Search NASA⌕ Search

SEARCH · Search NASA

Results for “Gradient Limiters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Fatigue Testing and Characterization of Pre-hydrided Zircaloy-4 Cladding Tubes

The solubility of hydrogen in Zircaloy-4 (Zry-4) at the cladding operating temperature is near 100 wt. ppm. Above this solubility limit, excess hydrogen precipitates as δ-hydride platelets in the cladding material. Because of the effect of the thermal gradient across the cladding thickness on the migration and precipitation of hydrogen, hydride rims are often observed at the cladding outer surface; under excessive corrosion conditions hydride blisters are possible. It is well known that the fatigue of metal alloys, especially high cycle fatigue, is sensitive to the status of surface including the microstructure, roughness, and residual stress. Thus, the question considered herein, is whether excessive hydrogen pickup modifies the microstructure such that it has a degradation effect on the fatigue performance of cladding during operation. This report describes the evaluation of fatigue performance of a pre-hydrided Zry-4 cladding. A commercial Zry-4 was polished and pre-hydrided to 800 ppm and 1300 ppm H contents. The fatigue testing was conducted under strain control at 5 Hz with fully-reversed bending by using a cyclic integrated reversible bending fatigue tester (CIRFT). Six specimens with 1300 ppm and one specimen with 800 ppm were tested. Significant variation in test results were observed. While two of the 1300 ppm specimens failed with less than 1 ×10 5 cycles (at 0.32% and 0.41%), the four other samples did not fail over the strain amplitude range of 0.25% to 0.38%. Interestingly, the fracture initiation site of the failed samples was on the outside diameter (OD) surface rather than on the inside diameter (ID) surface as is typical for the as-polished cladding. This suggested a degrading effect of the hydriding process. Subsequently, three of the unfailed specimens were then further tested at ~0.43% to observe where failure initiation occurred. Significant variation was also observed in these three specimens. One specimen failed at ~9000 cycles while the two others failed at 43000 and 1.06 ×10 5 cycles. The performance here correlated to the location of failure initiation; failure initiated on the OD in the sample that failed after 9000 cycles while it initiated on the ID in the sample that failed after 43000 and 1.06 ×10 5 cycles. Flat features at the OD initiation sites suggest a brittle hydride feature on the surface of those samples was the cause of the degradation in fatigue performance, though the overall hydrogen levels in all samples was similar. A summary of all the observations is provided below: • The un-failed specimens with 1300 ppm H were cycled to failure with a higher amplitude near 0.43%. In addition, the fatigue-treated specimen tended to have a longer fatigue at the same induced amplitude. • Fractography revealed a mixed failure mode for the pre-hydrided specimen. Particularly, the specimen with fracture initiation site (FIS) located on the outer diameter surface of tube tended to have a shorter fatigue life than that of FIS on the inner diameter surface. • Etched cross section was shown to have hydride platelets aligned with tube longitudinal axis as expected, and the density of hydrides is at the similar level as in literature data. Meanwhile, a LECO procedure was applied for hydrogen concentration measurement, which showed the measured hydrogen contents are close to the nominal value. • With the polished cladding tube as baseline, O’Donnell-Lager (O-L) analysis showed that a decrease of about 50% in reduction-of-area (RA) would be needed for the O-L fitting to the fatigue data of 1300 ppm cladding. The suggestion for the next steps is provided.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Toward Complete Merger Identification at Cosmic Noon with Deep Learning

As we enter the era of large imaging surveys such as Roman, Rubin, and Euclid, a deeper understanding of potential biases and selection effects in optical astronomical catalogs created with the use of ML-based methods is paramount. This work focuses on a deeper understanding of the performance and limitations of deep learning-based classifiers as tools for galaxy merger identification. We train a ConvNeXT-Pico model on mock HST CANDELS images from the IllustrisTNG50 simulation. Our focus is on a more challenging classification of galaxy mergers and non-mergers at higher redshifts 1 < z < 1.5, including minor mergers and lower mass galaxies down to the stellar mass of 108M⊙. We demonstrate, for the first time, that a deep learning model, such as the one developed in this work, can successfully identify even minor and low mass mergers even at these redshifts. Our model achieves overall accuracy, purity, and completeness of over 73%. We show that some galaxy mergers can only be identified from certain observation angles, leading to a potential upper limit in overall accuracy. Using Grad-CAMs and UMAPs, we more deeply examine the performance and observe a visible gradient in the latent space with stellar mass and specific star formation rate, but no visible gradient with merger mass ratio or merger stage.

Schechter, Aimee L. [U. Colorado, Boulder]↗
DOE OSTI2024

Overview of ASDEX upgrade results in view of ITER and DEMO

Experiments on ASDEX Upgrade (AUG) in 2021 and 2022 have addressed a number of critical issues for ITER and EU DEMO. A major objective of the AUG programme is to shed light on the underlying physics of confinement, stability, and plasma exhaust in order to allow reliable extrapolation of results obtained on present day machines to these reactor-grade devices. Concerning pedestal physics, the mitigation of edge localised modes (ELMs) using resonant magnetic perturbations (RMPs) was found to be consistent with a reduction of the linear peeling-ballooning stability threshold due to the helical deformation of the plasma. Conversely, ELM suppression by RMPs is ascribed to an increased pedestal transport that keeps the plasma away from this boundary. Candidates for this increased transport are locally enhanced turbulence and a locked magnetic island in the pedestal. The enhanced D-alpha (EDA) and quasi-continuous exhaust (QCE) regimes have been established as promising ELM-free scenarios. Here, the pressure gradient at the foot of the H-mode pedestal is reduced by a quasi-coherent mode, consistent with violation of the high-n ballooning mode stability limit there. This is suggestive that the EDA and QCE regimes have a common underlying physics origin. In the area of transport physics, full radius models for both L- and H-modes have been developed. These models predict energy confinement in AUG better than the commonly used global scaling laws, representing a large step towards the goal of predictive capability. A new momentum transport analysis framework has been developed that provides access to the intrinsic torque in the plasma core. In the field of exhaust, the X-Point Radiator (XPR), a cold and dense plasma region on closed flux surfaces close to the X-point, was described by an analytical model that provides an understanding of its formation as well as its stability, i.e., the conditions under which it transitions into a deleterious MARFE with the potential to result in a disruptive termination. With the XPR close to the divertor target, a new detached divertor concept, the compact radiative divertor, was developed. Here, the exhaust power is radiated before reaching the target, allowing close proximity of the X-point to the target. No limitations by the shallow field line angle due to the large flux expansion were observed, and sufficient compression of neutral density was demonstrated. With respect to the pumping of non-recycling impurities, the divertor enrichment was found to mainly depend on the ionisation energy of the impurity under consideration. In the area of MHD physics, analysis of the hot plasma core motion in sawtooth crashes showed good agreement with nonlinear 2-fluid simulations. This indicates that the fast reconnection observed in these events is adequately described including the pressure gradient and the electron inertia in the parallel Ohm’s law. Concerning disruption physics, a shattered pellet injection system was installed in collaboration with the ITER International Organisation. Thanks to the ability to vary the shard size distribution independently of the injection velocity, as well as its impurity admixture, it was possible to tailor the current quench rate, which is an important requirement for future large devices such as ITER. Progress was also made modelling the force reduction of VDEs induced by massive gas injection on AUG. The H-mode density limit was characterised in terms of safe operational space with a newly developed active feedback control method that allowed the stability boundary to be probed several times within a single discharge without inducing a disruptive termination. Regarding integrated operation scenarios, the role of density peaking in the confinement of the ITER baseline scenario (high plasma current) was clarified. The usual energy confinement scaling ITER98(p,y) does not capture this effect, but the more recent H20 scaling does, highlighting again the importance of developing adequate physics based models. Advanced tokamak scenarios, aiming at large non-inductive current fraction due to non-standard profiles of the safety factor in combination with high normalised plasma pressure were studied with a focus on their access conditions. A method to guide the approach of the targeted safety factor profiles was developed, and the conditions for achieving good confinement were clarified. Based on this, two types of advanced scenarios (‘hybrid’ and ‘elevated’

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Comparison between Alcator C-Mod ICRF experiments and 3D full wave simulations

Reliable modeling of ion cyclotron range of frequencies (ICRF) antenna performance is essential for interpreting present experiments and guiding the design of future reactors. In this work, a 3D model of the Alcator C-Mod field-aligned antenna is implemented in the Petra-M finite-element framework [S. Shiraiwa et al 2023 Nucl. Fusion 63 026024] and benchmarked against experimental results. Four experimental cases are examined. First, the simulated rectified sheath potentials on the antenna limiters are compared with measurements from a power tapering experiment. Second, proof-of-principle far-field sheath simulations are performed. In scenarios with low single-pass absorption, simulations predict enhanced sheath potentials on a distant poloidal limiter in the far field of the antenna, consistent with experimental observations. Third, the simulated antenna loading during edge localized modes follows experimental trends and appears to be dominated by the density gradient at the pedestal. Finally, Petra-M predicts the unintended excitation of high-$k$ ∥ modes during monopole phasing operation, in agreement with experimental evidence of poor wave coupling and accessibility to the plasma core. Overall, reasonable agreement is found between the simulations and experiments. At the same time, areas of imperfect agreement are identified. These provide important guidance on the limits of the current state-of-the-art modeling, which should be kept in mind when using it as a predictive tool for future reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

High-compression implosions based on high density carbon ablator using modified drive and capsule dopant profiles

Laser-driven inertial fusion experiments have, for the first time, achieved a target gain greater than unity in a laboratory setting [Abu-Shawareb et al., Phys. Rev. Lett. 132, 065102 (2024)]. Despite this breakthrough, the burn-up fraction remains limited to about one-fourth of ideal estimates due to insufficient areal density, highlighting the potential for greater gains through enhanced compression. In our previous work, we demonstrated record-high compression of stagnated fuel in indirectly driven implosions using high-density carbon ablators. This was achieved by combining a continuous ramped pulse drive with a modified ablator dopant profile, which reduced mixing at the fuel–ablator interface and improved stability [Tommasini et al., Phys. Rev. Res. 5, L042034 (2023)]. Based on this foundation, the study presented here investigates the limits of compression achievable by combining the continuous ramped pulse drive with different dopant profiles to further minimize unstable interfaces and gradient discontinuities, thereby reducing fuel–ablator mixing. Our results demonstrate that the continuous ramped pulse consistently outperforms designs based on 3-shock drive pulses across all ablator profiles studied, with compression showing only a relatively modest dependence on dopant configurations that reduce the number of interfaces or eliminate discontinuities in the dopant gradient profile. Sub-scale experiments using the continuous ramped pulse achieved compression levels exceeding those of full-scale “HyE” implosions [Kritcher et al., Phys. Plasmas 28, 072706 (2021)] at similar adiabat, anticipating significant performance gains with increased scale, as supported by models and simulations. These findings underscore the critical role of the continuous ramped pulse in reducing mix and achieving improved compression. They also provide a foundation for future large-scale experiments to test the continuous ramped pulse design on deuterium–tritium fuel in the burn-wave propagation regime, leveraging the most effective combinations of continuous ramped pulse and dopant profiles identified in this study.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Characterizing impurity sourcing and transport in the high temperature boundary of DIII-D wide pedestal QH-mode plasmas

Wide Pedestal QH-mode (WPQH) plasmas in the DIII-D tokamak show a sheath limited SOL, where electron density and temperature remain nearly constant along field lines from the midplane to the divertor. Consequently, parallel gradients are weak. The first Langmuir probe measurements in this regime point to a high sheath temperature with target electron temperature T e up to ~150 eV, leading to high carbon self-sputtering. Midplane carbon densities from SOLPS-ITER modeling of these plasmas in a double-null configuration fall far below experimental measurements unless full drifts are activated. In the drift-dependent SOLPS-ITER modeling, anomalous poloidally uniform, radially varying transport is adjusted to match measured radial electron temperature and density profiles in the pedestal and SOL region. The resulting carbon density (C6+) matches measured carbon densities just inside the separatrix. The C2+ density near the outer strike point is also consistent with spectroscopic imaging. With the ion B×∇B drift towards the X-point, carbon in the lower divertors is redistributed from the private flux region to the high field side (HFS) and pushed upstream in the SOL by poloidal E×B drifts. The B × ∇B drift dominates the radial flow of carbon as it moves upstream. Simulations with reversed toroidal field (ion B × ∇B drift away from the X-point) show a radically different behavior, where carbon accumulates on the low field side in lower divertors, and is pushed towards the HFS in the upper divertors, indicating a strong effect of particle drifts on impurity distribution. In double-null configurations which are usually used in WPQH plasmas, these drift effects tend to counterbalance, so that the carbon density and Z eff are reduced at the outer mid-plane only modestly, by around 7% in the modeling. Further predictive modeling indicates that the carbon density can be significantly reduced by an order of magnitude by implementing a single-null shape with reversed toroidal field.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Understanding particle size effect on fast-charging behavior of graphite anode using ultra-thin-layer electrodes

Extreme fast charging (≤ 15 min) of lithium-ion batteries is highly desirable to accelerate mass-market adoption of electric vehicles. However, significant capacity fading, as well as safety issues due to the lithium plating caused by the fast charging rate, limit its implementation. In this study, we investigated the fast-charging capability of graphite materials with various particle sizes. To eliminate the Li + ion concentration gradient effect across the thickness of the electrode, ultra-thin-layer graphite electrodes were developed to investigate the "real" fast-charging capability of graphite at the particle level. Electrochemical assessments as well as microscopic characterizations revealed that smaller particles exhibited superior fast-charging performance, featuring enhanced capacity reversibility, faster charging rate, and less lithium plating under the same fast-charging conditions. It is shown that small-particle graphite (mean radius of 3.3 μm) could withstand a 4C charge (to 80 % state-of-charge) without plating, with minimal plating occurring at 6C. Thicker particles exhibited plating at lower C-rates. Since the experimental data could not directly explain whether intra-particle diffusion limitations or interfacial reaction limitations dominated the plating mechanism, the pseudo-2-dimensional model was used to evaluate the most likely plating mechanism. The model suggested that particle-level diffusion is the dominant mechanism contributing to plating at high rates. Finally, this work provides comprehensive insights into the particle size effects on fast-charging capability, offering a better understanding of fast-charging behavior and valuable guidance for designing optimal electrode architecture for high-rate lithium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2026

Calcium Gradient-Doped LiNi 0.5 Mn 1.5 O 4 Cathode for Long Cycle Life Lithium-Ion Batteries

High-voltage spinel LiNi 0.5 Mn 1.5 O 4 (LNMO) has attracted considerable attention as a cathode material for next-generation lithium-ion batteries due to its high operating voltage and intrinsically fast lithium-ion diffusion kinetics. However, the practical implementation of LNMO remains limited by its rapid capacity decay, primarily associated with bulk structural instability and parasitic interfacial reactions. To address these issues, we innovatively introduced calcium (Ca) as a dopant to enhance both the oxygen framework and surface stabilities of the LNMO crystal through gradient doping. Observations from the electronic microscopies, X-ray diffraction, and the elemental analysis confirmed that Ca is preferentially enriched at the particle surface, and a disordered crystal phase is preserved in the bulk in the gradient-doped LNMO cathodes. As cathodes in LIBs, the Ca gradient-doped (Ca gr) LNMO materials delivered formation capacities of ∼126−130 mAh/g and exhibited Coulombic efficiencies of 88−95%, which are consistently higher than those of the uniform-doped samples at the same doping level and undoped sample. Especially, the Ca gr 0.05 LNMO cathode demonstrated significantly improved rate capability with ∼113 mAh/g preserved at 10 C, while ∼92 mAh/g and ∼110 mAh/g for undoped and Ca uniform 0.05 LNMO, respectively, and excellent cycling stability, retaining ∼124.1 mAh/g (∼96.3% capacity retention) after 500 cycles. The analysis of cyclic voltammetry, differential capacity, and electrochemical impedance revealed that the excellent electrochemical performance is attributed to the structural and morphological advantages of gradient-doped LNMO cathodes with a disordered bulk structure for fast Li + diffusion and a Ca-enriched surface for minimizing the Mn dissolution.

25 ENERGY STORAGE↗
DOE OSTI2026

Ambient ion focusing from a field-free region to a detector: enhanced signal for explosives and drug detection with mass spectrometry

This study demonstrates ion focusing at ambient pressure and increased ion signal by creating a voltage gradient from a field-free region to a detector, thereby improving the detection of chemicals, such as explosives and drugs. At ambient pressure, ion loss and resulting signal reduction pose challenges that limit detection sensitivity in analytical instruments. Techniques to increase sensitivity, such as atmospheric flow tube-mass spectrometry (AFT-MS), extend ion-molecule reaction times but result in significant overall ion loss due to diffusion. Ion manipulation techniques, though challenging at ambient pressure, can mitigate these losses by concentrating ions toward the detector inlet. Using SIMION, ion trajectories were modeled with a voltage gradient applied between a flow tube and a detector, revealing ion focusing at ambient pressure. Experimental verification with an atmospheric flow tube employed both mass spectrometry and Faraday plate detectors to measure ion beam profiles across varying flow rates, tube diameters, and voltage gradients. Application of a voltage gradient effectively directed ions to the axial center of the flow tube, narrowed ion beam width, and increased signal intensity by 5 to 10 times compared to conditions without a voltage gradient. This ion focusing approach shows promise for improving sensitivity in ambient-pressure instruments. This technique has the potential to enhance detection levels in security and forensic applications, with particular benefits for field-portable devices used at checkpoints to identify explosives and drugs.

ambient pressure↗
DOE OSTI2025

Application of Machine Learning and Data Augmentation Algorithms in the Discovery of Metal Hydrides for Hydrogen Storage

The development of efficient and sustainable hydrogen storage materials is a key challenge for realizing hydrogen as a clean and flexible energy carrier. Among various options, metal hydrides offer high volumetric storage density and operational safety, yet their application is limited by thermodynamic, kinetic, and compositional constraints. In this work, we investigate the potential of machine learning (ML) to predict key thermodynamic properties—equilibrium plateau pressure, enthalpy, and entropy of hydride formation—based solely on alloy composition using Magpie-generated descriptors. We significantly expand an existing experimental dataset from ~400 to 806 entries and assess the impact of dataset size and data augmentation, using the PADRE algorithm, on model performance. Models including Support Vector Machines and Gradient Boosted Random Forests were trained and optimized via grid search and cross-validation. Results show a marked improvement in predictive accuracy with increased dataset size, while data augmentation benefits are limited to smaller datasets and do not improve accuracy in underrepresented pressure regimes. Furthermore, clustering and cross-validation analyses highlight the limited generalizability of models across different material classes, though high accuracy is achieved when training and testing within a single hydride family (e.g., AB2). The study demonstrates the viability and limitations of ML for accelerating hydride discovery, emphasizing the importance of dataset diversity and representation for robust property prediction.

augmentation↗
DOE OSTI2025

Collisionless conduction in a high-beta plasma: a collision operator for whistler turbulence

The regulation of electron heat transport in high-β, weakly collisional, magnetized plasma is investigated. A temperature gradient oriented along a mean magnetic field can induce a kinetic heat-flux-driven whistler instability (HWI), which back-reacts on the transport by scattering electrons and impeding their flow. Previous analytical and numerical studies have shown that the heat flux for the saturated HWI scales as β$^{-1}_{e}$. These numerical studies, however, had limited scale separation and consequently large fluctuation amplitudes, which calls into question their relevance at astrophysical scales. To this end, we perform a series of particle-in-cell simulations of the HWI across a range of β$_e$ and temperature-gradient length scales under two different physical set-ups. The saturated heat flux in all of our simulations follows the expected β$^{-1}_{e}$ scaling, supporting the robustness of the result. We also use our simulation results to develop and implement several methods to construct an effective collision operator for whistler turbulence. The results point to an issue with the standard quasi-linear explanation of HWI saturation, which is analogous to the well-known 90° scattering problem in the cosmic-ray community. Despite this limitation, the methods developed here can serve as a blueprint for future work seeking to characterize the effective collisionality caused by kinetic instabilities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Gradient-based optimization of complex nanoparticle heterostructures enabled by deep learning on heterogeneous graphs

Applications of deep learning (DL) to design nanomaterials are hampered by a lack of suitable data representations and training data. Here, in this study, we report efforts to overcome these limitations and leverage DL to optimize the nonlinear optical properties of core–shell upconverting nanoparticles (UCNPs). UCNPs, which have applications in fields such as biosensing, super-resolution microscopy and three-dimensional printing, can emit visible and ultraviolet light from near-infrared excitations. We report a large-scale dataset of UCNP emission spectra based on accurate but expensive kinetic Monte Carlo simulations (N > 6,000) and use these data to train a heterogeneous graph neural network using a physically motivated representation of UCNP nanostructure. Applying gradient-based optimization on the trained graph neural network, we identify structures with 6.5× higher predicted emission under 800-nm illumination than any UCNP in our training set. Our work reveals design principles for UCNP heterostructures and presents a roadmap for DL-based inverse design of nanomaterials.

Sivonxay, Eric [Lawrence Berkeley National Laborat↗
DOE OSTI2025

Corrosion of 316 L stainless steel under the natural circulation of molten NaCl-MgCl 2 salt

The corrosion behavior of 316 L stainless steel (SS) was studied via the natural circulation of molten eutectic NaCl-MgCl 2 salt through a microloop. The post-corrosion tested 316 L SS microloop sections were characterized with microscopy techniques to determine the microstructural and microchemical changes that occurred at the alloy/salt interface. It was found that 316 L SS showed heterogeneous dissolution at the hot-leg, whereas deposition of corrosion products occurred at the cold-leg. For the first time, experimentally obtained molten salt flow-induced corrosion of 316 L SS results were combined with computational thermodynamic-kinetic models to validate the dissolution and deposition in terms of elemental compositional changes at the alloy/salt interface. The thermodynamic-kinetic modeling predicted that the heterogeneous dissolution of Cr and Fe from the hot-leg section of 316 L SS persisted throughout the salt circulation. The model also estimated that, despite Cr deposition starting earlier than Fe, the total redeposition of Fe is expected to be significantly greater than that of Cr over the circulation of salt. Furthermore, the modeling accurately predicted the subsurface enrichment of Mo which is attributed to the reduced Cr activity and the relatively higher diffusion rate of Mo within the alloy matrix. Here, the agreement between modeling and experimental results confirms that Fe chlorides dissolve at the hot-leg and subsequently deposit at the cold-leg due to activity changes driven by the thermal gradient. By contrast, Cr was not detected in the cold-leg deposits, which is attributed to its weaker temperature dependence on activity, limiting its redeposition under these conditions.

36 - MATERIALS SCIENCE↗
DOE OSTI2026

Improved energies and local energies with weighted variational Monte Carlo

Neural network parametrizations have increasingly been used to represent the ground and excited states in variational Monte Carlo (VMC) with promising results. However, traditional VMC methods only optimize the wave function in regions of peak probability. The wave function is uncontrolled in the tails of the probability distribution, which can limit the accuracy of the trained wave function. To improve the approximation accuracy in the probability tails, this paper interprets VMC as a gradient flow in the space of wave functions, followed by a projection step. From this perspective, arbitrary probability distributions can be used in the projection step, allowing the user to prioritize accuracy in different regions of state space. Motivated by this theoretical perspective, the paper tests a weighted VMC method on the antiferromagnetic Heisenberg model for a periodic spin chain. Compared to traditional VMC, weighted VMC reduces the error in the ground state energy by a factor of 2, and it reduces the errors in the local energies away from the mode by large factors of 10 2 –10 4 .

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Coherent structures in stably stratified wall-bounded turbulent flows

To date, a growing body of literature has documented the existence and impacts of coherent structures known as large- and very-large-scale motions within wall-bounded turbulent flows under neutral and unstable thermal stratification. These coherent structures can account for a considerable fraction of the overall turbulent transport and have been found to modulate small-scale turbulent fluctuations near the wall. In the context of stably stratified flows, however, the examination of such coherent structures has garnered relatively little attention. Stable stratification limits vertical transport and turbulent mixing within flows, which makes it unclear the extent to which previous findings on coherent structures under unstable and neutral stratification are applicable to stably stratified flows. In this study, we investigate the existence and characteristics of coherent structures under stable stratification with a wide range of statistical and spectral analyses. Outer peaks in premultiplied spectrograms under weak stability indicate the presence of large-scale motions, but these peaks become weaker and eventually vanish with increasing stability. Quadrant analysis of turbulent transport efficiencies (the ratio of net fluxes to their respective downgradient components) demonstrates dependencies on both stability and height above ground, which is evidence of morphological differences in the coherent structures under increasing stability. Amplitude modulation by large-scale streamwise velocity was found to decrease with increasing gradient Richardson number, whereas modulation by large-scale vertical velocity was approximately zero across all stability ranges. For sufficiently stable stratification, large eddies are suppressed enough to limit any inner–outer scale interactions.

Greene, Brian R. (ORCID:0000000343766818)↗
DOE OSTI2024

Speeding up and reducing memory usage for scientific machine learning via mixed precision

Scientific machine learning (SciML) has emerged as a versatile approach to address complex computational science and engineering problems. Within this field, physics-informed neural networks (PINNs) and deep operator networks (DeepONets) stand out as the leading techniques for solving partial differential equations by incorporating both physical equations and experimental data. However, training PINNs and DeepONets require significant computational resources, including long computational times and large amounts of memory. In search of computational efficiency, training neural networks using half precision (float16) rather than the conventional single (float32) or double (float64) precision has gained substantial interest, given the inherent benefits of reduced computational time and memory consumed. However, we find that float16 cannot be applied to SciML methods, because of gradient divergence at the start of training, weight updates going to zero, and the inability to converge to a local minima. To overcome these limitations, we explore mixed precision, which is an approach that combines the float16 and float32 numerical formats to reduce memory usage and increase computational speed. Our experiments showcase that mixed precision training not only substantially decreases training times and memory demands but also maintains model accuracy. Here, we also reinforce our empirical observations with a theoretical analysis. The research has broad implications for SciML in various computational applications.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Chiral kinematic theory and converse vortical effects

Response theories in condensed matter typically describe the response of an electron fluid to external electromagnetic fields, while perturbations on neutral particles are often designed to mimic such fields. Here, we study the response of fermions to a space-time-dependent velocity field, thereby sidestepping the issue of gauge charge. First, we use a semiclassical chiral kinematic theory to obtain the local density of current and extract the orbital magnetization. The theory immediately predicts a "converse vortical effect," defined as an orbital magnetization driven by linear velocity. It receives contributions from magnetic moments on the Fermi surface and the Berry curvature of the occupied bands. Then, transcending semiclassics via a complementary Kubo formalism reveals that the uniform limit of a clean system receives only the Berry curvature contribution while other limits sense the Fermi surface magnetic moments too. We propose CoSi as a candidate material and suggest magnetometry of a sample under a thermal gradient to detect the effect. Overall, our study sheds light on the effects of a space-time-dependent velocity field on electron fluids and paves the way for exploring quantum materials using new probes and perturbations.

Chen, Kai↗
DOE OSTI2024

Aridity and forest age mediate landscape scale patterns of tropical forest resistance to cyclonic storms

Abstract Cyclonic storms, or hurricanes, are expected to intensify as ocean heat energy rises due to climate change. Ecological theory suggests that tropical forest resistance to hurricanes should increase with forest age and wood density. However, most data on hurricane effects on tropical forests come from a limited number of well‐studied long‐term monitoring sites, restricting our capacity to evaluate the resistance of tropical forests to hurricanes across broad environmental gradients. In this study, we assessed whether forest age and aridity mediate the effects of hurricanes Irma and Maria in Puerto Rico, Vieques and Culebra islands. We leveraged functional trait data for 410 tree species, remotely sensed measurements of canopy height and cover, along with data on forest stand characteristics of 180 of 338 forest monitoring plots, each covering an area of 0.067 ha. The plots represent a broad mean annual precipitation (MAP) gradient from 701 to 4598 mm and a complex mosaic of forest age from 5 to around 85 years since deforestation. Hurricanes resulted in a 25% increase in basal area mortality rates, a 45% decrease in canopy height and a 21% reduction in canopy cover. These effects intensified with forest age, even after considering proximity to the hurricane path. The links between forest age and hurricane disturbances were likely due the prevalence of tall canopies. Tall forest canopies were strongly linked with low community‐weighted wood density (WD). These characteristics were on average more common in moist and wet forests (MAP >1250 mm). Conversely, dry forests were dominated by short species with high wood density (WD > 0.6 g cm −3 ) and did not show significant increases in basal area mortality rates after the hurricanes. Synthesis . Our findings show that selection towards drought‐tolerant traits across aridity gradients, such as short stature and dense wood, enhances resistance to hurricanes. However, forest age modulated responses to hurricanes, with older forests being less resistant across the islands. This evidence highlights the importance of considering the intricate links between ecological succession and plant function when forecasting tropical forests’ responses to increasingly strong hurricanes.

Vargas G., German↗