Search NASA⌕ Search

SEARCH · Search NASA

Results for “Hovering Rotor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Hover performance tests of baseline metal and Advanced Technology Blade (ATB) rotor systems for the XV-15 tilt rotor aircraft

Rotor hover performance data were obtained for two full-scale rotor systems designed for the XV-15 Tilt Rotor Research Aircraft. One rotor employed the rectangular planform metal blades (rotor solidity = 0.089) which were used on the initial flight configuration of the XV-15. The second rotor configuration examined the nonlinear taper, composite-construction, Advanced Technology Blade (ATB), (rotor solidity = 0.10) designed to replace the metal blades on the XV-15. Variations of the baseline ATB tip and cuff shapes were also tested. A new six-component rotor force and moment balance designed to obtain highly accurate data over a broad range of thrust and torque conditions is described. The test data are presented in nondimensional coefficient form for the performance results, and in dimensional form for the steady and alternating loads. Some wake and acoustic data are also shown.

Bartie, K.↗
NASA NTRS1973

Leading edge serrations which reduce the noise of low-speed rotors

Acoustic effects of serrated brass strips attached near the leading edges of two different size rotors were investigated. The two bladed rotors were tested in hover. Rotor rotational speed, blade angle, serration shape, and serration position were varied. The serrations were more effective as noise suppressors at rotor tip speeds less than 135 m/sec (444 ft/sec) than at higher speeds. high frequency noise was reduced but the low frequency rotational noise was little affected. Noise reductions from 4 to 8 db overall sound pressure level and 3 to 17 db in the upper octave bands were achieved on the 1.52 m (5.0 ft) diameter rotor. Noise reductions up to 4 db overall sound pressure level were measured for the 2.59 m (8.5 ft) diameter rotor at some conditions.

Soderman, P. T.↗
NASA NTRS1989

Time domain unsteady incompressible cascade airfoil theory for helicopter rotors in hover

A detailed derivation of a finite-time arbitrary-motion incompressible cascade theory is presented for both Laplace and frequency domains. The generalized cascade lift deficiency function is shown to be consistent with the generalized Theodorsen's lift deficiency function when the wake spacing approaches infinity or when the reduced frequency tends to infinity; it also yields a correct value for the zero reduced frequency limit. Efficient numerical procedures are presented for the evaluation of the cascade lift deficiency function. Numerical examples comparing the cascade lift deficiency function with Loewy's (1957) rotary-wing lift deficiency function in frequency domain are presented. Pade approximants of the cascade lift deficiency function are constructed using a Bode plot approach that allows for complex poles. A general-purpose optimization program is used to determine the coefficients of the approximant.

Dinyavari, M. A. H.↗
NASA NTRS1959

Maximum Mean Lift Coefficient Characteristics at Low Tip Mach Numbers of a Hovering Helicopter Rotor Having an NACA 64(1)A012 Airfoil Section

An investigation has been conducted on the Langley helicopter test tower to determine experimentally the maximum mean lift-coefficient characteristics at low tip Mach number and a limited amount of drag- divergence data at high tip Mach number of a helicopter rotor having an NACA 64(1)AO12 airfoil section and 8 deg of linear washout. Data are presented for blade tip Mach numbers M(t) of 0.29 to 0.74 with corresponding values 6 6 of tip Reynolds number of 2.59 x 10(exp 6) and 6.58 x 10(exp 6). Comparisons are made between the data from the present rotor with results previously obtained from two other rotors: one having NACA 0012 airfoil sections and the other having an NACA 0009 airfoil tip section. At low tip Mach numbers, the maximum mean lift coefficient for the blade having the NACA 64(1)AO12 section was about 0.08 less than that obtained with the blade having the NACA 0009 tip section and 0.21 less than the value obtained with the blade having the NACA 0012 tip section. Blade maximum mean lift coefficient values were not obtained for Mach number values greater than 0.47 because of a blade failure encountered during the tests. The effective mean lift-curve slope required for predicting rotor thrust varied from 5.8 for the tip Mach nuniber range of 0.29 to 0.55 to a value of 6.65 for a tip Mach number of 0.71. The blade pitching-moment coefficients were small and relatively unaffected by changes in thrust coefficient and Mach number. In the instances in which stall was reached, the break in the blade pitching-moment curve was in a stable direction. The efficiency of the rotor decreased with an increase in tip speed. Expressed as figure of merit, at a tip Mach number of 0.29 the maximum value was about 0.74. Similar measurements made on another rotor having an NACA 0012 airfoil and with a rotor having an NACA 0009 tip section, showed a value of 0.75. Synthesized section lift and profile-drag characteristics for the rotor-blade airfoil section are presented as an aid in predicting the high-tip-speed performance of rotors having similar airfoils.

Powell, Robert D., Jr.↗
NASA NTRS1985

Experimental study of main rotor tip geometry and tail rotor interactions in hover. Volume 1. Text and figures

A model scale hover test was conducted in the Sikorsky Aircraft Model rotor hover Facility to identify and quantify the impact of the tail rotor on the demonstrated advantages of advanced geometry tip configurations. The test was conducted using the Basic Model Test Rig and two scaled main rotor systems, one representing a 1/5.727 scale UH-60A BLACK HAWK and the others a 1/4.71 scale S-76. Eight alternate rotor tip configurations were tested, 3 on the BLACK HAWK rotor and 6 on the S-76 rotor. Four of these tips were then selected for testing in close proximity to an operating tail rotor (operating in both tractor and pusher modes) to determine if the performance advantages that could be obtained from the use of advanced geometry tips in a main rotor only environment would still exist in the more complex flow field involving a tail rotor. The test showed that overall the tail rotor effects on the advanced tip configurations tested are not substantially different from the effects on conventional tips.

Balch, D. T.↗
NASA NTRS1989

Prediction and measurement of low-frequency harmonic noise of a hovering model helicopter rotor

Far-field acoustic data for a model helicopter rotor have been gathered in a large open-jet, acoustically treated wind tunnel with the rotor operating in hover and out of ground-effect. The four-bladed Boeing 360 model rotor with advanced airfoils, planform, and tip shape was run over a range of conditions typical of today's modern helicopter main rotor. Near in-plane acoustic measurements were compared with two independent implementations of classical linear theory. Measured steady thrust and torque were used together with a free-wake analysis (to predict the thrust and drag distributions along the rotor radius) as input to this first-principles theoretical approach. Good agreement between theory and experiment was shown for both amplitude and phase for measurements made in those positions that minimized distortion of the radiated acoustic signature at low-frequencies.

Aggarawal, H. R.↗
NASA NTRS2018

Generation of Performance Model for the Aeolian Wind Tunnel (AWT) Rotor at Reduced Pressure

The NASA Jet Propulsion Laboratory (JPL) designed the Mars Helicopter (MH) in collaboration with AeroVironment Inc., NASA Ames Research Center, and NASA Langley Research Center to explore the possibility of a vertical takeoff and landing (VTOL) Unmanned Aerial Vehicle (UAV) for flight on Mars. A 40-inch-diameter Aeolian Wind Tunnel (AWT) rotor, roughly approximating the proposed MH design by JPL, was tested in forward flight at Mars atmospheric pressure at the NASA Ames Planetary Aeolian Laboratory (PAL) in support of MH research efforts. This report describes the generation of the rotor model used to correlate with that experimental effort as reported by Ament and Koning. The 40-inch-diameter rotor was 3D-scanned and transformed into an airfoil deck. The scanned rotor airfoil sections are analyzed using C81 Generator (C81Gen) to generate the sectional aerodynamic coefficients for comprehensive analyses. A mid-fidelity computational fluid dynamics (CFD) simulation using Rotorcraft CFD (RotCFD) is pursued to efficiently estimate rotor hover and forward flight performance. Simulations at two pressures, 7 mbar (approximate Martian atmospheric pressure) and 1018 mbar (1 atmosphere), are performed to gain an understanding of the performance differences and Reynolds number effects observed. Experimental 1-atmosphere thrust for single- and dual-rotor isolated hover cases correlate well with the modeled rotor. Performance results at reduced pressure (7 mbar) show a drastic decrease in lift for equivalent RPMs tested at 1 atmosphere. Although this is primarily due to pressure reduction, Reynolds number effects also contribute to this decrease, as airfoil lift and drag coefficients are affected when compared with 1-atmosphere results. Further, simulated rotor power coefficient shows drastic increases at reduced pressures, attributed to laminar boundary layer separation, as described in Koning et al. for the MH rotor analysis. PAL experimental Martian Surface Wind Tunnel (MARSWIT) results are presented in the paper by Ament and Koning. The very low Reynolds number range is currently not well understood and presents various challenges for both experimentation and simulation.

Koning, Witold J. F.↗
NASA NTRS1984

Hovering model helicopter rotor testing

A relatively large test chamber, chosen to minimize room interference effects during helicopter hovering rotor tests, was found in initial operations to exhibit large, random variations of thrust, torque, and blade flapping. The source of these problems, unsteady recirculation of test chamber flow, was addressed by the addition of a 'flow straightener' that reduced these parameter variations to 1.5 percent of mean values. Rotor performance was then measured outside the chamber in calm, free air conditions and compared with chamber results obtained before and after modifications. Attention is given to wake flow visualization conducted in the test chamber, as well as outside.

Piziali, R. A.↗
NASA NTRS2018

Using Pressure Sensitive Paint to Measure Aerodynamic Forces on a Rotor Blade in Hover

This report will present details of a Pressure Sensitive Paint (PSP) system for measuring global surface pressures on rotorcraft blades in hover at the Rotor Test Cell located in the 14- by 22-Foot Subsonic Tunnel complex at the NASA Langley Research Center. This work builds upon previous entries and focused on collecting measurements from the upper and lower surface simultaneously. From these results, normal force (F (sub z)) values can be obtained. To date, this is the first time that the Pressure Sensitive Paint technique has been used for these types of measurements on rotor blades. In addition, several areas of improvement have been identified and are currently being developed for future testing.

Watkins, Anthony Neal↗
NASA NTRSDate not supplied

Overview and Introduction of the Rotor Optimization for the Advancement of Mars eXploration (ROAMX) Project

Research in pursuit of rotorcraft flight on Mars has been ongoing since the late 1990s at NASA Ames Research Center. Since then, many other organizations have also begun researching rotary-wing flight on Mars. In 2014, the project that led to the first helicopter to fly on Mars began at the Jet Propulsion Laboratory. Ingenuity was developed as a joint effort between JPL, NASA Ames, NASA Langley, and AeroVironment. The Ingenuity Mars Helicopter made history in April 2021 as the first vehicle demonstrating controlled, powered flight on another planet and, in doing so, it has opened a new era of planetary aviation. Future, more capable Mars rotorcraft will be able to fly even further and carry significant science payload. At NASA Ames, through NASA Space Technology Mission Directorate funding, the research necessary to help develop the next generation of Mars rotorcraft has begun with the Rotor Optimization for the Advancement of Mars eXploration (ROAMX) project. The ROAMX project involves computationally and experimentally investigating aerodynamically efficient, compressible, low-Reynolds number airfoils for rotor blades and, further, new high-performance rotor designs. ROAMX is also developing and validating a rotor design methodology to optimize blades given specific mission requirements. The primary experimental effort of the ROAMX project is focused on rotor hover performance, but subsequent airfoil and rotor design advances are anticipated to carry over into improvements in forward flight efficiency. ROAMX is a collaboration between NASA Ames, JPL, the University of Maryland, AeroVironment, and Tohoku University.

Rotor Optimization for the Advancement of Mars eXp↗