Search NASA⌕ Search

SEARCH · Search NASA

Results for “HULLS - IMPACT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Refurbishment of SRB aluminum components by walnut hull blast removal of protective coatings

A test program was conducted to develop, optimize, and scale up an abrasive blasting procedure was developed for refurbishment of specific SRB components: aft skirt, forward skirt, frustrum, and painted piece parts. Test specimens utilizing 2219 T87 aluminum substrate of varying thicknesses were prepared and blasted at progressively increasing pressures with selected abrasives. Specimens were analyzed for material response. The optimum blasting parameters were determined on panel specimens and verified on a large cylindrical integrated test bed.

Colberg, W. R.↗
NASA NTRS1991

A Navier-Stokes Solution of Hull-Ring Wing-Thruster Interaction

Navier-Stokes simulations of high Reynolds number flow around an axisymmetric body supported in a water tunnel were made. The numerical method is based on a finite-differencing high resolution second-order accurate implicit upwind scheme. Four different configurations were investigated, these are: (1) barebody; (2) body with an operating propeller; (3) body with a ring wing; and (4) body with a ring wing and an operating propeller. Pressure and velocity components near the stern region were obtained computationally and are shown to compare favorably with the experimental data. The method correctly predicts the existence and extent of stern flow separation for the barebody and the absence of flow separation for the three other configurations with ring wing and/or propeller.

Yang, C.-I.↗
NASA NTRS1991

Rule groupings in expert systems using nearest neighbour decision rules, and convex hulls

Expert System shells are lacking in many areas of software engineering. Large rule based systems are not semantically comprehensible, difficult to debug, and impossible to modify or validate. Partitioning a set of rules found in CLIPS (C Language Integrated Production System) into groups of rules which reflect the underlying semantic subdomains of the problem, will address adequately the concerns stated above. Techniques are introduced to structure a CLIPS rule base into groups of rules that inherently have common semantic information. The concepts involved are imported from the field of A.I., Pattern Recognition, and Statistical Inference. Techniques focus on the areas of feature selection, classification, and a criteria of how 'good' the classification technique is, based on Bayesian Decision Theory. A variety of distance metrics are discussed for measuring the 'closeness' of CLIPS rules and various Nearest Neighbor classification algorithms are described based on the above metric.

Anastasiadis, Stergios↗
NASA NTRS1924

Static stability of seaplane floats and hulls

Values of lateral and longitudinal metacentric heights for various seaplanes were calculated by means of approximate formulae derived here. The data are given in tabular form. Upon plotting these metacentric heights against the corresponding gross weights, it appears that the metacentric height is approximately a straight line function of the gross weight. For the lateral metacentric height GM = 13 + .002 W and for longitudinal metacentric height GM = 15 + .002 W, GM is in feet and the gross weight (W) is in pounds. Although only approximate, it is thought that the values indicated here are a reliable guide to current practice. It is recommended that the longitudinal and lateral metacentric heights be made equal and of the value given by GM = 15 = .002 W. The proper length or spacing required to satisfy the indicated value may then be obtained from substitution in the approximate formulae for metacentric height.

Diehl, W S↗
NASA NTRS1933

A Complete Tank Test of a Model of a Flying-boat Hull - N.A.C.A. Model No.11-A

Model No. 11-A was designed as an improvement over N.A.C.A. Model No. 11, a complete test of which is described in N.A.C.A. Technical Note No. 464. In contrast with the longitudinal upward curvature in the planing bottom forward of the main step on Model 11-A was made as flat as practicable. Otherwise, the two models have very nearly the same form. The results of towing tests made on Model 11-A in the N.A.C.A. tank over a wide range of speed, load on the water, and trim angle are presented, both as original test data and as non dimensional coefficients. A comparison is made with similar results from the test of Model No. 11. The practical significance of the improvement obtained is demonstrated by applying the data from the new form to the illustrative design problem use in the note on Model NO. 11.

Parkinson, John B↗
NASA NTRS1935

The effect of depth of step on the water performance of a flying-boat hull model

NACA model 11-C was tested with four different depths of step to obtain information as to the effect of the depth of step on the water performance. The depths of step were selected to cover the practicable range of depths and in each case the included angle between the forebody and afterbody keels was kept the same 6-1/2 degrees. Small depths of step were found to give lower resistance at speeds below and at the hump speed of the model and greater depths of step lower resistance at high speeds. For low resistance throughout the speed range of the model investigated the most desirable depth of step is from 2.5 to 4.0 percent of the beam. The change of the best trim angle caused by variation of the depth of step was not appreciable. Increased depth of step caused increases in the maximum positive trimming moments at all trim angles investigated.

Bell, Joe W↗
NASA NTRS1935

Tank Tests of a Model of a Flying-boat Hull Having a Longitudinally Concave Planing Bottom

The NACA model 11-B, which has a longitudinally concave planing bottom forward of the step, was tested over a wide range of loading. The results of the tests are presented as curves of resistance and trimming moment plotted against speed for various trim angles and as curves of resistance coefficient at best trim angle, and trimming-moment coefficient. The characteristics of the form at the optimum trim are compared with those of NACA model 11-C which has the same form with the exception of a planing bottom longitudinally straight near the step. Photographs of the models being towed in the tank are included for a comparison of the spray patterns. At the best angles of trim in each case model 11-B has lower resistance at high speeds, a higher maximum positive trimming moment near the hump speed, and a more favorable spray pattern than of model 11-C.

Parkinson, J B↗
NASA NTRS1933

A complete tank test of a model of a flying-boat hull-N.A.C.A. Model No.11

This note discusses the limitations of the conventional tank test of a seaplane model. The advantages of a complete test, giving the characteristics of the model at all speeds, loads, and trim angles in the useful range are pointed out. The data on N.A.C.A. Model No.11, obtained from a complete test, are presented and discussed. The results are analyzed to determine the best trim angle for each speed and load. The data for the best angles are reduced to non-dimensional form for ease of comparison and application. A practical problem using the characteristics of model no.11 is presented to show the method of calculating the take-off time and run of a seaplane from these data.

Shoemaker, James M↗