SEARCH · Search NASA

Results for “Geometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS1983

Characterization of the matrix glass transition in carbon-epoxy laminates using the CSD test geometry

A new test geometry, referred to as centro-symmetric deformation (CSD), is proposed for characterizing the viscoelastic behavior of the matrix of carbon-epoxy laminates. The sample consists of a thin disk, typically 6-14 plies thick, having a nominal diameter of 30 mm. The disk is freely supported on a circular anvil; the load is applied to the center of the disk using an 8-mm-diameter ball bearing nosepiece. The CSD test geometry provides viscoelastic dispersion data which are independent of the angular orientation of the sample. The test geometry is sufficiently sensitive to matrix changes to allow its use for postcuring, humidity, crosslink density, and other matrix change studies. Test results are presented for a carbon-epoxy laminate.

Sternstein, S. S.↗

NASA NTRS1984

Computer-Aided Geometry Modeling

Techniques in computer-aided geometry modeling and their application are addressed. Mathematical modeling, solid geometry models, management of geometric data, development of geometry standards, and interactive and graphic procedures are discussed. The applications include aeronautical and aerospace structures design, fluid flow modeling, and gas turbine design.

John N. Shoosmith↗

NASA NTRS1984

A geometric modeler based on a dual-geometry representation polyhedra and rational b-splines

For speed and data base reasons, solid geometric modeling of large complex practical systems is usually approximated by a polyhedra representation. Precise parametric surface and implicit algebraic modelers are available but it is not yet practical to model the same level of system complexity with these precise modelers. In response to this contrast the GEOMOD geometric modeling system was built so that a polyhedra abstraction of the geometry would be available for interactive modeling without losing the precise definition of the geometry. Part of the reason that polyhedra modelers are effective is that all bounded surfaces can be represented in a single canonical format (i.e., sets of planar polygons). This permits a very simple and compact data structure. Nonuniform rational B-splines are currently the best representation to describe a very large class of geometry precisely with one canonical format. The specific capabilities of the modeler are described.

Klosterman, A. L.↗

NASA NTRS1984

Geometry Software Common to All Experiments

All imaging, remote sensing, and in situ experiments require information about the geometry and location of observations. An alterntive to collecting geometry data with a supplementary experiment data record is proposed. The new method involves identifying the fundamental information, that is, the geometric state upon which geometry calculations are based, and maintaining or delivering these calculations in separate packages which are easily replaced when improved information is available. Implementation of this method in spacecraft navigation is discussed along with software system requirements.

Source record↗

NASA NTRS1982

Jet array impingement flow distributions and heat transfer characteristics: Effects of initial crossflow and nonuniform array geometry

Flow distributions and heat transfer characteristics for two-dimensional arrays of circular air jets impinging on a surface parallel to the jet orifice plate were determined. The configurations considered were intended to model those of interest in current and contemplated gas turbine airfoil midchord cooling applications. The geometry of the airfoil applications considered dictates that all of the jet flow, after impingement, exit in the chordwise (i.e., streamwise) direction toward the trailing edge. Experimental results for the effect of an initial crossflow on both flow distributions and heat transfer characteristics for a number of the prior uniform array geometries. The effects of nonuniform array geometries on flow distributions and heat transfer characteristics for noninitial crossflow configurations are discussed.

Florschuetz, L. W.↗

NASA NTRS1985

Flow visualization study of the effect of injection hole geometry on an inclined jet in crossflow

A flow visualization was studied by using neutrally buoyant, helium-filled soap bubbles, to determine the effect of injection hole geometry on the trajectory of an air jet in a crossflow and to investigate the mechanisms involved in jet deflection. Experimental variables were the blowing rate, and the injection hole geometry cusp facing upstream (CUS), cusp facing downstream (CDS), round, swirl passage, and oblong. It is indicated that jet deflection is governed by both the pressure drag forces and the entrainment of free-stream fluid into the jet flow. For injection hole geometries with similar cross-sectional areas and similar mass flow rates, the jet configuration with the larger aspect ratio experienced a greater deflection. Entrainment arises from lateral shearing forces on the sides of the jet, which set up a dual vortex motion within the jet and thereby cause some of the main-stream fluid momentum to be swept into the jet flow. This additional momentum forces the jet nearer the surface. Of the jet configurations, the oblong, CDS, and CUS configutations exhibited the largest deflections. The results correlate well with film cooling effectiveness data, which suggests a need to determine the jet exit configuration of optimum aspect ratio to provide maximum film cooling effectiveness.

Simon, F. F.↗

NASA NTRS1985

Analytical study of flow phenomena in SSME turnaround duct geometries

The SSME fuel turbopump hot gas manifold was identified as a source of loss and flow distortion which significantly affects the performance and durability of both the drive turbine and the LOX injector area of the main combustion chamber. Two current SSME geometries were studied, the full power level (FPL) and the first manned orbital flight (FMOF) configuration. The effects of turnaround duct geometry on flow losses and distortions, by varying wall curvature and flow area variation in the 180 deg turnaround region were examined. The effects of the duct inlet flow phenomena such as the radial distortion of the inlet flow and inlet swirl level on turnaround duct performance were also investigated. It is shown that of the two current geometries, the FMOF configuration had lower pressure losses and generated less flow distortion, but had a small flow separation bubble at the 180 deg turnaround exit. It is found that by optimizing wall curvature and flow diffusion in the turnaround, improved duct performance can be achieved.

Mclallin, K. L.↗

NASA NTRS1984

Generalized wake geometry for a helicopter in forward flight and effect of wake deformation on airloads

An analytical investigation was conducted to develop a first level generalization of the predicted distorted wake geometry of a helicopter rotor in level steady forward flight and to demonstrate the influence of wake deformation on the prediction of rotor airloads. Distortions of the tip vortex relative to the classical undistorted geometry are generalized in terms of vortex age, blade azimuth, advance ratio, thrust coefficient, and number of blades for a representative rotor. A computer module and charts were developed for approximating wake geometry and identifying wake boundaries and locations of blade-vortex passage. Predicted H-34 airloads for several inflow/wake models are compared with data for selected flight conditions. The occurrence of close blade-vortex passages and the high sensitivity of predicted airloads to small deviations of blade to tip vortex distance demonstrate the requirement for improved blade-vortex interaction models. The airload correlations indicate that refined distorted wake methodology has the potential to provide more accurate airload prediction.

Egolf, T. A.↗

NASA NTRS1985

Application of the SWINT code to wing/body/tail geometries

Pressure and force calculations from the SWINT Euler code are presented and analyzed for a variety of configurations ranging from simple axisymmetric bodies to complex bodies with wings, tails, and inlets at speeds covering the supersonic Mach number range. The SWINT results are compared with both experimental data and with results from simpler computational methods to assess the increased accuracy from the Euler solution. It is shown that SWINT gives excellent results on axisymmetric bodies for attached flow; however, a better method of simulating the separation process on such bodies is needed for increased leeside accuracy. Good leeside accuracy, however, is found on a 3 to 1 elliptical body. It is shown that SWINT gives realistic downstream interference effects, resulting in good predictions of the overall aerodynamics for complex wing-body-tail geometries. The QUICK-geometry system has been coupled with SWINT code to provide a simplified geometry definition procedure for complex bodies. The QUICK method is shown to be a preferable alternative to the current method of inserting the body description directly into the code by FORTRAN statements.

Allen, J. M.↗

NASA NTRS1985

Ellipsoidal geometry in asteroid thermal models - The standard radiometric model

The major consequences of ellipsoidal geometry in an othewise standard radiometric model for asteroids are explored. It is shown that for small deviations from spherical shape a spherical model of the same projected area gives a reasonable aproximation to the thermal flux from an ellipsoidal body. It is suggested that large departures from spherical shape require that some correction be made for geometry. Systematic differences in the radii of asteroids derived radiometrically at 10 and 20 microns may result partly from nonspherical geometry. It is also suggested that extrapolations of the rotational variation of thermal flux from a nonspherical body based solely on the change in cross-sectional area are in error.

Brown, R. H.↗

NASA NTRS1986

Acoustic properties associated with rectangular geometry supersonic nozzles

Acoustic property experiments have been conducted to ascertain the behavior of rectangular geometry supersonic nozzles whose throat aspect ratios vary over a 2.0-7.6 range, and whose three partial sidewall geometries range from full to 75-percent cutback. The tests employed unheated air at static conditions for nozzle Mach numbers of 1.35-1.66. It is found that sonic fatigue failures are possible at certain partial sidewall geometries and high nozzle aspect ratios. Unlike axisymmetric supersonic nozzles, shock noise dominates both the rear and forward arc for throat aspect ratio cases greater than 5.6. Jet screech frequency was adequately predicted with a simple vortex sheel model.

Seiner, J. M.↗

NASA NTRS1987

Flow visualization study of the effect of injection hole geometry on an inclined jet in crossflow

A flow visualization was studied by using neutrally buoyant, helium-filled soap bubbles, to determine the effect of injection hole geometry on the trajectory of an air jet in a crossflow and to investigate the mechanisms involved in jet deflection. Experimental variables were the blowing rate, and the injection hole geometry cusp facing upstream (CUS), cusp facing downstream (CDS), round, swirl passage, and oblong. It is indicated that jet deflection is governed by both the pressure drag forces and the entrainment of free-stream fluid into the jet flow. For injection hole geometries with similar cross-sectional areas and similar mass flow rates, the jet configuration with the larger aspect ratio experienced a greater deflection. Entrainment arises from lateral shearing forces on the sides of the jet, which set up a dual vortex motion within the jet and thereby cause some of the main-stream fluid momentum to be swept into the jet flow. This additional momentum forces the jet nearer the surface. Of the jet configurations, the oblong, CDS, and CUS configurations exhibited the largest deflections. The results correlate well with film cooling effectiveness data, which suggests a need to determine the jet exit configuration of optimum aspect ratio to provide maximum film cooling effectiveness.

Simon, Frederick F.↗

NASA NTRS1987

Numerical solution of the radiation transport equation in disk geometry

An efficient numerical method for solving the problem of radiation transport in a dusty medium with two dimensional (2-D) disk geometry is described. It is a generalization of the one-dimensional quasi-diffusion method in which the transport equation is cast in diffusion form and then solved as a boundary value problem. The method should be applicable to a variety of astronomical sources, the dynamics of which are angular-momentum dominated and hence not accurately treated by spherical geometry, e.g., protoplanetary nebulae, circumstellar disks, interstellar molecular clouds, accretion disks, and disk galaxies. The computational procedure and practical considerations for implementing the method are described in detail. To illustrate the effects of 2-D radiation transport, some model results (dust temperature distributions and IR flux spectra) for externally heated, interstellar dust clouds with spherically symmetric and disk geometry are compared.

Spagna, George F., Jr.↗

NASA NTRS1987

A variable geometry combustor for broadened properties fuels

A program was conducted to design and develop a variable geometry combustor, sized for the cycle and envelope of a large commercial turbofan engine. The combustor uses a variable area swirl cup to control stoichiometry in the primary combustion zone. Potential advantages of this design include improved capability to burn non-standard fuels, short system length, and increased operating temperature range for advanced high performance engine cycles. After considerable development, key program emissons and performance goals were met with the variable geometry combustor. Primary development efforts were to evolve improved variable swirl cup configurations. In particular, air leakage through the variable area swirl cup had a strong effect on low power emissions and performance, while smoke level at high power was affected by features for improved mixing of the fuel and swirler air flow. Additional design and development is still needed to evolve a practical variable geometry combustor.

Dodds, W. J.↗

NASA NTRS1988

An interactive user-friendly approach to surface-fitting three-dimensional geometries

A surface-fitting technique has been developed which addresses two problems with existing geometry packages: computer storage requirements and the time required of the user for the initial setup of the geometry model. Coordinates of cross sections are fit using segments of general conic sections. The next step is to blend the cross-sectional curve-fits in the longitudinal direction using general conics to fit specific meridional half-planes. Provisions are made to allow the fitting of fuselages and wings so that entire wing-body combinations may be modeled. This report includes the development of the technique along with a User's Guide for the various menus within the program. Results for the modeling of the Space Shuttle and a proposed Aeroassist Flight Experiment geometry are presented.

Cheatwood, F. Mcneil↗

NASA NTRS1988

An automated computerized vision technique for determination of three-dimensional object geometry

It is very important to determine three dimensional geometry of objects quickly in various military, space, construction, and industrial applications. An automatic scheme to obtain three dimensional geometry of objects by employing only one camera is presented. At present, this technique is applicable to a limited category of objects, satisfying the following constraints: they are flat-surfaces, and all the vertex points have to be recognized as corner points of the two dimensional image. The scheme consists of corner detection, data communication, camera calibration techniques and point searching and matching, edge cancelation, and creation procedures. An L shaped model is chosen as a test object. Experimental results demonstrated the reconstruction of this object geometry within 5 mm discrepancy. This scheme is quite convenient, efficient to use and can be applied to a wide range of problems in the real world.

Chiang, Pen-Tai↗

NASA NTRS1988

A multi-element vortex lattice method for calculating the geometry and effects of a helicopter rotor wake in forward flight

A method is described for the analysis of the unsteady, incompressible potential flow associated with a helicopter rotor and it's wake in forward flight. This method is particularly useful in low advance ratio flight due to the major contribution, in the near field, of the deformed wake. The rotor geometry is prescribed and the unsteady wake geometry is computed from the local flow perturbation velocities. The wake is modeled as a full vortex lattice. The rotor geometry is arbitrary and several rotor blades can be represented. The unsteady airloads on the rotor blades are computed in the presence of the deformed rotor wake by a time-stepping technique. Solution for the load distribution on the blade surfaces is found by prescribing boundary conditions in a reference system which rotates with the blade tips. Transformation tensors are used to describe the contribution of the wake in the inertial system to the rotor in the rotating reference system. The effects of blade cyclic pitch variation are computed using a rotation tensor. The deformation of the wake is computed in the inertial frame. The wake is started impulsively from rest, allowing a natural convection of the wake with time.

Berry, John D.↗

NASA NTRS1988

Erupting prominences and the geometry of coronal mass ejections

Studies of the origins of coronal mass ejections (CMEs) show a strong association between CMEs and erupting prominences. 'Loop' CMEs form the most common morphological class for both Skylab and Solar Maximum Mission (SMM) and the class most likely to be associated with erupting prominences. In the optically thin corona, the geometry of such structures is interpreted as either planar (two-dimensional), shell-like, or bubblelike (three-dimensional) structures. Trottet and MacQueen (1980) (hereinafter referred to as TM) first examined the orientations of prominences associated with Skylab CMEs and argued that looplike CMEs were planar structures in the plane of the sky. In this work, the initial orientations of prominences identified with SMM CMEs in 1980 were measured in order to examine the overall geometry of CMEs. Contrary to TM's result, no preferred orientation for prominences associated with SMM CMEs nor any difference between that population and the population of all disk filaments were found. In addition, plots comparing CME/filament orientation angles and the angular widths of the CME envelopes show large scatter. Taken together, these results support a shell-like rather than a planar geometry for at least looplike CMEs.

Webb, David F.↗