Search NASA⌕ Search

SEARCH · Search NASA

Results for “Modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Synthesis and characterization of biobased copolyesters based on pentanediol: (2) Poly(pentylene adipate–co–terephthalate)

Traditionally, most flexible food packaging is made of linear low-density polyethylene (LLDPE) which cannot easily be recycled, nor will it degrade in a reasonable timescale. In this work, a biobased biodegradable polyester alternative was investigated as a possible replacement for LLDPE. High molecular weight poly (pentylene adipate-co-terephthalate) with a 40/60 adipic acid/terephthalic acid mole ratio was synthesized using direct esterification and polycondensation. Glycerol and hexane-1,2,5,6-tetrol were added as branching agents to better match the structure of the LLDPE which in turn might help the ability of these materials in film-blowing. Thermal, mechanical, and rheological properties of the copolyesters were thoroughly investigated. All copolyesters had a weight-average molecular weight of over 140,000 g/mol, which is necessary for proper rheology, and were thermally stable up to 350°C. Here, the addition of branching agents led to a slight decrease in crystallinity, d-spacing, melting temperature, enthalpy of melting, stress at break, and elongation at break. However, an increase in Young's modulus and complex viscosity at high frequency were observed compared to PPeAT60 without branching agent added. Although the improved crystallinity and mechanical properties of the copolyesters made them viable for film-blowing, the slow crystallization rate creates a major challenge.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Synthesis and characterization of biobased copolyesters based on pentanediol: (1) Poly(pentylene dodecanoate–co–furandicarboxylate)

A series of biobased aliphatic-aromatic copolyesters, poly(pentylene dodecanoate-co-furandicarboxylates) (PPeDFs) were synthesized via an esterification and polycondensation melt process. The copolyesters were characterized using gel permeation chromatography, Fourier transform infrared spectroscopy, 1 H NMR spectroscopy, differential scanning calorimetry, thermogravimetric analysis, wide angle x-ray scattering, and tensile testing. The thermal transition behavior was strongly dependent on composition, with the melting and glass transition temperatures reaching a minimum at approximately equimolar ratio of D to F. All copolyesters were stable below 300°C with their R 600 (the weight of material remaining at 600°C) values increasing with F fraction. PPeD to PPeDF30 (e.g., mole ratio D/F = 7:3) show sharp PPeD crystalline reflections only while broad PPeF reflections are shown in PPeF and PPeDF90. PPeDF40 to PPeDF80 showed both crystal structures. The fractional crystallinity for the PPeD was much higher than PPeF and the fractional crystallinity of the copolymers showed a minimum at D/F ratios closer to the latter. Here, the stress at break and modulus both exhibited maxima at D/F ratios that were either high or low, but somewhat surprisingly a strong maximum in percent elongation at break of over 600% occurs at PPeDF40. For this composition, a typical plastic behavior curve was found including a yield point, high elongation at break, and strain hardening.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Initiator‐Driven Tailoring of Reactivity and Inhibition in Frontally Polymerized Dicyclopentadiene‐Co‐Dihydrofuran Thermosets

Incorporating 2,3‐dihydrofuran (DHF) into dicyclopentadiene (DCPD) enables frontally polymerizable, deconstructible thermosets via acid hydrolysis. At 5–20 mol% DHF and low initiator concentration (~100 ppm), DHF inhibits front propagation, lowers the glass transition temperature ( T g ) by up to 20°C, and quenches the front, especially at 20% DHF. This paper demonstrates that increasing the initiator concentration to 250–1000 ppm overcomes inhibition, enhances front speeds by ~50%, and suppresses quenching at the expense of pot‐life. Above 5 mol% DHF, an emergence of a second exotherm is observed, attributed to increased rate dependence on the inhibition of the initiator by DHF. Void formation from volatile DHF is suppressed by applying 110 kPa nitrogen, though at the cost of reduced front speed. Dynamic mechanical analysis shows that higher initiator concentration produced more highly cross‐linked polymers, with a ~20% increase in storage modulus at 25°C and a 20°C increase in T g .

deconstructible thermosets↗
DOE OSTI2026

DNA Crystals as a Template for Patterned Functional Materials

DNA nanotechnology offers a wide toolkit of molecular functionalities and scales, including intricate motifs less than 10 nm and periodic structures exceeding 100 µm. At larger scales, however, there are often significant tradeoffs for DNA structures, namely stability and mechanical strength. This work describes the design, synthesis, and characterization of a functionalized DNA crystal. Using a ligated DNA crystal grants significant freedom for various functional materials to be applied, in this case, semiconducting cadmium sulfide and palladium metal. Properties investigated in this study include stability, mechanical strength, and optoelectronic properties such as photoluminescence (PL) and electric conductivity. Significant changes are observed based on the functional material applied to DNA crystals. The Young's modulus of the crystal varies by about five orders of magnitude when functionalized with palladium. PL and semiconductive behaviors were observed when cadmium sulfide was attached. These crystals represent an expansion of the capabilities of DNA structures at these length scales, and additionally a platform for future studies exchanging the materials or altering the ligation scheme.

CdS↗
DOE OSTI2024

A double copy from twisted (co)homology at genus one

We study the twisted (co)homology of a family of genus-one integrals — the so called Riemann-Wirtinger integrals. These integrals are closely related to one-loop string amplitudes in chiral splitting where one leaves the loop-momentum, modulus and all but one puncture un-integrated. While not actual one-loop string integrals, they share many properties and are simple enough that the associated twisted (co)homologies have been completely characterized [1]. Using intersection numbers — an inner product on the vector space of allowed differential forms — we derive the Gauss-Manin connection for two bases of the twisted cohomology providing an independent check of [2]. We also use the intersection index — an inner product on the vector space of allowed contours — to derive a double-copy formula for the closed-string analogues of Riemann-Wirtinger integrals (one-dimensional integrals over the torus). Similar to the celebrated KLT formula between open- and closed-string tree-level amplitudes, these intersection indices form a genus-one KLT-like kernel defining bilinears in meromorphic Riemann-Wirtinger integrals that are equal to their complex counterparts.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Mechanical and Thermal Characterization of Additively Manufactured Carbon/Nylon 12 and Carbon/PEEK Composites

This study explores additive manufacturing of carbon fiber-reinforced thermoplastic composites using the Composite-Based Additive Manufacturing (CBAM) process. Carbon/Nylon 12 and Carbon/PEEK composites were fabricated and evaluated through mechanical (compression, tensile, flexural, and impact) and thermal (DSC and TGA) tests. Carbon/PEEK exhibited superior mechanical performance, with 97.5% higher tensile strength, 79.8% higher elastic modulus, and 59.6% higher flexural strength compared to Carbon/Nylon 12. Thermal testing showed that Carbon/PEEK had higher thermal stability, beginning degradation at 350 °C versus 298 °C for Carbon/Nylon. These results indicate that CBAM-fabricated Carbon/PEEK composites are suitable for applications requiring high strength and temperature resistance.

Additive manufacturing↗
DOE OSTI2024

Effects of mercerization and fiber sizing of coir fiber for utilization in polypropylene composites

The use of natural fibers as an alternative to synthetic fibers for reinforcing composites is increasing. However, the poor interfacial adhesion between natural fibers and polymer matrices limits their applications. Several approaches have been considered to improve fiber-matrix adhesion via chemical and/or physical treatment. However, the effectiveness of these treatments varies based on the type of fiber, its source, and its composition. Thus, it is imperative to understand the effectiveness of treatment conditions. In this study, we investigated the influence of alkali treatment and fiber sizing on the chemical, thermal, morphological, and mechanical properties of coir fibers and the interface between coir fiber and polypropylene matrix. Further, it was found that using a 5 wt% sodium hydroxide solution for 6 h at room temperature was the optimal treatment condition that led to an improvement in tensile strength by 58%, tensile modulus by 71%, and elongation at break by 37% compared to untreated fibers, and an increment in interfacial shear strength (IFSS) between coir fibers and polypropylene matrix by 32%. The alkali treatment removed the fiber surface impurities, made the fiber surface rough, and enhanced the fiber crystallinity. Sizing of the alkali-treated fiber led to an improvement in IFSS by 87% with no modification of the fiber’s mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Aluminum/SmCo 5 composites for structural and magnetic applications

Metal-bonded magnetic composites (MBMCs) present a promising alternative to dense sintered magnets, particularly for intricate components. Compared to polymer-based bonded magnets, MBMCs have wider applicability in harsh environments. In this paper, we demonstrate a solid-state shear-based manufacturing technique to introduce localized magnetization into a paramagnetic aluminum matrix by embedding SmCo5 permanent magnet particles. Our magnetic composites display hard magnetic behavior with a coercivity of 13 kOe and a remanent magnetization of 4.32 emu/g. In addition to magnetization, we also report a 9% improvement in Young’s modulus. Despite the local temperature rise during processing, the magnetic phases didn’t decompose into unwanted phases, preserving the composite's hard magnetic properties. Creation of an interfacial metallurgical bond with the matrix ensured the suitability of the composites for structural applications. Our study investigates the mechanical, and functional properties of composites, paving the way for lightweight structural magnetic composites with a transformative potential in the aerospace, nuclear, and automotive applications. This work underscores the potential for further optimization and development to drive innovations in magnet and equipment design.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Electron beam irradiation effects on bulk metals: a comparative study of polycrystalline versus single-crystalline structures

This study investigates the effects of electron beam (e-beam) irradiation on the mechanical and structural properties of eight bulk metallic samples, comprising both polycrystalline (PC) and single-crystalline (SC) forms of Ni, Cr, V, and Ti. These metals were evaluated as potential candidates for beam exit windows in high-power (MW-class) particle accelerators. The primary objective is to identify metals capable of withstanding the conditions of high-power/MW-class e-beam accelerators and serve effectively as exit windows. Selection criteria were based on each metal’s intrinsic properties, power dissipation capability, and irradiation-induced changes in mechanical behavior, including hardness, elastic modulus, and defect density. Comprehensive characterization was conducted using field-emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM–EDS), X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), and nanoindentation, performed both before and after exposure to a ~¿66 kGy dose from a 10 MeV e-beam accelerator. Results revealed that e-beam irradiation induced hardening in PC Ni, whereas PC Ti, commonly used in beam exit windows, exhibited softening. The observed softening in PC Ti is attributed to grain coarsening, elongation, and the formation of twins and twin boundaries, in contrast to the smaller, compressed grains in the pristine (Pr) PC Ti samples, consistent with the Hall–Petch relationship. The stresses due to twinning are small and insignificant in influencing the overall hardening of the PC Ti irradiated sample when compared to the stresses due to the dislocation density. Conversely, SC Ti samples exhibited irradiation-induced hardening. The SC Ti irradiated samples developed additional irradiation-induced modifications in crystallographic texture of (100), (101), (110), (200), (112), (004), and (211) as evidenced from the XRD results, which could probably explain the hardening effect that is caused by irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Graphene reinforced UHMWPE fibers

Thermoplastic polymers are increasingly used in electric vehicles, hydrogen fuel cell vehicles, and other decarbonization applications due to their lightweight and formability. Higher-strength polymers are needed to supplant metals in the vehicle structure, thereby reducing mass and improving efficiency. Ultra-high molecular weight polyethylene (UHMWPE) fibers possess one of the highest strength-to-weight ratios of technical polymers, and further improvement via reinforcement by nanofillers, such as graphene, will expand their performance envelope. Here, in this work, UHMWPE/graphene nanocomposite fibers were gel spun and characterized for their morphological, microstructural, thermal, and mechanical properties. The addition of a low fraction of graphene improved the tensile strength of the fibers by 25% and tensile modulus by 32%. Differential scanning calorimetry showed an increase in melting temperature and degree of crystallinity, which indicates improved coordination of the molecular chains induced by the addition of graphene. The reinforcement also affected the cross-sectional shape of the fibers; the aspect ratio of the fibers’ elliptical shape declined with increasing graphene content showing the skeletal effect of the graphene nanofillers in the polymer matrix. The reinforcing effect of graphene declined above a threshold concentration, and theoretical modeling was applied to demonstrate that increased agglomerates led to reduced properties. This work demonstrates a simple, effective method to produce graphene-reinforced UHMWPE fibers and lays a foundation for understanding the potential for leveraging graphene to form ultra-high-performance nanocomposite fibers for myriad engineering applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Harnessing Machine Learning to Predict MoS 2 Solid Lubricant Performance

Physical vapor deposited (PVD) molybdenum disulfide (MoS 2 ) solid lubricant coatings are an exemplar material system for machine learning methods due to small changes in process variables often causing large variations in microstructure and mechanical/tribological properties. Here, in this work, a gradient boosted regression tree machine learning method is applied to an existing experimental data set containing process, microstructure, and property information to create deeper insights into the process-structure–property relationships for molybdenum disulfide (MoS 2 ) solid lubricant coatings. The optimized and cross-validated models show good predictive capabilities for density, reduced modulus, hardness, wear rate, and initial coefficients of friction. The contribution of individual deposition variables (i.e., argon pressure, deposition power, target conditioning) on coating properties is highlighted through feature importance. The process-property relationships established herein show linear and non-linear relationships and highlight the influence of uncontrolled deposition variables (i.e., target conditioning) on the tribological performance.

MoS2↗
DOE OSTI2024

Increased AGE Cross-Linking Reduces the Mechanical Properties of Osteons

Abstract The osteon is the primary structural component of bone, contributing significantly to its unique toughness and strength. Despite extensive research on osteonal structure, the properties of osteons have not been fully investigated, particularly within the context of bone fragility diseases like type 2 diabetes mellitus (T2DM). This study aims to isolate osteons from bovine bone, simulate the effects of increased advanced glycation end-products (AGEs) in T2DM through ribosylation, and evaluate the mechanical properties of isolated osteons. Osteons extracted from the posterior section of bovine femur mid-diaphysis were processed to achieve a sub-millimeter scale for microscale imaging. Subsequently, synchrotron radiation micro-computed tomography was employed to precisely localize and isolate the osteon internally. While comparable elastic properties were observed between control and ribosylated osteons, the presence of AGEs led to decreased strain to failure. Young’s modulus was quantified (9.9 ± 4.9 GPa and 8.7 ± 3 GPa, respectively), aligning closely with existing literature. This study presents a novel method for the extraction and isolation of osteons from bone and shows the detrimental effect of AGEs at the osteonal level.

Materials Science↗
DOE OSTI2025

Utilization of Hemp Processing Waste for 3D Printing of Biocomposites

Unlike stem biomass, the residues after the extraction of cannabidiol (CBD) oil from hemp flower are challenging to utilize because of their high extractive content (~ 40%, mainly lipids) and are typically considered waste and landfilled. This study presented a novel approach to effectively valorize this underutilized hemp processing waste via chemical processing for three-dimensional (3D) printing applications. Hemp processing waste was processed with sodium hydroxide (NaOH) to control extractives for solving nozzle clogging and then applied as a biofiller in polylactic acid (PLA) composites to improve the mechanical strength. The novelty of this work lies in demonstrating that controlled extractive removal via NaOH treatment not only improves processability but also enhances mechanical performance in 3D-printed biocomposites. We systematically investigated the effect of the processed biofiller content (2.5–10 wt%) on the mechanical and thermal properties of the biocomposites. The decrease in the content of extractives reduced the non-structural components and improved the surface compatibility of the hemp waste with the PLA matrix, thereby enhancing the polymer-biofiller interactions. The best performance was achieved at 2.5 wt% loading, where Young’s modulus increased from 2.3 GPa to 2.6 GPa and tensile strength from 42.7 MPa to 48.8 MPa. Interestingly, the complete removal of extractives also reduced the mechanical strength of their biocomposites, indicating the interfacial adhesion effects of extractives. Furthermore, this study provides new insights into balancing extractive content for optimal mechanical properties, offering a sustainable solution for waste valorization in additive manufacturing.

Additive manufacturing↗
DOE OSTI2025

Temperature-Dependent Mechanical Properties of Ni-Based Concentrated Alloys: Insights from First-Principles Calculations

The present work focuses on predicting temperature-dependent mechanical properties of Ni-based concentrated alloys Ni 18 Cr 10 Co 10 Fe 6 M 4 (abbreviated by X 44 M 4 , with M = Al, V, Mn, Fe, Nb, Mo, and W) using density functional theory (DFT). These predictions are based on shear (plastic) and elastic deformations, utilizing the special quasirandom structure (SQS), the phonon-based quasiharmonic approach (QHA), and the quasistatic approach. The resulting properties include coefficient of thermal expansion via QHA, ideal shear strength (τ IS ), and stable and unstable stacking fault energies (γ SF and γ US ) through pure alias shear deformation, and elastic constants (c ij ), bulk modulus (B 0 ), and shear modules (G 0 ) via elastic deformation. Notably, predicting accurate γ SF is challenging due to uncertainties that can exceed the γ SF values. τ IS and γ US exhibit a strong linear relationship, enabling the accurate prediction of γ US based on the precisely determined τ IS . All mechanical properties of X 44 M 4 decrease with increasing temperature, except for some γ SF cases such as X 44 M 4 with M = V, Mn, Fe, Mo, and W. Among the X 44 M 4 alloys, X 44 Nb 4 exhibits the lowest τ IS , γ US , and G 0 values, and the highest B 0 /G 0 ratio, while X 44 Mn 4 has the lowest B 0 and B 0 /G 0 ratio. We found that volume is a crucial descriptor for understanding and modeling mechanical properties (except B0 and maybe also γ SF ) affected by alloying elements and temperature. Ni-based dilute alloys (e.g., Ni 11 M 1 and Ni 31 M 1 ) and concentrated alloys (e.g., X 44 M 4 ) show similar trends in mechanical properties influenced by alloying elements and temperature, simplifying the analysis and design of Ni-based alloys.

Elastic properties↗
DOE OSTI2025

Assessment of critical flaw sizes and crack driving forces during additive manufacturing of metallic materials

Additive manufacturing (AM) of complex engineering components is often plagued by a high susceptibility to cracking, particularly in high-strength metallic materials. While alloy design efforts have made progress in mitigating solidification defects, there remains a need for mechanistic guidelines to predict susceptibility to solid-state cracking. To address this gap, driving forces for the growth of melt pool cracks are calculated across a wide range of alloys using an efficient computational framework. Calculations are coupled with rapid single track laser experiments to elucidate trends in cracking from laser melting. The analyses conducted here highlight the important role of material properties in susceptibility to cracking, notably fracture toughness and elastic modulus. An important finding is that residual stresses that are limited in magnitude to the yield stress of the material are likely insufficient to drive cracking during cooling. Furthermore, the implications of these results are discussed in the context of alloy design for AM and residual stress accumulation during AM.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Design and scale-up of 3D printed bat houses with biomass-derived polymer composites

Biomass (e.g., pine sawdust, especially high–ash content pine sawdust) is commonly disposed of as waste. Combining biomass with polymers to make composite feedstocks for 3D printing has been explored as a method to reduce or repurpose the biomass waste. Although not all biocomposite properties are known, the wood-based polylactic acid (PLA) composite has promising qualities for applications in ecological settings. In this work, pine wood–PLA composite feedstock was used to 3D print supplemental roost structures for endangered tree-roosting bats, which often face a paucity of suitable naturally occurring roosts. This material combination was selected because it is estimated to degrade faster than the synthetic material systems that are used widely in supplemental bat roosting structures to aid in the conservation of tree roosting bats. The layered, rough surface created by the 3D printing process serves as a surface that bats can grip while roosting. Computer-aided design (CAD) models were generated based on natural roost structures, and a full-size bat house was successfully additively manufactured using a pellet-fed large-scale 3D printing system. The 3D printed hexagon exhibited a tensile strength of 22–23 MPa and a Young’s modulus of 3202–3218 MPa in the x-direction. It has been demonstrated that the 3D printed bat house can be installed on a tree in a stable fashion. This successful demonstration of a bat roost manufactured using a bioderived composite should promote its use in other fish and wildlife structures and broader industrial applications such as construction and automobiles.

3D printing↗
DOE OSTI2026

Can classical DEM simultaneously capture compressibility and flowability of milled biomass?

Accurate prediction of the rheological behavior of biomass is essential for the design and operation of hoppers, feeders, and storage systems in biorefineries. This study examines whether the classical, coarse-grained discrete element method (DEM) formulation can simultaneously reproduce the compressibility and flowability of milled herbaceous biomass, using Miscanthus × giganteus as a representative material. The model represents particles as rigid spheres interacting through Hertz-Mindlin elastic-frictional contacts augmented with an area-dependent cohesion term. Laboratory cyclic compression and wedge-shaped hopper discharge experiments were used as calibration benchmarks. Although the model can independently reproduce each behavior by appropriately tuning particle Young's modulus E and cohesion energy density k, an extensive parametric investigation comprising more than 600 simulations reveals that the optimal parameter regions for compression and hopper flow are distinct and non-overlapping in (E, k) space. Surrogate surface analysis further shows that the corresponding objective-function valleys exhibit similar trends but are approximately parallel and spatially offset, precluding a unified calibration within the explored domain. Sensitivity analysis indicates that compressibility is governed predominantly by stiffness and cohesion, whereas the slope of the mass flow rate-opening relation in hopper discharge is primarily controlled by tangential friction. Extensions incorporating particle size distribution and clumped-sphere representations do not eliminate the incompatibility. These results systematically reveal, for the first time, the structural limitation of simplified DEM formulations in representing biomass rheological behavior, underscoring the necessity for models incorporating additional physical mechanisms, such as particle deformability or enhanced interlocking, to achieve unified predictive capability for biomass handling behavior.

09 BIOMASS FUELS↗
DOE OSTI2024

Mesophase pitch-based high performance carbon fiber production using coal extracts from mild direct coal liquefaction

Mild direct coal liquefaction (autogenous pressure, no catalyst, no H2 gas) of Springfield coal in fluid catalytic cracking decant oil is shown to effectively produce coal extract precursors to spinnable mesophase pitch. Here this work demonstrates that the coal extract can be thermally treated to obtain mesophase pitch in a facile one-step process, bypassing the production of an intermediate isotropic pitch. Furthermore, the presence of 25 wt.% coal in the initial slurry can increase the yield to mesophase pitch nearly twofold and yield to carbon fiber by approximately 70%. The coal extract-derived mesophase pitch was melt-spun and heat treated to produce carbon fiber with graphitic texture, high modulus (>400 GPa) and tensile strength up to 943 MPa. Overall, this work demonstrates that coal can be effectively utilized to markedly amplify the mesophase pitch and carbon fiber yield from fluid catalytic cracking decant oil by relatively simple processing, while conserving utility as a precursor to high performance carbon fiber and potentially other high value graphitic products.

36 MATERIALS SCIENCE↗