Search NASA⌕ Search

SEARCH · Search NASA

Results for “Multiple mapping conditioning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Flowing Plasma Interaction with an Electric Sail Tether Element

Electric sails are a relatively new concept for providing high speed propellant-less propulsion. Employing multiple tethers biased to high positive voltage levels (kV), electric sails are designed to gain momentum from the solar wind by repelling solar wind protons. To maximize the area of the sail that interacts with the solar wind, electric sails rely on the formation of a large plasma sheath around each small diameter tether. Motivated by interest in advancing the development of electric sails, a set of laboratory tests has been conducted to study the interaction of a drifting plasma with a sheath formed around a small diameter tether element biased at positive voltages. The laboratory test setup was created with Debye length scaling in mind to offer a path to extrapolate (via modeling) to full scale electric sail missions. Using an instrument known as a Differential Ion Flux Probe (DIFP) the interaction between a positively biased tether element and a drifting plasma has been measured for several scenarios. Clear evidence of the tether element sheath deflecting ions has been obtained. Maps of the flow angle downstream from the tether element have been made and they show the influence of the plasma sheath. Finally, electron current collection measurements have been made for a wide range of plasma conditions and tether element bias voltages. The electron collection data will have an impact on electric sail power requirements, as high voltage power supplies and electron guns will have to be sized to accommodate the electron currents collected by each tether.

Schneider, Todd↗

Physical and Chemical Conditions in the N113 Star-Forming Region in the Low-Metallicity Large Magellanic Cloud

The Large Magellanic Cloud (LMC) is the nearest (~50 kpc) star-forming galaxy characterized by a low metallicity (Z~0.3-0.5 Z⨀) similar to galaxies during the early phases of their assembly. As a result, star formation studies in the LMC provide a stepping stone to understanding star formation at earlier epochs of the universe where these processes cannot be directly observed. N113 is one of the most prominent star-forming regions in the LMC hosting one of the most massive giant molecular clouds.N113 is small enough to be imaged in its entirety, but large enough to showcase many important phenomena such as multiple generations of stars, stellar feedback, and different environments. We present our findings from an investigation of the early stages of star formation in the N113 region using the Atacama Large Millimeter/submillimeter Array (ALMA)molecular line data probing a wide density range: 12CO, 13CO, and C18O (2-1), 13COand C18O (1-0), HCN (1-0), HCO+ (1-0), H13CN (1-0) and (3-2), H13CO+ (1-0) and (3-2), CS (2-1) and (5-4), as well as 1.3 mm and 3 mm continuum. We used the Python package quick clump to identify molecular clumps. We utilized the multiline non-LTE fitting tool based on models from RADEX developed by Finn et al. (2021, ApJ, 917, 106)to construct the CO, HCN, HCO+, and CS temperature and column density, and the H2density maps of N113. We constructed a catalog of molecular clumps including their physical properties, chemical abundances, sizes, velocities, and velocity dispersions. To establish the evolutionary status of the clumps, their positions were compared with previously identified young stellar objects (YSOs) from the Spitzer/SAGE and Herschel/HERITAGE surveys, as well as water and OH masers. We compared the properties of the clumps in N113 to those in the Galaxy and other regions in the LMC to assess the impact of the environment (e.g., metallicity, stellar feedback) on the star formation process.

Jonathon Noswitz↗

Laser Materials Processing for NASA's Aerospace Structural Materials

Lasers are useful for performing operations such as joining, machining, built-up freeform fabrication, and surface treatment. Due to the multifunctional nature of a single tool and the variety of materials that can be processed, these attributes are attractive in order to support long-term missions in space. However, current laser technology also has drawbacks for space-based applications. Specifically, size, power efficiency, lack of robustness, and problems processing highly reflective materials are all concerns. With the advent of recent breakthroughs in solidstate laser (e.g., diode-pumped lasers) and fiber optic technologies, the potential to perform multiple processing techniques in space has increased significantly. A review of the historical development of lasers from their infancy to the present will be used to show how these issues may be addressed. The review will also indicate where further development is necessary to realize a laser-based materials processing capability in space. The broad utility of laser beams in synthesizing various classes of engineering materials will be illustrated using state-of-the art processing maps for select lightweight alloys typically found on spacecraft. Both short- and long-term space missions will benefit from the development of a universal laser-based tool with low power consumption, improved process flexibility, compactness (e.g., miniaturization), robustness, and automation for maximum utility with a minimum of human interaction. The potential advantages of using lasers with suitable wavelength and beam properties for future space missions to the moon, Mars and beyond will be discussed. The laser processing experiments in the present report were performed using a diode pumped, pulsed/continuous wave Nd:YAG laser (50 W max average laser power), with a 1064 nm wavelength. The processed materials included Ti-6AI-4V, Al-2219 and Al-2090. For Phase I of this project, the laser process conditions were varied and optimized to see the effects on melt-quenching, cladding/alloying (using the pre-placed powder technique), and cutting. Key parameters such laser power, pulse repetition frequency, process speed, and shield gas flow and the observed process characteristics such as plasma formation during laser/material interaction, have been reported for all experimental runs. Preliminary materials characterization of select samples was carried out using various microscopy, diffraction, spectroscopy and microhardness test methods, and reported. Select nitridation results of Ti-6AI-4V using nitrogen assist gas indicated the successful formation of hard titanium nitrides with much higher hardness (2180 kg/sq mm). A cost-effective and simple powder delivery system has been successfully fabricated for the further experimentation in Phase H.

Nagarathnam, Karthik↗

Newly Identified Climatically and Environmentally Significant High-Latitude Dust Sources

Dust particles from high latitudes have a potentially large local, regional, and global significance to climate and the environment as short-lived climate forcers, air pollutants, and nutrient sources. Identifying the locations of local dust sources and their emission, transport, and deposition processes is important for understanding the multiple impacts of high-latitude dust (HLD) on the Earth’s systems. Here, we identify, describe, and quantify the source intensity (SI) values, which show the potential of soil surfaces for dust emission scaled to values 0 to 1 concerning globally best productive sources, using the Global Sand and Dust Storms Source Base Map (G-SDS-SBM). This includes 64 HLD sources in our collection for the northern (Alaska, Canada, Denmark, Greenland, Iceland, Svalbard, Sweden, and Russia) and southern (Antarctica and Patagonia) high latitudes. Activity from most of these HLD sources shows seasonal character. It is estimated that high-latitude land areas with higher (SI ≥ 0.5), very high (SI ≥ 0.7), and the highest potential (SI ≥ 0.9) for dust emission cover > 1 670 000 km 2 , > 560 000 km 2 , and > 240 000 km 2 , respectively. In the Arctic HLD region (≥ 60◦ N), land area with SI ≥ 0.5 is 5.5 % (1 035 059 km 2 ), area with SI ≥ 0.7 is 2.3 % (440 804 km 2 ), and area with SI ≥ 0.9 is 1.1 % (208 701 km 2 ). Minimum SI values in the northern HLD region are about 3 orders of magnitude smaller, indicating that the dust sources of this region greatly depend on weather conditions. Our spatial dust source distribution analysis modeling results showed evidence supporting a northern HLD belt, defined as the area north of 50◦ N, with a “transitional HLD-source area” extending at latitudes 50–58◦ N in Eurasia and 50–55◦ N in Canada and a “cold HLD-source area” including areas north of 60◦ N in Eurasia and north of 58◦ N in Canada, with currently “no dust source” area between the HLD and low-latitude dust (LLD) dust belt, except for British Columbia. Using the global atmospheric transport model SILAM, we estimated that 1.0 % of the global dust emission originated from the high-latitude regions. About 57 % of the dust deposition in snow- and ice-covered Arctic regions was from HLD sources. In the southern HLD region, soil surface conditions are favorable for dust emission during the whole year. Climate change can cause a decrease in the duration of snow cover, retreat of glaciers, and an increase in drought, heatwave intensity, and frequency, leading to the increasing frequency of topsoil conditions favorable for dust emission, which increases the probability of dust storms. Our study provides a step forward to improve the representation of HLD in models and to monitor, quantify, and assess the environmental and climate significance of HLD.

high latitude dust↗

Flash Drought Onset and Development Mechanisms Captured With Soil Moisture and Vegetation Data Assimilation

Flash droughts evolve and intensify rapidly under the influence of anomalous atmospheric conditions. In this study, we investigate the role of assimilating remotely sensed soil moisture (SM) and vegetation properties in capturing the evolution and impacts of two flash droughts in the Northern Great Plains. We find that during 2016 drought triggered by anomalously high temperatures and excessive evaporative demands, multivariate data assimilation (DA) of MODIS-derived leaf area index (LAI) and Soil Moisture Active Passive SM within Noah-Multiparameterization model helps capture elevated transpiration at onset. Assimilation of LAI particularly helped model the resulting rapid decline in SM during onset with as high as 10.0% steeper rate of decline compared to the simulation without any assimilation. Modeled-SM anomalies exhibit a 7.5% and 11.7% increase in similarity with Evaporative Stress Index (ESI) data and U.S. Drought Monitor (USDM) maps, respectively. In contrast, during 2017 flash drought driven by record-low precipitation during summers, SM assimilation resulted in largest rates of decline in rootzone SM, as large as 48.4% compared to results from no assimilation. Multivariate DA of SM and LAI results in 6.7% and 14.3% higher spatial similarity with ESI and USDM, respectively, and is necessary to model rapid intensification caused by anomalous precipitation deficits. This study elucidates the need to incorporate multiple observational constraints from remote sensing to effectively capture rapid onset rates, intensification, and severity of flash drought following different propagation mechanisms. This is fundamental for drought early detection to provide a wider window of response and implement efficient mitigation strategies.

Shahryar K. Ahmad↗

Compositional and Microstructural Evolution of Olivine During Pulsed Laser Irradiation: Insights Based on a FIB/Field-Emission TEM Study

Introduction: The use of pulsed laser irradiation to simulate the short duration, high-energy conditions characteristic of micrometeorite impacts is now an established approach in experimental space weathering studies. The laser generates both melt and vapor deposits that contain nanophase metallic Fe (npFe(sup 0)) grains with size distributions and optical properties similar to those in natural impact-generated melt and vapor deposits. There remains uncertainty, however, about how well lasers simulate the mechanical work and internal (thermal) energy partitioning that occurs in actual impacts. We are currently engaged in making a direct comparison between the products of laser irradiation and experimental/natural hypervelocity impacts. An initial step reported here is to use analytical TEM is to attain a better understanding of how the microstructure and composition of laser deposits evolve over multiple cycles of pulsed laser irradiation. Experimental Methods: We irradiated pressed-powder pellets of San Carlos olivine (Fo(sub 90)) with up to 99 rastered pulses of a GAM ArF excimer laser. The irradiated surface of the sample were characterized by SEM imaging and areas were selected for FIB cross sectioning for TEM study using an FEI Quanta dual-beam electron/focused ion beam instrument. FIB sections were characterized using a JEOL2500SE analytical field-emission scanning transmission electron microscope (FE-STEM) optimized for quantitative element mapping at less than 10 nm spatial resolutions. Results: In the SEM the 99 pulse pressed pellet sample shows a complex, inhomogeneous, distribution of laser-generated material, largely concentrated in narrow gaps and larger depressions between grains. Local concentrations of npFe0 spherules 0.1 to 1 micrometers in size are visible within these deposits in SEM back-scatter images. Fig. 1 shows bright-field STEM images of a FIB cross-section of a one of these deposits that continuously covers the top and sloping side of an olivine grain. The deposit has 3 microstructurally distinct sub-layers composed of silicate glass with varying modal fractions and size distributions of npFe( sup 0) spherules, along with nanocrystalline silicate material. A relatively thin (50-300 nm) topmost surface layer has a high-concentration of npFe0 spherules 5-20 nm in size. Element mapping shows the layer to be enriched in Fe by a factor of 2.5 relative to the olivine substrate, with Mg and Si depleted by 20% and 10% respectively. This is compositionally complementary to the underlying, middle layer of the deposit that is depleted in Fe, enriched in Mg and has a much lower npFe0 concentration. A third layer of nanocrystalline olivine occurs at the substrate interface. Discussion: The FE-STEM results suggest the topmost layer is a vapor deposit, underlain by a thicker microstructurally complex melt-generated layer. The compositional relations suggest the melt layer was partially vaporized, preferentially losing more volatile elements (e.g., Fe). The vaporized material re-condensed to form the thin, npFe(sup 0)-rich surface deposit during or immediately after the scan cycle. Nanocrystalline olivine that grew within the melt layer as it formed and cooled is similar in volume and microstructure to what we have observed in the impact melt lining of a micrometeorite impact crater in olivine. This suggest the time-temperature relations attained in the laser sample may not be too different from a micrometeorite impact. Our TEM observations, however, do not show evidence for the same level of mechanical dam-age (e.g., fracturing) seen around the natural micrometeorite crater.

Christoffersen, R.↗

Magellan stereo images and Venusian geology

Areas of Venus imaged by Magellan radar with multiple viewing conditions provide unique data that will contribute to the solution of venusian geologic problems and provide a basis for quantitative comparison of venusian landforms with those on other planetary bodies. Three sets of images with different viewing conditions have been acquired: (1) left-looking with variable incidence angles (cycle 1 profile), (2) right-looking with nearly constant incidence angles (cycle 2 profile), and (3) left-looking with variable incidence angles that are almost always smaller than those in (1) (cycle 3 profiles). The unique data provided by paired images of the same scene with different incidence angles arises from image displacements caused by the relief of individual landforms at scales comparable to the ground-range and azimuth resolutions of the images. There are two aspects of the data: (1) Stereopsis achieved by simultaneous viewing of paired left-looking images of the same scene permits three-dimensional perception and interpretation of the morphologies of landforms at resolutions much finer than the altimetry footprints. (2) Measurements of differences of image displacements (parallax) on paired images with known imaging geometries provide quantitative estimates of the relief and shapes of landforms. The potential scientific contributions of the data can be grouped into two interrelated classes: (A) geologic mapping, analysis, and interpretation and (B) topical studies that involve topographic measurements. Stereopsis, without quantitative measurements, enhances geologic mapping, analysis, and interpretation of the rock units of Venus to a degree that cannot be overestimated. In geologic mapping, assemblages of landforms, assessments of backscatter and variations in backscatter, and fine-scale topography are used to define and characterize geologic map units that represent laterally continuous deposits or rock units. Stereopsis adds the important dimension of local relief for characterization of geologic units at a scale that is not possible with Magellan altimetry or products derived from the altimetry. Relative ages of the geologic units are determined using the well-known principles of superposition and intersection. Here, the perception of relief is invaluable because superposition relations among the geological units are more readily and clearly established. The recognition of folds, faults, and fault systems, regardless of their orientations, is facilitated with stereopsis so that sequences of deformation of the geologic units can be determined and structural analyses vastly improved. Shapes of landforms are readily perceived so that they can be properly interpreted. The end result of the mapping, analyses, and interpretations is a geologic history of Venus that includes the sequences of formation and deformation of various geologic units. Measurements of relief at the finest scale possible are necessary for numerous topical studies. Standard altimetry will provide the necessary information on the relief of most large landforms, but it tends to underestimate the relief of small landforms and distorts their shapes. Although special processing of the altimeter echoes improves the estimates of the relief and shapes of some landforms, there are uncertainties in the interpretations of the echoes. Examples of topical studies requiring measurements of relief are given.

Moore, H. J.↗

Control of the NASA Langley 16-Foot Transonic Tunnel with the Self-Organizing Feature Map

A predictive, multiple model control strategy is developed based on an ensemble of local linear models of the nonlinear system dynamics for a transonic wind tunnel. The local linear models are estimated directly from the weights of a Self Organizing Feature Map (SOFM). Local linear modeling of nonlinear autonomous systems with the SOFM is extended to a control framework where the modeled system is nonautonomous, driven by an exogenous input. This extension to a control framework is based on the consideration of a finite number of subregions in the control space. Multiple self organizing feature maps collectively model the global response of the wind tunnel to a finite set of representative prototype controls. These prototype controls partition the control space and incorporate experimental knowledge gained from decades of operation. Each SOFM models the combination of the tunnel with one of the representative controls, over the entire range of operation. The SOFM based linear models are used to predict the tunnel response to a larger family of control sequences which are clustered on the representative prototypes. The control sequence which corresponds to the prediction that best satisfies the requirements on the system output is applied as the external driving signal. Each SOFM provides a codebook representation of the tunnel dynamics corresponding to a prototype control. Different dynamic regimes are organized into topological neighborhoods where the adjacent entries in the codebook represent the minimization of a similarity metric which is the essence of the self organizing feature of the map. Thus, the SOFM is additionally employed to identify the local dynamical regime, and consequently implements a switching scheme than selects the best available model for the applied control. Experimental results of controlling the wind tunnel, with the proposed method, during operational runs where strict research requirements on the control of the Mach number were met, are presented. Comparison to similar runs under the same conditions with the tunnel controlled by either the existing controller or an expert operator indicate the superiority of the method.

Motter, Mark A.↗

Explanation Constraint Programming for Model-based Diagnosis of Engineered Systems

We can expect to see an increase in the deployment of unmanned air and land vehicles for autonomous exploration of space. In order to maintain autonomous control of such systems, it is essential to track the current state of the system. When the system includes safety-critical components, failures or faults in the system must be diagnosed as quickly as possible, and their effects compensated for so that control and safety are maintained under a variety of fault conditions. The Livingstone fault diagnosis and recovery kernel and its temporal extension L2 are examples of model-based reasoning engines for health management. Livingstone has been shown to be effective, it is in demand, and it is being further developed. It was part of the successful Remote Agent demonstration on Deep Space One in 1999. It has been and is being utilized by several projects involving groups from various NASA centers, including the In Situ Propellant Production (ISPP) simulation at Kennedy Space Center, the X-34 and X-37 experimental reusable launch vehicle missions, Techsat-21, and advanced life support projects. Model-based and consistency-based diagnostic systems like Livingstone work only with discrete and finite domain models. When quantitative and continuous behaviors are involved, these are abstracted to discrete form using some mapping. This mapping from the quantitative domain to the qualitative domain is sometimes very involved and requires the design of highly sophisticated and complex monitors. We propose a diagnostic methodology that deals directly with quantitative models and behaviors, thereby mitigating the need for these sophisticated mappings. Our work brings together ideas from model-based diagnosis systems like Livingstone and concurrent constraint programming concepts. The system uses explanations derived from the propagation of quantitative constraints to generate conflicts. Fast conflict generation algorithms are used to generate and maintain multiple candidates whose consistency can be tracked across multiple time steps.

Narasimhan, Sriram↗

LADEE Preparations for Contingency Operations for the Lunar Orbit Insertion Maneuver

The Lunar Atmosphere and Dust Environment Explorer (LADEE) spacecraft was launched on September 6, 2013, and completed its mission on April 17, 2014 with a directed impact to the Lunar Surface. Its primary goals were to examine the lunar atmosphere, measure lunar dust, and to demonstrate high rate laser communications. The LADEE mission was a resounding success, achieving all mission objectives, much of which can be attributed to careful planning and preparation. This paper discusses the specific preparations for fault conditions that could occur during a highly-critical phase of the mission. To get to the Moon, the spacecraft traversed multiple phasing loops around the Earth, and then executed a breaking maneuver to achieve lunar orbit. This Lunar Orbit Insertion (LOI) maneuver was perhaps the most time-critical phase of the entire mission. The LOI maneuver had to occur within a twenty minute window in order to achieve lunar orbit with an acceptable amount of propellant remaining. Missing this window would have likely resulted in a loss of the entire mission. An additional challenge of the maneuver was that spacecraft was out of view for approximately one hour prior to the main thruster burn, with the burn needing to occur within five minutes after coming into view. These conditions resulted in unique challenges for ground operations and the fault management system. Early in the planning stages of the mission, the criticality and challenges of this maneuver were evident to the system designers. The major concern was that any triggering of the on-board fault management system, whether it is in response to a true fault or a false positive, would result in an unacceptable delay to the burn. Therefore the flight software was designed with a flexible fault management system, such that any or all of the fault management responses could be disabled for the lead up and execution of the maneuver. Later, a triage was conducted to develop a list of fault responses, mapped to various parts of the timeline of the maneuver. Some of these contingency responses were solely ground-based if the time to detect, diagnose, and respond were adequate. Other responses were automated on-board if the response time from the ground would have been inadequate. For instance, in order to recover from a system reboot, on-board automation would have automatically reconfigured the spacecraft for the burn and reoriented the spacecraft to the burn attitude.These contingency responses were practiced, over and over, during numerous rehearsals. Although the LOI maneuver was executed without having to use any of these contingencies, the LADEE team was adequately prepared for this highly critical phase of the mission.

Cannon, Howard↗

VIPER – Volatiles Investigating Polar Exploration Rover: Mission Overview

VIPER is a low cost, lunar volatiles detection and measurement mission that will be delivered to the lunar south pole by one of NASA’s Commercial Lunar Payload Services partners and will characterize the nature of the volatiles in the area and extrapolate this data to create global lunar water resource maps. It will be the first mining expedition on another world while simultaneously addressing fundamental planetary science questions. Prospecting for lunar water at the poles is the next step in understanding the resource potential and addressing key theories about water emplacement and retention. It now appears that potentially economically significant amounts of water ice exists at the poles of the Moon, however, the distribution of this water is still not understood at a level sufficient to fully evaluate economic models. The water ice (and other potential volatiles), the “ore body”, needs to be understood at the scales of 10s to 100s of meters to evaluate localization, extraction and processing techniques. To accomplish this, VIPER will survey permanently-shadowed regions, semi-permanent shadowed regions, and even semi and full sunlit areas in order to have a comprehensive survey of polar region volatiles, to best inform future mission architectures. In order to characterize the volatiles, a payload suite consisting of a neutron spectrometer, mass spectrometer, near infrared spectrometer and a 1-meter drill will be hosted on the VIPER mobile lunar rover platform. Since VIPER is a relatively low cost, schedule-constrained, risk-tolerant mission, there are architectural limitations that require unique mission planning constraints to enable exploration of the lunar south pole region. These regions offer unique challenges such as uncertain terrain conditions, rock and crater hazards, lunar dust, multipath communications effects, extreme thermal environments and multiple overlapping planning constraints. Mission design/traverse planning, system design capabilities and mission operations are all highly linked through initial development phases. We will describe the current mission overview and the unique approaches taken by the VIPER project based on our programmatic framework and unique mission environment.

VIPER↗

Implementation Concept of Operation for a Multi-Purpose Cassegrain Solar Concentrator, Micro-Spectrometers, and Electrostatic Neutralizers to Enable In Situ Construction Activities plus Lunar, Planetary, and Deep Space Science Exploration on the Moon

The ability to utilize regolith would support human missions to the Moon and Mars by both stabilizing the surface as well as the use of indigenous resources. Precision landing requirements include surface stabilization to prevent damage or contamination due to regolith projectiles as a result of plume interaction with regolith. The use of indigenous resources rather than hauling materials from Earth appears to be economically a palatable option by converting indigenous resources to usable products. However, such activities have new technical challenges to overcome the issues related to lunar environmental conditions, a wide range of temperature fluctuation, extremely high vacuum, and electrostatically charged fine regolith dusts. For both the regolith sintering and extraction of resources onsite, a Cassegrain solar concentrator was studied for not only sintering lunar regolith into a hardened stabilized surface, but also other multiple applications. This report illustrates a Cassegrain solar concentrator that has multi-functional capabilities for space missions. Proper design and implementation of high-performance lightweight composite materials for the primary mirror of the Cassegrain concentrator can offer multiple capabilities to be performed on the Moon. The multiple applications studied with Cassegrain concentrators are (1) Solar sintering for landing pad and habitats, (2) Harvest of volatiles: H2O, O2, H2, and He-3, (3) Space antenna for telemetry and telecommunication, and (4) Space telescope with 20-meter aperture that exceeds the space telescopes to date in terms of the State-of-Art (SOA) in resolution and aperture diameter. In this study, a key emphasis was placed on the NASA Langley-developed boron nitride nanotube (BNNT) nanocomposite technology which is ideal for the segmented primary mirror structure of the Cassegrain system because it promises a very low coefficient of thermal expansion (CTE) and negligible Poisson ratio. Also, BNNT nanocomposites offer several noticeable benefits, such as light weight, radiation shielding capability, and mechanical strength for structural applications. Additionally, the NASA Langley-developed bullet-like micro-spectrometer and electrostatic power generator were reviewed for mineral mapping applications and electrostatic power generation and dust mitigation from electrostatically charged regolith.

landing pad↗

Kepler Planet Detection Metrics: Per-Target Flux-Level Transit Injection Tests of TPS for Data Release 25

Quantifying the ability of a transiting planet survey to recover transit signals has commonly been accomplished through Monte-Carlo injection of transit signals into the observed data and subsequent running of the signal search algorithm (Gilliland et al., 2000; Weldrake et al., 2005; Burke et al., 2006). In order to characterize the performance of the Kepler pipeline (Twicken et al., 2016; Jenkins et al., 2017) on a sample of over 200,000 stars, two complementary injection and recovery tests are utilized:1. Injection of a single transit signal per target into the image or pixel-level data, hereafter referred to as pixel-level transit injection (PLTI), with subsequent processing through the Photometric Analysis (PA), Presearch Data Conditioning (PDC), Transiting Planet Search (TPS), and Data Validation (DV) modules of the Kepler pipeline. The PLTI quantification of the Kepler pipeline's completeness has been described previously by Christiansen et al. (2015, 2016); the completeness of the final SOC 9.3 Kepler pipeline acting on the Data Release 25 (DR25) light curves is described by Christiansen (2017).2. Injection of multiple transit signals per target into the normalized flux time series data with a subsequent transit search using a stream-lined version of the Transiting Planet Search (TPS) module. This test, hereafter referred to as flux-level transit injection (FLTI), is the subject of this document. By running a heavily modified version of TPS, FLTI is able to perform many injections on selected targets and determine in some detail which injected signals are recoverable. Significant numerical efficiency gains are enabled by precomputing the data conditioning steps at the onset of TPS and limiting the search parameter space (i.e., orbital period, transit duration, and ephemeris zero-point) to a small region around each injected transit signal.The PLTI test has the advantage that it follows transit signals through all processing steps of the Kepler pipeline, and the recovered signals can be further classified as planet candidates or false positives in the exact same manner as detections from the nominal (i.e., observed) pipeline run (Twicken et al., 2016, Thompson et al., in preparation). To date, the PLTI test has been the standard means of measuring pipeline completeness averaged over large samples of targets (Christiansen et al., 2015, 2016; Christiansen, 2017). However, since the PLTI test uses only one injection per target, it does not elucidate individual-target variations in pipeline completeness due to differences in stellar properties or astrophysical variability. Thus, we developed the FLTI test to provide a numerically efficient way to fully map individual targets and explore the performance of the pipeline in greater detail. The FLTI tests thereby allow a thorough validation of the pipeline completeness models (such as window function (Burke and Catanzarite, 2017a), detection efficiency (Burke Catanzarite, 2017b), etc.) across the spectrum of Kepler targets (i.e., various astrophysical phenomena and differences in instrumental noise). Tests during development of the FLTI capability revealed that there are significant target-to-target variations in the detection efficiency.

DR25↗

Hail Storm Risk Assessment Using Space-Borne Remote Sensing Observations and Reanalyses

Much of the world is impacted by severe thunderstorms, but whether they become disasters depends upon resilience--our capacity to prepare, mitigate, respond, and recover. Hail is the costliest severe weather hazard for the insurance industry, generating ~70% of severe convective storm losses due to damage to assets such as homes, businesses, agriculture, and infrastructure. Most insurance companies do not reserve enough capital to cover catastrophes, so they acquire reinsurance. The reinsurance industry uses catastrophe models (CatModels) to statistically estimate risk to an insurer’s portfolio. Hail CatModels are developed with climatologies that define hailstorm frequency and severity. Hail-prone areas can be defined using hail reports from trained spotters, the media, and the general public. Extremely severe hail (2+ inch diameter) occurs nearly every day across the world. Weather radars can detect hail because hailstones strongly reflect microwave signals that they emit. However, hail climatologies are difficult to derive because hail covers small areas and there are neither hail reporting mechanisms (e.g. website or mobile app) nor radar networks in most places outside the US and Europe. This lack of ground truth on severe hail puts society and economies at risk. Hail is generated within storms by strong updrafts. These updrafts exhibit unique signatures in NASA and other agency satellite observations, offering new opportunities for hailstorm analysis. Geostationary (GEO) visible and infrared imagery has been collected for ~15-25 years across the world (region dependent) and methods have been developed at NASA Langley Research Center (LaRC) to detect hailstorm updrafts using GEO imagery. Climatological GEO updraft data has been used by Willis Towers Watson (WTW), a leader in catastrophe risk assessment for the insurance industry, and Karlsruhe Institute of Technology to develop CatModels over Europe and Australia. Hail can also be inferred with passive microwave imagery collected by low-Earth-orbiting sensors such as the GPM GMI, TRMM TMI, AMSR-E, AMSR-2, SSM/I, and SSMIS over the last 20+ years using methods developed at the Marshall Space Flight Center (MSFC). Hailstorms generate enhanced lightning flash rates that can be tracked using new GOES-R series GEO Lightning Mapping (GLM) imagery. Atmospheric reanalyses can be used to define favorable hailstorm environments for combination with the satellite-based storm detections. This presentation will describe a framework for developing continental to global hail climatologies and CatModels based on NASA satellite data and capabilities. This is a collaboration between LaRC and MSFC, WTW, and partners in Brazil, Argentina, and South Africa. This project seeks to mitigate hail disasters by aiding development of new satellite-based severe storm nowcasting tools by regional partners and developing climatologies to improve societal understanding of hail frequency. GEOO visible and infrared metrics of storm intensity, environmental conditions based on reanalyses, spotter hail reports and radar MESH observations are intercompared to quantify the detectability of hailstorms, and our ability to discriminate hailstorms from other severe storms. We are also maturing methods using land surface imaging satellite data (e.g. MODIS, Landsat, Sentinel 1 and 2) to identify hail damage to agriculture. Work with WTW will improve socioeconomic resilience through development of new CatModels. Southern Brazil, Uruguay, Paraguay, and Argentina feature some of the most intense thunderstorms on Earth. South America and South Africa are developing insurance markets of interest to WTW clients, and is similar to other regions routinely impacted by hail that do not have comprehensive hail reporting or radars to assess hailstorm frequency. Project datasets will be made available via online GIS-enabled tools developed at the LaRC Atmospheric Science Data Center (ASDC) which will visualize data and provide it in multiple formats for use in a wide range of open source and commercial tools.

Kristopher Michael Bedka↗

Environmental Snapshots for Satellite Multi-Angle Aerosol Retrieval Validation During the ACE-Asia Field Campaign

On five occasions spanning the ACE-Asia field experiment in spring 2001, the multi-angle imaging MISR instrument, flying aboard the NASA Earth Observing System s Terra satellite, took quarter-kilometer data over a 400-km-wide swath, coincident with high-quality observations by multiple instruments on two or more participating surface and airborne platforms. The cases capture a range of clean, polluted, and dusty aerosol conditions. They represent some of the best opportunities during ACE- Asia for comparative studies among intensive and extensive aerosol observations in their environmental context. We inter-compare related measurements and discuss the implications of apparent discrepancies for each case, at a level of detail appropriate to the analysis of satellite observations. With a three-stage optical modeling process, we synthesize data from multiple sources into layer-by-layer snapshots that summarize what we know about the state of the atmosphere and surface at key locations during each event, to be used for satellite vicarious calibration and aerosol retrieval validation. Aerosols within a few kilometers of the surface were composed primarily of pollution and Asian dust mixtures, as expected. Accumulation and coarse-mode particle size distributions varied little among the events studied, but column aerosol optical depth changed by more than a factor of four, and the near-surface proportion of dust ranged from about 25% to 50%. The amount of absorbing material in the sub-micron fraction was highest when near-surface winds crossed Beijing and the Korean Peninsula, and was considerably lower for all other cases. Ambiguities remain in segregating size distributions by composition; having simultaneous single scattering albedo measurements at more than a single wavelength would significantly reduce the resulting optical model uncertainties, as would integral constraints from surface and atmospheric radiative flux observations. The consistency of component particle micro-physical properties among the five events, even in this relatively complex aerosol environment, suggests that global, satellite-derived maps of aerosol-air-mass-type extent, combined with targeted in situ measurements, can provide a detailed global picture of aerosol behavior. Further joint satellite and in situ analysis is needed to assess the spatial variability of both intensive and extensive aerosol properties within aerosol air masses in two spatial dimensions.

Kahn, Ralph↗

SSME Condition Monitoring Using Neural Networks and Plume Spectral Signatures

For a variety of reasons, condition monitoring of the Space Shuttle Main Engine (SSME) has become an important concern for both ground tests and in-flight operation. The complexities of the SSME suggest that active, real-time condition monitoring should be performed to avoid large-scale or catastrophic failure of the engine. In 1986, the SSME became the subject of a plume emission spectroscopy project at NASA's Marshall Space Flight Center (MSFC). Since then, plume emission spectroscopy has recorded many nominal tests and the qualitative spectral features of the SSME plume are now well established. Significant discoveries made with both wide-band and narrow-band plume emission spectroscopy systems led MSFC to develop the Optical Plume Anomaly Detection (OPAD) system. The OPAD system is designed to provide condition monitoring of the SSME during ground-level testing. The operational health of the engine is achieved through the acquisition of spectrally resolved plume emissions and the subsequent identification of abnormal emission levels in the plume indicative of engine erosion or component failure. Eventually, OPAD, or a derivative of the technology, could find its way on to an actual space vehicle and provide in-flight engine condition monitoring. This technology step, however, will require miniaturized hardware capable of processing plume spectral data in real-time. An objective of OPAD condition monitoring is to determine how much of an element is present in the SSME plume. The basic premise is that by knowing the element and its concentration, this could be related back to the health of components within the engine. For example, an abnormal amount of silver in the plume might signify increased wear or deterioration of a particular bearing in the engine. Once an anomaly is identified, the engine could be shut down before catastrophic failure occurs. Currently, element concentrations in the plume are determined iteratively with the help of a non-linear computer code called SPECTRA, developed at the USAF Arnold Engineering Development Center. Ostensibly, the code produces intensity versus wavelength plots (i.e., spectra) when inputs such as element concentrations, reaction temperature, and reaction pressure are provided. However, in order to provide a higher-level analysis, element concentration is not specified explicitly as an input. Instead, two quantum variables, number density and broadening parameter, are used. Past experience with OPAD data analysis has revealed that the region of primary interest in any SSME plume spectrum lies in the wavelength band of 3300 A to 4330 A. Experience has also revealed that some elements, such as iron, cobalt and nickel, cause multiple peaks over the chosen wavelength range whereas other elements (magnesium, for example) have a few, relatively isolated peaks in the chosen wavelength range. Iteration with SPECTRA as a part of OPAD data analysis is an incredibly labor intensive task and not one to be performed by hand. What is really needed is the "inverse" of the computer code but the mathematical model for the inverse mapping is tenuous at best. However, building generalized models based upon known input/output mappings while ignoring details of the governing physical model is possible using neural networks. Thus the objective of the research project described herein was to quickly and accurately predict combustion temperature and element concentrations (i.e., number density and broadening parameter) from a given spectrum using a neural network. In other words, a neural network had to be developed that would provide a generalized "inverse" of the computer code SPECTRA.

Hopkins, Randall↗

Improving Access to the GEOS Composition Forecast Model with API Development and Ingestion into Google Earth Engine

The GEOS Composition Forecast (GEOS-CF) model produces forecast and historical estimates of atmospheric composition and meteorology fields, which provide useful insight into air quality issues and events. In a year for which Canadian wildfires created adverse air quality conditions in the eastern United States, access to model fields such as PM2.5 are in high demand. The GEOS-CF team at the NASA Global Modeling and Assimilation Office (GMAO) first developed in-house solutions to improve data access via the CF API, and recently partnered with Google to ingest a collated set of model diagnostics into the Google Earth Engine (GEE) data repository. GEOS-CF model output is also being ingested into AWS storage. Creating these various open access points to GEOS-CF model diagnostics provides the public with an opportunity to easily interact with air quality information. Users are able to use a temporally consistent global grid of air quality fields in machine learning applications, mapping tools, and data informatics. Hosting GEOS-CF forecasts and the historical timeseries of these chemistry and meteorology fields in GEE allows users to create dynamic JavaScript-based air quality applications in the GEE code editor. GEOS-CF users can also access the model output via the GEE Python application programming interface (API), making it easy to perform various analyses with Python. This presentation will show two examples of accessing the GEOS-CF model through GEE. The first is an example application made in the GEE code editor which allows users to view time series plots and downscaled maps of surface level NO2. The second example exhibits using the GEE Python API to create a machine learning model to temporally gap-fill between air quality observations. These examples are an introduction to the many possible benefits of having open access to the GEOS-CF model through multiple platforms.

Callum Wayman↗

Improving Access to the GEOS Composition Forecast Model with API Development and Ingestion into Google Earth Engine

The GEOS Composition Forecast (GEOS-CF) model produces forecast and historical estimates of atmospheric composition and meteorology fields, which provide useful insight into air quality issues and events. In a year for which Canadian wildfires created adverse air quality conditions in the eastern United States, access to model fields such as PM2.5 are in high demand. The GEOS-CF team at the NASA Global Modeling and Assimilation Office (GMAO) first developed in-house solutions to improve data access via the CF API, and recently partnered with Google to ingest a collated set of model diagnostics into the Google Earth Engine (GEE) data repository. GEOS-CF model output is also being ingested into AWS storage. Creating these various open access points to GEOS-CF model diagnostics provides the public with an opportunity to easily interact with air quality information. Users are able to use a temporally consistent global grid of air quality fields in machine learning applications, mapping tools, and data informatics. Hosting GEOS-CF forecasts and the historical timeseries of these chemistry and meteorology fields in GEE allows users to create dynamic JavaScript-based air quality applications in the GEE code editor. GEOS-CF users can also access the model output via the GEE Python application programming interface (API), making it easy to perform various analyses with Python. This presentation will show two examples of accessing the GEOS-CF model through GEE. The first is an example application made in the GEE code editor which allows users to view time series plots and downscaled maps of surface level NO 2 . The second example exhibits using the GEE Python API to create a machine learning model to temporally gap-fill between air quality observations. These examples are an introduction to the many possible benefits of having open access to the GEOS-CF model through multiple platforms.

Callum Wayman↗