Search NASA⌕ Search

SEARCH · Search NASA

Results for “LEU”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Calculation of Spent Fuel Pool Time-to-Boil using Polaris/ORIGAMI [Slides]

The goal of this experiment was to calculate time-to-boil (TTB) for a Spent Fuel Pool (SFP). TTB is important for SFP management that represents the amount of time available to address loss of forced cooling. Researchers calculated and compared TTB for two cases using SCALE: SFP containing representative LEU fuel (≤ 5 wt %) and SFP containing representative LEU+ fuel (5 – 8 wt %). There were approximately 2300 fuel assemblies in the SFP for each case. Researchers concluded that the impact of LEU+ core on time-to-boil is very small. At such low cooling times, the impact of increased decay heat is not significant. Decay heat of SFP assemblies is small compared to discharge core decay heat.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Comparative study on the novel umami‐active peptides of the whole soybeans and the defatted soybeans fermented soy sauce

Abstract BACKGROUND Two kinds of soy sauce produced via fermentation of the whole soybeans and the defatted soybeans (soy sauce termed ‘SSS’ and ‘SSD’, respectively) were subjected to the treatment using aqueous ethanol solutions with high concentrations. Then tasty peptides were separated from SSS and SSD by sensory guided fractionation, using macroporous resin and reverse‐phase high‐performance liquid chromatography (RP‐HPLC), and identified by ultra‐performance liquid chromatography quadrupole time‐of‐flight tandem mass spectrometry (UPLC‐Q‐TOF‐MS/MS). Results The result showed that umami‐active fractions and ≤ 3 kDa peptides were mainly concentrated in the supernatants resulted from the treatment with 60% ethanol and the precipitates resulted from the treatment with 80% ethanol. The contents of ammonia nitrogen, non‐salt solids, bitter amino acids, amino acids in peptides and the proportion of ≤ 3 kDa peptides in SSS were higher than those in SSD. Sixteen and fourteen tasty peptides were separated from SSS and SSD, among them five dipeptides (γ‐Glu‐Glu, Glu‐Glu, γ‐Glu‐Cys, γ‐Glu‐Leu, Glu‐Leu and Ile‐Glu) with a glutamic acid residue were identified both in SSS and SSD, which have been reported as umami/kokumi‐active peptides in soy sauce. Several peptides identified from SSS (Thr‐Gly‐Cys, Gly‐Leu‐Glu, Val‐Glu‐Ala‐Leu and Gly‐Gly‐Gly‐Glu) and SSD (Asp‐Arg, Asp‐Ala‐Glu, Glu‐Val‐Cys and Gly‐Gly‐Gly‐Glu) are tasty and/or umami‐active peptides but have not been reported as tasty peptides in the past. Conclusion Most of the peptides separated from SSD and SSS could impart an umami‐enhancing effect on soy sauce, and the marginally more kokumi and bitterness hydrophobic peptides were found in SSS than SSD. © 2020 Society of Chemical Industry

Zhu, Xiping↗
DOE OSTI2020

Partially-Reflected Water-Moderated Square-Pitched U(6.90)O 2 Fuel Rod Lattices with 0.52 Fuel to Water Volume Ratio (0.855 CM Pitch)

The US Department of Energy (DOE) Nuclear Energy Research Initiative funded the design and construction of the Seven Percent Critical Experiment (7uPCX) at Sandia National Laboratories. The start-up of the experiment facility and the execution of the experiments described here were funded by the DOE Nuclear Criticality Safety Program. The 7uPCX is designed to investigate critical systems with fuel for light water reactors in the enrichment range above 5 % 235 U. The 7uPCX assembly is a water-moderated and -reflected array of aluminum-clad square-pitched U(6.90 %)0 2 fuel rods. Other critical experiments performed in the 7uPCX assembly are documented in LEU-COMP-THERM-078, LEU-COMP-THERM-080, LEU-COMP-THERM-096, and LEU-COMP-THERM-097.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

University of Missouri Research Reactor (MURR) Design Demonstration Element End Fitting Structural Rigidity Analysis

The primary objective of this work is to assess the extent to which the stiffness (measured by means of maximum displacement) of the end fittings in the DDE contributes to the stiffness of the entire element, and how it compares to the equivalent stiffness of the end fittings in the LEU element. Structural analysis of both the LEU element and the DDE were performed using COMSOL 5.3a finite element software. Supporting combs are used on the leading and trailing edges of fuel plates for both the LEU element and the DDE. Therefore, simulations with and without combs are performed as two bounding boundary conditions on the leading edge of the fuel plates. Three types of loads are analyzed in this work: the hydraulic load due to the channel flow disparity-induced pressure differential, the thermal load due to the thermal expansion of the fuel plates, and a point load equal in magnitude to the LEU element’s weight.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Assessment of Core Physics Characteristics of Extended Enrichment and Higher Burnup LWR Fuels using the Polaris/PARCS Two-Step Approach (Vol. 2: BWR Fuel)

Nuclear fuel vendors and utilities are currently investigating changes to fuel contents and fuel designs for more economical and safer reactor operations. Extending cycle lengths beyond 18-month cycles for pressurized water reactors (PWRs) and 24-month cycles for boiling water reactors (BWRs) requires extending fuel enrichments beyond the current 5 wt % 235U limit. Therefore, low-enriched uranium plus (LEU+) fuel is expected to be used in current light-water reactor fleets in the near term. LEU+ is a subset of high-assay low-enriched uranium (HALEU) and is a term to describe fuel enrichments above 5% up to 10%. A series of studies were conducted at Oak Ridge National Laboratory (ORNL) to compare low-enriched uranium (LEU) with LEU+ fuel with respect to isotopic fuel content, lattice parameters, and core physics to identify any challenges in operation, storage, and transportation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1997

Mitochondrial gene arrangement of the horseshoe crab Limulus polyphemus L.: conservation of major features among arthropod classes

Numerous complete mitochondrial DNA sequences have been determined for species within two arthropod groups, insects and crustaceans, but there are none for a third, the chelicerates. Most mitochondrial gene arrangements reported for crustaceans and insect species are identical or nearly identical to that of Drosophila yakuba. Sequences across 36 of the gene boundaries in the mitochondrial DNA (mtDNA) of a representative chelicerate. Limulus polyphemus L., also reveal an arrangement like that of Drosophila yakuba. Only the position of the tRNA(LEU)(UUR) gene differs; in Limulus it is between the genes for tRNA(LEU)(CUN) and ND1. This positioning is also found in onychophorans, mollusks, and annelids, but not in insects and crustaceans, and indicates that tRNA(LEU)(CUN)-tRNA(LEU)(UUR)-ND1 was the ancestral gene arrangement for these groups, as suggested earlier. There are no differences in the relative arrangements of protein-coding and ribosomal RNA genes between Limulus and Drosophila, and none have been observed within arthropods. The high degree of similarity of mitochondrial gene arrangements within arthropods is striking, since some taxa last shared a common ancestor before the Cambrian, and contrasts with the extensive mtDNA rearrangements occasionally observed within some other metazoan phyla (e.g., mollusks and nematodes).

Non-NASA Center↗
DOE OSTI2022

The international research reactor conversion effort and its contribution to the validation of reactor physics and thermal-hydraulics codes

Full text of publication follows. With about 200 reactors in operation, civilian Research and Test Reactors (RTRs) represent approximately a third of the global nuclear fleet. RTRs make use of core designs that are drastically different from commercial power plants to perform a wide variety of non-power applications that greatly benefit society. Because they often rely on high neutron fluxes, RTRs are designed with relatively compact cores and as a result, prior to the 1980's, were often deployed using Highly Enriched Uranium fuel (HEU, {sup 235}U/U = 20 wt. %). Due to proliferation concerns, the international community aims at eliminating the use of HEU in civilian facilities and favor instead the use of Low Enriched Uranium fuel (LEU, {sup 235}U/U < 20 wt. %). A program to support conversion of the world's RTRs to LEU fuel has been initiated in 1978 by the U.S. Department of Energy (DOE). This program is still alive today and has achieved more than 103 conversion metrics. Today, the program focuses heavily on the conversion of so-called high-performance RTRs, which are far more challenging than previous conversions as they require new fuel element designs and the use of new, higher density LEU fuel forms. Development and qualification of new LEU fuel elements is ongoing and requires extensive engineering analysis and testing. Both activities require the development and validation of codes and methods for reactor physics, thermal-hydraulics, and multi-physics, which in turn rely on experiments performed in RTRs or other experimental facilities. This talk will present the collection of RTR experimental data and benchmark analyses from the international conversion program that contribute to the validation of computer codes and methods.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Microstructurally validated stable and predictable swelling in low-enriched uranium monolithic U-10Mo fuel mini-plates

Qualification of the low-enriched uranium (LEU) monolithic U-10 wt%Mo (U-10Mo) plate-type fuel system requires a demonstration of a stable and predictable fuel swelling behavior over the anticipated operating conditions of the United States high-performance research reactors (USHPRRs) selected for conversion to LEU operation. This will allow each reactor to develop appropriate safety margins that will retain fuel element lifetime coolability. Additionally, the fuel system must maintain performance attributes when fabricated at a commercial scale. The Mini-plate 1 experiment represents the first irradiation test of commercially fabricated miniaturized monolithic LEU U-10Mo fuel plates. Here, the swelling behavior within this experiment was compared against that of historical fuel developmental tests to reveal that the commercially fabricated fuel performed within the current recommended U-10Mo swelling model's predictions. Additionally, the fuel microstructural evolution was evaluated to link initial conditions to subtle variations detected in the swelling response, providing validation and confidence that the fuel system is robust.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Fuel cycle depletion validation and code-to-code verification studies for High Flux Isotope Reactor highly and low-enriched uranium fuel designs

Here, this paper documents fuel cycle depletion validation and code-to-code verification studies for the High Flux Isotope Reactor (HFIR) highly enriched uranium (HEU) and proposed low-enriched uranium (LEU) fuel designs. In support of HFIR’s world-leading performance, transport and depletion simulations are performed to ensure safe operations, design and qualify irradiation experiments, enhance core components and irradiation facilities, and design and characterize LEU fuel designs. Identifying well-validated, computationally efficient codes is required for the success of these efforts. The HFIR Controller, Shift, and VESTA codes were deployed to simulate HEU uranium–oxide dispersion fuel cycles at 85, 95, and 100 MW operations, as well as LEU fuel cycles operating at 95 MW with uranium–silicide dispersion and uranium–molybdenum monolithic alloy fuel forms. Excellent agreement between the codes and with experimentally obtained 235 U enrichment distributions provides increased confidence in the ability of these codes to model and simulate HFIR’s unique core design.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Multimodal analysis and characterization of the boehmite layer formed on AA6061 before and after alkaline etching

Low-enriched uranium (LEU) alloyed with 10% Mo (U-10Mo) is being considered as a promising alternative to oxide-based dispersion fuel with high-enriched uranium for use in research reactors. The configuration of this proposed LEU monolithic LEU fuel plate consists of a U-10Mo plate-type fuel foil with a 25 µm zirconium interlayer barrier clad with an aluminum alloy (AA6061). In certain research reactors, the clad AA6061 is coated with a boehmite layer to prevent corrosion. The boehmite layer has a high-pH passivation range, which makes it resistant to oxidation. Boehmite is usually formed on the AA6061 surface by autoclave processing. Before the boehmite layer is added, the surface of the AA6061 is cleaned using techniques such as polishing and wet etching. In this study, we use multimodal analysis to examine how pretreatment of AA6061 using polishing followed by alkaline etching affects the chemical composition of the boehmite layer. X-ray photoelectron microscopy (XPS), transmission electron microscopy (TEM), and x-ray diffraction (XRD) were used to study the chemical changes in the boehmite layer caused by alkaline etching pretreatment. XPS provides quantitative analysis for the Al:O ratio as well as oxidation states present on the surface, which suggests slight oxidation of the boehmite surface after alkaline etching of the AA6061 surface. We further explored this suggested oxidation of the boehmite surface using high-resolution transmission electron microscopy with selected area electron diffraction (SAED) and grazing incidence x-ray diffraction (GI-XRD), which suggested only a small amount of aluminum oxide at the surface. The multimodal analysis and imaging yielded new insights for optimizing boehmite growth on AA6061 for research reactors.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Startup Test Plan and Predictions for Highly Enriched Uranium to Low-Enriched Uranium Fuel Conversion at the University of Missouri Research Reactor

Nonpower reactors licensed by the U.S. Nuclear Regulatory Commission require a startup test plan as part of any facility modification to verify operability prior to resumption of operations. In order to support conversion of the University of Missouri Research Reactor from the use of highly enriched uranium to low-enriched uranium (LEU) fuel, a startup test plan has been devised to measure certain reactor physics parameters for the initial all-fresh LEU core licensing documentation that will be submitted. These parameters include the approach to critical, primary coolant void coefficient of reactivity, flux trap void coefficient of reactivity, determination of flux trap sample reactivity worth, radial and axial thermal neutron flux mapping, control blade worth calibration, primary and pool coolant temperature coefficient of reactivity, and flux mapping of experimental positions. Here, predictions for these parameters made using the Monte Carlo N-Particle Version 5 (MCNP5) radiation transport code are reported. These predictions will support the startup tests by providing a baseline set of expectations and additional insight into the performance of the LEU core.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Design Optimization of A generic Fissile Solution for Mo99 production using Electron Beam-based Neutron Generator using MCNP+CFD

Molybdenum-99 ( 99 Mo) is a medical isotope used in 80% of all medical imaging procedures today. However, 99 Mo is not directly administered to patients for imaging; its decay product, technetium-99m ( 99 mTc), is a metastable isotope with a half-life of ~6 hours. Such a short half-life does not allow for production, separation, and application to a patient before decaying further. Therefore, the solution is to produce the precursor to 99 mTc, 99 Mo. 99 Mo has a half-life of 66 hours, long enough to produce the material and send it to the desired location before it fully decays. Under National Nuclear Security Administration’s (NNSA) highly enriched uranium (HEU) minimization mission, the Material Management and Minimization (M3) office leads the Molybdenum-99 (Mo-99) program. A major goal of the Mo-99 program is to develop methods of producing 99 Mo using low enriched uranium (LEU) opposed to the traditionally used HEU domestically in the U.S. Internationally, LEU is the new standard for use in research reactors and isotope production facility. In this study, we introduce a generic fissile solution system for 99 Mo production facility meeting the design requirement of 1) LEU usage as fissile material and 2) subcritical fissile system coupled with a horizontal electron beam (E-beam) accelerator. The focus of this research is to optimize a fissile solution configuration for maximum 99 Mo production yield using MCNP model, and ultimately implement the optimized design with computational fluid dynamics (CFD) model to understand thermal hydraulic behavior and solution convection characteristic. The report consists of two parts: 1) isotope yield calculation and criticality analysis with a wide range of parametric test matrix, and 2) thermal hydraulic analysis for solution mixing and cooling assessment.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2021

Nuclear Data and Cross Section Testing Using ENDF/B-VIII.0

With the release of the Evaluated Nuclear Data File (ENDF)/B-VIII.0 library, nuclear criticality safety practitioners and engineers have access to the latest cross section sets available for their analyses. However, these cross sections must be rigorously tested and validated to ensure that the nuclear data are responsive to the needs of the individuals responsible for developing, implementing, and maintaining computational tools for criticality safety applications. Thus, the ENDF/B-VIII.0 library is tested and validated with a large collection of experiments that were vetted by the International Criticality Safety Benchmark Evaluation Project and made available in the International Handbook of Evaluated Criticality Safety Benchmark Experiments. A selection of benchmark experiments for use within the criticality safety community were prepared and reviewed within the Verified, Archived Library of Inputs and Data (VALID), which is maintained by the Nuclear Energy and Fuel Cycle Division at Oak Ridge National Laboratory. The performance of the ENDF/B-VIII.0 library is assessed by using VALID models of benchmark experiments with the beta 12 version of SCALE 6.3 KENO V.a and KENO-VI Monte Carlo codes. The performance is compared with the results obtained from with the ENDF/B-VII.1 library. This report considers multigroup (MG) and continuous energy (CE) formats of the ENDF/B-VIII.0 and -VII.1 libraries. The benchmark experiments within VALID that validate the ENDF/B-VIII.0 library cover 15 broad system categories by using a range of fissile materials, uranium enrichments, plutonium isotopic vectors, and mixed uranium/plutonium systems. These forms are represented as metals, solutions, or various arrays of rods or plates that cover a variety of neutron energy spectra: thermal, fast, mixed, and intermediate. Over 600 cases were considered for use with the KENO V.a and KENO-VI codes with the ENDF/B-VIII.0 library. The results of the Monte Carlo comparison of ENDF/B-VIII.0 to ENDF/B-VII.1 with both KENO V.a and KENO-VI indicate that there is a less than 0.53% Δk difference between the bias of calculated k eff from the expected values. The CE ENDF/B-VIII.0 library results in smaller magnitude biases than the ENDF/B-VII.1 data for HEU-MET-FAST, HEU-SOL-THERM, IEU-MET-FAST, LEU-SOL-THERM, PU-SOL-THERM, and U233-MET-FAST systems, while the MG results yielded smaller magnitude biases for HEU-MET-FAST, HEU-SOL-THERM, IEU-MET-FAST, LEU-COMP-THERM, LEU-SOL THERM, MIX-COMP-FAST, and U233-MET-FAST systems. Most notable are the adjustments to the plutonium and 233 U cross section data, which has resulted in noticeably lower biases in the ENDF/B VIII.0 results for the mixed, plutonium, and 233 U systems. Results of the sensitivity data file comparison generated from TSUNAMI-3D for selected VALID cases for the ENDF/B-VIII.0 library indicate a very high level of agreement with correlation coefficients of the effect of nuclear data uncertainty on k eff (the c k integral parameter) all above 0.99. This indicates that cases with the ENDF/B-VIII.0 library would see very similar responses to any nuclear data errors or change as those with the ENDF/B-VII.1 library.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Irradiation Thermo-Mechanical Modeling and Analysis of University of Missouri Research Reactor HEU Fuel Plates

The University of Missouri Research Reactor (MURR) located in Columbia, Missouri is one of six U.S. High Performance Research Reactors (USHPRR), including one critical facility, that is actively collaborating with U. S. Department of Energy (DOE) National Nuclear Security Administration (NNSA) Material Management and Minimization (M3) Office of Reactor Conversion and Uranium Supply to convert from the use of highly enriched uranium (HEU; $\geqslant$ 20 wt% U-235) to low-enriched uranium (LEU; <20 wt% U-235) fuel. A new type of very high-density LEU fuel based on an alloy of uranium and 10 wt% molybdenum (U-10Mo) is expected to allow the conversion to LEU of MURR, as well as four other USHPRR.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

HFIR High Power HEU Neutronics Analyses

Department of Energy National Nuclear Security Administration Office of Material Management and Minimization’s mission includes the conversion of civilian research reactors from highly enriched uranium (HEU) to low-enriched uranium (LEU) fuel. Analyses have shown that the Oak Ridge National Laboratory High Flux Isotope Reactor (HFIR) will need to operate at 95 MW for the LEU silicide dispersion fuel designs to match key performance metrics obtained with HEU fuel at 85 MW. To prove safe operation of HFIR after installation of plant modifications to increase power, a high power HEU test cycle was proposed. Neutronics model updates and reactor physics analyses are performed to support the development of safety design reports for the high power (HP) HEU test cycle. Reactor physics metrics evaluated herein include fuel depletion, actinide production, cycle length, fission rate density distributions, axial power peaking factors, and reactor kinetic parameters. These reactor physics analyses support the development of future LEU safety design reports by providing key input for future HP HEU HFIR thermal hydraulics and reactor transient safety analyses.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1971

Mechanism of pulmonary conversion of angiotensin I to angiotensin II in the dog.

The conversion mechanism was studied in vivo in the pulmonary circulation of the intact anesthetized dog and in vitro in plasma by using L-Leu-angiotensin I, D-Leu-angiotensin I, and des-Leu-angiotensin I which had been synthesized by the solid-phase technique. The results obtained indicate that pulmonary conversion in vivo and plasma conversion in vitro occur via a dipeptidylcarboxypeptidase and that a D-amino acid at the C-terminus prevents conversion.

Oparil, S.↗
NASA NTRS2018

Space Technology Mission Directorate: Game Changing Development Program: Nuclear Thermal Propulsion

Nuclear Thermal Propulsion (NTP) can help enable detailed exploration of the solar system, extensive development and utilization of cis-lunar space, and robust human Mars architectures. To improve affordability and viability, NTP systems that utilize low-enriched uranium (LEU) instead of highly enriched uranium (HEU) are being devised. Advanced fuel manufacturing techniques will help enable the use of LEU in certain fission systems previously thought to require HEU. The current LEU NTP baseline engine relies on a fission reactor containing fuel elements made of uranium nitride and refractory metals.

testing and performance↗
DOE OSTI2022

ANS Winter 2022: ATF-2C Physics Safety and Scoping Analysis

ATF-2C comprises four tiers with six rodlets each. The experiment test train (TT) is situated in Loop 2A in the center flux trap (CFT) of the ATR, in which typical pressurized water reactor (PWR) conditions shall be approximated. Tier 1 (bottom) of the TT tests Framatome silicon carbide (SiC) cladding, containing molybdenum heater rods. Low-enriched uranium (LEU) Framatome rodlets with chrome-coated M5 cladding have been modeled in their place for the physics safety analysis to allow the substitution of this tier with fuel if needed. Tier 2 tests LEU Framatome rodlets with M5 cladding, which had irradiated in ATR in prior ATF experiments. Tier 3 tests General Atomics SiC composite cladding, also containing molybdenum heater rods. Tier 4/5/6 (top) tests the Japan Atomic Energy Agency (JAEA)/Mitsubishi Heavy Industries (MHI) fueled rodlets. This upper tier tests LEU rodlets with chrome-coated MDA cladding—several with temperature or pressure instrumentation. To flatten the axial power profile, lower portion of Tier 4/5/6 is surrounded by a hafnium (Hf) shroud, and the bottom two UO2 pellets are of natural enrichment. The ATF-2C TT is to be irradiated in the CFT of ATR (Fig. 1) for three or four 60-day cycles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗