SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Optically driven Q-switches for pulsed lasers proposed, taking place of acousto-optical, magneto-optical, and electro-optical switches. Optical switching beams of proposed Q-switching most likely generated in pulsed diode lasers or light-emitting diodes, outputs of which are amplitude-modulated easily by direct modulation of relatively small input currents. Energy efficiencies exceed those of electrically driven Q-switches.
Measurements and analyses of resources within permanently shadowed craters and along steep embankments on extraterrestrial surfaces pose extreme challenges since astronauts and rovers cannot access them. However, these areas offer the potential for the greatest scientific returns. Researchers at the NASA Langley Research Center (LaRC) invented a deployable wireless micro-spectrometer that can access those challenging areas and deliver telemetry data to a receiver safely outside those extreme environments. The micro-spectrometers are designed for deployment by an astronaut, a rover, or a lander flying overhead. This device can also be installed on rover tires, under the astronaut’s shoes, or on a cane stick. The bullet-like, expendable micro-spectrometer can penetrate into soil to spectrally identify the components of soil, such as water, He-3, or other minerals. The signals from the soil assay data are transmitted to a mother station through a telemetry system. This LaRC developed micro-spectrometer bullet consists of micro-spectrometer optics with an all-imbedded, burst-mode, light-emitting-diode ultraviolet (LED UV) light source, a super-capacitor with control electronics, and telemetry electronics. Prototypes have been fabricated to demonstrate a spectral assay of soil components. Further maturation of this technology would be necessary for demonstrations on the Moon.
Introduction. Light is the major environmental time cue of our endogenous circadian pacemaker. Suboptimal crew circadian entrainment (CCE) is common and associated with acute and chronic medical symptoms. Additionally, fatigue from suboptimal CCE promotes problematic use of sleep medications. The Orion Cabin Lighting System (OCLS) consists of monochromatic light-emitting diode (LED) lamps. However, light is a powerful suppressor of melatonin and it is a disruptor of CCE if used at incorrect times. A commercial off the shelf (COTS) dynamic lighting system (COTS-DLS) is a potential workaround for maintaining CCE.
A particle tracking velocimetry (PTV) system is demonstrated that eliminates the need for expensive lasers and cameras, and encodes the particle tracks with a known intensity variation which allows for high-resolution particle velocity and directionality determination. Using a light-emitting diode (LED) as the light source significantly reduces cost and allows for eye-safe operation, in comparison to traditional laser systems. The intensity variation control is passive, being dictated by the capacitance discharge rate in the LED pulsing circuit. The decay rate can be adjusted with the LED circuit capacitors/resistors, while the duration of the decay can be adjusted with the LED trigger pulse width. Because the intensity decay illumination is controlled by the LED, a single long exposure camera image is used to acquire images of the particle streaks, and there is no need for a more complicated and costly double-pulsing camera. With the intensity coding of the light, a single-camera/ single-LED system can identify particles entering of leaving the illumination plane, but cannot discern the direction toward or away from the camera. By using a two-color system, three-dimensionality of the particle tracks can be determined.
A fiber optic interferometer utilizes a low coherence light emitting diode (LED) laser as a light source which is filtered and driven at two RF frequencies, high and low, that are specific to the initial length of the resonator chamber. A displacement of a reflecting mirror changes the length traveled by the nonreferencing signal. The low frequency light undergoes destructive interference which reduces the average intensity of the wave while the high frequency light undergoes constructive interference which increases the average intensity of the wave. The ratio of these two intensity measurements is proportional to the displacement incurred.
Extensive testing with plants for bioregenerative life support systems has been conducted by NASA for nearly 40 years, both through university grants and work at NASA field centers. During this time, numerous meetings were held to develop strategies and roadmaps for implementing bioregenerative life support systems. Findings from several of these meetings are summarized in this report. In nearly all cases, the recommendations included an active ground-based research program and integration tests with other life support subsystems, followed by eventual spaceflight testing. The most recent roadmap of NASA’s Exploration Life Support Crop Element suggests a sequence of first developing a modular vegetable production unit (VPU) to provide perishable foods to supplement the crew’s diet. A similar system could then be used on the lunar surface, with additional modules added as the lunar outpost expands. Eventually, these modules could be transferred to a dedicated pressurized logistics module (PLM) for crop production. Experience from the lunar tests could then be used to conduct a similar buildup for Mars missions, where in situ food production and bioregeneration would be important for achieving outpost autonomy. To date, most trade studies of bioregenerative life support systems indicate that reducing the costs associated with crop lighting systems are key, and use of light-emitting diodes (LEDs) or direct solar lighting offers promising options. Likewise, sustaining high yields and high harvest index (% edible biomass) will be important for minimizing costs, and this can be achieved by optimizing growth environments and through selecting, breeding, and genetically engineering crops suitable for space environments. Collectively, these strategies and roadmaps suggest that a combined approach of fundamental research, hardware (plant chamber) development, and operational testing is required to achieve reliable bioregenerative life support systems.
Tint-controlled white light is crucial for both illumination systems and display applications. Here, in this study, we demonstrate solution-processed quantum-dot light-emitting diodes (QD-LEDs) featuring a red–green–blue (RGB) QD–poly(methyl methacrylate) (PMMA) composite emissive layer (EML) for tunable white electroluminescence (EL). In this composite EML, PMMA functions as a dispersion matrix that modulates the interdot spacing (d), thereby controlling Förster resonance energy transfer (FRET) between QDs. By adjustment of the PMMA content, the balance of R, G, and B emissions is controlled, enabling systematic and continuous tuning of the EL color from greenish to reddish white at a fixed RGB ratio and constant driving bias. Time-resolved photoluminescence measurements confirm that the variation in the exciton lifetime with the PMMA fraction is the primary factor for tuning the EL color. Notably, nearly pure white EL with CIE coordinates close to (0.33, 0.33) is achieved using a diluted PMMA matrix without significant degradation of the electrical properties. Our results demonstrate d as an independent design parameter for decoupling color tuning from RGB composition and electrical operation, providing a versatile design framework for high-quality white- or tint-controlled QD-LEDs toward advanced solid-state lighting and display technologies.
The stratosphere (10 km to 50 km above sea level) is a unique place on Earth for astrobiological studies of microbes in extreme environments due to the combination of harsh conditions (high ultraviolet radiation, low pressure, desiccation, and low temperatures). Microorganisms in the Stratosphere (MIST) will attempt to characterize the diversity of microbes at these altitudes using a balloon collection device on a meteorological weather balloon. A major challenge of such an aerobiology study is the potential for ground contamination that makes it difficult to distinguish between collected microbes and contaminants. One solution is to use germicidal ultraviolet light emitting diodes (UV LEDs) to sterilize the collection strip. To use this solution, an optimal spatial arrangement of the lights had to be determined to ensure the greatest chance of complete sterilization within the 30 to 60 minute time of balloon ascent. A novel, 3D-printed test stand was developed to experimentally determine viable Bacillus pumilus SAFR-032 spore reduction after exposure to ultraviolet radiation at various times, angles, and distances. Taken together, the experimental simulations suggested that the UV LEDs on the MIST flight hardware should be active for at least 15 minutes and mounted within 4 cm of the illuminated surface at any angle to achieve optimal sterilization. These findings will aid in the production of the balloon collection device to ensure pristine stratospheric microbial samples are collected. Flight hardware capable of in-flight self-sterilization will enable future life detection missions to minimize both forward contamination and false positives.
Vehicle collisions with deer (Odocoileus spp.) cause billions of dollars in damages and injure thousands of drivers every year in the United States, and few mitigation methods have proven effective. However, recent research suggests that vehicle lighting might influence white-tailed deer (Odocoileus virginianus; hereafter, deer) responses to oncoming vehicles. Most new vehicles are manufactured with light emitting diode (LED) headlights which differ in total radiance and wavelength of light emitted compared to the previous industry standard of tungstenhalogen (halogen) headlights. Also, frontal vehicle illumination through rear-facing lighting has shown promise in enhancing deer responses to vehicles, but its effectiveness has not been tested under various headlight conditions (headlight type or intensity). As such, it remains unclear how these aspects of vehicle lighting affect deer responses to an approaching vehicle. We used 23 captive, wild-type deer to investigate how variations in vehicle lighting affect deer responses to an approaching vehicle at night, when most collisions occur. We released deer into a 95 m long, 3 m wide chute and approached them from the opposite end with an electric golf cart outfitted with two versions of stock 2017–2020 Ford Fusion headlights (LED and halogen) and a 51 cm rear-facing lightbar to test how vehicle lighting affected deer avoidance behaviors in an imminent, head-on collision scenario. Each deer received eight lighting treatments consisting of unique combinations of headlight type (LED vs. halogen), light intensity (low vs. high beam), and rear-facing lighting (lightbar off vs. on). We measured deer alert and flight behavior using infrared videography. We found that the halogen, high beam, lightbar off treatment had the greatest probability of evoking an alert response. Furthermore, when the lightbar was off, high beams appeared to increase alert probability for halogen headlights. Also, we found evidence that high beam, halogen headlights tend to increase alert probability over high beam, LED headlights, when the lighbar was off. We found no effect of our lighting treatments on deer alert distance, flight probability, or flight initiation distance. Across all behavioral responses, the random effect deer ID explained 0.86–9.19 × more variation than our lighting treatments, reflecting large differences in responses among deer. Overall, we found that vehicle lighting can impact deer behavior during an imminent, head-on collision scenario, although lighting was ineffective at increasing favorable flight behaviors. Future research should investigate how vehicle lighting treatments affect free-ranging, wild deer in a variety of real-world scenarios and at longer approach distances.
The system is a single hyperspectral imaging instrument that has the unique capability to acquire both fluorescence and reflectance high-spatial-resolution data that is inherently spatially and spectrally registered. Potential uses of this instrument include plant stress monitoring, counterfeit document detection, biomedical imaging, forensic imaging, and general materials identification. Until now, reflectance and fluorescence spectral imaging have been performed by separate instruments. Neither a reflectance spectral image nor a fluorescence spectral image alone yields as much information about a target surface as does a combination of the two modalities. Before this system was developed, to benefit from this combination, analysts needed to perform time-consuming post-processing efforts to co-register the reflective and fluorescence information. With this instrument, the inherent spatial and spectral registration of the reflectance and fluorescence images minimizes the need for this post-processing step. The main challenge for this technology is to detect the fluorescence signal in the presence of a much stronger reflectance signal. To meet this challenge, the instrument modulates artificial light sources from ultraviolet through the visible to the near-infrared part of the spectrum; in this way, both the reflective and fluorescence signals can be measured through differencing processes to optimize fluorescence and reflectance spectra as needed. The main functional components of the instrument are a hyperspectral imager, an illumination system, and an image-plane scanner. The hyperspectral imager is a one-dimensional (line) imaging spectrometer that includes a spectrally dispersive element and a two-dimensional focal plane detector array. The spectral range of the current imaging spectrometer is between 400 to 1,000 nm, and the wavelength resolution is approximately 3 nm. The illumination system consists of narrowband blue, ultraviolet, and other discrete wavelength light-emitting-diode (LED) sources and white-light LED sources designed to produce consistently spatially stable light. White LEDs provide illumination for the measurement of reflectance spectra, while narrowband blue and UV LEDs are used to excite fluorescence. Each spectral type of LED can be turned on or off depending on the specific remote-sensing process being performed. Uniformity of illumination is achieved by using an array of LEDs and/or an integrating sphere or other diffusing surface. The image plane scanner uses a fore optic with a field of view large enough to provide an entire scan line on the image plane. It builds up a two-dimensional image in pushbroom fashion as the target is scanned across the image plane either by moving the object or moving the fore optic. For fluorescence detection, spectral filtering of a narrowband light illumination source is sometimes necessary to minimize the interference of the source spectrum wings with the fluorescence signal. Spectral filtering is achieved with optical interference filters and absorption glasses. This dual spectral imaging capability will enable the optimization of reflective, fluorescence, and fused datasets as well as a cost-effective design for multispectral imaging solutions. This system has been used in plant stress detection studies and in currency analysis.
Growing plants in space will be an essential part of sustaining astronauts during long-range missions. To drive photosynthesis, light-emitting diodes (LEDs) are becoming superior because of their efficiency, longevity, small size, safety, and wavelength versatility. Isolating the effects of certain wavelengths on plant growth when combined with white light is attracting attention. To optimize crop production/quality in space, this study has aimed to configure novel light recipes for the Advanced Plant Habitat currently aboard the International Space Station (ISS). By using white light as a background to maintain normal growth, the addition of monochromatic wavelengths provides a clearer understanding of how each part of the visible spectrum affects plant growth. By growing Outredgeous lettuce under six treatments of White (W) LEDs, W + blue (B), W+ green (G), W + red (R), W + far red (FR), and RGB + FR LEDs with ratios similar to natural sunlight, this investigation has assessed differences in biomass, morphology, chlorophyll, and the synthesis of key phytonutrients. The potential for Outredgeous to produce anthocyanin, lutein, potassium, magnesium, and iron is paramount to maintaining astronaut health. The crop responses to each treatment have been evaluated and the optimal LED combination for both plant yield and nutrient content will be presented.
In a semiconductor light emitting diode (LED) a large proportion of the light produced will be internally reflected when it strikes the end face of the LED at a semiconductor-air interface. This is due to the high index of refraction of most LED semiconductor materials. This problem may be partially overcome by modification of the shape of the LED by a reverse taper of the sides of the LED. Light is redirected by the taper to strike the interface at an angle closer to normal. This allows light to exit the LED that would be totally internally reflected in an untapered LED. The novelty of the present invention lies in the tapering of the sides of the LED for increased through transmission of light. Prior art devices have made use surface modifications such as roughening, addition of guiding layers, use of index matching materials and hemispherical shaping of the emitting end of the LED. Current technology LEDs have a transmission efficiency of only a few percent. An increase in this efficiency would be of great value to any technology that makes use of LEDs for light generation. The present invention is related to LAR 1 5050-SB, Collection of Light from Optical Fibers of NA greater than 1.
Growing vegetable crops in space will be an essential part of sustaining astronauts during long-range missions. To drive photosynthesis, red and blue light-emitting diodes (LEDs) have attracted attention because of their efficiency, longevity, small size, and safety. In efforts to optimize crop yield, there is also recent interest in analyzing the subtle effects of additional wavelengths on plant growth. For instance, since plants often look purplish gray under red and blue LEDs, the addition of green light allows easy recognition of disease and the assessment of plant health status. However, it is important to know if wavelengths outside the traditional red and blue wavebands have a direct effect on enhancing or hindering the mechanisms involved in plant growth. In this experiment, a comparative study was performed on two short cycle crops of red romaine lettuce (Lactuca sativa cv. "Outredgeous") and radish (Raphanus sativa cv. 'Cherry Bomb'), which were grown under two light treatments. The first treatment being red (630 nm) and blue (450 nm) LEDs alone, while the second treatment consisted of daylight tri-phosphor fluorescent lamps (CCT approximately 5000 K) at equal photosynthetic photon flux (PPF). The treatment effects were evaluated by measuring the fresh biomass produced, plant morphology and leaf dimensions, leaf chlorophyll content, and adenosine triphosphate (ATP) within plant leaf/storage root tissues.
Abstract Color-mixed (cm) light-emitting diodes (LEDs) are theoretically the most efficient white light emitters, projected to improve white light luminous efficacy by 34% compared to incumbent phosphor converted LEDs. Since white light technology is pervasive and essential, small improvements in LED technology can result in energy savings. However, cm-LEDs are not yet realized due to poor efficacy in green and amber emitting materials, a spectral region colloquially referred to as the Green Gap. ZnGeN 2 is nearly isostructural and closely lattice-matched to GaN and can be heteroepitaxially integrated with existing GaN devices; ZnGeN 2 /GaN hybrid structures are theorized to emit green (~530 nn) light with a spontaneous emission rate 4.6–4.9 times higher than traditional InGaN LEDs when incorporated into III-N LED structures. In this report we demonstrate the molecular beam epitaxy (MBE) growth of GaN and ZnGeN 2 superlattices, an important step towards realizing multiple quantum well structures required for efficient LEDs. Elemental analysis, including atom probe tomography, shows that Ga and Ge are observed in both ZnGeN 2 and GaN layers, degrading the structural uniformity. The lack of elemental abruptness also leads to increased defect luminescence and reabsorption of band edge luminescence. The source of unintentional Ga distributed throughout the ZnGeN 2 layers was identified as excess flux escaping from around the closed MBE shutter. The source of unintentional Ge, which tended to incorporate as a single delta-doped layer in GaN, was identified as Ge riding along the cyclical metal-rich Ga adlayer used for high quality GaN, incorporating during subsequent nitrogen-rich growth step. Modifying the growth strategy results in improved structural quality, elemental abruptness, and luminescence response. This realization of structurally and elementally abrupt interfaces demonstrates the potential of heteroepitaxially integrated binary and ternary nitrides for energy-relevant devices.
Long-term reliability is especially challenging for organic light emitting diodes (OLEDs) used in solid-state lighting applications because OLED lifetime is inversely proportional to luminance, and most lighting applications demand high luminance. This project explored a new strategy to overcome this tradeoff by constructing OLEDs on a substrate with sub-mm, high aspect ratio surface texture. By creating more active OLED area per unit lighting panel area, the device current density required to generate a given panel luminance decreases. We validated this approach for both fluorescent and phosphorescent OLEDs, demonstrating good thickness uniformity on corrugated substrates with area enhancement factors up to 1.4x using a standard thermal evaporator. Relative to planar controls at the same panel current density, the high aspect ratio devices achieve a 2.7-fold increase in operating lifetime and up to a 40% increase in external light extraction efficiency. Experiments carried out on a pilot-line OLED manufacturing system demonstrated good coating uniformity, indicating that this approach has the potential to be implemented at scale and therefore offers a powerful pathway to improve the efficiency and lifetime of OLED lighting.
Small-signal diodes are placed in series with light-emitting diodes (LED's) to stabilize LED output against temperature fluctuations. Simple inexpensive method compensates for thermal fluctuations over a broad temperature range. Requiring few components, technique is particularly useful where circuit-board space is limited.
Light flashes on to indicate high current. Simple, inexpensive display circuit indicates when 3,000-A welding current flows in welding gun. Onset of welding current induces voltage and current in 1,000-turn, 28-gauge copper-wire coil. Single-transistor amplifier amplifies induced current, energizing light-emitting diode (LED) connected to collector of transistor. Light from LED gives simple, direct indication of welding current.
Future aircraft will use fly-by-light control systems with fiber-linked optical sensors for such measurands as temperature, pressure, and linear and angular position. A digital optical sensor is described which was developed to transmit the angular position of such slowly rotating parts as a throttle of fuel flow control valve on an aircraft. The sensor employs a reflective code plate with ten channels providing a resolution of 0.35 degrees. Two light-emitting diodes with overlapping spectra are used as light sources. A single microoptic multiplexer-demultiplexer composed of a GRIN rod lens and a miniature grating is used to disperse the spectrum and recombine the spectral components from each channel after reflection by the code plate. The results of preliminary environmental tests of this unit are discussed. The sensor has been operated for brief periods of time between -60 C and +125 without adverse effects. Preliminary vibration tests indicate that the unit will work properly at the maximum vibration levels expected in a jet-engine environment.