Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lightweight Structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

CHEM-Based Self-Deploying Spacecraft Radar Antennas

A document proposes self-deploying spacecraft radar antennas based on cold hibernated elastic memory (CHEM) structures. Described in a number of prior NASA Tech Briefs articles, the CHEM concept is one of utilizing open-cell shape-memory-polymer (SMP) foams to make lightweight structures that can be compressed for storage and can later be expanded, then rigidified for use. A CHEM-based antenna according to the proposal would comprise three layers of microstrip patches and transmission lines interspersed with two flat layers of SMP foam, which would serve as both dielectric spacers and as means of deployment. The SMP foam layers would be fabricated at full size at a temperature below the SMP glass-transition temperature (Tg). The layers would be assembled into a unitary structure, which, at temperature above Tg, would be compacted to much smaller thickness, then rolled up for storage. Next, the structure would be cooled to below Tg and kept there during launch. Upon reaching the assigned position in outer space, the structure would be heated above Tg to make it rebound to its original size and shape. The structure as thus deployed would then be rigidified by natural cooling to below Tg

Sokolowski, Witold↗
NASA NTRS1990

Space astrophysics with large structures - CASES and P/OF

Space instruments for remote sensing, of the types used for astrophysics and solar-terrestrial physics among many disciplines, will grow to larger physical sizes in the future. The zero-g space environment does not inherently restrict such growth, because relatively lightweight structures can be used. Active servo control of the structures can greatly increase their size for a given mass. The Pinhole/Occulter Facility, a candidate Space Station attached payload, offers an example: it will achieve 0.2 arc s resolution by use of a 50-m baseline for coded-aperture telescopes for hard X-ray and gamma-ray imagers.

Hudson, Hugh S.↗
NASA NTRS2019

Development of Composite Sandwich Bonded Longitudinal Joints for Space Launch Vehicle Structures

The NASA Composite Technology for Exploration (CTE) Project is developing and demonstrating critical composite technologies with a focus on composite bonded joints; incorporating materials, design/analysis, manufacturing, and tests that utilize NASA’s expertise and capabilities. The project has goals of advancing composite technologies and providing lightweight structures to support future NASA exploration missions. In particular, the CTE project will demonstrate weight-saving, performance-enhancing composite bonded joint technology for Space Launch System (SLS)-scale composite hardware. Advancements from the CTE project may be incorporated as future block upgrades for SLS structural components. This paper discusses the details of the development of a composite sandwich bonded longitudinal joint for a generic space launch vehicle structure called the CTE Point Design. The paper includes details of the design, analysis, materials, manufacturing, and testing of sub-element joint test articles to test the capability of the joint design. The test results show that the composite longitudinal bonded joint design significantly exceeds the design loads with a 2.0 factor of safety. Analysis pre-test failure predictions for all sub-element bonded joint test coupons were all within 10% of the average test coupon failure load. This testing and analysis provides confidence in the potential use of composite bonded joints for future launch vehicle structures.

Segal, Kenneth N.↗
NASA NTRSDate not supplied

Testing and Analysis Correlation of a Large-Scale Composite Sandwich Longitudinal Bonded Joint for Space Launch Vehicle Structures

The NASA Composite Technology for Exploration (CTE) Project is developing and demonstrating critical composite technologies with a focus on composite bonded joints; incorporating materials, design/analysis, manufacturing, and tests that utilize NASA’s expertise and capabilities. The project has goals of advancing composite technologies and providing lightweight structures to support future NASA exploration missions. In particular, the CTE project will demonstrate weight-saving, performance-enhancing composite bonded joint technology for Space Launch System (SLS)-scale composite hardware. Advancements from the CTE project may be incorporated as future block upgrades for SLS structural components. This paper discusses the details of the development of a composite sandwich bonded longitudinal joint for a generic space launch vehicle structure called the CTE Point Design. This paper reports on the large-scale longitudinal bonded joint test articles that were fabricated and tested under axial compressive loading conditions to test the capability of the bonded joint design for buckling and joint failure. Test and analysis correlation of an as-manufactured undamaged longitudinal bonded joint panel are presented in the paper for tests to the onset of buckling and panel failure. Analysis predictions for buckling initiation and panel failure were both within 10% of the longitudinal bonded joint panel test results. This testing and analysis provide confidence in the potential use of composite bonded joints for future launch vehicle structures.

David W Sleight↗
NASA NTRSDate not supplied

Recent Advances in Structural Carbon Nanotube Composites

Carbon nanotubes (CNT) have been a subject of investigation for more than two decades. Part of the interest in CNTs was driven by CNT tensile mechanical properties at the nanoscale that suggest their potential to outperform state-of-the-art (SOA) lightweight structural materials. Early work on the development of CNT nanocomposites involved the dispersion of CNT powder into polymer matrices. Although low levels of CNT doping resulted in meaningful increases in electrical conductivity to enable applications such as electrostatic charge dissipation, the highest concentrations of CNTs in these lightly doped nanocomposites did not yield mechanical properties that could compete with SOA carbon fiber composites. The maximum concentration of CNTs in lightly doped nanocomposites was limited to about 5% due to increases in viscosity that prevent the fabrication of good quality nanocomposites. At the lower concentrations, properties of the resulting nanocomposites were analogous to those of composites made with very short, chopped carbon fibers. About ten years ago, CNTs became available in continuous fiber form, allowing the investigation of processing methods to incorporate much higher CNT content into composites. Recent developments in CNT composite fabrication have yielded improved mechanical properties and indicate that while some standard carbon fiber composite processing methods can be used, CNTs have unique microstructural features that require techniques tailored to access the hierarchical features of CNTs. This presentation will discuss the evolution of structural CNT mechanical property advancements and collaboration mechanisms for research across federal labs, academia, and industry that accelerated the maturation of structural CNTs.

Carbon Nanotubes↗
NASA NTRS1986

System concept for a moderate cost Large Deployable Reflector (LDR)

A study was carried out at JPL during the first quarter of 1985 to develop a system concept for NASA's LDR. Major features of the concept are a four-mirror, two-stage optical system; a lightweight structural composite segmented primary reflector; and a deployable truss backup structure with integral thermal shield. The two-stage optics uses active figure control at the quaternary reflector located at the primary reflector exit pupil, allowing the large primary to be passive. The lightweight composite reflector panels limit the short-wavelength operation to approximately 30 microns but reduce the total primary reflector weight by a factor of 3 to 4 over competing technologies. On-orbit thermal analysis indicates a primary reflector equilibrium temperature of less than 200 K with a maximum gradient of about 5 C across the 20-m aperture. Weight and volume estimates are consistent with a single Shuttle launch, and are based on Space Station assembly and checkout.

Swanson, P. N.↗
NASA NTRS2005

Multi-Scale Sizing of Lightweight Multifunctional Spacecraft Structural Components

This document is the final report for the project entitled, "Multi-Scale Sizing of Lightweight Multifunctional Spacecraft Structural Components," funded under the NRA entitled "Cross-Enterprise Technology Development Program" issued by the NASA Office of Space Science in 2000. The project was funded in 2001, and spanned a four year period from March, 2001 to February, 2005. Through enhancements to and synthesis of unique, state of the art structural mechanics and micromechanics analysis software, a new multi-scale tool has been developed that enables design, analysis, and sizing of advance lightweight composite and smart materials and structures from the full vehicle, to the stiffened structure, to the micro (fiber and matrix) scales. The new software tool has broad, cross-cutting value to current and future NASA missions that will rely on advanced composite and smart materials and structures.

Bednarcyk, Brett A.↗
NASA NTRS1981

Advanced solar concentrator: Executive summary

The preliminary design of a point-focusing solar concentrator, consisting of a steerable space frame structure supporting a paraboloidal mirror glass reflector, is described. A mass production, operation, and maintenance cost assessment is presented. A conceptual evaluation of a modified concentrator design is included. The detailed design of one of the lightweight, structurally efficient reflective elements comprising the paraboloidal reflective surface is given.

Source record↗
NASA NTRS1993

Aircraft empennage structural detail design

The purpose of this project is to provide an empennage structural assembly that will withstand the operational loads defined in FAR Part 23, as well as those specified in the statement of work, i.e. snow, rain, humidity, tiedown forces, etc. The goal is to provide a simple yet durable lightweight structure that will transfer the aerodynamic forces produced by the tail surfaces through the most efficient load path to the airframe. The structure should be simple and cost-effective to manufacture and repair. All structures meet or exceed loading and fatigue criteria. The structure provides for necessary stiffness and ease of maintenance.

Lesnewski, David↗
NASA NTRS2008

Electron Beam Freeform Fabrication: A Fabrication Process that Revolutionizes Aircraft Structural Designs and Spacecraft Supportability

The technological inception and challenges, as well as current applications of the electron beam freeform fabrication (EBF3) process are outlined. The process was motivated by the need for a new metals technology that would be cost-effective, enable the production of new alloys and that would could be used for efficient, lightweight structures. EBF3 is a rapid metal fabrication, layer-additive process that uses no molds or tools and which yields properties equivalent to wrought. The benefits of EBF3 include it near-net shape which minimizes scrap and reduces part count; efficiency in design which allows for lighter weight and enhanced performance; and, its "green" manufacturing process which yields minimal waste products. EBF3 also has a high tensile strength, while a structural test comparison found that EBF3 panels performed 5% lower than machined panels. Technical challenges in the EBF3 process include a need for process control monitoring and an improvement in localized heat response. Currently, the EBF3 process can be used to add details onto forgings and to construct and form complex shapes. However, it has potential uses in a variety of industries including aerospace, automotive, sporting goods and medical implant devices. The novel structural design capabilities of EBF3 have the ability to yield curved stiffeners which may be optimized for performance, low weight, low noise and damage tolerance applications. EBF3 has also demonstrated its usefulness in 0-gravity environments for supportability in space applications.

Taminger, Karen M.↗
NASA NTRS1986

The pultrusion process for structures on advanced aerospace transportation systems

The pultrusion process, which has the potential for use in the manufacture of structures for aerospace hardware, is described. In this process, reinforcing fibers are pulled continuously through a resin system for wetting and subsequently through a heated die for polymerization. By using this process, fabrication of very long lengths of high strength, lightweight structures with consistently high quality for aerospace applications is possible. The more conventional processes involve hand lay-up, vacuum bagging, autoclaving or oven curing techniques such that lengths of structural elements produced are limited by the lengths of autoclaves or curing ovens. Several types of developmental structural elements are described in which fiberglass, aramid, graphite, and hybrid fiber systems have been used as reinforcements in an epoxy matrix and their flexural properties compared. Reinforcement fibers having tailor-made orientations which achieve tailor-made strength in the pultrusions are described. The potential aerospace applications for the pultruded products are described with advantages cited over conventional hand lay-up methods.

Wilson, Maywood L.↗
NASA NTRS1982

Space station preliminary design report

The results of a 3 month preliminary design and analysis effort is presented. The configuration that emerged consists of a very stiff deployable truss structure with an overall triangular cross section having universal modules attached at the apexes. Sufficient analysis was performed to show feasibility of the configuration. An evaluation of the structure shows that desirable attributes of the configuration are: (1) the solar cells, radiators, and antennas will be mounted to stiff structure to minimize control problems during orbit maintenance and correction, docking, and attitude control; (2) large flat areas are available for mounting and servicing of equipment; (3) Large mass items can be mounted near the center of gravity of the system to minimize gravity gradient torques; (4) the trusses are lightweight structures and can be transported into orbit in one Shuttle flight; (5) the trusses are expandable and will require a minimum of EVA; and (6) the modules are anticipated to be structurally identical except for internal equipment to minimize cost.

Source record↗
NASA NTRS1978

Planning for large construction projects in space

The paper discusses briefly some broad plans for developing the technology needed for large construction projects in space ranging from orbiting solar power stations to large communications antennas. Space construction classes include assembly of modules, deployment of compacted structures, assembly of passive preformed pieces, and fabrication of structures from sheet stock. Technological areas related to structural concepts include (1) analyses for prediction of structural behavior, structural/control interaction, electromagnetic and control performance, and integrated design development; (2) electronics for signal conditioning and data acquisition, power distribution, and signal channel interference and multipaction; (3) concepts for shape control, attitude/pointing control, and orbital transfer and station keeping; and (4) materials and techniques for 30-year dimensional stable composites, thermal control, thin-lightweight structural alloys, and material joining in space. The concept of a power module for the construction operations is discussed along with a concept for a habitability module.

Disher, J. H.↗
NASA NTRS2008

Optical Coating Performance and Thermal Structure Design for Heat Reflectors of JWST Electronic Control Unit

The James Webb Space Telescope (JWST) consists of an infrared-optimized Optical Telescope Element (OTE) that is cooled down to 40 degrees Kelvin. A second adjacent component to the OTE is the Integrated Science Instrument Module, or ISIM. This module includes the electronic compartment, which provides the mounting surfaces and ambient thermally controlled environment for the instrument control electronics. Dissipating the 200 watts generated from the ISIM structure away from the OTE is of paramount importance so that the spacecraft's own heat does not interfere with the infrared light detected from distant cosmic sources. This technical challenge is overcome by a thermal subsystem unit that provides passive cooling to the ISIM control electronics. The proposed design of this thermal radiator consists of a lightweight structure made out of composite materials and low-emittance metal coatings. In this paper, we will present characterizations of the coating emittance, bidirectional reflectance, and mechanical structure design that will affect the performance of this passive cooling system.

Quijada, Manuel A.↗
NASA NTRS1975

Computer aided flexible envelope designs

Computer aided design methods are presented for the design and construction of strong, lightweight structures which require complex and precise geometric definition. The first, flexible structures, is a unique system of modeling folded plate structures and space frames. It is possible to continuously vary the geometry of a space frame to produce large, clear spans with curvature. The second method deals with developable surfaces, where both folding and bending are explored with the observed constraint of available building materials, and what minimal distortion result in maximum design capability. Alternative inexpensive fabrication techniques are being developed to achieve computer defined enclosures which are extremely lightweight and mathematically highly precise.

Resch, R. D.↗
NASA NTRS1982

The outlook for advanced transport aircraft

The technological advances most likely to contribute to advanced aircraft designs and the efficiency, performance, and financial considerations driving the development directions for new aircraft are reviewed. Fuel-efficiency is perceived as the most critical factor for any new aircraft or component design, with most gains expected to come in areas of propulsion, aerodynamics, configurations, structural designs and materials, active controls, digital avionics, laminar flow control, and air-traffic control improvements. Any component area offers an efficiency improvement of 3-12%, with a maximum of 50% possible with a 4000 m range aircraft. Advanced turboprops have potential applications in short and medium haul subsonic aircraft, while a fuel efficient SST may be possible by the year 2000. Further discussion is devoted to the pivoted oblique wing aircraft, lightweight structures, and the necessity for short payback times.

Leavens, J. M., Jr.↗
NASA NTRSDate not supplied

TriTruss Packaging and Deployment Trade Study

An architecture and feasibility study of next generation In-Space Assembled Telescopes (iSAT) concluded that robotic in-space assembly of modular components is necessary to enable large (>15-meter diameter) primary apertures. The iSAT study recommended that the foundational structure be assembled from modular TriTruss modules that are packaged for launch, deployed on-orbit and robotically assembled into the final configuration. This paper will describe and summarize the results of a trade study that investigated viable concept of operations (ConOps) for the packaging and deployment (P&D) of individual planar TriTruss modules that could be assembled to form a large aperture iSAT. The ideal TriTruss P&D concept is defined as one that: allows for efficient packaging; has sufficient geometric versatility to be launch vehicle independent; provides a stiff and lightweight structure; has low mechanical complexity; and has component modularity. The P&D concept should allow for prelaunch subsystem or utility integration if required. The concept would be kinematically simple and be robotically deployed using a minimum number of specialized tools. In this first phase of an ongoing more comprehensive trade study, concepts were proposed and then evaluated based on initial metrics representing features of an ideal P&D concept. The P&D concepts evaluated are categorized as: core collapse, face collapse, and erectable structures. Sub-scale models were constructed to help understand the kinematics and mechanical complexity required to enable P&D. Based on a weighting scale, the most promising candidate P&D concepts have selected and will undergo more rigorous structural design, analysis, and testing in the study’s next phase. The ultimate goal of the comprehensive trade study will be to recommend a single TriTruss design and associated P&D concept that will be built and evaluated at NASA Langley Research Center’s In-Space Assembly Laboratory.

in-space assembly (ISA)↗
NASA NTRS1992

Spacecraft dynamics characterization and control system failure detection, volume 1

The work under this grant has been directed to two aspects of the control of flexible spacecraft: (1) the modeling of deployed or erected structures including nonlinear joint characteristics; and (2) the detection and isolation of failures of the components of control systems for large space structures. The motivation for the first of these research tasks is the fact that very large assemblies in space will have to be built or deployed in situ. A likely scenario is, in fact, a combination of these wherein modules which are folded for transportation into orbit are erected to their final configuration and then jointed with other such erected modules to form the full assembly. Any such erectable modules will have joints. It remains to be seen whether or not joints designed for operational assemblies will have nonlinear properties, but it seems prudent to develop a methodology for dealing with that possibility. The motivation for the second of these research tasks is the fact that we foresee large assemblies in space which will require active control to damp vibrations and/or hold a desired shape. Lightweight structures will be very flexible, with many elastic modes having very low frequencies. In order to control these modes well, the control system will likely require many sensors and many actuators, probably distributed over much of the structure. The combination of a large number of control system components with long operational periods virtually guarantees that these systems will suffer control system component failures during operation. The control system must be designed to tolerate failures of some sensors and actuators, and still be able to continue to perform its function.

Source record↗