/min and 14 bar brake mean effective pressure. Further validation of the model was carried out at other engine loads and speeds. Model prediction errors in CA50 of less than 1 °CA across all conditions were found. Modeling results of other combustion metrics such as combustion duration and indicated mean effective pressure are also highly satisfactory. In addition, the model has been shown to be capable of estimating the ringing intensity for most conditions.

Pamminger, Michael↗
DOE OSTI2022

Soot and PAH formation in high pressure spray pyrolysis of gasoline and diesel fuels

Time-resolved soot and PAH formation from gasoline and diesel spray pyrolysis are visualized and quantified using diffuse back illumination (DBI) and laser induced fluorescence (LIF) at 355 nm, respectively, in a constant-volume vessel at 60 bar from 1400 to 1700 K for up to 30 ms. The delay, maximum formation rate, and yield of soot and PAHs are compared across fuels and temperatures and correlated with the yield sooting indices on either the mass or mole basis. The delays generally decrease with increasing temperature, and the formation rates of both PAHs and soot generally increase with temperature. The apparent PAH-LIF yield may decrease with temperature due to PAH growth and conversion into larger species, signal trapping, and thermal quneching. Soot yield generally increases with temperature. The mass-based YSI correlates reasonably well with soot delay, but YSI does not correlate well with soot yield. Here, the mass-based YSI is a more appropriate predictor of sooting propensity than the mole-based YSI.

42 ENGINEERING↗
DOE OSTI2023

Fuel-air mixing in motored CFR engine at research octane number (RON) relevant condition

This paper presents a three-dimensional (3-D) computational fluid dynamics (CFD) study of a motored cooperative fuel research (CFR) engine at research octane number (RON) relevant condition. The boundary conditions for 3-D simulations were generated with a one-dimensional GT-Power model. For the first time in literature, a carburetor was added to a virtual CFR engine model with 3-D CFD. Therefore, the proposed setup can simulate the fuel and thermal stratifications inside the engine cylinder with realistic detail. The transient simulations in this work were performed within the Reynolds-averaged Navier-Stokes (RANS) framework with a Realizable k-ε turbulence model. Major conclusions from the present work are: (1) The in-cylinder flow of the CFR engine is swirl-dominated due to the existence of the intake valve shroud. (2) There is a significant amount of liquid droplets entering the cylinder during the intake stroke. The maximum instantaneous amount of liquid for 50% PRF 87 (containing 87% iso-octane and 13% n-heptane (v/v)) and 50% ethanol mixture is indicated to be around 26% of total injected fuel mass. (3) The heat of vaporization (HoV) of the fuel is responsible for creating both temperature and charge stratification inside the cylinder.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Influence of Fuel Properties on Gasoline Direct Injection Particulate Matter Emissions Over First 200 s of World-Harmonized Light-Duty Test Procedure Using an Engine Dynamometer and Novel “Virtual Drivetrain” Software

Abstract The influence of fuel properties on particulate matter (PM) emissions from a catalytic gasoline particulate filter (GPF) equipped gasoline direct injection (GDI) engine was investigated using novel “virtual drivetrain” software and an engine mated to an engine dynamometer. The virtual drivetrain software was developed in labview to operate the engine on an engine dynamometer as if it were in a vehicle undergoing a driving cycle. The software uses a physics-based approach to determine vehicle acceleration and speed based on engine load and a programed “shift” schedule to control engine speed. The software uses a control algorithm to modulate engine load and braking to match a calculated vehicle speed with the prescribed speed trace of the driving cycle of choice. The first 200 s of the World-harmonized Light-duty Test Procedure (WLTP) driving cycle was tested using six different fuel formulations of varying volatility, aromaticity, and ethanol concentration. The first 200 s of the WLTP was chosen as the test condition because it is the most problematic section of the driving cycle for controlling PM emissions due to the cold start and cold drive off. It was found that there was a strong correlation between aromaticity of the fuel and the engine-out PM emissions, with the highest emitting fuel producing more than double the mass emissions of the low PM production fuel. However, the post-GPF PM emissions depended greatly on the soot loading state of the GPF. The fuel with the highest engine-out PM emissions produced comparable post-GPF emissions to the lowest PM producing fuel over the driving cycle when the GPF was loaded over three cycles with the respective fuels. These results demonstrate the importance of GPF loading state when aftertreatment systems are used for PM reduction. It also shows that GPF control may be more important than fuel properties, and that regulatory compliance for PM can be achieved with proper GPF control calibration irrespective of fuel type.

Energy & Fuels↗
DOE OSTI2020

Material-Dependent Antagonistic Effects between Soot and ZDDP

While soot in engine oil is known to accelerate the wear of diesel and gasoline direct-injection compression-ignition engines, there is a lack of consensus on the wear mechanism though various hypotheses have been proposed in the literature. Particularly, some recently observed antagonistic effects between soot and a common lubricant antiwear additive, zinc dialkyldithiophosphate (ZDDP), while others did not. The discrepancy is, in part, explained by the strong alloy dependence of such antagonism discovered in this study. Specifically, four alloys, 52100 steel and M2, M50, and A2 tool steels, are tested in lubricants containing carbon black (CB, a soot surrogate) with and without ZDDP present. Adding the CB alone to the oil increases the wear rate for all steel alloys as expected. However, distinct wear performance is observed for the four steel alloys when ZDDP is introduced to the CB-containing oil: while the 52100 steel has notable wear reduction, the three tool steels suffer significant wear increase. Comprehensive tribofilm characterization suggests that the Mo content in the steel alloy and the sulfur from ZDDP strongly influence wear behavior. The combination of CB/Mo-catalyzed sulfidation and CB-accelerated abrasion is hypothesized to be responsible for the high wear of the Mo-alloyed tool steels.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Enhancing the efficiency benefit of thermal barrier coatings for homogeneous charge compression ignition engines through application of a low-k oxide

Prior experiments reported by the authors have proven the hypothesis that achieving a dynamic temperature swing on the combustion chamber surface will lead to improved thermal and combustion efficiencies of the homogeneous charge compression ignition engine. A thin layer of yttria-stabilized zirconia, roughly 150 μm, was plasma sprayed on the piston top. It led to markedly advanced ignition and heat release in the gasoline homogeneous charge compression ignition engine, accompanied with reduced unburnt hydrocarbon and carbon monoxide emissions, improved combustion efficiency, and a higher thermal efficiency. A related computational study highlighted the critical role of coating thermal conductivity in achieving a desired dynamic response; hence, the second phase of experimental investigations focused on introducing structured porosity in the yttria-stabilized zirconia coating, as a means of reducing effective conductivity. Indeed, additional incremental improvements were observed, as well as limitations related to adverse effects of the surface roughness and the fuel interactions with the surface roughness and open pores. Erosion can also be a problem in a direct injection engine. Therefore, the third round of investigations focused on a material with a natively low conductivity (low-k), sprayed on the top of an Al piston in a relatively dense form, and in a way that yields a smooth surface. The objective was to capitalize on the low conductivity, while avoiding the pitfalls accompanying high-porosity formulations. The heat-storage capacity was limited by keeping the thickness relatively low. The results verify the paramount importance of thermal conductivity in the context of high “temperature swing” behavior and indicate a potential to improve the homogeneous charge compression ignition engine’s combustion efficiency roughly 1.5%, with the overall indicated efficiency improvement on the order of 5%, on a relative basis. In addition, the low-k oxide thermal barrier applied to the piston extended significantly the low-load homogeneous charge compression ignition operability limit.

42 ENGINEERING↗
DOE OSTI2023

Thermodynamic analysis of heat transfer reduction in spark ignition using thermal barrier coatings

This work uses a 0D thermodynamic engine model coupled to a 1D surface temperature solver to study the potential of low thermal inertia thermal barrier coatings (TBCs) on combustion chamber surfaces to increase the efficiency of spark ignition engines. Under ideal conditions, coating the piston crown, head, and valve faces with a TBC with a thermal inertia of 640 J/m 2 K s 1/2 resulted in less than a 1% relative improvement in efficiency. Despite using a low thermal inertia coating to avoid open cycle charge heating, the reduction in closed cycle heat transfer, which is the pathway to increasing efficiency, increased knock propensity. Therefore, any efficiency gain through closed cycle heat transfer reduction in spark ignition is offset by the need to retard spark timing to counter knock. An exergy analysis of completely blocking heat transfer for a 10 crank-angle degree window showed that on a low compression engine, like those used for stoichiometric gasoline spark ignition, the maximum efficiency gain achievable was limited compared to a higher compression ratio engine. Furthermore, the high gas temperatures of stoichiometric operation mean that even state-of-the-art TBCs cannot elevate surface temperatures enough purely through temperature swing to achieve a significant reduction in heat transfer near top dead center, where work availability is highest. Overall, these results indicate that low thermal inertia TBCs are ill-suited for achieving an efficiency benefit in spark ignition through a heat transfer reduction pathway. Instead spark ignition TBC research should explore ways to use low thermal inertia TBCs to achieve open cycle charge cooling to reduce knock propensity.

Engineering↗
DOE OSTI2025

Impact of gasoline composition on the effects of nitric oxide on autoignition and knock in a DISI engine

Modern spark-ignition engines use exhaust gas recirculation (EGR) to dilute the charge and suppress knock, enabling the use of higher compression ratios and/or more optimum combustion phasing for higher efficiency. The effectiveness of EGR is affected by the composition of the fuel and its chemical-kinetic interactions with combustion products. Among those, nitric oxide (NO) has been shown to strongly affect autoignition reactivity. However, the impact of fuel composition of the effect of NO on reactivity is not well-understood. Here, in this study, engine experiments were conducted to assess the impact of NO seeded to the intake on knock-limited operation of two gasoline fuels (high cycloalkane content, or HCA, and high olefin content, or HO). Results showed that compositionally-different fuels responded differently to NO. HCA, which was less knock-limited than HO for NO < 200 ppm, became more knock-limited for NO > 200 ppm. Moreover, it was found that differences in knock between fuels were caused by differences in autoignition chemistry and not in the sequential autoignition process of the end gas that occurs due to thermal stratification. Chemical kinetic simulations were performed to better understand the experimental results. For HCA, intermediate-temperature heat release had a greater impact on autoignition reactivity than low-temperature heat release, while the opposite was observed for HO. For both fuels, NO enhances the magnitude of low-temperature heat release via NO + HO 2 → NO 2 + OH. The effect of NO on reactivity was stronger for HCA because OH produced from NO helped to overcome the OH quenching effect of cyclopentane, a main species in HCA. In contrast, HO had relatively strong inherent low-temperature chemistry arising from iso-octane, which reduced the impact of NO on reactivity. For the range of NO mole fractions tested in this study, in-cylinder NO increased fuel’s knock propensity, especially for fuels with mild low-temperature chemistry.

Autoignition↗
DOE OSTI2023

Soot Formation and Ignition Characteristics of Ethanol/Gasoline Blends in a Rapid Compression Machine

With the ever-increasing demand for sustainable energy, alcohol fuels have garnered interest for use in heavy duty engines. The significant infrastructure for ethanol production and blending of ethanol with gasoline make these fuels/fuel blends desirable candidates. However, development of heavy duty engine technology that is capable of burning alcohol fuels while retaining the advantages of traditional diesel combustion requires an improved understanding of the soot formation for these fuels under conditions relevant to mixing-controlled combustion. This work uses an extinction diagnostic to study the sooting tendency of ethanol and gasoline/ethanol blends ranging from E10 to E98 during ignition in a homogeneous environment. Experiments were conducted in a rapid compression machine (RCM) for compressed conditions of 20 ± 1 bar and an approximately constant temperature (± 10K) which was unique for each fuel. For a given soot volume fraction, a linear relationship was observed between ethanol content and the equivalence ratio in which that soot volume fraction was formed. Accounting for the oxygenated nature of ethanol, E85 and E98 fuels produced similar amounts of soot at a given Φ ox, , suggesting other factors outside of fuel oxygen content, such as fuel morphology, impact soot formation. Ignition delay data is reported for compressed pressures of 20 ± 1 bar and compressed temperatures ranging from 633 – 670 K for E10 and 771 – 789 K for E98. Varying pressures for E10 and E98 at conditions producing similar soot volume fractions demonstrated a linear dependence of soot formation on pressure, regardless of if the pressure considered was at top dead center or peak combustion pressure. Furthermore, the data gleaned from this work will be used to select soot models and chemical kinetic mechanisms for RCM simulations to ultimately model heavy duty engine technology with the studied fuels.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Influence of gasoline fuel formulation on lean autoignition in a mixed-mode-combustion (deflagration/autoignition) engine

We report stoichiometric spark-ignition engines suffer efficiency penalties due to throttling losses at low loads, a low specific-heat ratio of the stoichiometric working fluid, and limits on compression ratio due to end-gas autoignition leading to undesirable knocking. Mixed-Mode Combustion (MMC) mitigates these shortcomings by using a lean working fluid where a spark-initiated pilot-stabilized deflagrative flame front is followed by controlled end-gas autoignition. This MMC study investigates the effects of initial conditions (intake air temperature, intake pressure, equivalence ratio, and intake oxygen fraction) on autoignition tendency of four gasoline-range fuels with varying properties and composition. The use of fuels with varying octane sensitivity (S) allowed exploring the importance of low-temperature heat release in triggering autoignition. Fuels with high S were less reactive for conditions that promote low-temperature chemistry (operation at high intake air pressure or without N2 dilution). Conversely, an Alkylate fuel with low S showed a greater autoignition resistance at operating conditions that were unfavorable for low-temperature chemistry. Next, the effect of residual gas composition on autoignition tendency of fuels was examined with a chemical-kinetics model. Among the various molecules in the residual gas, nitric oxide (NO) enhanced the low-temperature chemistry and increased the autoignition tendency most significantly. The fuels’ autoignition response to increasing NO amount corroborates the experimental observations. Next, the sequential autoignition of the end-gas was assessed to be less impacted by thermal stratification because of lean mixtures showing relatively less low-temperature chemistry, when compared to stoichiometric mixtures. Next, the effect of changing equivalence ratio on the autoignition was found to be similar for all fuels, regardless of their S. With changing intake air temperature, the response of fuels’ autoignition tendency depended on the dilution level used. At high dilution (i.e. low intake [O2]), fuels’ reactivity increased with increasing intake air temperature. In contrast, for operation without dilution, the autoignition tendency of the low-S Alkylate fuel decreased with increasing intake air temperature, while that of high-S High Cycloalkane fuel still increased with increasing intake air temperature. In conclusion, conventional octane metrics (RON and MON) have utility in assessing the autoignition tendency under lean MMC operation. Moreover, the fuel requirements for MMC align with that of stoichiometric operation: i.e., high RON and high S fuels are desirable for stable non-knocking operation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Effects of Critical Compression Ratio on Rating Gasoline Knock Propensity

It is common practice in the automotive industry to explore the knock limits of fuels on an engine by a comparison of the knock limited spark advance (KLSA) at threshold knock intensity. However, the knock propensity of gasolines can be rated by changing one of three metrics on a variable compression ratio Cooperative Fuels Research (CFR) octane rating engine while holding the other two variables constant: knock intensity, spark timing, and critical compression ratio. The operational differences between the standard research octane number (RON) rating and modern engine operation have been explored in three parts. The first part focused on the effects of lambda and knock characterization. The second part studied the effects of spark timing. This third part explores the knock ratings of several gasolines by comparing the critical compression ratios at constant combustion phasing and knock intensity. The threshold knock intensity was based on the standard octane rating D1 pickup or by maximum amplitude of pressure oscillations (MAPO) measured by a piezoelectric cylinder pressure transducer. Several Fuels for Advanced Combustion Engines (FACE) gasolines, primary reference fuels (PRFs), and toluene standardization fuels (TSFs) were tested on a CFR octane rating engine with advanced data acquisition equipment and a piezoelectric cylinder pressure transducer. These tests deviated from the ASTM D2699 standard octane rating procedure. For each test fuel, the CFR engine was operated at stoichiometry at a constant combustion phasing (CA50) and the compression ratio was modified until a threshold knock intensity was realized. It was found that the chemical composition of the fuels affected the relationship of critical compression ratios between the D1 knockmeter and piezoelectric pressure transducer knock intensity thresholds, as well as the measured combustion maximum pressure rise rate and spark timing setting for constant CA50. For highly aromatic fuels tested at a constant MAPO knock intensity threshold, it was found that the maximum pressure rise rate was two to three times higher than that of highly paraffinic fuels with similar RON and the spark advance was several crank angle degrees less for constant combustion phasing.

Kolodziej, Christopher P↗
DOE OSTI2020

Numerical study on spray collapse process of ECN spray G injector under flash boiling conditions

This work features a numerical study of the spray collapse process that occurs under flash-boiling, gasoline-direct-injection conditions. The Engine Combustion Network's Spray G injector was modeled, and iso-octane, n-hexane, and propane were used as fuels with the goal to investigate fuel property effects. The development of individual jets and jet-to-jet interaction were analyzed to reveal the physical mechanisms of spray collapse. The results agreed qualitatively well with the experimental data of propane available from the literature and the predictions revealed the model's ability to capture the near-nozzle shock structures witnessed in the experiments. Simulations showed that the flow development of flashing sprays was strongly tied with the fuel properties. Specifically, under-expanded jets were not observed with iso-octane due to the fuel's low vapor pressure. In the case of n-hexane, the jets were under-expanded, and a low-pressure core was observed inside the jets due to the flow expansion. With propane, the very strong expansion caused the flow to become transonic and generate a unique shock structure near the nozzle exit. The shock structure revealed the formation of primary shock cells within the jets and secondary shock cells induced by jet-to-jet interaction. Based on the results, the spray collapse under flash boiling conditions was mainly attributed to two effects, i.e., the decrease in pressure at the spray center induced by the low-pressure cores inside and between the jets, and the isolation effect due to the jet-to-jet interaction which contributed to maintain the pressure differential between the spray center and the ambient.

42 ENGINEERING↗
DOE OSTI2022

An experimental and modeling study on autoignition of 2-phenylethanol and its blends with n-heptane

2-Phenylethanol (2-PE) is an aromatic alcohol with high research octane number, high octane sensitivity, and a potential to be produced using biomass. Considering that 2-PE can be used as a fuel additive for boosting the anti-knocking quality of gasoline in spark-ignition engines and as the low reactivity fuel or fuel component in dual-fuel reactivity controlled compression ignition (RCCI) engines, it is of fundamental and practical interest to understand the autoignition chemistry of 2-PE, especially at low-to-intermediate temperatures (<1000 K). Based upon the experimental ignition delay time (IDT) results of neat 2-PE obtained from our previous rapid compression machine (RCM) investigation and the literature shock tube study, a detailed chemical kinetic model of 2-PE is developed herein, covering low-to-high temperature regimes. Besides, RCM experiments using binary fuel blends of 2-PE and n-heptane (nC7) are conducted in this work to investigate the nC7/2-PE blending effects, as they represent a dual-fuel system for RCCI operations. Furthermore, the newly developed 2-PE model is merged with a well-validated nC7 kinetic model to generate the current nC7/2-PE binary blend model. Overall, the consolidated model reasonably predicts the experimental IDT data of neat 2-PE and nC7/2-PE blends, as well as captures the experimental effects of pressure, equivalence ratio, and blending ratio on autoignition. Finally, model-based chemical kinetic analyses are carried out to understand and identify the controlling chemistry accounting for the observed blending effects in RCM experiments. In conclusion, the analyses reveal that nC7 enhances 2-PE autoignition via providing extra $\dot{O}$H radicals to the shared radical pool, while the diminished nC7 promoting effect on 2-PE autoignition with increasing temperature is due to the negative temperature coefficient characteristics of nC7.

2-phenlyethanol↗