Search NASA⌕ Search

SEARCH · Search NASA

Results for “NANOSTRUCTURES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

High-efficiency solar thermophotovoltaic system using a nanostructure-based selective emitter

Herein, we present the design, fabrication, optimization, and experimental results of a high-efficiency planar solar thermophotovoltaic (STPV) system utilizing a micro-textured absorber and a nanostructure multilayer metal-dielectric coated selective emitter fabricated on a tungsten (W) substrate. Light absorptance of more than 90% was achieved at visible and near-infrared wavelengths using the microtextured absorbing surface. The nanostructure selective emitter consists of two thin-film optical coatings of silicon nitride (Si3N4) and a layer of W in between to increase the surface emissivity in spectral regimes matching the quantum efficiency of the thermophotovoltaic (TPV) cells. Gallium antimonide (GaSb)-based TPV cells are used in our STPV design. The experiment was conducted at different operating temperatures using a high-power continuous wave laser diode stack as a simulated source of concentrated incident radiation. Our experimental setup measured a maximum electrical output power density of 1.71 W/cm 2 at 1676 K STPV temperature, and the overall power conversion efficiency of 8.4% after normalizing the output power density to the emitter area. This is the highest STPV system efficiency reported so far for any experimental STPV device. The incident optical laser power on the absorber side was 131 W. This is equivalent to a solar concentration factor of ~2100, which is within the practical limit and readily achievable with Fresnel lens setup.

14 SOLAR ENERGY↗
DOE OSTI2020

Wet-chemical etching of FIB lift-out TEM lamellae for damage-free analysis of 3-D nanostructures

Reducing ion beam damage from the focused ion beam (FIB) during fabrication of cross sections is a well-known challenge for materials characterization, especially cross sectional characterization of nanostructures. To address this, a new method has been developed for cross section fabrication enabling high resolution transmission electron microscopy (TEM) analysis of 3-D nanostructures free of surrounding material and free of damage detectable by TEM analysis. Before FIB processing, nanopillars are encapsulated in a sacrificial oxide which acts as a protective layer during FIB milling. Furthermore, the cross sectional TEM lamella containing the nanopillars is then mounted and thinned with some modifications to conventional FIB sample preparation that provide stability for the lamella during the following wet-chemical dip etch. The wet-chemical etch of the TEM lamella removes the sacrificial oxide layer, freeing the nanopillars from any material that would obscure TEM imaging. Both high resolution TEM and aberration corrected scanning TEM images of Si/SiGe pillars with diameters down to 30 nm demonstrate the successful application of this approach.

3-d nanostructure analysis↗
DOE OSTI2023

Chiral Spectroscopy of Nanostructures

Chirality is ubiquitous in the universe and in living creatures over detectable length scales from the subatomic to the galactic, as exemplified in the two extremes by subatomic particles (neutrinos) and spiral galaxies. Between them are living creatures that display multiple levels of chirality emerging from hierarchically assembled asymmetric building blocks. Not too far from the bottom of this pyramid are the foundational building blocks with chiral atomic centers on sp 3 carbon atoms exemplified by L-amino acids and D-sugars that are self-assembled into higher-order structures with increasing dimensions forming highly complex, amazingly functional, and energy-efficient living systems. The organization and materials employed in their construction inspired scientists to replicate complex living systems via the self-assembly of chiral components. Multiple studies pointed to unexpected and unique electromagnetic properties of chiral structures with nanoscale and microscale dimensions, including giant circular dichroism and collective circularly polarized scattering that their constituent units did not possess. To address the wide variety of chiral geometries observed in continuous materials, singular particles, and their complex systems, multiple analytic techniques are needed. Simultaneously, their spectroscopic properties create a pathway to multiple applications. For example, mirror-asymmetric vibrations at chiral centers formed by sp 3 carbon atoms lead to optical activity for the infrared (IR) wavelength regions. At the same time, understanding the optical activity in, for example, the IR region enables biomedical applications because multiple modalities of biomedical imaging and vibrational optical activity (VOA) of biomolecules are known for IR range. In turn, VOA can be realized in both absorption and emission modalities due to large magnetic transition moments, as vibrational circular dichroism (VCD) or Raman optical activity (ROA) spectroscopy. In addition to the VOA, in the range of longer wavelengths, lattice vibrational mode or phononic behavior occurs in chiral crystals and nanoassemblies, which can be readily detected by terahertz circular dichroism (TCD) spectroscopy. Meanwhile, chiral self-assembly can induce circularly polarized light emission (CPLE) regardless of the existence of chirality in coassembled fluorophores. The CPLE from self-assembled chiral materials is particularly interesting because the CPLE can originate from both circularly polarized luminescence and circularly polarized scattering (CPS). Furthermore, because self-assembled nanostructures often exhibit stronger optical activity than their building blocks owing to dimension and resonance effects, the optical activity of single assembled nanostructures can be investigated by using microscopic technology combined with chiral optics. Here, we describe the state of the art for spectroscopic methods for the comprehensive analysis of chiral nanomaterials at various photon wavelengths, addressed with special attention given to new tools emerging both for materials with self-organized hierarchical chirality and single-particle spectroscopy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Morphological Transitions of a Photoswitchable Aramid Amphiphile Nanostructure

Self-assembly of small amphiphilic molecules in water can lead to nanostructures of varying geometries with pristine internal molecular organization. Here we introduce a photoswitchable aramid amphiphile (AA), designed to exhibit extensive hydrogen bonding and robust mechanical properties upon self-assembly, while containing a vinylnitrile group for photoinduced cis-trans isomerization. We demonstrate spontaneous self-assembly of the vinylnitrile-containing AA in water to form nanoribbons. Upon UV irradiation, trans-to-cis isomerizations occur concomitantly with a morphological transition from nanoribbons to nanotubes. The nanotube structure persists in water for over six months, stabilized by strong and collective intermolecular interactions. We demonstrate that the nanoribbon-to-nanotube transition is reversible upon heating and that switching between states can be achieved repeatedly. Finally, we use electron microscopy to capture the transition and propose mechanisms for nanoribbon-to-nanotube rearrangement and vice versa. This stability and switchability of photoresponsive AA nanostructures make them viable for a range of future applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Design and Control of Three-Dimensional Topological Magnetic Fields Using Interwoven Helical Nanostructures

Three-dimensional (3D) magnetic nanostructures are an emerging platform capable of creating complex topological magnetic fields. The control of localized nanoscale magnetic fields is seen to be of importance for diverse areas from bioapplications such as drug delivery, to particle trapping and controlling Majorana Fermions for quantum computing. Three-dimensional geometric confinement and proximity can create tailor-made spin textures not possible in two dimensions. The control of magnetization afforded here can allow the formation of unique stray field textures. Here, we report the creation of reconfigurable 3D topological magnetic field textures induced by an interwoven 3D nanostructure and applied field protocol. These field textures emerge due to distinct DWs formed in this structure and lead to the creation of an antivortex field, a hexapole cusp and a 3D skyrmion field tube of mixed chirality. In conclusion, our results therefore show a key step toward the design and control of topological magnetic fields on the nanoscale.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Strategy for Nonenzymatic Harvesting of Cells via Decoupling of Adhesive and Disjoining Domains of Nanostructured Stimulus-Responsive Polymer Films

The nanostructured polymer film introduces a novel mechanism of nonenzymatic cell harvesting by decoupling solid cell-adhesive and soft stimulus-responsive cell-disjoining areas on the surface. The key characteristics of this architecture are the decoupling of adhesion from detachment and the impermeability to the integrin protein complex of the adhesive domains. This surface design eliminates inherent limitations of thermoresponsive coatings, namely, the necessity for the precise thickness of the coating, grafting or cross-linking density, and material of the basal substrate. The concept is demonstrated with nanostructured thermoresponsive films made of cell-adhesive epoxy photoresist domains and cell-disjoining poly(N-isopropylacrylamide) brush domains.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Sequential Infiltration Synthesis of Bilayer Porous Alumina Nanostructures for Broad-Angle, Broadband Antireflective Coatings

Antireflective coatings (ARCs) are thin films engineered to reduce light reflections. Delivering broadband, wide-angle performance is essential for photovoltaics, imaging, and sensing, yet truly omnidirectional antireflection remains difficult due to angle-dependent optical paths and a narrow palette of suitable refractive indices. Here, in this study, we systematically investigate an emerging class of multilayer inorganic ARCs based on conformally coated nanoporous alumina templated by intrinsically microporous polymers (PIMs) and block copolymers (BCPs). We establish a design framework that maps thickness reflectance relationships to identify thickness pairs minimizing reflection across wavelength and incidence angle. We show that deliberately separating the local reflectance minima of the top and bottom layers in bilayer nanostructures broadens the antireflective bandwidth and angular range. We show that 235-nm single-side bilayer porous alumina nanostructures achieves under 2 % reflectance from 380–750 nm for incidence angles up to 45° with less than 0.6% reflectance for incidence angles under 20°. The approach is readily extensible to additional layers or materials with refractive indices tuned via templated nanoporosity and composition, enabling practical, etch-free ARC fabrication without HF or fluorinated precursors and advancing straightforward design of broadband, wide-angle (quasi-omnidirectional) ARCs for next-generation optical systems.

antireflective coatings↗
DOE OSTI2021

Progress, Challenges, and Opportunities in the Synthesis, Characterization, and Application of Metal-Boride-Derived Two-Dimensional Nanostructures

Two-dimensional (2D) metal-boride-derived nanostructures have been a focus of intense research for the past decade, with an emphasis on new synthetic approaches, as well as on the exploration of possible applications in next-generation advanced materials and devices. Their unusual mechanical, electronic, optical, and chemical properties, arising from low dimensionality, present a new paradigm to the science of metal borides that has traditionally focused on their bulk properties. This Perspective discusses the current state of research on metal-boride-derived 2D nanostructures, highlights challenges that must be overcome, and identifies future opportunities to fully utilize their potential.

metals↗
DOE OSTI2022

Nontrivial nanostructure, stress relaxation mechanisms, and crystallography for pressure-induced Si-I → Si-II phase transformation

Crystallographic theory based on energy minimization suggests austenite-twinned martensite interfaces with specific orientation, which are confirmed experimentally for various materials. Pressure-induced phase transformation (PT) from semiconducting Si-I to metallic Si-II, due to very large and anisotropic transformation strain, may challenge this theory. Here, unexpected nanostructure evolution during Si-I → Si-II PT is revealed by combining molecular dynamics (MD), crystallographic theory, generalized for strained crystals, and in situ real-time Laue X-ray diffraction (XRD). Twinned Si-II, consisting of two martensitic variants, and unexpected nanobands, consisting of alternating strongly deformed and rotated residual Si-I and third variant of Si-II, form {111} interface with Si-I and produce almost self-accommodated nanostructure despite the large transformation volumetric strain of -0.237. The interfacial bands arrest the {111} interfaces, leading to repeating nucleation-growth-arrest process and to growth by propagating {110} interface, which (as well as {111} interface) do not appear in traditional crystallographic theory.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Pulsed laser heating of diesel engine and turbojet combustor soot: Changes in nanostructure and implications

Here, carbonaceous particulate produced by a diesel engine and turbojet engine combustor are analyzed by transmission electron microscopy (TEM) for differences in nanostructure before and after pulsed laser annealing. Soot is examined between low/high diesel engine torque and low/high turbojet engine thrust. Small differences in nascent nanostructure are magnified by the action of high-temperature annealing induced by pulsed laser heating. Lamellae length distributions show occurrence of graphitization while tortuosity analyses reveal lamellae straightening. Differences in internal particle structure (hollow shells versus internal graphitic ribbons) are interpreted as due to higher internal sp3 and O-atom content under the higher power conditions with hypothesized greater turbulence and resulting partial premixing. TEM in concert with fringe analyses reveal that a similar degree of annealing occurs in the primary particles in soot from both diesel engine and turbojet engine combustors—despite the aggregate and primary size differences between these sources. Implications of these results for source identification of the combustion particulate and for laser-induced incandescence (LII) measurements of concentration are discussed with inter-instrument comparison of soot mass from both diesel and turbojet soot sources.

42 ENGINEERING↗
DOE OSTI2023

In-situ study of rules of nanostructure evolution, severe plastic deformations, and friction under high pressure

Severe plastic deformations under high pressure are used to produce nanostructured materials but were studied ex-situ. Rough diamond anvils are introduced to reach maximum friction equal to yield strength in shear and the first in-situ study of the evolution of the pressure-dependent yield strength and radial distribution of nanostructural parameters are performed for severely pre-deformed Zr. ω-Zr behaves like perfectly plastic, isotropic, and strain-path-independent and reaches steady values of the crystallite size and dislocation density, which are pressure-, strain- and strain-path-independent. However, steady states for a-Zr obtained with smooth and rough anvils are different, causing major challenge in plasticity theory. In-situ study of severe plastic deformation of α-Zr with rough diamond anvils revealed that pressure-dependent yield strength, crystallite size, and dislocation density are getting steady and plastic strain- and strain-path-independent.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Superior plastic flow stability of self-patterned carbide – amorphous ceramic nanostructures

Amorphous ceramics and carbides exhibit superb strength but poor plasticity. Here, we synthesized TiC-SiOC nanostructures with TiC-nanocarbides embedded in amorphous ceramic SiOC by co-sputtering followed by high-temperature annealing and/or irradiation. TiC-SiOC nanostructures exhibit high strength and good plastic flow stability even after heavy irradiation, 7 GPa at room temperature and 3.6 GPa at 700 ℃ with a uniform strain of about 10%∼18%. The uniform deformation is accommodated by the shearing of amorphous ceramic and the rotation of nanocarbides. Nanocarbides inhibit the propagation of shear banding in amorphous SiOC, and amorphous-crystal interfaces act as sinks to manage irradiation-induced defects.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Two-Photon Spontaneous Emission in Atomically Thin Plasmonic Nanostructures

The ability to harness light-matter interactions at the few-photon level plays a pivotal role in quantum technologies. Single photons—the most elementary states of light—can be generated on demand in atomic and solid state emitters. Two-photon states are also key quantum assets, but achieving them in individual emitters is challenging because their generation rate is much slower than competing one-photon processes. We demonstrate that atomically thin plasmonic nanostructures can harness two-photon spontaneous emission, resulting in giant far field two-photon production, a wealth of resonant modes enabling tailored photonic and plasmonic entangled states, and plasmon-assisted single-photon creation orders of magnitude more efficient than standard one-photon emission. We unravel the two-photon spontaneous emission channels and show that their spectral line shapes emerge from an intricate interplay between Fano and Lorentzian resonances. Enhanced two-photon spontaneous emission in two-dimensional nanostructures paves the way to an alternative efficient source of light-matter entanglement for on-chip quantum information processing and free-space quantum communications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Sustainable and Green Production of Nanostructured Cellulose by a 2-Step Mechano-Enzymatic Process

Nanostructured cellulose (NC) represents an emerging sustainable biomaterial for diverse biotechnological applications; however, its production requires hazardous chemicals that render the process ecologically unfriendly. Using commercial plant-derived cellulose, an innovative strategy for NC production based on the combination of mechanical and enzymatic approaches was proposed as a sustainable alternative to conventional chemical procedures. After ball milling, the average length of the fibers was reduced by one order of magnitude (down to 10–20 μm) and the crystallinity index decreased from 0.54 to 0.07–0.18. Moreover, a 60 min ball milling pre-treatment followed by 3 h Cellic Ctec2 enzymatic hydrolysis led to NC production (15% yield). Analysis of the structural features of NC obtained by the mechano-enzymatic process revealed that the diameters of the obtained cellulose fibrils and particles were in the range of 200–500 nm and approximately 50 nm, respectively. Interestingly, the film-forming property on polyethylene (coating ≅ 2 μm thickness) was successfully demonstrated and a significant reduction (18%) of the oxygen transmission rate was obtained. Altogether, these findings demonstrated that nanostructured cellulose could be successfully produced using a novel, cheap, and rapid 2-step physico-enzymatic process that provides a potential green and sustainable route that could be exploitable in future biorefineries.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Synthesis of 2H/ fcc -Heterophase AuCu Nanostructures for Highly Efficient Electrochemical CO 2 Reduction at Industrial Current Densities

Structural engineering of nanomaterials offers a promising way for developing high-performance catalysts toward catalysis. However, the delicate modulation of thermodynamically unfavorable nanostructures with unconventional phases still remains a challenge. Here, in this study, the synthesis of hierarchical AuCu nanostructures is reported with hexagonal close-packed (2H-type)/face-centered cubic (fcc) heterophase, high-index facets, planar defects (e.g., stacking faults, twin boundaries, and grain boundaries), and tunable Cu content. The obtained 2H/fcc Au 99 Cu 1 hierarchical nanosheets exhibit excellent performance for the electrocatalytic CO 2 reduction to produce CO, outperforming the 2H/fcc Au 91 Cu 9 and fcc Au 99 Cu 1 . The experimental results, especially those obtained by in-situ differential electrochemical mass spectroscopy and attenuated total reflection Fourier-transform infrared spectroscopy, suggest that the enhanced catalytic performance of 2H/fcc Au 99 Cu 1 arises from the unconventional 2H/fcc heterophase, high-index facets, planar defects, and appropriate alloying of Cu. Impressively, the 2H/fcc Au 99 Cu 1 shows CO Faradaic efficiencies of 96.6% and 92.6% at industrial current densities of 300 and 500 mA cm -2 , respectively, as well as good durability, placing it among the best CO 2 reduction electrocatalysts for CO production. The atomically structural regulation based on phase engineering of nanomaterials (PEN) provides an avenue for the rational design and preparation of high-performance electrocatalysts for various catalytic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Dual‐Scale Nanostructures via Evaporative Assembly

Abstract Dual‐scale hierarchical structures with regular microscale patterns and varying degree of nanoscale crystalline order are synthesized on physically and chemically homogeneous substrates by evaporative self‐assembly with a suspension of DNA‐functionalized nanoparticles (NPs) with a charged core shell. For a certain NP concentration range, periodic concentric rings in a stripe‐like micropattern are produced over macroscale surface areas by an NP monolayer with hexagonal lattice structure at the nanoscale. The stripe width, spacing, and nanoparticle ordering can be controlled by varying the NP concentration. The results indicate that the interplay between “stick‐slip” motion of the droplet contact line and coulombic and steric NP interactions control the formation of the observed structures. A simple analytical model is proposed to account for the experimental observations and guide the future design of different nanostructure morphologies. This work demonstrates a simple cost‐effective mask‐free method for fabricating large‐area nanostructured 2D materials and metasurfaces for applications ranging from energy conversion/storage to optoelectronics and nanophotonics.

Srivastava, Sunita↗
DOE OSTI2023

Oxidation Driven Thin‐Film Solid‐State Metal Dealloying Forming Bicontinuous Nanostructures

Abstract Solid‐state metal dealloying (SSMD) is a promising method for fabricating nanoscale metallic composites and nanoporous metals across a range of materials. Thin‐film SSMD is particularly attractive due to its ability to create fine features via solid‐state interfacial reactions within a thin‐film geometry, which can be integrated into devices for various applications. This work examines a new dealloying couple, namely the Nb–Al alloy with the dealloying agent Sc, as previously predicted in the machine‐learning (ML) models. Prior ML predictions aimed to guide the design of nanoarchitectured materials through dealloying, relying on intuition‐driven discovery within a large parameter space. However, this work reveals that at the nanoscale, the involvement of oxygen in thin film processing may instead drive the dealloying process, resulting in the formation of bicontinuous nanostructures similar to those formed by metal‐agent dealloying. The phase evolution, as well as chemical and morphological changes, are closely analyzed using a combination of X‐ray absorption spectroscopy, diffraction, and scanning transmission electron microscopy to understand the mechanisms behind nanostructure formation. The findings suggest a potential pathway for utilizing oxygen to drive the formation of bicontinuous metal–metal oxide nanocomposites, paving the way for further development of functional nanoporous materials in diverse fields.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Spatiotemporal Studies of Soluble Inorganic Nanostructures with X‐rays and Neutrons

Abstract This Review addresses the use of X‐ray and neutron scattering as well as X‐ray absorption to describe how inorganic nanostructured materials assemble, evolve, and function in solution. We first provide an overview of techniques and instrumentation (both large user facilities and benchtop). We review recent studies of soluble inorganic nanostructure assembly, covering the disciplines of materials synthesis, processes in nature, nuclear materials, and the widely applicable fundamental processes of hydrophobic interactions and ion pairing. Reviewed studies cover size regimes and length scales ranging from sub‐Ångström (coordination chemistry and ion pairing) to several nanometers (molecular clusters, i.e. polyoxometalates, polyoxocations, and metal‐organic polyhedra), to the mesoscale (supramolecular assembly processes). Reviewed studies predominantly exploit 1) SAXS/WAXS/SANS (small‐ and wide‐angle X‐ray or neutron scattering), 2) PDF (pair‐distribution function analysis of X‐ray total scattering), and 3) XANES and EXAFS (X‐ray absorption near‐edge structure and extended X‐ray absorption fine structure, respectively). While the scattering techniques provide structural information, X‐ray absorption yields the oxidation state in addition to the local coordination. Our goal for this Review is to provide information and inspiration for the inorganic/materials science communities that may benefit from elucidating the role of solution speciation in natural and synthetic processes.

Yin, Jia‐Fu↗