Search NASA⌕ Search

SEARCH · Search NASA

Results for “LOADS - PLATES, RECTANGULAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Comparison of calculated and measured model rotor loading and wake geometry

The calculated blade bound circulation and wake geometry are compared with measured results for a model helicopter rotor in hover and forward flight. Hover results are presented for rectangular tip and ogee tip planform blades. The correlation is quite good when the measured wake geometry characteristics are used in the analysis. Available prescribed wake geometry models are found to give fair predictions of the loading, but they do not produce a reasonable prediction of the induced power. Forward flight results are presented for twisted and untwisted blades. Fair correlation between measurements and calculations is found for the bound circulation distribution on the advancing side. The tip vortex geometry in the vicinity of the advancing blade in forward flight was predicted well by the free wake calculation used, although the wake geometry did not have a significant influence on the calculated loading and performance for the cases considered.

Johnson, W.↗
NASA NTRS1990

External nozzle flap dynamic load measurements on F-15 S/MTD model

Dynamic pressure loads were obtained on 1/12 scale models of the F-15B production aircraft and the F-15 S/MTD experimental aircraft with rectangular nozzles and canards. Flight Mach numbers from 0.51 to 1.20 were studied for aircraft angles of attack from 0 to 10 deg and nozzle pressure ratios from 1.00 to 5.09. The results show that dynamic levels are lower in the internozzle region of twin rectangular nozzles than are levels found with twin axisymmetric nozzles. At other locations, the levels associated with both geometries are of the same order of magnitude when normalized by aircraft dynamic Q. At Mach number of 0.51, the loads spectrum is dominated by plume shock noise processes for both geometries. Above Mach 0.51, this mechanism is associated with either vortex bursting from a forward location or turbulent boundary layer separation over the nozzle external flaps. At supersonic speeds both geometries show significantly decreased load levels.

Seiner, John M.↗
NASA NTRS1942

A method for determining the camber and twist of a surface to support a given distribution of lift

A graphical method is described for finding the shape (camber and twist) of an airfoil having an arbitrary distribution of lift. The method consists in replacing the lifting surface and its wake with an equivalent arrangement of vortices and in finding the associated vertical velocities. By a division of the vortex pattern into circular strips concentric about the downwash point instead of into the usual rectangular strips, the lifting surface is reduced for each downwash point to an equivalent loaded line for which the induced velocity is readily computed. The ratio of the vertical velocity to the stream velocity is the slope of the surface in the free-stream direction. As an illustration, the shape of the wing consistent with the pressure distribution derived from the two-dimensional theories is found for two wings: a straight elliptical wing and one with 30 degree sweepback. Application of the method to solve the reverse problem - finding the lift distribution over a given surface - is briefly discussed.

Cohen, Doris↗
NASA NTRS1988

Strain-Energy-Release Rates In Delamination

Q3DG computer program developed to perform quasi-three-dimensional stress analysis of composite laminates containing delaminations. Calculates strain-energy-release rates for long, rectangular composite laminates containing delaminations and subjected to any combination of mechanical, thermal, and hygroscopic loading. Written in FORTRAN V.

Raju, I. S.↗
NASA NTRS1990

On the numerical solution of the dynamically loaded hydrodynamic lubrication of the point contact problem

The transient analysis of hydrodynamic lubrication of a point-contact is presented. A body-fitted coordinate system is introduced to transform the physical domain to a rectangular computational domain, enabling the use of the Newton-Raphson method for determining pressures and locating the cavitation boundary, where the Reynolds boundary condition is specified. In order to obtain the transient solution, an explicit Euler method is used to effect a time march. The transient dynamic load is a sinusoidal function of time with frequency, fractional loading, and mean load as parameters. Results include the variation of the minimum film thickness and phase-lag with time as functions of excitation frequency. The results are compared with the analytic solution to the transient step bearing problem with the same dynamic loading function. The similarities of the results suggest an approximate model of the point contact minimum film thickness solution.

Lim, Sang G.↗
NASA NTRS1984

Aerothermal loads analysis for high speed flow over a quilted surface configuration

Attention is given to hypersonic laminar flow over a quilted surface configuration that simulates an array of Space Shuttle Thermal Protection System panels bowed in a spherical shape as a result of thermal gradient through the panel thickness. Pressure and heating loads to the surface are determined. The flow field over the configuration was mathematically modeled by means of time-dependent, three-dimensional conservation of mass, momentum, and energy equations. A boundary mapping technique was then used to obtain a rectangular, parallel piped computational domain, and an explicit MacCormack (1972) explicit time-split predictor corrector finite difference algorithm was used to obtain steady state solutions. Total integrated heating loads vary linearly with bowed height when this value does not exceed the local boundary layer thickness.

Olsen, G. C.↗
NASA NTRS1984

Aerothermal loads analysis for high speed flow over a quilted surface configuration

Attention is given to hypersonic laminar flow over a quilted surface configuration that simulates an array of Space Shuttle Thermal Protection System panels bowed in a spherical shape as a result of thermal gradients through the panel thickness. Pressure and heating loads to the surface are determined. The flow field over the configuration was mathematically modeled by means of time-dependent, three-dimensional conservation of mass, momentum, and energy equations. A boundary mapping technique was then used to obtain a rectangular, parallelepiped computational domain, and an explicit MacCormack (1972) explicit time-split predictor-corrector finite difference algorithm was used to obtain steady state solutions. Total integrated heating loads vary linearly with bowed height when this value does not exceed the local boundary layer thickness.

Olsen, G. C.↗
NASA NTRS1990

A test fixture for measuring high-temperature hypersonic-engine seal performance

A test fixture for measuring the performance of several high temperature engine seal concepts was installed at the NASA Lewis Research Center. The test fixture was developed to evaluate seal concepts under development for advanced hypersonic engines such as those being considered for the National Aerospace Plane. The fixture can measure static seal leakage performance from room temperature up to 1500 F and air pressure differentials up to 100 psi. Performance of the seals can be measured while sealing against flat or engine simulated distorted walls, where distortions can be as large as 0.150 in. in only an 18 in. span. The fixture is designed to evaluate seals 3 feet long, a typical engine panel length. The seal channel can be configured to test square, circular, or rectangular seals that are nominally 0.5 in. high. The sensitivity of leakage performance to lateral or axial loading can also be measured using specially designed high temperature lateral and axial bellows preload systems. Leakage data for a candidate ceramic wafer engine seal is provided by way of example to demonstrate the test fixture's capabilities.

Steinetz, Bruce M.↗
NASA NTRS1954

Experimental Stress Analysis of Stiffened Cylinders with Cutouts : Shear Load

A cylindrical semimonocoque shell of circular cross section was mounted as a cantilever and loaded by a direct shear at the tip. The cylinder was tested with no cutout, with a rectangular cutout on the tension side, and with the cutout centered on the neutral axis on one side of the cylinder. The cutout was successively enlarged through six sizes varying from 30 degrees to 130 degrees in circumference and from 1 and 2 bays in length. Strain measurements were made with resistance-type wire strain gages near the cutout on the stringers, the skin, and the rings for each case, and the stresses obtained are presented in tables. (author)

Rosecrans, Richard↗
NASA NTRS1960

Experimental and Theoretical Study of a Rectangular Wing in a Vortical Wake at Low Speed

A systematic study has been made, experimentally and theoretically, of the effects of a vortical wake on the aerodynamic characteristics of a rectangular wing at subsonic speed. The vortex generator and wing were mounted on a reflection plane to avoid body-wing interference. Vortex position, relative to the wing, was varied both in the spanwise direction and normal to the wing. Angle of attack of the wing was varied from -40 to +60. Both chordwise and spanwise pressure distributions were obtained with the wing in uniform and vortical flow fields. Stream surveys were made to determine the flow characteristics in the vortical wake. The vortex-induced lift was calculated by several theoretical methods including strip theory, reverse-flow theory, and reverse-flow theory including a finite vortex core. In addition, the Prandtl lifting-line theory and the Weissinger theory were used to calculate the spanwise distribution of vortex-induced loads. With reverse-flow theory, predictions of the interference lift were generally good, and with Weissinger's theory the agreement between the theoretical spanwise variation of induced load and the experimental variation was good. Results of the stream survey show that the vortex generated by a lifting surface of rectangular plan form tends to trail back streamwise from the tip and does not approach the theoretical location, or centroid of circulation, given by theory. This discrepancy introduced errors in the prediction of vortex interference, especially when the vortex core passed immediately outboard of the wing tip. The wake produced by the vortex generator in these tests was not fully rolled up into a circular vortex, and so lacked symmetry in the vertical direction of the transverse plane. It was found that the direction of circulation affected the induced loads on the wing either when the wing was at angle of attack or when the vortex was some distance away from the plane of the wing.

Smith, Willard G.↗
NASA NTRS1973

Finite element stress analysis of polymers at high strains

A numerical analysis is presented for the problem of a flat rectangular rubber membrane with a circular rigid inclusion undergoing high strains due to the action of an axial load. The neo-hookean constitutive equations are introduced into the general purpose TITUS program by means of equivalent hookean constants and initial strains. The convergence is achieved after a few iterations. The method is not limited to any specific program. The results are in good agreement with those of a company sponsored photoelastic stress analysis. The theoretical and experimental deformed shapes also agree very closely with one another. For high strains it is demonstrated that using the conventional HOOKE law the stress concentration factor obtained is unreliable in the case of rubberlike material.

Durand, M.↗
NASA NTRS1990

Estimate of loads during wing-vortex interactions by Munk's transverse-flow method

The inviscid, incompressible interaction of a wing with a vortex is studied by use of Munk's transverse-flow method. The method assumes that the loading on the wing is such that the local circulatory flow of the vortex is turned so that the wing and its vortex wake act as a barrier to the flow. This permits the analysis to be carried out by mapping the transverse flowfield into the flow about a circle to find the vorticity distribution in the wake. Closed-form expressions are then derived for the bound circulation in the wind and for the lift and rolling moment induced by the vortex on the encountering wing. Comparisons of the loads predicted by these relationships with those of vortex-lattice theory for a flat wing of a rectangular planform indicate that they accurately represent the various parameters when the aspect ratio of the encountering wing is less than about two. When flat rectangular wings of higher aspect ratios are considered, some sort of correction is needed. Examples are then presented to illustrate some applications of the results.

Rossow, Vernon J.↗
NASA NTRS1991

Experimental study of an independently deflected wingtip mounted on a semispan wing

The results of a subsonic wind tunnel test of a semispan wing with an independently deflected tip surface are presented and analyzed. The tip surface was deflected about the quarter chord of the rectangular wing and accounted for 17 percent of the wing semispan. The test was conducted to measure the loads on the tip surface and to investigate the nature of aerodynamic interference effects between the wing and the deflected tip. Results are presented for two swept tip surfaces of similar planform but different airfoil distributions. The report contains plots of tip lift, drag, and pitching moment for various Reynolds numbers and tip deflection angles with respect to the inboard wing. Oil flow visualization photographs for a typical Reynolds number are also included. Important aerodynamic parameters such as lift and pitching moment slopes and tip aerodynamic center location are tabulated. A discussion is presented on the relationship between tip experimental data acquired in a steady flow and the prediction of unsteady tip motion at fixed wing angles of attack.

Martin, D. M.↗
NASA NTRS1993

Method of continuously determining crack length

The determination of crack lengths in an accurate and straight forward manner is very useful in studying and preventing load created flaws and cracks. A crack length sensor according to the present invention is fabricated in a rectangular or other geometrical form from a conductive powder impregnated polymer material. The long edges of the sensor are silver painted on both sides and the sensor is then bonded to a test specimen via an adhesive having sufficient thickness to also serve as an insulator. A lead wire is connected to each of the two outwardly facing silver painted edges. The resistance across the sensor changes as a function of the crack length in the specimen and sensor. The novel aspect of the present invention includes the use of relatively uncomplicated sensors and instrumentation to effectively measure the length of generated cracks.

Prabhakaran, Ramamurthy↗
NASA NTRS1987

Effect of boundary conditions on dynamic strain response of rectangular panels

An analytical and experimental research program has been initiated at NASA Langley to investigate the strain response of panels under severe thermal and/or acoustic loads. The overall purpose of this program is to develop an analytical model that predicts the stresses and strains leading to sonic fatigue failure in advanced aircraft and aerospace structures. Previous experiments, analyses, and results of this program are reviewed. The analytical modeling refinements and their effects on the calculation of strain are discussed, considering the inclusion of in-plane motion at the panel boundary; the use of the multiterm, multimode Ritz method; and the introduction of transverse stiffness at the boundary. Finally, the findings of the analytical modeling investigation are summarized.

Roussos, Louis A.↗
NASA NTRS1972

Dielectric loaded aperture antennas.

This paper describes a primarily experimental study of the effect of placing dielectric obstacles having various geometries directly upon the aperture of circular and rectangular waveguide antennas. It is found that plexiglas spheres, and in some cases plexiglas cubes, one to four wavelengths in dimension, produce directive patterns with low sidelobes. The measured gain in some cases is 6 dB greater than the gain of an optimum horn having an equal aperture size.

Croswell, W. F.↗
NASA NTRS1988

Stress-intensity factors for corner cracks in rectangular bars

Stress intensity factors are presented for a wide range of quarter-elliptical corner cracks in a rectangular bar. The bars were subjected to remote tension, out-of-plane bending, or in-plane bending loading, and the stress intensity factors were calculated from a three-dimensional finite element analysis using the nodal-force method. For all loadings considered, smaller width bars produce higher normalized stress intensity factors than the larger width bars. For tensile loading, quarter-circular corner cracks give higher stress intensity factors near the free surfaces and lower values in the interior. The results are compared with data in the literature for remote tensile loading.

Raju, I. S.↗