Search NASA⌕ Search

SEARCH · Search NASA

Results for “High temperature applications”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Degradation of Magnetic Materials for High-Temperature Active Magnetic Bearing Applications in CO₂-Based Environments

High-temperature Active Magnetic Bearings (AMBs) are a promising alternative to conventional bearings in hermetically sealed turbomachinery for supercritical CO₂ (sCO₂) systems. They offer reduced CO₂ leakage, lower windage losses, enhanced misalignment tolerance, reduced wear, and built-in diagnostic capabilities. A critical challenge, however, is ensuring long-term material stability in harsh CO₂-rich environments. This study investigated the degradation behavior of permanent and soft magnetic materials (Alnico 9C, Alnico 5-7C, SmCo 18-T550, Hiperco-50, and coated variants) after up to 6,000 hours of exposure in gaseous CO₂, sCO₂, or air at 450 °C and 550 °C. The evaluation included post-exposure mass change measurements, scanning electron microscopy (SEM) analysis, and magnetic property assessments. The results demonstrate oxidation rates, microstructural evolution, and retention of magnetic performance across conditions. The findings offer essential insights into the thermal corrosion behavior of magnetic materials under CO₂ rich environments and serve as a reference for material selection in AMB system designs.

36 MATERIALS SCIENCE↗
DOE OSTI2024

High temperature stability of regrown and alloyed Ohmic contacts to AlGaN/GaN heterostructure up to 500 °C

This Letter reports the stability of regrown and alloyed Ohmic contacts to AlGaN/GaN-on-Si high electron mobility transistors (HEMTs) for high temperature applications up to 500 °C. Transfer length method (TLM) measurements from 25 to 500 °C in air show that the regrown contacts appear to be stable up to 500 °C during short term (approximately 1 h) testing, while alloyed contacts appear to decrease in contact resistance from 300 to 500 °C though increases in the error bounds due to increase sheet resistance make it difficult to conclude definitely. Additionally, longer term testing shows both technologies remain stable at least up to 48 h at 500 °C, after which the large increase in sheet resistance makes the measurement uncertainty too large to conclude definitively. Advanced microscopy images indicate both the regrown and alloyed contact regions remain structurally intact after prolonged high temperature exposure with no visible degradation in crystallinity or metal composition.

Physics↗
DOE OSTI2023

Oxidation performance and limitations of additively manufactured SiC/Si-O-C composites at elevated temperatures

Here, SiC preforms were infiltrated with polycarbosiloxane preceramic polymer to create low-cost SiC—Si x O y C z matrix composites for possible high temperature application. The effect of specimen annealing conditions on the steam and air oxidation resistance was analyzed. Air exposures from 900–1500°C showed stability of the Si x O y C z matrix phase with moderate oxidation resistance. After 900°C exposures, oxidation of the composite is primarily limited to the matrix phase, and only at 1200 and 1500°C was SiC consumption visualized. Steam cycle exposures at 1200°C resulted in rapid linear oxidation of the composites with induced specimen swelling from volume expansion associated with internal oxidation. Specimens annealed in argon were found to be the most oxidation resistant due to increased matrix crystallinity and carbon retention. The results of this work were used to develop clear strategies for improving the high-temperature properties of SiC—Si x O y C z composites.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thermal Barrier Coatings Overview: Design, Manufacturing, and Applications in High-Temperature Industries

Today’s competitive world economy is creating an indispensable demand for increased efficiency of engineering components that operate in harsh environments (i.e., very high-temperature, corrosive, or neutron irradiation environments), for applications in the energy, automotive, aerospace, electronics, and power industries. Increased research is being done on thermal barrier coatings (TBCs) for protecting such components, since the versatility of manufacturing techniques and the scale of deployment result in increased life, economics, performance, and durability. This review focuses on the advances that led to using TBCs for component life extension and, more recently, as an integral part of advanced component design for high-temperature and other types of harsh environments, such as those found in nuclear-related applications. Furthermore, factors that led to state-of-the-art advanced coating-fabrication techniques [e.g., electron-beam physical vapor deposition (EB-PVD), plasma spray deposition, and electrophoretically deposited TBCs, as well as functionally graded material (FGM) manufacturing] have also been emphasized in current coating R&D. This review explores the current state of TBCs, i.e., the latest advances regarding their fabrication and performance, associated challenges, and recommendations for their future use in aerospace, nuclear, high-temperature, or otherwise harsh environments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

High Pressure and Two-Sided Mold Surface Solutions (CRADA Final Report)

This project provided surface solutions for highly loaded precision tooling relevant to the automotive industry. Previous development work in coatings for Big Area Additive Manufacturing (BAAM) has produced commercialized coatings for low temperature Acrylonitrile Butadiene Styrene (ABS) tools (TD Coat RT) as well as a soft coating for high temperature applications (TD Seal HT). The team developed these coatings and commercialized them during a prior Manufacturing Demonstration Facility (MDF) technical collaboration (NFE-15-05793). During the prior collaboration, commercialization testing was successfully performed by the Boeing and NAVAIR and resulted in an Awards for Composites Excellence (ACE), award at CAMX – The Composites and Advanced Materials Expo 2016. While this work was clearly successful, gaps in the technology were identified, that prevent widespread adoption of large-scale additive manufacturing in high pressure tooling applications prevalent in the automotive industry. In this project we focused on development of surface solutions for two-sided, compression molding tooling printed on a large-scale polymer AM system in an arbitrary build orientation. We have printed a single cavity extrusion compression molding mold using Polyphenylene sulfide/carbon fiber (PPS/CF) materials, 50% by weight CF samples. These processes are commonly used by Original Equipment Manufacturers (OEM) and Tier 1 suppliers for high volume automotive applications. Several OEMs have identified the need for such technology, indicating significant time and monetary savings could be possible if commercially available surface solutions for high pressure Additive Manufacturing (AM) tooling existed.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Additively manufactured refractory high-entropy alloys with superior radiation resistance

Refractory high-entropy alloys (RHEAs) are promising candidates for next-generation nuclear and high-temperature applications. Among many approaches to manufacture RHEAs, additive manufacturing (AM) represents the most recent and advanced metal manufacturing method which allows near-net-shape manufacturing to reduce material waste and post-processing time. However, performance of AM RHEAs under complex irradiation conditions remains largely unexplored. Here, in this study, we demonstrate for the first time the response of directed energy deposition (DED) AM quaternary RHEAs (HfTaVW, CrTaVW) subjected to sequential dual-beam ion irradiation, consisting of helium pre-implantation followed by high-dose heavy ion bombardment. Compositions of DED AM RHEAs were selected using Monte Carlo (MC) simulations based on a cluster expansion (CE) Hamiltonian parameterized by density functional theory (DFT). Post-irradiation microstructural characterization revealed that the AM RHEA maintained remarkable stability, with suppressed helium bubble growth and reduced defect accumulation compared to conventional alloys. Even at high doses (∼100 dpa), the alloy exhibited no void swelling, a low density of dislocation loops, and no evidence of severe degradation. These results highlight the intrinsic ability of AM-derived microstructures and multicomponent chemistry to synergistically mitigate irradiation effects. Our findings establish AM RHEAs as a class of materials with superior resistance to radiation damage under conditions relevant to advanced fusion and fission environments and demonstrate the importance of sequential ion beam studies in evaluating their long-term performance.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Computationally-Guided ODS Refractory HEAs via Additive Manufacturing

This document is the final report for ARPA-E ULTIMATE project DE-AR0001422. To achieve higher efficiency turbine operation, the RTX Technology Research Center (RTRC) explored the use of additive manufacturing (AM) to produce test specimens of novel high entropy alloys (HEA) enhanced with oxide dispersion strengthening (ODS). HEAs, with multiple principal elements, offer a vast alloy design space rich with unique properties especially enhanced solid solution strengthening. ODS alloys historically are some of the best performing materials for high temperature applications. Leveraging AM enables near net shape part production and incorporation of ODS into the alloy. Density, melting temperature, and elevated temperature strength properties of several novel HEA compositions were found to meet or exceed program targets; however, obtaining sufficient room temperature ductility in these alloys proved challenging. In order to obtain an alloy with sufficient ductility, the team explored more conventional refractory alloy compositions, focusing on a niobium based alloy. This inherently ductile alloy also satisfied program metrics for cost, density, and fracture toughness. Results showed the oxide dispersions increased high temperature strength, and improved creep resistance compared to the conventional alloy, though the program creep metric was not met. Further tuning of the alloy chemistry, and optimization of the oxide dispersion, is likely required to improve creep resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Selective laser melting of 304L stainless steel: Role of volumetric energy density on the microstructure, texture and mechanical properties

The role of volumetric energy density on the microstructural evolution, texture and mechanical properties of 304L stainless steel parts additively manufactured via selective laser melting process is investigated. 304L is chosen because it is a potential candidate to be used as a matrix in a metal matrix composite with nanoparticles dispersion for energy and high temperature applications. The highest relative density of 99 %±0.5 was achieved using a volumetric energy density of 1400 J/mm 3 . Both XRD analysis and Scheil simulation revealed the presence of a small trace of the delta ferrite phase, due to rapid solidification within the austenitic matrix of 304L. Here, a fine cellular substructure ranged between 0.4–1.8 μm, was detected across different energy density values. At the highest energy density value, a strong texture in the direction of [100] was identified. At lower energy density values, multicomponent texture was found due to high nucleation rate and the existing defects. Yield strength, ultimate tensile strength, and microhardness of samples with a relative density of 99 % were measured to be 540 ± 15 MPa, 660 ± 20 MPa and 254 ± 7 HV, respectively and higher than mechanical properties of conventionally manufactured 304L stainless steel. Heat treatment of the laser melted 304L at 1200 °C for 2 h, resulted in the nucleation of recrystallized equiaxed grains followed by a decrease in microhardness value from 233 ± 3 HV to 208 ± 8 HV due to disappearance of cellular substructure.

304L stainless steel↗
DOE OSTI2025

Critical Component/Technology Gap in 21 st Century Power Plant Gasification Based Polygeneration: Advanced Ceramic Membranes/Modules for Ultra Efficient Hydrogen (H 2 ) Production/Carbon Dioxide (CO 2 ) Capture for Coal-Based Polygeneration

The 21 st Century Power Plant Gasification Based Polygeneration power plant layout is a relatively straightforward retrofit of well-established ammonia synthesis technology to the baseline IGCC process and envisions co-production of power and chemicals from coal in the context of carbon capture. A Dual Stage Membrane Process (DSMP) for pre-combustion CO 2 capture in a coal fired IGCC power plant has been demonstrated by Media and Process Technology Inc (MPT) (DE-FE0013064) in bench-scale live gas testing at the NCCC. This work, however, highlighted the importance of permeate purge capability to deliver deep H 2 recovery at moderate pressures and high carbon capture performance. Further, in the area of warm gas processing, a permeate purgeable membrane support for a wide range of inorganic high-performance membrane materials (CMS, Pd-alloy, zeolite, ZIF, graphene, etc.) was not available and hence had been a common and significant barrier to their commercialization. Hence, the Critical Technology Gap to implementing the DSMP in the Polygeneration power plant and more broadly in advanced warm gas separation applications was the inability to permeate purge the membranes coupled with the lack of the availability of a high packing density scalable package design. To overcome this Critical Technology Gap, in this project, the primary objective was the development of a permeate purgeable full ceramic support for these high-performance inorganic membranes and the complementary high packing density housing. Our goal and approach were to extend our “candle filter” design to a “dual end open” package to enable permeate purge and scalability. Microporous ceramic membranes have been proven to be a low cost, stable material for high temperature applications under harsh environment. They are the leading support choice of researchers in advanced inorganic membrane development in applications such as pre-combustion CO 2 capture. The new 2nd Generation “dual end open” bundle developed in this project is a universal support for these existing and emerging inorganic membrane technologies that up to now have lacked a pathway out of the laboratory. The full ceramic permeate purgeable support represents a transformational technology and opens the door to commercialization of these advanced membrane materials in a wide array of mega scale commercial applications in gas (and liquid) processing under aggressive conditions not suited to conventional polymeric membranes.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Tailoring critical Al concentration to form external Al 2 O 3 scale on Ni–Al alloys by computational approach

Abstract Nickel (Ni)‐based superalloys for high‐temperature applications are often designed to form a continuous and slow‐growing oxide scale by adding Al and Cr and other beneficial elements. In the present work, the critical Al concentration in Ni–Al alloys needed to establish an α‐Al 2 O 3 scale in contrast to internal oxide formation is predicted as a function of temperature by means of the CALPHAD approach coupled with models in the literature, which account for the thermodynamics and kinetics of oxidation. The present thermodynamic remodeling of the Ni–O system results in a better agreement with experimental data of oxygen solubility in Ni at high temperatures. The oxygen solubility is combined with kinetic parameters to determine oxygen permeability in Ni, and the critical Al concentration needed to establish an α‐Al 2 O 3 scale at a given exposure temperature. Good agreement is found with available experimental data for both oxygen permeability and critical Al concentration, indicating the capacity of the CALPHAD approach to tailor oxidation resistance for materials of interest using thermodynamic and kinetic knowledge.

Ross, Austin↗
DOE OSTI2020

Void formation during cyclic oxidation of oxide dispersion strengthened FeCrAl alloys

Here, oxide dispersion strengthened FeCrAl alloys are considered for various high-temperature applications due to their excellent mechanical properties and oxidation resistance, but void formation is a concern for component durability. Cyclic oxidation testing was conducted on alloy MA956 and PM2000 at 1100–1200ºC for durations of up to 10,000 h and the void content was determined from optical cross-sections by image analysis. At 1100ºC, 100 h cycle, the low void concentrations measured were consistent with two competing mechanisms proposed in the literature: coalescence of process-induced nano-voids and alloy sintering. At 1200ºC using 1 h cycles, the void concentration was much higher, reaching ~3% to 6% for specimens tested to breakaway oxidation. The void growth was attributed to the high oxidation rates and the annihilation of oxidation-induced vacancies at the surface of the process-induced voids.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Alloy designs for high temperature Mo-base systems

For high temperature applications Mo base alloy requirements include both superior structural performance and environmental resistance. To address these requirements alloys in the Mo-Si-B system and refractory multi-principal element alloys (RMPEA) are being developed that exhibit a promising potential, but also have some remaining challenges to improve ductility, lower density and enhance environmental resistance. In the Mo-Si-B system microstructures with a Mo solid solution (Moss) Mo 3 Si and Mo 5 SiB 2 (T2) phases have been the focus of attention. However, the Si solubility in the Moss phase diminishes the ductility and toughness. In order to address this issue a new design based upon Moss, Mo 2 B and T 2 phases lowers the Si solubility in the Moss to improve ductility while the T 2 phase maintains the oxidation performance. Selected additions of Al and Ti enable a density reduction to below 8 g/cm 3 . The RMPEA designs for Mo-rich alloys provide for excellent structural performance, but the complex oxidation products provide no protection. However, in this case a new coating design has been introduced that provides the required environmental resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Overcoming sparse datasets with multi-task learning as applied to high entropy alloys

Abstract The design of novel High Entropy Alloys for use in high-temperature applications is an area of active interest due to their potential to provide exceptional properties compared to conventional alloys. Since the increased popularity of machine learning, an important cog in the design process has been training surrogate models on alloy properties. However, these Single-Task models are trained on individual mechanical properties and do not take advantage of the relatedness between properties. Multi-Task models can capture the interdependencies between tasks, leading to potentially more accurate predictions for all tasks. In this paper, we investigate if Multi-Task models can show improvement over Single-Task models when used for predicting the mechanical properties of these alloys. To ensure fair evaluation between the models, we apply L 0 regularization and skip connections to the models, which allows them to adjust the number of model parameters and depth for optimal performance. We find that the Multi-Task models can leverage task relationships to perform better than Single-Task models, especially for high amounts of missing data in the tasks. Furthermore, adding simple auxiliary targets can boost Multi-Task performance even further despite not being effective as input descriptors to single-task models themselves. We anticipate that the proposed strategies can achieve more accurate predictions and consequently enable better design capabilities for such data-constrained domains without incurring much additional computational cost.

Debnath, Arindam (ORCID:0000000194274499)↗
DOE OSTI2023

Surface oxygen exchange kinetics of mixed conducting oxides: Dilatometric vs electrical conductivity relaxation study

The surface oxygen exchange kinetics of mixed ionic-electronic conducting (MIEC) oxides play a crucial role in a variety of applications, including solid oxide fuel/electrolysis cells (SOFCs/SOECs), permeation membranes and sensors. To date, a variety of methods, including isotope exchange, electrical conductivity, optical absorptivity and thermogravimetry relaxation, and impedance spectroscopy have been used to measure the oxygen exchange coefficient of MIEC oxides. Each of these methods have their advantages and limitations, depending on the physical and chemical properties of the investigated materials and their sample dimensions and densities. Here, we demonstrate the ability to precisely measure the surface oxygen exchange coefficient (k chem ) of MIEC model material Pr 0.1 Ce 0.9 O 2-δ (PCO) by use of dilatometric relaxation measurements, particularly of interest for materials that exhibit larger chemical expansion coefficients. This is achieved by use of porous bulk specimens to ensure that the contribution of oxygen exchange to the overall kinetics is dominant. We demonstrate that k chem values extracted from chemical expansion relaxation measurements on PCO are nearly identical to those derived from electrical conductivity relaxation measurements. As a result, this provides the opportunity to precisely investigate the oxygen exchange and chemical expansion kinetics of a wide range of materials used in high-temperature applications, particularly where more conventional methods are difficult or inappropriate to apply.

(Pr,Ce)O2-x↗
DOE OSTI2020

The synergistic role of Mn and Zr/Ti in producing θ'/L12 co-precipitates in Al-Cu alloys

Microstructural stability is a critical factor to consider when designing new alloys for high-temperature applications. An Al-Cu alloy with Mn and Zr additions has recently been developed to withstand extended exposures of up to 350 °C. The addition of Mn in combination with Zr and their segregation to precipitate interfaces play a significant role in stabilizing the metastable θ ' precipitates responsible for the alloy's hardness; however, adding Zr and Mn separately only improves the stability to 200 °C and 300 °C, respectively. To this end, the effect of the synergistic additions on interfacial structure and chemistry was studied in detail using atom probe tomography (APT) and scanning transmission electron microscopy (STEM) for Al-Cu-Mn-Zr/Ti-containing alloys subjected to long-term annealing (up to 2,100 h) in the critical temperature range, 300 °C and 350 °C, to investigate the role of Zr/Ti in increasing the θ '-precipitate stability. The APT and STEM results reveal that Mn additions stabilize θ ' long enough for the slower diffusing Zr atoms to segregate to coherent θ ' interfaces that eventually create a θ '/ L1 2 -Al 3 (Zr x ,Ti 1-x ) co-precipitate structure. The co-precipitate is highly stable, as shown by density functional theory calculations, and is a key factor that governs microstructural stability beyond 300 °C. This study reveals how solute additions with different stabilization mechanisms can work in concert to stabilize a desired microstructure, and the results provide insights that can be applied to other high-temperature alloy systems.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Improved creep performance of CoCrFeNi high entropy alloys by Mo addition

The CoCrFeNi family of high entropy alloys has good mechanical and corrosion properties, performing like stainless steels with low yield stresses. They could, however, benefit from hardening methods for structural and high temperature applications. Here, this work investigates the potential for the CoCrFeNi alloy to be hardened with the addition of Mo. A series of CoCrFeNiMo alloys and their CoCrFeNi counterparts were subsequently manufactured at NETL and then mechanically creep tested at 650°C. The alloys were designed to possess a range of stacking fault energies which influence the mechanical properties of the alloys via the motion of their dislocations under stress. Results show that Mo-containing variants have creep rupture lives ranging from 4000 to 8000 hours, i.e., about two orders of magnitude longer than those for Mo-free variants. The significantly improved creep performance of the Mo-containing alloys is due to a combination of solid solution strengthening and precipitation strengthening from µ-phase and carbides.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Alloying Effects on the Transport Properties of Refractory High-entropy Alloys

Additive Manufacturing (AM) has opened new frontiers for the design of refractory high-entropy alloys (HEAs) for high-temperature applications. The thermal conductivity of the AM feedstock is among the most important thermo-physical properties that control the melting and solidification process. Despite its significance, there remains a notable gap in both computational and experimental research concerning the thermal conductivity of HEAs. Here, we use density functional theory (DFT) to systematically investigate the alloying effects on the transport properties of Ti-Cr-Mo-W-V-Nb-Ta RHEAs, including electrical and thermal conductivities and Seebeck coefficient. The relaxation time of charge carriers is a key underlying parameter determining thermal conductivity that is exceedingly challenging to predict from first principles alone, and we thus follow the approach by Mukherjee, Satsangi, and Singh [Chem Mater 32, 6507 (2022)] to optimize the relaxation time for RHEAs. Here we validated thermal conductivity predictions on elemental solids, binary and ternary alloys, and RHEAs and compared them against thermodynamic (CALPHAD) predictions and our experiments with good correlations. To understand observed trends in thermal conductivity, we assessed the phase stability, electronic structure, phonon, and intrinsic- and tensile strength of down-selected RHEAs. Our electronic structure and phonon results connect well with the observed compositional trends for thermal transport in RHEAs. Our DFT assessment and CALPHAD predictions provide a unique design guide for RHEAs with tailored thermal conductivity, a critical consideration for AM and thermal-management applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Powder Metallurgy HIP Process Study and Mechanical Property Evaluations for IN740H

The effects of hot isostatic pressing (HIP) parameters and powder size distribution (PSD) on the resulting microstructure and properties of powder metallurgy (P/M) IN740H have been investigated. Properties can be substantially tailored through the appropriate management of these parameters. Applying a thermal presoak to the input powder prior to the sintering stage of HIP can significantly increase average grain size and coarse grain fraction, enabling a trade for improved creep resistance at the expense of tensile strength. Here, powder thermal presoak was found to have a larger impact on microstructure and properties than the use of a coarser PSD alone. Additionally, substantial grain growth and grain boundary migration is observed in P/M IN740H at HIP temperatures above 1260°C. Given its inherently finer grain size, P/M HIP IN740H typically outperforms its cast and wrought counterparts in tensile response. Creep life at 700–800°C was inferior to wrought due to PPBs coincident with grain boundaries which served as cavity nucleation sites, leading to lower creep ductility. The ability to adjust the microstructure toward a more balanced creep and tensile behavior allows P/M HIP IN740H to be considered for high-temperature applications in advanced ultra-supercritical steam and supercritical carbon dioxide power cycles.

36 MATERIALS SCIENCE↗