SEARCH · Search NASA

Results for “IGNITION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS1983

Ignition of confined gaseous mixtures by hot surfaces and hot wires

Ignition times and spatial and temporal variations of temperature and concentration in gaseous mixtures confined between two infinite parallel walls or two infinite cylinders have been obtained by numerical integration of the appropriate conservation equations written in Lagrangian coordinates. Ignition times and ignition energies are presented for the case of an isothermal wall in terms of the initial mixture pressure and equivalence ratio for both one and two-step chemical reaction mechanisms. The numerical results indicate that there is a critical mixture pressure for which the ignition time is minimum. The values of this critical pressure are larger (smaller) than 1 atm for the one- (two-) step reaction mechanism. The critical pressure for the ignition time is not equal to the critical pressure for the ignition energy. The ignition time and energy decrease with the equivalence ratio within a certain range and then remain constant.

Ramos, J. I.↗

NASA NTRS1987

Ignition overpressure study from solid rocket motor firings

The objective was to investigate, through experimental means, the basic mechanisms influencing ignition overpressure and to determine ways to suppress ignition overpressure. Ignition overpressure was studied using solid rocket motors with geometry scaled at 1 percent of the Shuttle's Solid Rocket Boosters. Both water injection and aerosol foam were examined as a mean of reducing ignition overpressure. The results of the water injection tests indicate that a relatively small amount of water is sufficient to provide significant suppression. Of the flow rates tested, the lower water injection flow rates provided the best reduction of the ignition overpressure wave. Also, the test results show there is an optimum water flow rate range that provides the best suppression, and as this range is exceeded the effectiveness of water to reduce ignition overpressure is decreased. Aerosol foam provided very little reduction of ignition overpressure, but only small volumes of foam were used and further testing is necessary to determine its total effectiveness as a means of suppression.

Counter, Douglas D.↗

NASA NTRS1986

Ignition of metals and alloys by high-velocity particles

The ignition of metals and alloys by impacting high-velocity particles in gaseous oxygen was investigated. A convergent/divergent nozzle was used to accelerate the flowing oxygen, which in turn accelerated the particles to velocities greater than 305 m/s (1000 ft/s). The test sample (target) was placed at the end of the chamber in the flow path. Aluminum 6061, type 316 stainless steel, type 304 stainless steel, and Inconel 718 were ignited with 1600-micron aluminum 2017 particles at elevated temperatures and pressures whereas Monel 400 could not be ignited. The ignition susceptibility of metals and alloys appeared to increase as the inlet pressure, sample temperature, and particle size were increased. Type 304 stainless steel particles required more extreme conditions for ignition of materials than similar sized aluminum particles. The results indicated that ignition and subsequent burning of the particles were required for ignition of the target materials with the possible exception of aluminum 6061.

Benz, F. J.↗

NASA NTRS1988

Modeling of the transient ignition of a nonmetal/oxygen system by heterogeneous reaction - Effects of oxygen pressure

A theoretical model of the transient ignition of a nonmetallic polymer in a pure oxygen environment was developed and used to assess the safety of an oxygen system under elevated pressure. Results demonstrated that, for a general oxygen system, the ignition temperautre is sensitive to the external heating rate as well as such system parameters as the minimum ignition heat flux and the corresponding minimum ignition temperature. As the oxygen pressure increases, the minimum ignition temperature decreases, until, at a sufficiently high oxygen pressure, spontaneous ignition occurs. Numerical results generated by the model were correlated with the reported ignition data for polyethylene, Teflon, and nylon.

Yuen, Walter W.↗

NASA NTRS1989

Ignitability test method and apparatus

An apparatus for testing ignitability of an initiator includes a body with a central cavity, initiator holder for holding the initiator over the central cavity of the body, an ignition material holder disposed in the central cavity of the body and a cavity facing the initiator holder which receives a measured quantity of ignition material to be ignited by the initiator and a chamber in communication with the cavity of the ignition material holder and the central cavity of the body. A measuring system for analyzing pressure characteristics is generated by ignition material by the initiator. The measuring system includes at least one transducer coupled to an oscillograph for recording pressure traces generated by ignition.

Bement, Laurence J.↗

NASA NTRS1993

Ignition and subsequent flame spread over a thin cellulosic material

Both ignition and flame spread on solid fuels are processes that not only are of considerable scientific interest but that also have important fire safety applications. Both types of processes, ignition and flame spread, are complicated by strong coupling between chemical reactions and transport processes, not only in the gas phase but also in the condensed phase. In most previous studies, ignition and flame spread were studied separately with the result that there has been little understanding of the transition from ignition to flame spread. In fire safety applications this transition is crucial to determine whether a fire will be limited to a localized, temporary burn or will transition into a growth mode with a potential to become a large fire. In order to understand this transition, the transient mechanisms of ignition and subsequent flame spread must be studied. However, there have been no definitive experimental or modeling studies, because of the complexity of the flow motion generated by buoyancy near the heated sample surface. One must solve the full Navier-Stokes equations over an extended region to represent accurately the highly unstable buoyant plume and entrainment of surrounding gas from far away. In order to avoid the complicated nature of the starting plume problem under normal gravity, previous detailed radiative ignition models were assumed to be one-dimensional or were applied at a stagnation point. Thus, these models cannot be extended to include the transition to flame spread. The mismatch between experimental and calculated geometries means that theories cannot be compared directly with experimental results in normal gravity. To overcome the above difficulty, theoretical results obtained without buoyancy can be directly compared with experimental data measured in a microgravity environment. Thus, the objective of this study is to develop a theoretical model for ignition and the transition to flame spread and to make predictions using the thermal and chemical characteristics of a cellulosic material which are measured in normal gravity.

Nakabe, Kazuyoshi↗

NASA NTRS1993

A study of ignition phenomena of bulk metals by radiant heating

Early research on combustion of metals was motivated by the knowledge of the large heat release and corresponding high temperatures associated with metal-oxygen reactions. The advent of space flight brought about an increased interest in the ignition and combustion of metallic particles as additives in solid rocket propellants. More recently, attention has been given to the flammability properties of bulk, structural metals due to the number of accidental explosions of metal components in high-pressure oxygen systems. The following work represents a preliminary study that is part of a broader research effort aimed at providing further insight into the phenomena of bulk metal combustion by looking at the effects of gravity on the ignition behavior of metals. The scope of this preliminary experimental study includes the use of a non-coherent, continuous radiation ignition source, the measurement of temperature profiles of a variety of metals and a qualitative observation of the ignition phenomena at normal gravity. The specific objectives of the investigation include: (1) a feasibility study of the use of a continuous radiation source for metal ignition; (2) testing and characterization of the ignition behavior of a variety of metals; and (3) building a preliminary experimental database on ignition of metals under normal gravity conditions.

Branch, Melvin C.↗

NASA NTRS1993

Ignition and combustion of lunar propellants

The ignition and combustion of Al, Mg, and Al/Mg alloy particles in 99 percent O2/1 percent N2 mixtures is investigated at high temperatures and pressures for rocket engine applications. The 20 micron particles contain 0, 5, 10, 20, 40, 60, 80, and 100 weight percent Mg alloyed with Al, and are ignited in oxygen using the reflected shock in a shock tube near the endwall. Using this technique, the ignition delay and combustion times of the particles are measured at temperatures up to 3250 K as a function of Mg content for oxygen pressures of 8.5, 17, and 34 atm. An ignition model is developed which employs a simple lumped capacitance energy equation and temperature and pressure dependent particle and gas properties. Good agreement is achieved between the measured and predicted trends in the ignition delay times. For the particles investigated, the contribution of heterogeneous reaction to the heating of the particle is found to be significant at lower temperatures, but may be neglected as gas temperatures above 3000 K. As little as 10 percent Mg reduces the ignition delay time substantially at all pressures tested. The particle ignition delay times decrease with increasing Mg content, and this reduction becomes less pronounced as oxidizer temperature and pressure are increased.

Burton, Rodney L.↗

NASA NTRS1956

High-temperature oxidation and ignition of metals

A study of the high-temperature oxidation of several aircraft construction materials was undertaken to assess the possibility of ignition under high-temperature flight conditions.Tests have been made both in open and closed jets, and, in addition, the burning of metals has been observed under static conditions in a pressurized vessel containing either air, oxygen, or nitrogen. When heated in an atmosphere of oxygen or when heated and plunged into a supersonic airstream, titanium, iron, carbon steel, and common alloys such as 4130 were found to have spontaneous-ignition temperatures in the solid phase (below melting) and they melted rapidly while burning. Inconel, copper, 18-8 stainless steel, Monel, and aluminum could not be made to ignite spontaneously at temperatures up to melting with the equipment available. Magnesium ignited spontaneously in either type of test at temperatures just above the melting temperature.A theory for the spontaneous ignition of metals, based on the first law of thermodynamics, is presented. Good correlation was obtained between calculated spontaneous-ignition temperatures and values measured in supersonic jet tests. There appears at the present time to be no need for concern regarding the spontaneous ignition of Inconel, the stainless steels, copper, aluminum, or magnesium for ordinary supersonic airplane or missile applications where the material temperature is kept within ordinary structural limits or at least below melting. For hypersonic applications where the material is to be melted away to absorb the heat of convection, the results of the present tests do not apply sufficiently to allow a conclusion.

Hill, Paul R↗

NASA NTRS1995

Discharge ignition behavior of the Space Station plasma contactor

Ignition testing of hollow cathode assemblies being developed for the Space Station plasma contactor system has been initiated to validate reliable multiple restart capability. An ignition approach was implemented that was derived from an earlier arcjet program that successfully demonstrated over 11,600 ignitions. For this, a test profile was developed to allow accelerated cyclic testing at expected operating conditions. To date, one hollow cathode assembly has been used to demonstrate multiple ignitions. A prototype hollow cathode assembly has achieved 3,615 successful ignitions at a nominal anode voltage of 18.0 V. During the ignition testing several parameters were investigated, of which the heater power and pre-heat time were the only parameters found to significantly impact ignition rate.

Sarver-Verhey, Timothy R.↗

NASA NTRS1995

Ignition and subsequent transition to flame spread in a microgravity environment

The fire safety strategy in a spacecraft is (1) to detect any fire as early as possible, (2) to keep any fire as small as possible, and (3) to extinguish any fire as quickly as possible. This suggests that a material which undergoes a momentary, localized ignition might be tolerable but a material which permits a transition to flame spread would significantly increase the fire hazard. Therefore, it is important to understand how the transition from localized ignition to flame spread occurs and what parameters significantly affect the transition. The fundamental processes involved in ignition and flame spread have been extensively studied, but they have been studied separately. Some of the steady state flame models start from ignition to reach a steady state, but since the objective of such a calculation is to obtain the steady state flame spread rate, the calculation through the transition process is made without high accuracy to save computational time. We have studied the transition from a small localized ignition at the center of a thermally thin paper in a microgravity environment. The configuration for that study was axisymmetric, but more general versions of the numerical scheme have been developed by including the effects of a slow, external flow in both two and three dimensions. By exploiting the non-buoyant nature of the flow, it is possible to achieve resolution of fractions of millimeters for 3D flow domains on the order of 10 centimeters. Because the calculations are time dependent, we can study the evolution of multiple flame fronts originating from a localized ignition source. The interaction of these fronts determines whether or not they will eventually achieve steady state spread. Most flame spread studies in microgravity consider two-dimensional flame spread initiated by ignition at one end of a sample strip with or against a slow external flow. In this configuration there is only one flame front. A more realistic scenario involves separate, oppositely directed fronts in two dimensions, or a continuous, radially directed front in three dimensions. We present here some results of both the two and three dimensional codes.

Kashiwagi, Takashi↗

NASA NTRS1994

Ignition and Wind Effects on the Transition to Flame Spread in a Microgravity Environment

The fundamental processes involved in ignition and flame spread have been extensively studied, they are generally studied separately without combining ignition and flame spread through the transition process. Moreover, the majority of the flame spread studies assume steady state flame spread. To study the transient aspects of ignition and the transition to flame spread, a time-dependent numerical model has been developed in which a thin strip is ignited along its width with either a pilot wire, radiative source, or both. For this configuration, the model is two-dimensional. Ignition is initiated away from either end of the sample, and two different flame fronts spread in opposite directions; one flows with and the other against a prescribed external flow. Usually, the flame spread is initiated by ignition at one end of the sample with or against a slow external flow, yielding one flame front. The present configuration is more realistic than the one flame front case because there is interaction between the two flames during the ignition and transition stages.

McGrattan, Kevin B.↗

NASA NTRS1998

Radiative Ignition and Transition to Spread Investigation (RITSI)

A total of 25 experiments was conducted in the Glovebox Facility on the Third United States Microgravity payload (USMP3) mission to study the behavior of both flaming and smoldering ignition events, the transition from ignition to the flame/smoldering spread, and the flame/smoldering growth pattern in air. Twenty one of the 25 experiments were flaming experiments and the remainder were smoldering experiments. Ignition was initiated by a heated wire across a thermally thin filter paper in the middle of the sample for the two-dimensional configuration and by a focused beam from a halogen/tungsten lamp at the center of the sample for the three-dimensional configuration. The external air flow velocity was varied from 0 cm/s to 6.5 cm/s. The ignition and subsequent flame spread events were recorded by a video camera, a 35 mm camera, and 6 thermocouples (2 in the gas phase and 4 in the sample). The results indicate that non-piloted radiative ignition of the paper by external thermal radiation tends to occur more easily than in normal gravity. In the two-dimensional configuration, the transition from ignition to downstream flame spread never occurred; only the transition to upstream spread took place. In the three-dimensional configuration, a char growth pattern emerged in the shape of a fan, with the ignited area as the center of the fan and the fan spreading in the upstream direction. The internal angle of the fan increased with an increase in external flow velocity (higher flow velocity gave a more opened fan pattern). At an external flow velocity of 5 cm/s, the flame was horseshoe-shaped and the char pattern became an elongated semicircle toward upstream. It appears that the peak upstream flame spread rate was reached at a higher external velocity than for the two-dimensional flame front. Flame spread much faster along open edges of the sample paper than along the sample face, presumably due to there being larger supply of oxygen and energy feedback at the open edges than at the surface. These results indicate the possible importance of the effect of the flame front shape such as the curvature of the flame front on spread rate and flame strength. A complex, unexpected finger-shaped char growth pattern was observed during the smoldering experiment. Higher external flow velocity increased the number of localized smoldering fronts, of the char fingers they left behind, and frequency of bifurcations from the fingers. At present, it is not clear what caused such a complex char growth pattern.

Kashiwagi, Takashi↗

NASA NTRS2002

Technology Development of a Fiber Optic-Coupled Laser Ignition System for Multi-Combustor Rocket Engines

This paper addresses the progress of technology development of a laser ignition system at NASA Marshall Space Flight Center (MSFC). The first two years of the project focus on comprehensive assessments and evaluations of a novel dual-pulse laser concept, flight- qualified laser system, and the technology required to integrate the laser ignition system to a rocket chamber. With collaborations of the Department of Energy/Los Alamos National Laboratory (LANL) and CFD Research Corporation (CFDRC), MSFC has conducted 26 hot fire ignition tests with lab-scale laser systems. These tests demonstrate the concept feasibility of dual-pulse laser ignition to initiate gaseous oxygen (GOX)/liquid kerosene (RP-1) combustion in a rocket chamber. Presently, a fiber optic- coupled miniaturized laser ignition prototype is being implemented at the rocket chamber test rig for future testing. Future work is guided by a technology road map that outlines the work required for maturing a laser ignition system. This road map defines activities for the next six years, with the goal of developing a flight-ready laser ignition system.

Trinh, Huu P.↗

NASA NTRS2013

Development and Testing of a Green Monopropellant Ignition System

This paper will detail the development and testing of a "green" monopropellant booster ignition system. The proposed booster ignition technology eliminates the need for a pre-heated catalyst bed, a high wattage power source, toxic pyrophoric ignition fluids, or a bi-propellant spark ignitor. The design offers the simplicity of a monopropellant feed system features non-hazardous gaseous oxygen (GOX) as the working fluid. The approach is fundamentally different from all other "green propellant" solutions in the aerospace in the industry. Although the proposed system is more correctly a "hybrid" rocket technology, since only a single propellant feed path is required, it retains all the simple features of a monopropellant system. The technology is based on the principle of seeding an oxidizing flow with a small amount of hydrocarbon.1 The ignition is initiated electrostatically with a low-wattage inductive spark. Combustion gas byproducts from the hydrocarbon-seeding ignition process can exceed 2400 C and the high exhaust temperature ensures reliable main propellant ignition. The system design is described in detail in the Hydrocarbon-Seeded Ignition System Design subsection.

Whitmore, Stephen A.↗

DOE OSTI2025

A novel ignition model for low velocity impact of heterogeneous explosives based on interacting hot spots

While numerous studies have focused on the ignition of explosives occurring in high velocity impact and the associated shock-to-detonation transition, there has been growing interest in developing computational models focused on low-velocity impact regimes. A predictive low-velocity impact ignition model will be important for analyzing high explosive safety and potential accident scenarios. This work introduces a novel ignition model based on the concept of thermally interacting hot spots to simulate low velocity impacted heterogeneous explosives where observed ignition times are on the order of milliseconds. The model asserts that relevant hot spots are micron-sized, the typical separation between neighboring hot spots is on the order of a hundred microns, and that neighbors interact thermally through heat conduction across the interstitial region between them. To achieve tractable numerical solutions, hot spots are assumed to form a periodic array as opposed to the highly irregular positioning in an actual explosive. This idealization allows a single two hotspot system to characterize the ignition process. Consequently, the model is referred to as the two hot spot Frank-Kamenetskii ignition model. In the present study, hot spots are modeled as constant heat sources terms, but this can be extended to include grain-scale phenomena like frictional heating of micron-sized growing cracks that are confined under high pressure. Because the micron-sized features are below the scale that can be efficiently resolved at a systems level, an efficient subscale scheme based on the Method of Weighted Residuals (MWR) is used to efficiently solve the equations. In conclusion, we carry out numerical examples and analytic predictions illustrating the accuracy and the functioning of the model.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2025

Exploring scenarios for enhanced fuel compression and performance on the National Ignition Facility with machine-learning-aided design techniques

Recent fusion experiments on the National Ignition Facility (NIF) have achieved ignition, producing multi-MJ fusion yields for input laser energies of roughly 2 MJ [Abu-Shawareb et al., Phys. Rev. Lett. 132, 065102 (2024)]. Building on the success of the target designs that have achieved ignition, we explore new implosion scenarios predicted to generate significantly more compression of the dense DT ice layer and correspondingly higher yields while preserving many of the key physics characteristics of present-day ignition designs. Our main result is a novel 3-shock implosion scheme that effectively minimizes the shock-induced entropy in the dense, accelerating DT shell and maximizes the resulting fuel compression subject to a fixed leading shock strength consistent with present-day ignition experiments, which is necessary to melt the crystalline high-density carbon ablator. Compared to the first NIF experiment to fulfill Lawson's ignition criterion, shot N210808 [Abu-Shawareb et al., Phys. Rev. Lett. 129, 075001 (2022)], our design exhibits a 40% increase in simulated peak areal density (ρR) and a 5× increase in 1D fusion yield using a 4% lighter ablator and identical DT payloads. We also present a complete integrated 2D hohlraum design and laser pulse specifications capable of generating the desired 3-shock drive and maintaining control of the low-mode capsule implosion symmetry, where the increase in simulated 2D yield relative to N210808 is > 10×. This new implosion regime was discovered with help from a machine-learning-enabled capsule design optimization framework. We outline the workflow this automated tool uses to identify improved design candidates by running several rounds of capsule simulations, constructing a surrogate model mapping input variations to key physics output quantities, and querying the resulting statistical model to propose adjustments to the x-ray drive and capsule to reach a set of physics objectives prescribed by the designer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Temperature Distribution Within an Ignition Kernel Initiated by a Laser-Induced Plasma

The sizes of, and temperature distributions within, ignition kernels initiated by a Q-switched neodymium-doped yttrium aluminum garnet laser-induced plasma in an unconfined lean premixed hydrogen-air upward jet flow are investigated. The experiments involved a range of jet velocities and a range of deposited laser energies at a fixed height above the exit along the axis of a burner. The growth of, and the temperature distributions within, the ignition kernels, as affected by the size and the energy distribution of the laser-induced plasma, are monitored with an infrared camera. The initial ignition kernels’ areas are larger with higher laser pulse energies and remain unchanged up to [Formula: see text] and then increase by factors of up to 3 at [Formula: see text]. The change in the kernel area caused by the jet velocities is less than 1.5%. An increase of the bulk velocity by 190% decreases the ignition kernel temperature by 6%. This reduction in the ignition kernel temperatures is because of an increase in energy losses by a factor of 2 and decreases in heat releases by 2% at [Formula: see text] and by 11% at [Formula: see text]. The present contributions are: measurements of and insights into temperature distributions and kernel development rates during the laser-induced plasma ignition process at different deposited energies and flow velocities.

Engineering↗