SEARCH · Search NASA

Results for “INTERFERENCE - PROPELLER & FUSELAGE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS1955

Aerodynamic Loads on an External Store Adjacent to a 45 Degree Sweptback Wing at Mach Numbers from 0.70 to 1.96, Including an Evaluation of Techniques Used

Aerodynamic forces and moments have been obtained in the Langley 9- by 12-inch blowdown tunnel on an external store and on a 45 degree swept-back wing-body combination measured separately at Mach numbers from 0.70 to 1.96. The wing was cantilevered and had an aspect ratio of 4.0; the store was independently sting-mounted and had a Douglas Aircraft Co. (DAC) store shape. The angle of attack range was from -3 degrees to 12 degrees and the Reynolds number (based on wing mean aerodynamic chord) varied from 1.2 x10(6) to 1.7 x 10(6). Wing-body transonic forces and moments have been compared with data of a geometrically similar full-scale model tested in the Langley 16-foot and 8-foot transonic tunnels in order to aid in the evaluation of transonic-tunnel interference. The principal effect of the store, for the position tested, was that of delaying the wing-fuselage pitch-up tendency to higher angles of attack at Mach numbers from 0.70 to 0.90 in a manner similar to that of a wing chord extension. The most critical loading condition on the store was that due to side force, not only because the loads were of large magnitude but also because they were in the direction of least structural strength of the supporting pylon. These side loads were greatest at high angles of attack in the supersonic speed range. Removal of the supporting pylon (or increasing the gap between the store and wing) reduced the values of the variation of side-force coefficientwith angle of attack by about 50 percent at all test Mach numbers, indicating that important reductions in store side force may be realized by proper design or location of the necessary supporting pylon. A change of the store skew angle (nose inboard) was found to relieve the excessive store side loads throughout the Mach number range. It was also determined that the relative position of the fuselage nose to the store can appreciably affect the store side forces at supersonic speeds.

Guy, Lawrence D↗

NASA NTRS2016

Parallel Adjective High-Order CFD Simulations Characterizing SOFIA Cavity Acoustics

This paper presents large-scale MPI-parallel computational uid dynamics simulations for the Stratospheric Observatory for Infrared Astronomy (SOFIA). SOFIA is an airborne, 2.5-meter infrared telescope mounted in an open cavity in the aft fuselage of a Boeing 747SP. These simulations focus on how the unsteady ow eld inside and over the cavity interferes with the optical path and mounting structure of the telescope. A temporally fourth-order accurate Runge-Kutta, and spatially fth-order accurate WENO- 5Z scheme was used to perform implicit large eddy simulations. An immersed boundary method provides automated gridding for complex geometries and natural coupling to a block-structured Cartesian adaptive mesh re nement framework. Strong scaling studies using NASA's Pleiades supercomputer with up to 32k CPU cores and 4 billion compu- tational cells shows excellent scaling. Dynamic load balancing based on execution time on individual AMR blocks addresses irregular numerical cost associated with blocks con- taining boundaries. Limits to scaling beyond 32k cores are identi ed, and targeted code optimizations are discussed.

CFD↗

NASA NTRS2015

Parallel Adaptive High-Order CFD Simulations Characterizing SOFIA Cavitiy Acoustics

This paper presents large-scale MPI-parallel computational uid dynamics simulations for the Stratospheric Observatory for Infrared Astronomy (SOFIA). SOFIA is an airborne, 2.5-meter infrared telescope mounted in an open cavity in the aft fuselage of a Boeing 747SP. These simulations focus on how the unsteady ow eld inside and over the cavity interferes with the optical path and mounting structure of the telescope. A tempo- rally fourth-order accurate Runge-Kutta, and a spatially fth-order accurate WENO-5Z scheme were used to perform implicit large eddy simulations. An immersed boundary method provides automated gridding for complex geometries and natural coupling to a block-structured Cartesian adaptive mesh re nement framework. Strong scaling studies using NASA's Pleiades supercomputer with up to 32k CPU cores and 4 billion compu- tational cells shows excellent scaling. Dynamic load balancing based on execution time on individual AMR blocks addresses irregular numerical cost associated with blocks con- taining boundaries. Limits to scaling beyond 32k cores are identi ed, and targeted code optimizations are discussed.

Parallell↗

NASA NTRS1985

Computer studies of hybrid slotted working sections with minimum steady interference at subsonic speeds

Currently there is renewed interest in the evaluation and reduction of steady wind tunnel wall interference, especially for large models. Evaluation of previous predictions for perforated and slotted tunnels suggests that a hybrid slotted tunnel (i.e., a slotted tunnel with closed slats and perforated slots) should offer minimum corrections for upwash, flow curvature and solid blockage. This suggestion is confirmed by the present computer studies of a range of rectangular hybrid slotted tunnels. The computer studies are for tunnel working section height to breadth ratios of 0.835 and 0.600 over the Mach number range from 0 to 0.85. Wings swept at 28 deg and 50 deg, with ratios of model span to tunnel breadth varying from 0 to 0.7, are considered. An idealized fuselage shape is used to predict solid and wake blockage corrections for the wall configurations selected on the basis of minimum upwash and curvature interference.

Mabey, D. G.↗

NASA NTRS1973

Pressure loads and aerodynamic force information for the -89A space shuttle orbiter configuration, volume 2

Experimental aerodynamic investigations were conducted on an 0.0405 scale representation of the Rockwell -89A Light Weight Space Shuttle Orbiter. The test purpose was to obtain pressure loads data in the presence of the ground for orbiter structural strength analysis. Aerodynamic force data was also recorded to allow correlation with all pressure loads information. Angles of attack from minus 3 deg to 18 deg and angles of sideslip of 0 deg, plus or minus 50 deg, and plus or minus 10 deg were tested in the presence of the NAAL ground plane. Static pressure bugs were used to obtain a pressure loads survey of the basic configuration, elevon deflections of 5 deg, 10 deg, 15 deg, and minus 20 deg and a rudder deflection of minus 15 deg, at a tunnel dynamic pressure of 40 psi. The test procedure was to locate a maximum of 30 static pressure bugs on the model surface at various locations calculated to prevent aerodynamic and physical interference. Then by various combinations of location the pressure bugs output was to define a complete pressure survey for the fuselages, wing, vertical tail, and main landing gear door.

Mennell, R. C.↗

NASA NTRS1971

Preliminary wind-tunnel investigation of the effects of engine nacelles on a transport configuration with high lift drag ratios to a Mach number of 1.00

Wind tunnel tests to determine the effect of engine nacelles added to a low wing fuselage vertical tail configuration utilizing the NASA supercritical airfoil and a refined area ruled fuselage are discussed. The engine arrangement consisted of two aft fuselage, side mounted flow through nacelles and a solid body of revolution mounted above the fuselage in a manner similar to the Boeing 727. A preliminary analysis of the wind tunnel data shows that favorable interference drag can be obtained with the proper longitudinal locations of the nacelles, by canting the nacelle inlets, and by cusping the rearward region of the nacelle.

Flechner, S. G.↗

NASA NTRS1996

Modeling of Sound Transmission through Shell Structures with Turbulent Boundary Layer Excitation

The turbulent boundary layer (TBL) pressure field is an important source of cabin noise during cruise of high subsonic and supersonic commercial aircraft. The broadband character of this excitation field results in an interior noise spectrum that dominates the overall sound pressure level (SPL) and speech interference metrics in the forward and midcabins of many aircraft. In the authors' previous study, sound transmission through an aircraft fuselage, modeled by two concentric cylindrical sandwich shells and excited by a TBL statistical model was investigated analytically. An assessment of point and global structural vibration levels and resulting interior noise levels was obtained for different TBL models, flight conditions and fuselage structural designs. However, due to the complication of the shell structure, the important noise transmission mechanisms were difficult to discern. Previous experience has demonstrated that a fundamental understanding of the range of modes (or wavenumbers) generated by the TBL source both in the structure and the acoustic cavity is key to the development of both active and passive control technologies. In an initial effort to provide this insight, the objective of this paper is to develop an analytical model of sound transmission through a simple unstiffened cylindrical aluminum shell excited by a TBL pressure field. The description of the turbulent pressure field is based on the Corcos formulation for the cross-spectral density (CSD) of the pressure fluctuations. The coupled shell and interior and exterior acoustic equations are solved for the structural displacement and the interior acoustic response using a Galerkin approach to obtain analytical solutions. Specifically, this study compares the real part of the normalized CSD of the TBL excitation field, the structural displacement and the interior acoustic field. Further the modal compositions of the structural and cavity response are examined and some inference of the dominant mechanism of noise transmission is made.

Tang, Yvette Y.↗

NASA NTRS2002

Turbulent Navier-Stokes Flow Analysis of an Advanced Semispan Diamond-Wing Model in Tunnel and Free Air at High-Lift Conditions

Turbulent Navier-Stokes computational results are presented for an advanced diamond wing semispan model at low-speed, high-lift conditions. The numerical results are obtained in support of a wind-tunnel test that was conducted in the National Transonic Facility at the NASA Langley Research Center. The model incorporated a generic fuselage and was mounted on the tunnel sidewall using a constant-width non-metric standoff. The computations were performed at to a nominal approach and landing flow conditions.The computed high-lift flow characteristics for the model in both the tunnel and in free-air environment are presented. The computed wing pressure distributions agreed well with the measured data and they both indicated a small effect due to the tunnel wall interference effects. However, the wall interference effects were found to be relatively more pronounced in the measured and the computed lift, drag and pitching moment. Although the magnitudes of the computed forces and moment were slightly off compared to the measured data, the increments due the wall interference effects were predicted reasonably well. The numerical results are also presented on the combined effects of the tunnel sidewall boundary layer and the standoff geometry on the fuselage forebody pressure distributions and the resulting impact on the configuration longitudinal aerodynamic characteristics.

Ghaffari, Farhad↗

NASA NTRS2002

Numerical Viscous Flow Analysis of an Advanced Semispan Diamond-Wing Model at High-Life Conditions

Turbulent Navier-Stokes computational results are presented for an advanced diamond wing semispan model at low speed, high-lift conditions. The numerical results are obtained in support of a wind-tunnel test that was conducted in the National Transonic Facility (NTF) at the NASA Langley Research Center. The model incorporated a generic fuselage and was mounted on the tunnel sidewall using a constant width standoff. The analyses include: (1) the numerical simulation of the NTF empty, tunnel flow characteristics; (2) semispan high-lift model with the standoff in the tunnel environment; (3) semispan high-lift model with the standoff and viscous sidewall in free air; and (4) semispan high-lift model without the standoff in free air. The computations were performed at conditions that correspond to a nominal approach and landing configuration. The wing surface pressure distributions computed for the model in both the tunnel and in free air agreed well with the corresponding experimental data and they both indicated small increments due to the wall interference effects. However, the wall interference effects were found to be more pronounced in the total measured and the computed lift, drag and pitching moment due to standard induced up-flow effects. Although the magnitudes of the computed forces and moment were slightly off compared to the measured data, the increments due the wall interference effects were predicted well. The numerical predictions are also presented on the combined effects of the tunnel sidewall boundary layer and the standoff geometry on the fuselage fore-body pressure distributions and the resulting impact on the overall configuration longitudinal aerodynamic characteristics.

Ghaffari, F.↗

NASA NTRS2018

CLAS-ACT: Conformal, Lightweight Antennas for Aeronautical Communications Technology

The growing demand for Unmanned Aerial Vehicles (UAVs) and operating them beyond the line of sight (BLOS) has resulted in an increased interest in using existing satellite communication capabilities for command, control, and telemetry (CC&T). As the user base in this allocated portion of the spectrum expands, there is an increased potential for interference with existing terrestrial fixed-point communication systems. As secondary users, UAVs must seek out new solutions to avoid interfering with these existing ground sites while maintaining good links with satellite constellations. In this presentation, a novel lightweight conformal phased array antenna currently under development is presented that can use null steering and/or beam shaping to avoid ground interference while simultaneously providing strong satellite microwave links for communications. The reduced weight of this design and ability to integrate into the fuselage of smaller UAV platforms will also be discussed as a potential solution to provide BLOS operation via spectrum sharing for an expanding user base.

Meador, Mary Ann↗

NASA NTRS1972

Effect of wing sweep, angle of attack, Reynolds number, and wing root fillet on the interference heating to the wing windward surface of an entry vehicle configuration

The phase-change-coating technique was used to study the interference heating to the windward surface of 14 deg, 25 deg, and 50 deg swept wings of an entry vehicle configuration. One wing root of each model was faired to the fuselage with a fillet. Tests were made at Mach 8 at angles of attack of 0 deg, 20 deg, 40 deg, and 60 deg and at free-stream Reynolds numbers based on model length of 0.47 and 1.7 million. Bow shock impingement heating was found to increase in magnitude and affected area with increasing angle of attack until at a higher angle of attack it decreases; this angle of attack is lower for a 50 deg swept wing. Wing root interference heating was found to increase with angle of attack up to 40 deg and then to remain approximately constant. Consequently, wing root interference heating becomes the major type of interference heating at large angles of attack, and this occurs at a lower angle of attack for the highest sweep angle. A wing leading-edge root fillet reduces the peak in wing root interference heating near the leading edge, and increasing Reynolds number increases the level of interference heating.

Clark, L. E.↗

NASA NTRS1983

Studies of light-twin wing-body interference

The results of an analytical study of aerodynamic interference effects for a light twin aircraft are presented. The data presented concentrates on the influence of a wing on a body (the fuselage). Wind tunnel comparisons of three fillets are included, with corresponding computational analysis. Results indicate that potential flow analysis is useful to guide the design of intersection fairings, but experimental tuning is still required. While the study specifically addresses a light twin aircraft, the methods are applicable to a wide variety of aircraft.

Thomson, W. G.↗

NASA NTRS1961

A Wind-Tunnel Investigation of a Transonic-Transport Configuration Utilizing Drag-Reducing Devices at Mach Numbers from 0.20 to 1.03

The static longitudinal stability and control and lateral characteristics of a transonic-transport model, incorporating recent drag-reducing devices, has been investigated in the Langley 8-foot transonic pressure tunnel. The wing was cambered, had a thickened root and a taper ratio of 0.3. Wing sweepback angles of 45 degrees and 40 degrees were investigated with corresponding aspect ratios of 7 and 8, respectively. Modifications to the model for reducing the drag were: a forward fuselage addition and special bodies (four big enough to house jet engines) added to the upper surface of the wing. Other components and changes investigated included an empennage, a wing-tip body, wing fences, wing trailing-edge flaps, horizontal-tail settings, and wing dihedral angle. The investigation covered the Mach number range from 0.20 to 1.03 for the angle-of-attack range from -5 degrees to 15.4 degrees, and a sideslip angle of -5 degrees, in the Reynolds number range from 0.52 times 10(exp 6) to 1.94 times 10(exp 6) based on the wing mean aerodynamic chord. The various fuselage and wing additions delayed the drag-rise Mach number and greatly reduced the drag beyond the drag rise. The wing bodies markedly alleviated unstable pitch tendencies throughout the test Mach number range. At low landing speeds, the wing bodies exhibited little interference with the ability of trailing-edge flaps to increase the lift near maximum lift coefficient; and the use of fences greatly reduced the severe longitudinal instability trend at landing attitudes. The model with a 6 degree dihedral angle exhibited positive lateral and directional stability characteristics in the presence of the fuselage and wing additions. An increase in drag-rise Mach number associated with the fuselage and wing additions on the 40 degree sweptback wing combination was similar to that for the comparable 45 degree combination. These additions did, however, reduce the drag of the 40 degree sweptback configurations more than the 45 degree configurations in the transonic speed range.

Loving, Donald L.↗

NASA NTRS1983

Experimental study of main rotor/tail rotor/airframe interactions in hover. Volume 1: Text and figures

To assist in identifying and quantifying the relevant parameters associated with the complex topic of main rotor/fuselage/tail rotor interference, a model scale hover test was conducted in the Model Rotor Hover Facility. The test was conducted using the basic model test rig, fuselage skins to represent a UH-60A BLACK HAWK helicopter, 4 sets of rotor blades of varying geometry (i.e., twist, airfoils and solidity) and a model tail rotor that could be relocated to give changes in rotor clearance (axially, laterally, and vertically), can't angle and operating model (pusher or tractor). The description of the models and the tests, data analysis and summary (including plots) are included. The customary system of units gas used for principal measurements and calculations. Expressions in both SI units and customary units are used with the SI units stated first and the customary units afterwords, in parenthesis.

Balch, D. T.↗

NASA NTRS1975

A free flight investigation of transonic sting interference

Transonic sting interference has been studied in a supersonic wind tunnel to obtain free flight and sting support data on identical models. The two principal configurations, representing fuselage bodies, were cigar shaped with tail fins. The others were a sharp 10-deg cone, a sphere, and a blunt entry body. Comparative data indicated that the sting had an appreciable effect on drag for the fuselage-like configurations; drag rise occurred 0.02 Mach number earlier in free flight, and drag level was 15% greater. The spheres and the blunt bodies were insensitive to the presence of stings regardless of their size. The 10-deg cones were in between, experiencing no drag difference with a minimum diameter sting, but a moderate difference with the largest diameter sting tested. All data tend to confirm the notion that for the more slender bodies the sting not only affects flow but the forebody flow as well.

Jaffe, P.↗

NASA NTRS1940

High-Speed Tests of a Model Twin-Engine Low-Wing Transport Airplane

Force tests were made of a 1/8-scale model of a twin-engine low-wing transport airplane in the NACA 8-foot high-speed wind tunnel to investigate compressibility and interference effects at speeds up to 450 miles per hour. In addition to tests of the standard arrangement of the model tests were made with several modifications designed to reduce the drag and to increase the critical speed. The results show serious increases in drag at critical speeds below 450 miles per hour due to the occurrence of compressibility burbles on the standard radial-engine cowlings, on sections of the wing as a result of wing-nacelle interference, and on the semi-retracted main landing wheels. The critical speed at which the shock occurred on the standard cowlings was 20 miles per hour lower in the presence of the fuselage than in the presence of the wing only. The drag of the complete model was reduced 25% at 300 miles per hour by completely retracting the landing gear, fairing the windshield irregularities, and substituting streamline nacelles (with allowance made for the proper amount of cooling-air flow) for the standard nacelle arrangement. The values of the critical Mach number were extended from 0.47 to 0.60 as a result of the aforementioned improvements. The principal purpose of the reported tests was to investigate the effect of compressibility on the drag of the component parts of a representative large airplane and on the overall drag of such an airplane. The influence of interference on compressibility effects was also studied. In addition, it was proposed to test several modifications of the standard component parts that gave promise of an improvement in aerodynamic characteristics.

Becker, John V.↗

NASA NTRS1954

On the determination of certain basic types of supersonic flow fields

A discussion is given of the application of Fourier series techniques to the problems of linearized supersonic flow. The formulation presented is an extension of the doublet type of "fundamental solution" to higher order types of singularity. The equations developed have application to wing theory but are primarily of importance in wing-body interaction problems. A specific example of a wing-body interference problem is discussed in light of the presented methods.

BODIES - AERODYNAMIC THEORY↗

NASA NTRS1998

The Real-Time Wall Interference Correction System of the NASA Ames 12-Foot Pressure Wind Tunnel

An improved version of the Wall Signature Method was developed to compute wall interference effects in three-dimensional subsonic wind tunnel testing of aircraft models in real-time. The method may be applied to a full-span or a semispan model. A simplified singularity representation of the aircraft model is used. Fuselage, support system, propulsion simulator, and separation wake volume blockage effects are represented by point sources and sinks. Lifting effects are represented by semi-infinite line doublets. The singularity representation of the test article is combined with the measurement of wind tunnel test reference conditions, wall pressure, lift force, thrust force, pitching moment, rolling moment, and pre-computed solutions of the subsonic potential equation to determine first order wall interference corrections. Second order wall interference corrections for pitching and rolling moment coefficient are also determined. A new procedure is presented that estimates a rolling moment coefficient correction for wings with non-symmetric lift distribution. Experimental data obtained during the calibration of the Ames Bipod model support system and during tests of two semispan models mounted on an image plane in the NASA Ames 12 ft. Pressure Wind Tunnel are used to demonstrate the application of the wall interference correction method.

Ulbrich, Norbert↗