Search NASA⌕ Search

SEARCH · Search NASA

Results for “Geometric parametrization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Three-dimensional analysis of a postbuckled embedded delamination

Delamination growth caused by local buckling of a delaminated group of plies was investigated. Delamination growth was assumed to be governed by the strain energy release rates, G(1), G(2) and G(3). The strain energy release rates were calculated using a geometrically nonlinear three-dimensional finite element analysis. The program is described and several checks of the analysis are discussed. Based on a limited parametric study, the following conclusions were reached: (1) the problem is definitely mixed mode (in some cases G(1) is larger than G(2), for other cases the opposite is true); (2) in general, there is a large gradient in the strain energy release rates along the delamination front; (3) the locations of maximum G(1) and G(2) depend on the delamination shape and the applied strain; (4) the mode 3 component was negligible for all cases considered; and (5) the analysis predicted that parts of the delamination would overlap. The results presented did not impose contact constraints to prevent overlapping. Further work is needed to determine the effects of allowing the overlapping.

Whitcomb, John D.↗
NASA NTRS2010

Vehicle Sketch Pad: a Parametric Geometry Modeler for Conceptual Aircraft Design

The conceptual aircraft designer is faced with a dilemma, how to strike the best balance between productivity and fidelity? Historically, handbook methods have required only the coarsest of geometric parameterizations in order to perform analysis. Increasingly, there has been a drive to upgrade analysis methods, but these require considerably more precise and detailed geometry. Attempts have been made to use computer-aided design packages to fill this void, but their cost and steep learning curve have made them unwieldy at best. Vehicle Sketch Pad (VSP) has been developed over several years to better fill this void. While no substitute for the full feature set of computer-aided design packages, VSP allows even novices to quickly become proficient in defining three-dimensional, watertight aircraft geometries that are adequate for producing multi-disciplinary meta-models for higher order analysis methods, wind tunnel and display models, as well as a starting point for animation models. This paper will give an overview of the development and future course of VSP.

Hahn, Andrew S.↗
NASA NTRS1984

Analysis and testing of a new method for drop size measurement using laser scatter interferometry

Research was conducted on a laser light scatter detection method for measuring the size and velocity of spherical particles. The method is based upon the measurement of the interference fringe pattern produced by spheres passing through the intersection of two laser beams. A theoretical analysis of the method was carried out using the geometrical optics theory. Experimental verification of the theory was obtained by using monodisperse droplet streams. Several optical configurations were tested to identify all of the parametric effects upon the size measurements. Both off-axis forward and backscatter light detection were utilized. Simulated spray environments and fuel spray nozzles were used in the evaluation of the method. The measurements of the monodisperse drops showed complete agreement with the theoretical predictions. The method was demonstrated to be independent of the beam intensity and extinction resulting from the surrounding drops. Signal processing concepts were considered and a method was selected for development.

Bachalo, W. D.↗
NASA NTRS1990

A computational parametric study of three-dimensional sidewall compression scramjet inlets at Mach 10

A computational parametric study of three-dimensional sidewall compression scramjet inlets has been performed. The parameters considered for the study include the leading edge sweep angle, varied between 30 and 60 degrees, and the cowl position, located at the throat and at two forward positions. Additionally, the effects of laminar and turbulent boundary layers as well as adiabatic and cold wall boundary conditions are assessed. The parametric study is performed for a Mach number of 10 and a unit freestream Reynolds number of 2 x 10 to the 6th/ft at a geometric contraction ratio of 5. Comparisons among the various configurations are made in terms of the gross parameters of mass capture, throat Mach number, total pressure recovery, and area weighted internal pressure ratios, as well as more detailed flow field phenomena comparisons. The inclusion of one 0-deg sweep computation indicates that the leading edge may be swept by up to 30 deg before significant changes in the gross flow field parameters occur. It is found that a 45-deg sweep configuration provides a good compromise of mass capture, total pressure recovery, and internal compression.

Holland, Scott D.↗
NASA NTRS1992

Perceptual bias for forward-facing motion

When an occluded horizontal row of shapes is shifted laterally, apparent motion can be experienced in either the leftward or the rightward direction. Four experiments provide evidence for a motion bias in the direction that shapes appear to face. The bias tended to be largest when directionality was specified geometrically (e.g., triangles), next largest when it was specified biologically (e.g., mice), and absent when it was specified calligraphically (e.g., letter R). The bias increased parametrically as a function of triangle pointedness and was consistent with the directional interpretation of an ambiguous duck-rabbit. The results support the existence of a cognitively specified forward-facing attribute that can influence experienced direction of motion.

Mcbeath, Michael K.↗
NASA NTRS2013

Multiphysics Modeling of a Single Channel in a Nuclear Thermal Propulsion Grooved Ring Fuel Element

In the past, fuel rods have been used in nuclear propulsion applications. A new fuel element concept that reduces weight and increases efficiency uses a stack of grooved discs. Each fuel element is a flat disc with a hole on the interior and grooves across the top. Many grooved ring fuel elements for use in nuclear thermal propulsion systems have been modeled, and a single flow channel for each design has been analyzed. For increased efficiency, a fuel element with a higher surface-area-to-volume ratio is ideal. When grooves are shallower, i.e., they have a lower surface area, the results show that the exit temperature is higher. By coupling the physics of turbulence with those of heat transfer, the effects on the cooler gas flowing through the grooves of the thermally excited solid can be predicted. Parametric studies were done to show how a pressure drop across the axial length of the channels will affect the exit temperatures of the gas. Geometric optimization was done to show the behaviors that result from the manipulation of various parameters. Temperature profiles of the solid and gas showed that more structural optimization is needed to produce the desired results. Keywords: Nuclear Thermal Propulsion, Fuel Element, Heat Transfer, Computational Fluid Dynamics, Coupled Physics Computations, Finite Element Analysis

Kim, Tony↗
NASA NTRS1975

Effects of geometric variables on the performance of a probe for direct measurement of free-steam stagnation pressure in supersonic flow

An investigation was conducted at Mach numbers of 1.41, 1.83, and 2.20 to determine the effects of parametric variations in the height of the pitot-tube center line from the probe surface and in the radius of the surface curvature on the pressure recovery of a probe designed to measure the free-stream stagnation pressure. The probe consists of a pitot tube mounted on the surface of a curved cylinder of circular cross section. The pitot tube senses the pressure of the stream tube which has been slowed by isentropic compression along the curved surface. Pressure recovery, greater than or equal to 99.8 percent of the free-stream stagnation pressure, was obtained for a wide range both of angle of attack and of yaw for probes satisfying the predetermined optimum design criteria.

Couch, L. M.↗
NASA NTRS1995

A Parametric Investigation of Nozzle Planform and Internal/External Geometry at Transonic Speeds

An experimental investigation of multidisciplinary (scarfed trailing edge) nozzle divergent flap geometry was conducted at transonic speeds in the NASA Langley 16-Foot Transonic Tunnel. The geometric parameters investigated include nozzle planform, nozzle contouring location (internal and/or external), and nozzle area ratio (area ratio 1.2 and 2.0). Data were acquired over a range of Mach Numbers from 0.6 to 1.2, angle-of-attack from 0.0 degrees to 9.6 degrees and nozzle pressure ratios from 1.0 to 20.0. Results showed that increasing the rate of change internal divergence angle across the width of the nozzle or increasing internal contouring will decrease static, aeropropulsive and thrust removed drag performance regardless of the speed regime. Also, increasing the rate of change in boattail angle across the width of the nozzle or increasing external contouring will provide the lowest thrust removed drag. Scarfing of the nozzle trailing edges reduces the aeropropulsive performance for the most part and adversely affects the nozzle plume shape at higher nozzle pressure ratios thus increasing the thrust removed drag. The effects of contouring were primary in nature and the effects of planform were secondary in nature. Larger losses occur supersonically than subsonically when scarfing of nozzle trailing edges occurs. The single sawtooth nozzle almost always provided lower thrust removed drag than the double sawtooth nozzles regardless the speed regime. If internal contouring is required, the double sawtooth nozzle planform provides better static and aeropropulsive performance than the single sawtooth nozzle and if no internal contouring is required the single sawtooth provides the highest static and aeropropulsive performance.

Cler, Daniel L.↗
DOE OSTI2025

Advancing the STS Neutron Moderator Design with an Automated Optimization Workflow and Unstructured Mesh Modeling

With the Second Target Station approaching its final design phase, a detailed neutronics evaluation of its critical components is necessary. Optimizing the dimensions of the two cold-source moderators that are at the heart of this facility presents a multi-objective optimization problem for which an accurate geometric description is crucial. We have applied a fully automated optimization workflow in which a detailed unstructured mesh geometry is automatically generated with Attila4MC, starting from a parametrized CREO geometry followed by preprocessing with SpaceClaim. With this geometry, a MCNP run is performed to calculate the brightness metrics, which are subsequently provided to the optimization algorithm in DAKOTA that provides new parameters and drives the optimization loop until convergence. In this paper, we show the results of the analysis that are used for the final design of the cylindrical and tube moderator. The optimization simulations provide a refinement to and confirmation of the conclusions of the previous design iteration. Additional to the optimization, a sensitivity study is performed to study the effect of minor geometry changes, which is important for the final engineering design. In conclusion, with these studies, we demonstrate that the automated workflow and high-fidelity unstructured mesh modeling are efficient tools for a thorough design evaluation.

DAKOTA↗
NASA NTRS1976

Characteristics of USB noise

An extensive series of noise measurements, for a variety of geometric and operational parameters, was made on models of upper surface blowing (USB) powered lift systems. The data obtained were analyzed and the effects and trends of parametric variation defined. The behavior and nature of USB noise and the design of USB systems with low noise characteristics is examined.

Gibson, J. S.↗
NASA NTRS1983

Wrinkling phenomenon in structures. I - Model formulations

Those structural element models which can suffer the wrinkling phenomenon are analyzed. A laminated elastic material, defined as a one-parametrical family of surfaces whose in-plane strains are negligible in comparison to the strains in the transverse direction, is analyzed in terms of its geometry, geometrical compatibility equations, layer geometry, kinematics, kinematical compatibility equations, and governing dynamical equations. These aspects are also examined for the case of a soft shell, defined as a shell for which the in-plane strains of the middle surface are negligible compared to the strains in the transverse direction, and for the case of a soft rod, defined as a rod for which the strains along the axis are negligible compared to the strains in the transverse direction. The influence of internal fluid flow on the wrinkling phenomenon for layers of laminated material and for a flexible pipe containing an inviscid and incompressible fluid is also analyzed.

Zak, M.↗
NASA NTRS1995

Computing Stresses In Spur Gears

Dynamic Analysis of Spur Gear Transmissions (DANST) developed as easy-to-use program for static and dynamic analysis of spur-gear systems. Used for parametric studies to predict effects of operating speed, torque, stiffness, damping, inertia, and tooth profile on dynamic loads and tooth-bending stresses in spur gears. Performs geometric modeling and dynamic analysis for low- or high-contact-ratio spur gears. Simulates gear systems with contact ratios ranging from one to three. Written in FORTRAN 77.

Oswald, F. B.↗
NASA NTRS2006

Variable Stiffness Panel Structural Analyses With Material Nonlinearity and Correlation With Tests

Results from structural analyses of three tow-placed AS4/977-3 composite panels with both geometric and material nonlinearities are presented. Two of the panels have variable stiffness layups where the fiber orientation angle varies as a continuous function of location on the panel planform. One variable stiffness panel has overlapping tow bands of varying thickness, while the other has a theoretically uniform thickness. The third panel has a conventional uniform-thickness [plus or minus 45](sub 5s) layup with straight fibers, providing a baseline for comparing the performance of the variable stiffness panels. Parametric finite element analyses including nonlinear material shear are first compared with material characterization test results for two orthotropic layups. This nonlinear material model is incorporated into structural analysis models of the variable stiffness and baseline panels with applied end shortenings. Measured geometric imperfections and mechanical prestresses, generated by forcing the variable stiffness panels from their cured anticlastic shapes into their flatter test configurations, are also modeled. Results of these structural analyses are then compared to the measured panel structural response. Good correlation is observed between the analysis results and displacement test data throughout deep postbuckling up to global failure, suggesting that nonlinear material behavior is an important component of the actual panel structural response.

Wu, K. Chauncey↗
NASA NTRS1993

CFD mixing analysis of axially opposed rows of jets injected into confined crossflow

A computational fluid dynamics (CFD) parametric study was performed to analyze axially opposed rows of jets mixing with crossflow in a rectangular duct. Isothermal analysis was conducted to determine the influence of lateral geometric arrangement on mixing. Two lateral arrangements were analyzed: (1) inline (jets' centerlines aligned with each other on top and bottom walls), and (2) staggered (jets' centerlines offset with each other on top and bottom walls). For a jet-to-mainstream mass flow ratio (MR) of 2.0, design parameters were systematically varied for jet-to-mainstream momentum-flux ratios (J) between 16 and 64 and orifice spacing-to-duct height ratios (S/H) between 0.125 and 1.5. Comparisons were made between geometries optimized for S/H at a specified J. Inline configurations had a unique spacing for best mixing at a specified J. In contrast, staggered configurations had two 'good mixing' spacings for each J, one corresponding to optimum inline spacing and the other corresponding to optimum non-impinging jet spacing. The inline configurations, due to their smaller orifice size at optimum S/H, produced better initial mixing characteristics. At downstream locations (e.g. x/H of 1.5), the optimum non-impinging staggered configuration produced better mixing than the optimum inline configuration for J of 64; the opposite results were observed for J of 16. Increasing J resulted in better mixing characteristics if each configuration was optimized with respect to orifice spacing. Mixing performance was shown to be similar to results from previous dilution jet mixing investigations (MR less than 0.5).

Bain, D. B.↗
NASA NTRS1986

Influence of third-degree geometric nonlinearities on the vibration and stability of pretwisted, preconed, rotating blades

The governing coupled flapwise bending, edgewise bending, and torsional equations are derived including third-degree geometric nonlinear elastic terms by making use of the geometric nonlinear theory of elasticity in which the elongations and shears are negligible compared to unity. These equations are specialized for blades of doubly symmetric cross section with linear variation of pretwist over the blade length. The nonlinear steady state equations and the linearized perturbation equations are solved by using the Galerkin method, and by utilizing the nonrotating normal modes for the shape functions. Parametric results obtained for various cases of rotating blades from the present theoretical formulation are compared to those produced from the finite element code MSC/NASTRAN, and also to those produced from an in-house experimental test rig. It is shown that the spurious instabilities, observed for thin, rotating blades when second degree geometric nonlinearities are used, can be eliminated by including the third-degree elastic nonlinear terms. Furthermore, inclusion of third degree terms improves the correlation between the theory and experiment.

Subrahmanyam, K. B.↗
NASA NTRS1987

Influence of third-degree geometric nonlinearities on the vibration and stability of pretwisted, preconed, rotating blades

The governing coupled flapwise bending, edgewise bending, and torsional equations are derived including third-degree goemetric nonlinear elastic terms by making use of the geometric nonlinear theory of elasticity in which the elongations and shears are negligible compared to unity. These equations are specialized for blades of doubly symmetric cross section with linear variation of Pretwist over the blade length. The nonlinear steady state equations and the linearized perturbation equations are solved by using the Galerkin method, and by utilizing the nonrotating normal modes for the shape functions. Parametric results obtained for various cases of rotating blades from the present theoretical formulation are compared to those produced from the finite element code MSC/NASTRAN, and also to those produced from an in-house experimental test rig. It is shown that the spurious instabilities, observed for thin, rotating blades when second degree geometric nonlinearities are used, can be eliminated by including the third-degree elastic nonlinear terms. Furthermore, inclusion of third degree terms improves the correlation between the theory and experiment.

Subrahmanyam, K. B.↗
NASA NTRS1993

Dynamic analysis of spur gears using computer program DANST

DANST is a computer program for static and dynamic analysis of spur gear systems. The program can be used for parametric studies to predict the effect on dynamic load and tooth bending stress of spur gears due to operating speed, torque, stiffness, damping, inertia, and tooth profile. DANST performs geometric modeling and dynamic analysis for low- or high-contact-ratio spur gears. DANST can simulate gear systems with contact ratio ranging from one to three. It was designed to be easy to use, and it is extensively documented by comments in the source code. This report describes the installation and use of DANST. It covers input data requirements and presents examples. The report also compares DANST predictions for gear tooth loads and bending stress to experimental and finite element results.

Oswald, Fred B.↗
NASA NTRS1993

CFD mixing analysis of axially opposed rows of jets injected into confined crossflow

A CFD parametric study was performed to analyze axially opposed rows of jets mixing with crossflow in a rectangular duct. An isothermal analysis was conducted to determine the influence of lateral geometric arrangement on mixing for the cases of: (1) inline (jets' centerlines aligned with each other on top and bottom walls), and (2) staggered (jets' centerlines offset with each other on top and bottom walls) configurations. For a jet-to-mainstream mass flow ratio (MR) of 2.0, design parameters were systematically varied for jet-to-mainstream momentum-flux ratios (J) between 16 and 64 and orifice spacing-to-duct height ratios (S/H) between 0.125 and 1.5. Comparisons were made between geometries optimized for S/H at a specified J. Inline configurations had a unique spacing for best mixing at a specified J. In contrast, staggered configurations had two 'good mixing' spacings for each J, one corresponding to optimum inline spacing and the other corresponding to optimum nonimpinging jet spacing. Increasing J resulted in better mixing characteristics if each configuration was optimized with respect to orifice spacing. Mixing performance was shown to be similar to results from previous dilution jet mixing investigations (MR less than 0.5).

Bain, D. B.↗