SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The NACA CYH airfoil section is described and its aerodynamic characteristics are given as tested in the NACA variable density wind tunnel at twenty atmosphere pressure. This section has a low drag, a high maximum lift, and a small travel of center of pressure.
Tests were made in the NACA tank and in the NACA 7 by 10 foot wind tunnel on two models of transverse step floats and three models of pointed step floats considered to be suitable for use with single float seaplanes. The object of the program was the reduction of water resistance and spray of single float seaplanes without reducing the angle of dead rise believed to be necessary for the satisfactory absorption of the shock loads. The results indicated that all the models have less resistance and spray than the model of the Mark V float and that the pointed step floats are somewhat superior to the transverse step floats in these respects. Models 41-D, 61-A, and 73 were tested by the general method over a wide range of loads and speeds. The results are presented in the form of curves and charts for use in design calculations.
An investigation has been made in the NACA 7- by 10-foot wind tunnel of a large chord NACA 23021 airfoil equipped with two arrangements of a completely extended 15 percent chord extensible flap. One of the flaps had a faired juncture, without a gap; the other was provided with a slot between the trailing edge of the airfoil and the nose of the flap. The results showed that the basic airfoil gave the lowest profile-drag coefficients over the low lift range, the airfoil with the plain extensible flap gave the lowest profile-drag coefficients over the moderate lift range, and the airfoil with the slotted extensible flap gave the lowest profile-drag coefficients over the high lift range. The airfoil with the slotted extensible flap had the same maximum lift at a flap deflection of 25 degrees as the airfoil with the plain extensible flap had at a flap deflection of 60 degrees. The results of comparisons of the airfoil pitching-moment coefficients obtained with the two types of flap are dependent upon the basis chosen for comparison. Complete aerodynamic section characteristics are presented for the various flap deflections for both flap arrangements in the completely extended portion.
Pressure-distribution tests of an NACA 0009 airfoil with an 80-percent-chord plain flap and three plain tabs, having chord of 10, 20, and 30 percent of the flap chord, were made. Section data suitable for application to the design of horizontal and vertical tail surfaces were obtained. Resultant-pressure diagrams for the airfoil with the flap and the 20-percent-chord tab are presented. Plots are also given of increments of normal-force and hinge-moment coefficients for the airfoil, the flap, and the three tabs. A comparison of some characteristic slopes for the 30-, the 50-, and the 80-percent-chord flaps, tested in the general investigation of plain flaps for control surfaces, is included. Section aerodynamic and load data have been made available for a wide range of flap and a tab chords to be used on an NACA 0009 airfoil or on other conventional sections.
A general description of the field operations of the U.S. Weather Bureau thunderstorm project conducted in the vicinity of Orlando, Florida during the summer month of 1946 is given. The participation of NACA in this project is described and measurements of atmospheric turbulence taken by NACA are presented for one of the flights. The results indicate that some regions of thunderstorms may present no great hazard to flight, while exceptionally severe conditions of atmospheric turbulence may occur in other regions, or even in the same region, at about the same time. The results also indicate that these severe conditions of turbulence might lead to loss of control with the possible loss of the airplane.
The NACA mixture analyzer was developed as a research instrument for the continuous indication of fuel-air ratios of aircraft engine installations throughout the range of engine operation. It has been evaluated by using it to measure the mixture distribution of a nine-cylinder radial aircraft engine in flight. The mixture distribution among the cylinders in flight was obtained at normal operating conditions for the engine at an altitude of 5000 feet. Some limited data was also obtained at an altitude of 20,000 feet. Results of these flight tests showed that the NACA mixture analyzer is a satisfactory and dependable instrument for continuous indication of the mixture in flight at all engine conditions regardless of altitude and temperature.
A helicopter rotor employing an NACA 8-H-12 airfoil section has been tested on the Langley helicopter test tower. Two blade surface conditions were investigated, first with a filled blade which was within 0.002 inch of true airfoil shape obtained by use of plastic filler, and second with the filler removed resulting in a surface condition within 0.020 inch of true airfoil shape. Tests were conducted for the two sur-face conditions at a tip speed of 455 feet per second and over a tip-speed range from 455 to 650 feet per second for the blades with filler removed. The NACA 8-H-12 blades with the filled surface showed an aver-age reduction of 6 to 7 percent in total torque coefficients.
At the suggestion of the Subcommittee on Internal Flow, the National Advisory Committee for Aeronautics has assembled this bibliography on air inlet and internal flow data for aircraft. It was felt that the purpose of this publication, to furnish the engineer and researcher with a listing of theoretical and experimental studies related directly and indirectly to the field of internal flows, could be served best by presenting some of the more pertinent and interesting references. Thus this bibliography is not complete in its listing of internal flow reports from the NACA or from other sources. The works referenced here are, for the most part, those published before January 1948. To aid the investigator in finding references, the bibliography has been indexed according to subject matter. NACA reports and reports from other sources are grouped separately. The subject breakdown used may be found in the table of contents on the preceding pages.
Measurements of the distribution of surface pressures were made on two wing-body combinations employing a triangular wing having an aspect ratio ratio of 2. The first of these combinations had a wing with the NACA 0008-63 section parallel to the air stream while the wing of the second had the NACA 0005-63 section in the stream direction. The measurements were made for Mach numbers from 0.11 to 0.95 at a constant Reynolds number of 3.0 million. Data were also obtained for Reynolds numbers up to 15.0 million at the lower Mach number. A summary of data obtained from previously published force tests of these same models is also included for completeness of the presentation of the effect of wing thickness.
The NACA model 40 series of flying-boat hull models consists of 2 forebodies and 3 afterbodies combined to provide several forms suitable for use in small marine aircraft. One forebody is the usual form with hollow bow sections and the other has a bottom surface that is completely developable from bow to step. The afterbodies include a short pointed afterbody with an extension for the tail surfaces, a long afterbody similar to that of a seaplane float but long enough to carry the tail surfaces, and a third obtained by fitting a second step in the latter afterbody. The various combinations were tested in the NACA Tank by the general method over a suitable range of loadings. Fixed-trim tests were made for all speeds likely to be used and free-to-trim tests were made at low speeds to slightly beyond the hump speed. The characteristics of the hulls at best trim angles have been deduced from the data of the tests at fixed trim angles and are given in the form of nondimensional coefficients applicable to any size hull.
Report presents the results of drag and pressure tests of spheres having diameters of 2, 4, 6, 8, 10, and 12 inches in eight NACA wind tunnels, in the air ahead of the carriage in the NACA tank, and beneath an autogiro in flight .
For the purpose of studying the transition from laminar to turbulent flow, boundary-layer measurements were made in the NACA full-scale wind tunnel on three symmetrical airfoils of NACA 0009, 0012, and 0018 sections. The effects of variations in lift coefficient, Reynolds number, and airfoil thickness on transition were investigated. Air speed in the boundary layer was measured by total-head tubes and by hot wires; a comparison of transition as indicated by the two techniques was obtained. The results indicate no unique value of Reynolds number for the transition, whether the Reynolds number is based upon the distance along the chord or upon the thickness of the boundary layer at the transition point. In general, the transition is not abrupt and occurs in a region that varies in length as a function of the test conditions.
Report presents the results of an investigation made in the NACA 7 by 10-foot wind tunnel of large-chord NACA and 23021, and 23030 airfoils with split flaps 10, 20, 30, and 40 percent of the wing chord to determine the section aerodynamic characteristics of the airfoils as affected by airfoil thickness, flap chord, and flap deflection. The complete section aerodynamic characteristics of all the combinations tested are given in the form of graphs of lift, drag, and pitching-moment coefficients, and certain applications to aerodynamic design are discussed.
Report presents the results of an investigation made in the NACA 7 by 10-foot wind tunnel of a large-chord NACA 23012 airfoil with several arrangements of venetian-blind flaps to determine the aerodynamic section characteristics as affected by the over-all flap chord, the chords of the slats used to form the flap, the slat spacing, the number of slats and the position of the flap with respect to the wing. Complete section data are given in the form of graphs for all the combinations tested.
Report presents the results of an investigation conducted in the NACA 7 by 10-foot win tunnel to determine the effect of the deflection of main and auxiliary slotted flaps on the aerodynamic section characteristics of large-chord NACA 23012, 23021, 23030 airfoils equipped with 40-percent-chord double slotted flaps. The complete aerodynamic section characteristics and envelope polar curves are given for each airfoil-flap combination. The effect of airfoil thickness is shown, and comparisons are made of single slotted flaps with double slotted flaps on each of the airfoils.
Report presents the results of a study of combustion in a spark-ignition engine given in NACA Technical Reports 704 and 727. The present investigation was made with the NACA high-speed motion-picture camera, operating at 40,000 photographs a second, and with a cathode-ray oscillograph operating on a piezoelectric pick-up in the combustion chamber. Photographs are presented showing that the origin of knock is not necessarily in the end gas. The data obtained indicates that knock takes place only in a part of the cylinder charge which has been previously ignited either by autoignition or by the passage of the flame fronts but which has not burned to completion. Mottled regions in the high-speed Schlieren photographs are demonstrated to represent combustion regions.
Results of flight tests of the performance and cooling characteristics of three NACA D cowlings and of a conventional NACA D cowling on the XP-42 airplane are summarized and compared. The D cowling is, in general, characterized by the use of an annular inlet and diffuser section for the engine-cooling air. The D cowlings tested were a long-nose high-inlet-velocity cowling, a short-nose high-inlet-velocity cowling, and a short-nose low inlet-velocity cowling. The use of wide-chord propeller cuffs or an axial-flow fan with the D cowlings increased the cooling pressure recoveries in the climb condition at the expense of some of the improvement in speed.
The NACA injection impeller was developed to improve the mixture distribution of aircraft engines by discharging the fuel from a centrifugal supercharger impeller and thus to promote a thorough mixing of fuel and charge air. Experiments with a double-row radial aircraft engine indicated that for the normal range of engine power the NACA injection impeller provided marked improvement in mixture distribution over the standard spray-bar injection system used in the same engine. The mixture distribution at cruising conditions was excellent; at 1200, 1500, and 1700 brake horsepower, the differences between the fuel-air ratios of the richest and the leanest cylinders were reduced to approximately one-third their former values.