Search NASA⌕ Search

SEARCH · Search NASA

Results for “INTERNAL FRICTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Liquid Motion Experiment Flown on STS-84

During some part or all of each mission, about half of all scientific and commercial spacecraft will spin. For example, commercial spacecraft are made to spin during the transfer maneuver from low Earth orbit to the mission orbit to obtain gyroscopic stiffness. Many spacecraft spin continuously in orbit for the same reason. Other reasons for spinning include controlling the location of liquid propellants within their tanks and distributing solar heat loads. Although spinning has many benefits, it also creates problems because of the unavoidable wobble motion that accompanies spinning. Wobbling makes the spacecraft's flexible components oscillate. The energy dissipated by the internal friction of these components causes the wobbling amplitude to increase continually until, at some point, the attitude control thrusters must be fired to bring the spacecraft's amplitude back to an acceptable level.

Dalton, Penni J.↗
NASA NTRS2003

Strength Differential Measured in Inconel 718: Effects of Hydrostatic Pressure Studied

Aeropropulsion components, such as disks, blades, and shafts, are commonly subjected to multiaxial stress states at elevated temperatures. Experimental results from loadings as complex as those experienced in service are needed to help guide the development of accurate viscoplastic, multiaxial deformation models that can be used to improve the design of these components. During a recent study on multiaxial deformation (ref. 1) on a common aerospace material, Inconel 718, it was shown that the material in the aged state exhibits a strength differential effect (SDE), whereby the uniaxial compressive yield and subsequent flow behavior are significantly higher than those in uniaxial tension. Thus, this material cannot be described by a standard von Mises yield formulation. There have been other formulations postulated (ref. 2) that involve other combinations of the stress invariants, including the effect of hydrostatic stress. The question remained as to which invariants are necessary in the flow model. To capture the physical mechanisms occurring during deformation and reflect them in the plasticity formulation, researchers examined the flow of Inconel 718 under various amounts of hydrostatic stress to determine whether or not hydrostatic stress is needed in the formulation. Under NASA Grant NCC3-464, monitored by the NASA Glenn Research Center, a series of tensile tests were conducted at Case Western Reserve University on aged (precipitation hardened) Inconel 718 at 650 C and with superimposed hydrostatic pressure. Dogbone shaped tensile specimens (3-mm-diameter gauge by 16-mm gauge length) and cylindrical compression specimens (3-mm-diameter gauge by 6-mm gauge length) were strain gauged and loaded in a high-pressure testing apparatus. Hydrostatic pressures were obtained with argon and ranged from 210 to 630 MPa. The aged Inconel 718 showed a pronounced difference in the tension and compression yield strength (i.e., an SDE), as previously observed. Also, there were no significant effects of hydrostatic pressure on either the tensile and compressive yield strength (see the graph) or on the magnitude of the SDE. This behavior is not consistent with the pressure-dependent theory of the SDE, which postulates that the SDE is associated with pressure-dependent and/or internal friction dependent deformation associated with non-Schmid effects at the crystal level (refs. 3 and 4). Flow in Inconel 718 appears to be independent of hydrostatic pressure, suggesting that this invariant may be removed from the phenomenological constitutive model. As part of an ongoing effort to develop advanced constitutive models, Glenn s Life Prediction Branch coordinated this work with that of research on the multiaxial deformation behavior of Inconel 718 being conducted at Pennsylvania State University under NASA Grant NCC597.

Lewandowski, John J.↗
NASA NTRS2008

Numerical Analysis of Rocket Exhaust Cratering

Supersonic jet exhaust impinging onto a flat surface is a fundamental flow encountered in space or with a missile launch vehicle system. The flow is important because it can endanger launch operations. The purpose of this study is to evaluate the effect of a landing rocket s exhaust on soils. From numerical simulations and analysis, we developed characteristic expressions and curves, which we can use, along with rocket nozzle performance, to predict cratering effects during a soft-soil landing. We conducted a series of multiphase flow simulations with two phases: exhaust gas and sand particles. The main objective of the simulation was to obtain the numerical results as close to the experimental results as possible. After several simulating test runs, the results showed that packing limit and the angle of internal friction are the two critical and dominant factors in the simulations.

Source record↗
NASA NTRS2010

Temperature-Dependent Electrical and Micromechanical Properties of Lanthanum Titanate with Additions of Yttria

Temperature-dependent elastic properties were determined by establishing continuous flexural vibrations in the material at its lowest resonance frequency of 31tHz. The imaginary part of the complex impedance plotted as a function of frequency and temperature reveals a thermally activated peak, which decreases in magnitude as the temperature increases. Additions of yttria do not degrade the electromechanical in particularly the elastic and anelastic properties of lanthanum titanate. Y2O3/La2Ti2O7 exhibits extremely low internal friction and hence may be more mechanical fatigue-resistant at low strains.

Goldsby, Jon C.↗
NASA NTRS2019

Deviation of the Shape of Bennu from Rotational Figures of Stability

Images of asteroid (101955) Bennu acquired by the OSIRIS-­REx mission reveal a rocky world covered in rubble; Shape deviates from hydrostatic surface; Internal friction and/or cohesion even if no tensile strength; Understanding the deviation of the surface from idealized shape may help constrain mechanical properties of the interior; Geologic evolution of Bennu is driven by downslope migration of surface material and rubble; May be caused by YORP-induced spin-up, re-­accumulation, impact-induced seismic shaking, thermal stresses, or tidal disruption by close encounters to larger bodies.

Roberts, J. H.↗
NASA NTRS2020

Barefoot Rover: a Sensor-Infused Rover Wheel Demonstrating In-Situ Engineering and Science Extractions using Machine Learning

In this work, we demonstrate an instrumented wheel concept which utilizes a 2D pressure grid, an electrochemical impedance spectroscopy (EIS) sensor and machine learning (ML) to extract meaningful metrics from the interaction between the wheel and surface terrain. These include continuous slip/skid estimation, balance, and sharpness for engineering applications. Estimates of surface hydration, texture, terrain patterns, and regolith physical properties such as cohesion and angle of internal friction are additionally calculated for science applications. Traditional systems rely on post-processing of visual images and vehicle telemetry to estimate these metrics. Through in-situ sensing, these metrics can be calculated in near real time and made available to onboard science and engineering autonomy applications. This work aims to provide a deployable system for future planetary exploration missions to increase science and engineering capabilities through increased knowledge of the terrain.

Marchetti, Yuliya↗
NASA NTRSDate not supplied

Experimental Considerations for Ground-based Testing of Lunar Construction Technologies

The Moon-to-Mars Planetary Autonomous Construction Technology (MMPACT) project, under NASA’s Game Changing Division (GCD) aims to research, develop, and demonstrate lunar surface construction capabilities[1].A fundamental step in lunar infrastructure development is to quantify the geotechnical properties of lunar regolith, such as shear strength (Mohr-Coulomb cohesion and angle of internal friction), com-pression and bearing properties, and angle of re-pose. Knowledge of these geotechnical properties enables the prediction of forces and displacements associated with lunar infrastructure development processes including excavation and constructing landing pads, habitats, shelters, and roadways. Through ground-based testing of autonomous lunar systems performed using relevant hardware (e.g., robotic arms) in appropriate lunar regolith simulants, the developed hardware/technology and tool paths can be validated. Such testing also generates data to give insight into the geotechnical regolith properties on the lunar surface.

Regolith↗
NASA NTRSDate not supplied

LUNAR REGOLITH:SMALL SCALE ROBOTIC SITE PREPARATION AND GEOTECHNICAL EXPERIMENTSWITH SCOOPS

NASA’s Moon-To-Mars Planetary Autonomous Construction Technology (MMPACT) project seeks to research, develop, and demonstrate lunar surface construction capabilities. Quantification of lunar regolith’s geotechnical properties allows for effective prediction of forces and displacement during excavation and construction and is critical to facilitating regolith sintering capabilities all of which benefit lunar infrastructure plans. Knowledge of shear strength, Mohr-Coulomb cohesion, angle of internal friction, bearing strength, bulk density, etc. is needed. The use of ground-based testing of various lunar simulants with relevant hardware (e.g., robotic arm tools) enables validation of technology choices, tool paths, and lunar surface construction activities. In addition, the use of Taguchi methods will minimize the number of needed experiments to explore critical input parameters.

R. P. Mueller↗
NASA NTRSDate not supplied

Experimental Considerations for Ground-Based Testing of Lunar Construction Technologies

NASA’s Moon-To-Mars Planetary Autonomous Construction Technology (MMPACT) project seeks to research, develop, and demonstrate lunar surface construction capabilities - Quantification of lunar regolith’s geotechnical properties allows for effective prediction of forces and displacement during excavation and construction and is critical to facilitating regolith sintering capabilities all of which benefit lunar infrastructure plans - Knowledge of shear strength, Mohr-Coulomb cohesion, angle of internal friction, bearing strength, bulk density, etc. is needed - Ground-based testing of various lunar simulants with relevant hardware (e.g., robotic arm tools) enables validation of technology choices, tool paths, and lunar surface construction activities - Use of Taguchi methods [1] will minimize the number of needed experiments to explore critical input parameter

Moon↗
NASA NTRSDate not supplied

Lunar Regolith: Small Scale Robotic Site Preparation and Geotechnical Experiments with Scoops

- NASA’s Moon-To-Mars Planetary Autonomous Construction Technology (MMPACT) project seeks to research, develop, and demonstrate lunar surface construction capabilities. - Quantification of lunar regolith’s geotechnical properties allows for effective prediction of forces and displacement during excavation and construction and is critical to facilitating regolith sintering capabilities all of which benefit lunar infrastructure plans. - Knowledge of shear strength, Mohr-Coulomb cohesion, angle of internal friction, bearing strength, bulk density, etc. is needed. - The use of ground-based testing of various lunar simulants with relevant hardware (e.g., robotic arm tools) enables validation of technology choices, tool paths, and lunar surface construction activities. - In addition, the use of Taguchi methods [1] will minimize the number of needed experiments to explore critical input parameters. - The Jet Propulsion Lab is preparing to fly the COLDarm payload on a CLPS lunar mission with a geotechnical measurement scoop

Regolith↗
NASA NTRSDate not supplied

Quantitative Characterization of Lunar Regolith Simulants for Direct Comparison to Apollo Soil Samples

Introduction: Sustained characterization efforts of lunar regolith simulant properties are not only integral for verification of commercially-produced material designed for a wide array of testing applications but are also necessary in establishing a comprehensive comparison to a lunar reference source. As a resource for the lunar science and engineering communities, the Simulant Development Lab (SDL) within the Astromaterials Research & Exploration Science (ARES) division at the Johnson Space Center (JSC) is actively pursuing closure of existing knowledge gaps in fundamental simulant attributes, including chemistry, mineralogy, particle size distribution, particle geometry, bulk and relative density, magnetic susceptibility, and shear strength (i.e., cohesion and angle of internal friction), as well as producing Figures of Merit for comparison of lunar simulants to Apollo regolith samples.

R. Kovtun↗
NASA NTRS2024

Characterization of NUW-LHT-5m, A Lunar Highland Simulant

A new simulant of the lunar highlands regolith, NUW-LHT-5M, was designed by NASA and manufactured by Washington Mills. The simulant was based on Apollo 16 data and is a member of the NU-LHT-series. NASA’s Marshall Space Flight Center and Johnson Space Center have already purchased 3 metric tons of the simulant for advanced engineering work. In support of engineering uses of the simulant, we provided measurements of the simulant including: mineral abundance and composition, liberation, X-ray fluorescence (XRF), ferrous iron, carbon, sulfur, 60 element inductively coupled plasma (ICP), loss on ignition, particle size, both 2D and 3D particle shape, specific surface area, shear, cohesion, internal friction, helium pycnometry, minimum index density, tap density, magnetic susceptibility, cryogenic and high temperature permittivity, visible and near-infrared (VNIR) and middle infra-red spectroscopy (MIR), differential scanning calorimetry (DSC), viscosity, thermal diffusivity, thermal conductivity, thermal gravimetric analysis (TGA), evolved gas analysis (EGA), and spark sintering. For the crystalline components the design of the simulant called for two rocks from the Stillwater Complex, Montana: 17.6 wt% norite, 37.7% anorthosite, and 4.7 wt% olivine from an unspecified commercial source. The other 40% of the simulant was a high calcium (An100), vesicular glass that Washington Mills made specifically for the simulant. Fabrication and quality control processes for both the glass and the simulant are described. Importantly, most of the graphs and tables presented herein provide values for both the new simulant and data for the older NASA mare simulant, JSC-1A. Finally, we discussed the current limitations of NUW-LT-5M and most other lunar regolith simulants to replicate the lunar material.

lunar regolith simulant↗
NASA NTRS1993

Two-directional skin friction measurement utilizing a compact internally mounted thin-liquid-film skin friction meter

A new, compact oil film skin friction meter capable of measuring skin friction in two directions has been designed and constructed. The instrument allows the thin liquid film technique to now be applied in flight and in a wider variety of laboratory conditions. The instrument was tested by comparing measurements with those given by a floating element gage in laminar, transitional, and turbulent boundary layers with zero pressure gradient. Both instruments agreed satisfactorily with each other and with the expected curves for the laminar and turbulent boundary layers. Significant differences were at first seen between the oil film meter and two floating element gages in the case of a favorable pressure gradient, but when a correction is applied to account for the normal force acting on the pendulum-type gage, the three instruents are much closer. The directional sensitivity of the oil film gage is also demonstrated.

Seto, Jeffrey A.↗
NASA NTRS1996

Effect of Transpiration Injection on Skin Friction in an Internal Supersonic Flow

An experimental program was conducted at NASA Langley Research Center that included development and evaluation of an operational facility for wall drag measurement of potential scramjet fuel injection or wall cooling configurations. The facility consisted of a supersonic tunnel, with one wall composed of a series of interchangeable aluminum plates attached to an air bearing suspension system. The system was equipped with load cells that measured drag forces of 115 psia (793 kPa). This flow field contained a train of weak, unsteady, reflecting shock waves that were produced in the Mach 2 nozzle flows, the effect of reflecting shocks (which are to be expected in scramjet combustors) in internal flows has not previously been documented.

Castiglone, L. A.↗
NASA NTRS1999

Aircraft and Ground Vehicle Winter Runway Friction Assessment

Some background information is given together with the scope and objectives of a 5-year, Joint Winter Runway Friction Measurement Program between the National Aeronautics & Space Administration (NASA), Transport Canada (TC), and the Federal Aviation Administration (FAA). Participants recently completed the fourth winter season of testing. The primary objective of this effort is to perform instrumented aircraft and ground vehicle tests aimed at identifying a common number that all the different ground vehicle devices would report. This number, denoted the International Runway Friction Index (IRFI) will be related to all types of aircraft stopping performance. The range of test equipment, the test sites, test results and accomplishments, the extent of the substantial friction database compiled, and future test plans will be described. Several related studies have also been implemented including the effects of contaminant type on aircraft impingement drag and the effectiveness of various runway and aircraft de-icing chemical types and application rates. New equipment and techniques to measure surface frictional properties are also described. The status of an international friction index calibration device for use in ensuring accuracy of ground vehicle friction measurements will also be discussed. NASA considers the success of this joint program critical in terms of ensuring adequate ground handling capability in adverse weather conditions for future aircraft being designed and developed as well as improving the safety of current aircraft ground operations.

Yager, Thomas J.↗
NASA NTRS1994

Analytical skin friction and heat transfer formula for compressible internal flows

An analytic, closed-form friction formula for turbulent, internal, compressible, fully developed flow was derived by extending the incompressible law-of-the-wall relation to compressible cases. The model is capable of analyzing heat transfer as a function of constant surface temperatures and surface roughness as well as analyzing adiabatic conditions. The formula reduces to Prandtl's law of friction for adiabatic, smooth, axisymmetric flow. In addition, the formula reduces to the Colebrook equation for incompressible, adiabatic, axisymmetric flow with various roughnesses. Comparisons with available experiments show that the model averages roughly 12.5 percent error for adiabatic flow and 18.5 percent error for flow involving heat transfer.

Dechant, Lawrence J.↗
NASA NTRS1999

The Joint Winter Runway Friction Measurement Program

This paper provides background information, scope and objectives of a 5-year, Joint National Aeronautics & Space Administration (NASA)/Transport Canada (TC)/Federal Aviation Administration (FAA) Winter Runway Friction Measurement Program which has just completed its fourth winter season of testing. The test equipment, test sites, test results and accomplishments, the extent of the friction database compiled and future plans are described. The primary objective of this effort is to perform instrumented aircraft and ground vehicle tests aimed at identifying a "common number" that ground vehicle devices would report. This number denoted the International Runway Friction Index (IRFI) will be related to aircraft stopping performance. Several related studies are described including the effects of contaminant type on aircraft impingement drag and the effectiveness of various runway/aircraft chemical types and application rates. NASA considers the success of this program critical to insure adequate ground performance capability in adverse weather conditions for future aircraft as well as improving the safety of current aircraft ground operations.

Yager, Thomas J.↗