Search NASA⌕ Search

SEARCH · Search NASA

Results for “METAL FUEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Epsilon Metal: A Waste Form for Noble Metals from Used Nuclear Fuel

Epsilon metal (e-metal) is the metallic phase that forms as inclusions at the grain boundaries in the UO2 fuel during reactor operation. This metal is composed of Pd, Mo, Rh, Ru, and Tc. These metallic inclusions are insoluble in strong acid and remnants of these metallic inclusions have been found in the UO2 matrix that remains from the natural reactors in Gabon that were active 1.8 billion years ago, therefore e-metal should be an excellent waste form for the immobilization of the long-lived isotopes 107Pd (6.5 ? 106 a) and 99Tc (2.13 ? 105 a), with 99Tc being the isotope of interest for repository performance. Therefore, the chemical durability of this potential waste form is assessed in this study. Typically, corrosion rates for metallic materials are measured electrochemically because they are quick, inexpensive, and can reveal the mechanism by which a metal corrodes, at least initially. However, in a repository the waste form would be subjected to slowly flowing water without an applied electrical potential over long time periods. Therefore, the corrosion rates of e-metal specimens were measured with both electrochemical tests and the single-pass flow-through test (SPFT). Potentiodynamic and potentiostatic polarization results suggest that a thin passive film exists on the alloy surface, which seems to be responsible for its high corrosion resistance. Additionally, X-Ray photoelectron spectroscopic results suggest that Pd oxides are significantly enriched in the passive film Results from the SPFT show that the dissolution rates were weakly dependent on pH. Only Mo and Re were found in solution and were used for the calculation of the dissolution rates. In general, the electrochemically determined corrosion rates agree reasonably well with the initial dissolution rate measured with the SPFT test, but they are about one or two orders of magnitude higher than the steady state rates. The causes for this discrepancy are discussed.

epsilon-metal, nuclear waste form, corrosion, sing↗
DOE OSTI2025

Development and preliminary validation of a mechanistic multiscale model for fuel-cladding chemical interaction in metallic nuclear fuels

Despite decades of fuel rod material and design improvements, fuel-cladding chemical interaction (FCCI) remains the single-most lifetime-limiting behavior for modern metallic fuel rods. Constraining fuel lifetime increases operating costs, limiting the economic viability of commercializing metallic nuclear fuel technology. A mechanistic multiscale model utilizing the finite element method-based MARMOT and BISON codes was developed to more confidently predict cladding-side FCCI and its impact on fuel performance. The new BISON model incorporates mesoscale models for the effects of fuel microstructure evolution on the transport of wastage-inducing lanthanides through the fuel and for the kinetics of cladding wastage layer growth. The mesoscale models, in turn, build on lanthanide transport property data obtained from the atomistic scale. Preliminary validation studies using wastage thickness and cladding profilometry data from four fuel rods irradiated in Experimental Breeder Reactor II experiment X447 and one fuel rod from Fast Flux Test Facility experiment IFR1 show that the new model predicts cladding wastage and its effects on cladding deformation as well as existing empirical FCCI correlations. The new model is expected to aid in the design of new metallic fuel concepts, including fuel additives, cladding liners, and sodium-free annular fuel geometries. In conclusion, future work will focus on broader validation and refinement of the model’s treatment of different fuel alloys and cladding materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Direct utilization of gaseous fuels in metal supported solid oxide fuel cells

Direct utilization and internal reforming of gaseous fuels is investigated on symmetric-architecture metal supported solid oxide fuel cells (MS-SOFCs) with thin ceramic electrolyte and scaffold backbone layers, and low cost ferritic stainless steel supports on both sides. Infiltrated Pr-oxide and Ni/samarium-doped ceria catalysts are added to the cathode and anode electrodes, respectively. Initial performance and durability is evaluated for MS-SOFCs operating with natural gas, propane, ammonia, and dimethyl ether at 700 °C. Cells for natural gas and propane utilize a novel high entropy alloy (HEA) catalyst for internal reforming with performance and degradation rates similar to H 2 (0.5W cm -2 and ~12%/100 h). In conclusion, initial testing with sulfur shows reversible degradation for levels found in natural gas and irreversible degradation for higher levels found in commercial propane. Overall, MS-SOFCs show successful fuel flexibility.

08 HYDROGEN↗
DOE OSTI2021

Correlating Nanoscale Secondary Ion Mass Spectrometry and Atom Probe Tomography Analysis of Uranium Enrichment in Metallic Nuclear Fuel

Distribution and enrichment of 235U within nuclear fuels are essential to material performance and reactor safety. With the development of metallic U fuels, understanding 235U homogeneity has become increasingly important, however, it is difficult to map with high spatial, and mass resolution to analyze both matrix and secondary phase precipitates. Here, we analyze 235U enrichment in matrix and carbide phases in LEU-Mo via two chemical imaging modalities: nanoscale secondary ion mass spectrometry (nanoSIMS) and atom probe tomography (APT). NanoSIMS and APT provided consistent results, with no statistically significant difference between measured and nominal enrichment (19.75 % 235U).

U-10Mo, atom probe tomography, nanoscale secondary↗
DOE OSTI2024

Concept of Operations for Advanced Reactor Spent Nuclear Fuel Management

This presentation presents a preliminary description of a concept of operations to incorporate advanced-reactor spent nuclear fuel (SNF) into an integrated waste-management system (IWMS). The evaluation includes SNF from four advanced-reactor concepts with the following fuel types: (1) small modular reactors using oxide fuels, (2) tristructural-isotropic (TRISO) fuels, (3) metallic fuels, and (4) fuel salts. To provide context for the proposed concept of operations for advanced reactors, a comparison is made with traditional light-water reactors (LWRs) to identify potential gaps in the IWMS. The technical differences between advanced reactors and LWRs are assessed to determine the feasibility of managing advanced-reactor waste streams using existing operations and technology. This presentation emphasizes fuel types from Advanced Reactor Demonstration Program reactors: Xe 100, which uses TRISO fuel and Natrium, with its metallic fuels while also analyzing management options for molten-salt reactors and advanced light-water reactors (ALWRs). Understanding the storage, transportation, and disposal requirements of SNF is dependent on both the quantity and characteristics of the SNF generated by nuclear reactors. This presentation provides a high level overview, comparing the anticipated concept of operations for different SNFs from advanced reactors. The IWMS includes at-reactor storage, transportation, potential off-site storage, potential treatment, and disposition. To assess the potential effect of advanced-reactor concept of operations on the IWMS, estimates were made for fuel characteristics that contribute to storage, transportation, disposal, and possible treatment of advanced-reactor SNF. These include canister heat load, dose rates, and criticality-control limits, which are important for determining the condition and configuration of the advanced reactor SNF. At-reactor storage of LWR SNF traditionally involves a spent-fuel pool (SFP) before transfer to an independent spent-fuel storage installation. However, some advanced-reactor concepts, particularly those using TRISO and salt fuels, do not anticipate the use of an SFP. This difference in at-reactor storage could impact the IWMS. Additionally, transportation of advanced-reactor SNF may include additional processes tied to potential off gassing, and transportation of microreactor SNF may occur within the reactor vessel. Some advanced-reactor SNF could also undergo treatment to meet requirements of an acceptable waste form for disposition, and the treatment location will be a major contributor to efficiently performing IWMS responsibilities. Moreover, the quantity of SNF generated is an important consideration for IWMS because it could affect the size of the transportation fleet and potential off-site storage requirements. Additionally, volume and heat load are the primary drivers for SNF disposition. This presentation compares potential packaging options for advanced reactor SNF with traditional LWR packaging to provide a high-level comparison for the needs of the IWMS for advanced-reactor SNF.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Dynamic System Scaling Application to Accelerated Nuclear Fuel Testing

The development of nuclear fuel and materials requires a continuous effort to investigate the acute and prolonged effects of irradiation, thermal-material stress, chemical change, or other conceivable damage mechanics acquired during normal operation or accident scenarios throughout its lifetime. As in-core fuel property measurement techniques advance to support in the real-time, non-invasive, and enhanced accuracy realm, it is the future of fuel development to pursue to higher degrees of control, predictability of integral test behavior via separate effects test (SET), and shorter test time intervals. The fuel development life cycle from initial concept to commercial licensing is approximated to be 20 years and current literature suggests by optimizing fuel performance codes with SETs, the process could possibly be compressed to 5 to 10 years. Recently, a research group in the Idaho National Laboratory (INL) is testing reduced scale fuel rods and increased power density to accelerate evolution of fuel phenomena in metallic fuels. In support of nuclear fuel rod development, compressing fuel test process, and accelerating fuel phenomena, it was the purpose of this study to investigate nuclear fuel performance phenomena via literature review and effectively scale the initial conditions, boundary conditions, and geometric properties to describe the time-dependent response including to fuel burnup, thermal and mechanical stress, transmutations and inter-diffusion, and other relevant observed phenomena. The study was based on BISON simulations of historic EBR-II metallic fuel experiments and Dynamical System Scaling (DSS) method are utilized to assess effects of scaling activity including fuel phenomena acceleration and calculations of time-dependent distortions. The research successfully scaled metallic fuel phenomena, accelerated fuel testing, and assessed the distortions for each scaled case derived.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Annular Metallic Nuclear Fuel Informatics at 50 nm Resolution

U-10wt.% Zr (U-10Zr) based metallic fuel is the leading candidate for next-generation sodium cooled fast reactor in United States. Advanced post-irradiation characterization (from sub-nanometer to micrometer) helps to understand fuel microstructure and property change during irradiation, benefiting fuel qualification for commercial application. With high velocity image data generating method, an automatic way to extract the microstructural information quantitively can better serve the needs from post irradiation characterization. A trained machine learning model, named Decision Tree, is employed to categorize pores caused by fission gas release and to aid phase identification. This work presents a showcase of this approach on different irradiated U-10Zr metallic fuels. This quantitative data offers insights into the fission product migration and potentially thermal conductivity degradation. This information from machine learning will be fed into fuel design code for better prediction of fuel performance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

BISON: A Flexible Code for Advanced Simulation of the Performance of Multiple Nuclear Fuel Forms

BISON is a nuclear fuel performance application built using the Multiphysics Object-Oriented Simulation Environment (MOOSE) finite element library. One of its major goals is to have a great amount of flexibility in how it is used, including in the types of fuel it can analyze, the geometry of the fuel being modeled, the modeling approach employed, and the dimensionality and size of the models. Fuel forms that can be modeled include standard light water reactor fuel, emerging light water reactor fuels, tri-structural isotropic fuel particles, and metallic fuels. BISON is a platform for research in nuclear fuel performance modeling while simultaneously serving as a tool for the analysis of nuclear fuel designs. Recent research in BISON includes techniques such as the extended finite element method for fuel cracking, exploration of high-burnup light water reactor fuel behavior, swelling behavior of metallic fuels, and central void formation in mixed-oxide fuel. BISON includes integrated documentation for each of its capabilities, follows rigorous software quality assurance procedures, and has a growing set of rigorous verification and validation tests.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

A critical analysis of U-Pu-Zr phase transitions using calorimetric, microstructural, and phase equilibria data

Metallic fuels consisting primarily of uranium, plutonium, and zirconium (U-Pu-Zr) are a leading material candidate for fast-spectrum nuclear reactors. Early demonstration programs proved the principle of safe and efficient fast reactor operation, however there is still considerable uncertainty regarding the phase equilibria and microstructural evolution across the ternary composition space. Quantitative phase formation and identification measurements are scarce and often incomplete, with studies reporting either phase transition temperatures or phase identification data, but not both from the same specimens. In this study, we critically compared experimental and calculated phase transition data and correlated with the microstructure and phase characterization data of as-cast and annealed U-Pu-Zr alloys. Differential scanning calorimetry (DSC) was used to measure phase transitions in the subsolidus regions (723−948 K) of three ternary U-Pu-Zr alloys with similar plutonium concentrations but various U/Zr ratios. Due to sluggish kinetics and narrow ranges of phase stability, complex peaks required the use of a Frazier-Suzuki peak fitting algorithm to deconvolute and calculate transition peak temperatures and enthalpies. We also identified trends of phase transition behavior by critically comparing our DSC data with previous phase transition measurements as well as historical and calculated phase equilibrium diagrams. In conclusion, this provides a critical approach for benchmarking and assessing the quality of new U-Pu-Zr phase equilibria data prior to its incorporation into nuclear material databases.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2003

Nanotechnology Investigated for Future Gelled and Metallized Gelled Fuels

The objective of this research is to create combustion data for gelled and metallized gelled fuels using unique nanometer-sized gellant particles and/or nanometer-sized aluminum particles. Researchers at the NASA Glenn Research Center are formulating the fuels for both gas turbine and pulsed detonation engines. We intend to demonstrate metallized gelled fuel ignition characteristics for pulse detonation engines with JP/aluminum fuel and for gas turbine engines with gelled JP, propane, and methane fuel. The fuels to be created are revolutionary as they will deliver the highest theoretically maximum performance of gelled and metallized gelled fuels. Past combustion work has used micrometer-sized particles, which have limited the combustion performance of gelled and metallized gelled fuels. The new fuel used nanometer-sized aluminum oxide particles, which reduce the losses due to mismatch in the gas and solid phases in the exhaust. Gelled fuels provide higher density, added safety, reduced fuel slosh, reduced leakage, and increased exhaust velocity. Altogether, these benefits reduce the overall size and mass of the vehicle, increasing its flexibility.

Palaszewski, Bryan A.↗
DOE OSTI2021

Automatic information extraction from neutron radiography imaging to estimate axial fuel expansion in $\mathrm{EBR-II}$

Approximately 130,000 metal fuel pins were irradiated in the Experimental Breeder Reactor II (EBR-II) during its 30 years of operation to develop and characterize existing and prospective fuels. For many of the metal fuel irradiation experiments, neutron radiography imaging was performed to characterize fuel behavior, like fuel swelling. However, due to the lack of technology or resources, many of the images have not been processed or were processed manually through visual examination. This paper represents first-attempt to develop an image processing algorithm capable of automatically extracting information regarding the degree of fuel swelling from neutron radiography imaging. The algorithm was applied to 120 images of three different metallic fuel pin compositions—U-10Zr, U-8Pu-10Zr, and U-19Pu-10Zr. The algorithm performs operations of image intensity adjustment, image binarization, region finding, and labeling to extract information about fuel swelling. The average growth for U-10Zr was found to be 8.49% with 95% Confidence Interval (CI) [8.33 –8.66%], for U-8Pu-10Zr — 7.50% with 95% CI [7.23 – 7.78%], and for U-19Pu-10Zr — 3.15%, with 95% CI [2.40 – 3.91%]. The results obtained by applying this automatic image processing algorithm are consistent with previously reported studies of the same types of fuels. The automatic image processing algorithm will be expanded to include thousands of available neutron radiography images and different types of fuels to investigate empirical dependencies of fuel swelling, which can be subsequently applied to advanced fuel modeling. Results from this study can later be compared to BISON simulations to further benchmark modeling efforts and develop assessment cases.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Advanced Electron Microscopy Characterization of the Fuel-Cladding Chemical Interaction Region in a High Burnup U-10Zr Fuel

To support the development of U-10Zr metallic fuel, advanced characterization techniques have been applied to the fuel-cladding chemical interaction (FCCI) region in a Na-bonded solid U-10Zr fuel cross-section that was irradiated to a burnup of ~13.1 at.% at the Fast Flux Test Facility. 17 phases were identified in the FCCI region through a combination of high-resolution scanning transmission electron microscopy (STEM), STEM based energy dispersive X-ray spectroscopy (STEM-EDS), and TEM based selective area electron diffraction (TEM-SAED) analysis. In this talk, we will also discuss the implications of results on metallic fuel FCCI by focusing on the formation of Zr rind, fission product migration, and HT-9 cladding integrality under the investigated thermal irradiation conditions. This work complements our previous study on the TEM characterization of the fuel region of this high burnup fuel sample and serves as scientific basis to support metallic fuel development and qualification.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Transmission electron microscopy characterization of the fuel-cladding chemical interactions in HT9 cladded U-10Zr fuel

Fuel cladding chemical interaction (FCCI) is a key phenomenon needs to be better understood to establish the design basis for U-10Zr metallic fuel performance. Characterizing the microstructure and chemical composition of FCCI at micron and sub-micron scale is critically important toward a more mechanistic understanding of FCCI phenomenon and its potential effects on cladding integrity and metallic fuel performance. This paper, by using transmission electron microscopy, investigated the FCCI region in HT9 cladded U-10Zr fuel irradiated to 5.7% FIMA burnup at a peak inner cladding temperature of 615 °C in Fast Flux Test Facility (FFTF). Four distinct layers are identified in the FCCI region. The migration of Fe into the fuel side leads to the formation of several U-Zr-Fe ternary phases, including ?-Fe0.5Zr0.32U0.18, e-Fe0.3Zr0.4U0.3, and ?-Fe0.06Zr0.23U0.71, mingled with UFe2, U6Fe, and U phase at various Fe penetration depth up to ~ 150 µm. On the cladding side, grain coarsening and significant lanthanides infiltration along grain boundaries are observed. Laves phase, (Fe,Cr)2(Mo,W), which typically does not exist in fresh HT9, is identified in a wide radial range in the cladding. The typical HT9 martensitic lath structure and pre-existing M23C6 precipitates disappear, partially or completely, depending on the radial distance from the fuel-cladding interface. Those microstructural and compositional changes could cause mechanical degradation in the HT9 cladding. The present characterization results will improve the understanding of FCCI phenomenon and facilitate the development of microstructure-informed FCCI modeling for metallic fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

IMPACT-01 Assembly Overview [Slides]

The Irradiated Material Properties Accelerated Characterization Test (IMPACT) series of experiments will irradiate three metallic fuel alloy specimens with embedded thermal conductivity probes in the Advanced Test Reactor (ATR). Metallic fuel alloys have long been under investigation for use in advanced reactors on account of their high thermal conductivity. Metallic fuel undergoes dramatic microstructural changes early in life due to fission gas swelling until ~2-3 at% burnup when pores interconnect, thus allowing fission gas to escape into the fuel pin plenum and swelling effectively ceases. The evolution of metallic fuel thermal conductivity during this early phase has never been successfully measured in situ. This experiment will be designed to use advances in measurement sciences to characterize how thermal transport properties evolve while in reactor. The IMPACT experiment consists of three metallic fuel rodlets with thermal conductivity probes axially centered within the fuel specimen. This presentation is an overview of the IMPACT-01 assembly process with a focus MFC fuel fabrication and experiment assembly steps.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

VTR Fuel Design Considerations

This presentation contains a review of fast reactor metal fuel phenomena, fuel failure mechanisms, and associated design parameters followed by discussion of which design parameters were a consideration for VTR fuel. The technology is all found in previously released and published sources, though the perspective on what it means for design of metal fuel for advanced reactor designs is new. The content related to VTR fuel does not include design details that were previously determined to be export controlled, and any previous pre-decisional aspects that might be implied are not relevant today, given that the VTR project was not funded.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Manufacturing porous U10Zr fuels with controlled porosities by SPS and thermal properties

To accommodate the swelling of metallic fuels induced by the fission gas release during burnup in sodium fast reactor for a sodium-free fuel option, advanced U-10Zr fuels with controlled porosity were designed and demonstrated by spark plasma sintering. U-10Zr fuel pellets with manufactured porosities varying from 35% up to fully dense fuel pellets have been fabricated by controlling ball milling times of the starting uranium powders, sintering temperature, pressure, and duration, and the correlation among the microstructure control – porosity – sintering conditions has been established. To further mimick the pore structure in irradiated fuels, different pore formers (NaCl and NH4HCO3) have been used to control the pore size and distribution. Microstructure characterization indicates a lamellar reaction zone of U and Zr, differing from the arc-melted U-10Zr as a result of rapid consolidation of SPS at lower temperature and short durations. The thermal conductivity of U10Zr with different porosities are also measured. Here this work demonstrates the success in manufacturing new metallic fuel forms with controlled porosities and pore distribution, which can be used as model systems to investigate the thermal transfer behavior of metallic fuels in the reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Report on Fuel Cycle Facility Requirements for Deployment of Demonstration Reactors and Potential Evolutionary Fuel Cycle Scenarios

A series of fuel cycle scenarios studies were performed to inform on fuel cycle capacities and facilities needed for large-scale deployment of the Advanced Reactor Demonstration Program (ARDP) reactors and potential future evolutionary fuel cycle scenarios. The reactor deployment and evolutionary fuel cycle scenarios from the present to 2100 were developed based on the following assumptions: 1) achievement of a net-zero emissions economy in the United States by 2050, which requires a nuclear energy generation capacity of ~250 GWe by 2050, 2) the U.S. economic growth of 1% per year from 2051 to 2100, which results in ~340 GWe of nuclear energy capacity in 2100, and 3) commercial-scale recycling and high burnup fuel technologies are available after 2050. Thus, evolutionary fuel cycles with those advanced nuclear technologies start after 2050. A single once-through fuel cycle scenario was assumed from the present to 2050 to achieve a net-zero emissions economy in the United States, and the following four evolutionary fuel cycle scenarios from 2051 to 2100 were considered, 1) Once through fuel cycle with ARDP reactors (Natrium and Xe-100), 2) Once-through fuel cycle with Breed-and-Burn (B&B) fast reactors, 3) Recycling fuel cycle of used metallic fuel in fast reactors, and 4) Recycle fuel cycle of both used uranium oxide and metallic fuels in fast reactors. The projected front-end and back-end fuel cycle capacity demands are compared with the current domestic and global (if needed) fuel cycle capacities.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Alloying–realloying enabled high durability for Pt–Pd-3d-transition metal nanoparticle fuel cell catalysts

Abstract Alloying noble metals with non-noble metals enables high activity while reducing the cost of electrocatalysts in fuel cells. However, under fuel cell operating conditions, state-of-the-art oxygen reduction reaction alloy catalysts either feature high atomic percentages of noble metals (>70%) with limited durability or show poor durability when lower percentages of noble metals (<50%) are used. Here, we demonstrate a highly-durable alloy catalyst derived by alloying PtPd (<50%) with 3d-transition metals (Cu, Ni or Co) in ternary compositions. The origin of the high durability is probed by in-situ/operando high-energy synchrotron X-ray diffraction coupled with pair distribution function analysis of atomic phase structures and strains, revealing an important role of realloying in the compressively-strained single-phase alloy state despite the occurrence of dealloying. The implication of the finding, a striking departure from previous perceptions of phase-segregated noble metal skin or complete dealloying of non-noble metals, is the fulfilling of the promise of alloy catalysts for mass commercialization of fuel cells.

25 ENERGY STORAGE↗