Search NASA⌕ Search

SEARCH · Search NASA

Results for “PBF”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

The Influence of Residual Stress on Fatigue Crack Growth Rates in Stainless Steel Processed by Different Additive Manufacturing Methods

The properties and microstructure of Type 304L stainless steel produced by two additive manufacturing (AM) methods—directed energy deposition (DED) and powder bed fusion (PBF)—are evaluated and compared. Localized heating and steep temperature gradients of AM processes lead to significant residual stress and distinctive microstructures, which may be process-specific and influence mechanical behavior. Test data show that materials produced by DED and PDF have small differences in tensile strengths but clear differences in residual stress and microstructural features. Measured fatigue crack growth rates (FCGRs) for cracks propagating parallel to and perpendicular to the build directions differ between the two AM materials. To separate the influences of residual stress and microstructure, K-control test procedures with decreasing and constant stress intensity factor ranges are used to measure FCGRs in the near-threshold regime (crack growth rates ≤ 1 × 10 −8 m/cycle). Residual stress is quantified by the residual stress intensity factor, K res , measured by the online crack compliance method. Correcting the FCGR data for differences in K res brings results for specimens of the two AM materials into agreement with each other and with results for wrought specimens, when the latter are corrected for crack closure. Differences in microstructure and tensile strength have an insignificant influence on FCGRs in these tests.

additive manufacturing↗
DOE OSTI2025

Suppressing Ordering in Equiatomic Fe-Co via Laser Powder Bed Fusion

Neutron and electron diffraction was employed to evaluate the effectiveness of thermal management strategies in suppressing the formation of the equilibrium-ordered B2 (CsCl) phase in equiatomic binary Fe-Co specimens fabricated by laser powder bed fusion additive manufacturing. Specimens with a tensile dogbone geometry were fabricated using various combinations of process parameters (laser power and raster speed) and thermal management strategies (no support struts, struts only in the top gauge section, and struts throughout the gauge section). Diffraction results demonstrate that the rapid solidification during PBF-L effectively minimized B2 formation, with laser power and effective scan velocity having no significant impact on the degree of ordering. Furthermore, the inclusion of support struts in the top grip region had no perceivable impact on ordering, whereas specimens with support struts in the gauge region exhibited no detectable ordering. Results are discussed in the context of thermal finite element analysis predictions.

Laser Material Processing↗
DOE OSTI2024

Location-Specific Microstructure Characterization Within AM Bench 2022 Nickel Alloy 718 3D Builds

Abstract The Additive Manufacturing Benchmark Test Series (AM Bench) is a broad effort to produce rigorous measurement datasets for validating AM computer simulations across the range of processing, structure, and properties, for many additive manufacturing (AM) build methods and material classes. Here, the microstructures of nickel alloy 718 AM Bench 2022 test artifacts produced using laser-based powder bed fusion (PBF-LB), in both as-built and fully heat-treated conditions, are examined. Cross sections are primarily characterized using large area scanning electron microscopy (SEM) electron backscatter diffraction (EBSD) and example analyses of the crystallographic textures are described. These data are part of a large set of in situ and ex situ measurements from both three-dimensional builds and laser tracks on bare plates. All the measurement data are available online with download links at www.nist.gov/ambench .

Levine, L. E. (ORCID:0000000334484229)↗
DOE OSTI2024

Operando visualization of porous metal additive manufacturing with foaming agents through high-speed x-ray imaging

Porous metals find extensive applications in soundproofing, filtration, catalysis, and energy-absorbing structures, thanks to their unique internal pore structure and high specific strength. In recent years, there has been an increasing interest in fabricating porous metals using additive manufacturing (AM), leveraging its unique advantages, including improved design freedom, spatial material control, and cost-effective small-batch production. In this study, we conducted pioneering operando visualization of AM porous metal using a laser powder bed fusion (L-PBF) setup combined with a high-speed synchrotron x-ray imaging system. Single track printing experiments using Ti6Al4V (Ti64) combined with titanium hydride (TiH 2 ) and sodium carbonate (Na 2 CO 3 ) as foaming agents, with varying mixing ratios were performed under different processing conditions. Here. the results elucidate the dynamic development of porosity formation. The average pore size is significantly influenced by the particle size of foaming agents when pore coalescence is absent. For all foaming agent content tested in the current study, the number of pores is found to be more sensitive to changes in laser power than in laser scanning speed. Increasing linear energy density (increasing laser power or reducing laser scanning speed) promotes the foaming agent activation thereby porosity formation. However, high linear energy density skews pore distribution towards the surface despite forming deeper melt pools. In addition, the impact of additional factors including foaming agent's laser absorptivity and decomposition kinetics with respect to AM time scales should be carefully considered to avoid ineffective activation of foaming agents during the AM of porous metals.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Effect of Zr and Sc additions on coarsening- and creep resistance of AlSi10Mg fabricated by laser powder bed fusion

Microstructure and creep properties are studied in a eutectic AlSi10Mg alloy modified with Zr and Sc additions (Al-9.8Si-0.32Mg-0.70Zr-0.23Sc, wt%) manufactured through laser powder-bed fusion (L-PBF). Three types of Zr/Sc-bearing powders - elemental, master-alloy, and pre-alloyed - are employed in the fabrication process, with the pre-alloyed powders providing the highest incorporation of Zr and Sc in the Al matrix. Here, the as-printed alloy exhibits a fine cellular Al-Si eutectic structure which fragments and coarsens into micron-sized Si particles during aging at 300 ºC, leading to a steady drop in alloy microhardness between 0.1 and 1000 h. Coarsening of the eutectic Si phase during aging is not measurably affected by Zr and Sc in solid solution, which precipitate during aging and increases strength, compensating weakening from Si coarsening between 1 and 200 h at 300 ºC. Atom-probe analysis in the peak-aged condition (96 h/300 °C) confirms the presence of Al 3 (Sc,Zr) secondary nano-precipitates with an average radius of 1.0 nm and some Si solubility. Micron-sized grains are present throughout the alloy, with ultra-fine-grained regions at the melt pool boundaries, neither of which coarsen during long-term aging at 300 ºC. Under creep conditions at 300 °C, the Zr/Sc-bearing alloy with Al 3 (Sc,Zr) nano-precipitates exhibits power-law behavior, with a high apparent stress exponent (n a = 9) and a high threshold stress (σ th = 43 MPa), exhibiting nearly double the strength of a Zr/Sc-free AlSi10Mg control alloy (σ th = 22 MPa).

36 MATERIALS SCIENCE↗
DOE OSTI2025

Modeling low cycle fatigue (LCF) of additively manufactured Hastelloy X using An accelerated crystal plasticity fatigue damage model

This paper presents a microstructure-based model for low cycle fatigue (LCF) behavior and life of Nickel-based alloy Hastelloy X manufactured using laser-powder bed fusion (L-PBF) additive manufacturing (AM). AM Hastelloy X, a solution-strengthened alloy, is tested at elevated temperature under fully reversed LCF conditions at different strain levels. A generalized plane strain finite element model is generated from electron backscatter diffraction (EBSD) characterization. The constitutive behavior of the material under fatigue is modeled using crystal plasticity and calibrated with both monotonic tensile and cyclic stress–strain data. The fatigue micro-crack initiation and propagation in the microstructure is modeled using a modified Chaboche fatigue damage model. An embedded boundary condition with a homogenous medium is used to apply the cyclic deformation and prevent numerically introduced over-constraints during fatigue simulation. A ‘cycle-jump’ method is used to accelerate the fatigue simulation and reduce the computational cost. The simulation results are compared to LCF experiments, showing satisfactory matches in cyclic stress behavior and number of cycles to macro-crack initiation for all applied strain ranges. In addition, the model illustrates the potential for quantifying microscale fatigue life impacting factors such as microstructure and surface roughness, which is needed to accurately quantify the reliability of AM components in service.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High-pressure high-temperature melting and recrystallization of nanolamellar high-entropy alloys

Additively manufactured (AM) High Entropy Alloys (HEAs) are notable for their exceptional high-yield strength and large tensile ductility. The nanolamellar Eutectic HEA (EHEA) AlCoCrFeNi 2.1 was fabricated by laser powder bed fusion (L-PBF) in the as-printed form (EHEA1) and subsequently annealed at 1000oC (EHEA2) and 600oC (EHEA3) to achieve a broad range of mechanical properties. EHEA2 and EHEA3 samples were studied using Scanning transmission electron microscopy (STEM), energy dispersive X-ray diffraction (EDXRD) at high-pressures and high temperatures, nanoindentation hardness and modulus measurements. According to EDXRD EHEA2 and EHEA3 are composed of B2 and L1 2 phases. High-pressure high-temperature EDXRD studies show melting for EHEA2 at 1698 ± 25 K at a pressure of 6.5 GPa and melting for EHEA3 at 1598 ± 25 K at a pressure of 5.8 GPa. Post-melt and recrystallized samples were recovered at ambient conditions, and XRD analysis showed retention of B2 and L1 2 phases, although a new σ phase appeared for both EHEA2 and EHEA3 samples due to high-pressure and high-temperature melting and recrystallization experiment. SEM analysis also demonstrated the preservation of the nanolamellar morphology. Nanoindentation studies revealed that recrystallized EHEAs retain their original mechanical property hierarchy, with EHEA3 being 47% harder than EHEA2, largely related to higher content of B2-phase and retention of nanolamellar morphology. We also present Pressure-Volume-Temperature (P-V-T) data for 3-D printed and annealed eutectic high entropy alloys and extract mechanical and thermal properties data.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A high-throughput approach for statistical process optimization in Laser Powder Bed Fusion

Process variability is inherent in metal additive manufacturing (AM). However, it is often overlooked in process optimization frameworks, constraining the understanding of process uncertainties and their influence on parameter selection. To address this, we present an integrated framework that combines high-throughput single-track experiments, GAN-based melt pool geometry extraction, robust statistical and machine learning modeling, and uncertainty-quantified process mapping. Process variability is characterized through single-track melt pool behaviors, and its influence on defect formation is systematically quantified to enable statistically guided process parameter optimization. This approach is demonstrated on Laser Powder Bed Fusion (L-PBF) of stainless steel 316L, effectively capturing the interplay between process parameters, melt pool variability, and defect probability. By integrating uncertainty quantification into process optimization, this study provides a structured methodology for addressing variability challenges in AM quality control, ultimately contributing to enhanced manufacturing reliability.

Laser Powder Bed Fusion↗
DOE OSTI2026

Insights into elevated temperature tensile deformation mechanisms and kink banding in additively manufactured tungsten

Additive manufacturing (AM) potentially enables fabrication and repair of plasma facing components (PFCs) of tungsten. However, deformation mechanisms in AM-fabricated tungsten under service-relevant thermomechanical conditions remain unknown majorly due to challenges in achieving crack-free W. This study reveals the deformation mechanisms operative under tension at 800 °C and 1200 °C in the electron beam melting powder bed fusion (EBM-PBF) fabricated W. Textured columnar grains with mixed <001 >/<111 >|| build-direction were observed. Strong anisotropy in tensile properties persisted across test temperatures, and all specimens exhibited extensive deformation-induced banding phenomena. Grain boundary character analysis of the deformed specimens indicated that these deformation bands were kink bands with tilt grain boundaries prominently present at the band-matrix interface. Interestingly, the material within the kink bands rotated toward higher resolved shear stress, providing insights into the origins of kink band formation in body-centered cubic refractory metals. Intragranular misorientation axis analysis revealed that plasticity was dominated by {110} <111 > slip at 800 °C, whereas additional (213)[11⁢̄1] and (112)[11⁢̄1] slip systems activated at 1200 °C. A dense low-angle boundary networks observed near fractured surface indicated the onset of dynamic recrystallization. Results reveal plasticity governing mechanisms in AM-fabricated W under power plant-relevant conditions, and provide insights into kink band attributes in refractory metals.

Mayes, Riley [ORNL] (ORCID:000900089307010X)↗
DOE OSTI2024

Clarifying the formation of equiaxed grains and microstructural refinement in the additive manufacturing of Ti-Cu

Controlling microstructural evolution in metallic additive manufacturing (AM) is difficult, especially in producing refined as-built grains instead of coarse, directional grains. Traditional solutions involve adding inoculants to AM feedstocks, but titanium (Ti) alloys cannot employ this approach without producing detrimental secondary phases. Ti-Cu (Ti-copper) alloys offer a solution through constitutional supercooling and/or solid state thermal cycling under AM conditions. This work analyzes a compositionally graded directed energy deposition (DED) Ti-Cu build, single-melt laser tracks, and dilatometric heat treatments to evaluate if, when, and by what mechanism(s) microstructural refinement occurs. Refinement by inoculation of unmelted powder particles was also considered. Constitutional supercooling produced no net microstructural refinement as any equiaxed dendrites which form are remelted with new deposition. This finding agreed with solidification modeling of powder bed fusion-laser beam (PBF-LB) and DED builds. Solid state thermal cycling refined microstructures only during ex-situ dilatometric heat treatments, suggesting build parameter optimization is needed to achieve refinement in-situ. Accidental heterogeneous nucleation on unmelted Ti powder, originating from the different thermophysical properties of Ti and Cu, provided the most significant microstructural refinement. This work systematically assesses the microstructural refinement mechanisms of Ti-Cu in AM builds and offers insights into microstructural control in eutectoid alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Ultrasonic characterization of material heterogeneities in stainless steel components produced by laser powder bed fusion

We introduce pulse-echo ultrasound as a method for characterizing the impact of powder bed fusion parameters on the properties of additively manufactured stainless-steel components, their material anisotropy, and location-dependent heterogeneity. Our results indicate that accurate characterization requires careful selection of ultrasonic propagation paths, which must consider the direction of additive layering, variations in processing parameters, and the component's geometry. We employed two distinct methods to estimate material properties from ultrasonic data: One assumes isotropy, while the other accounts for anisotropic interactions during the propagation of elastic waves. When applied to samples fabricated with laser energy densities ranging from 24 to 42 J/mm³ , these methods revealed transverse isotropy and weak anisotropy (quantified by small Thomsen parameters, ε = 0.0651 and γ = 0.0092) and less than a ∼6 % change in acoustic impedance. The assumption of isotropy, in this case, leads to small errors (less than 4 % or 1 % for Young's modulus in the build or transverse directions) when estimating orthotropic material properties using ultrasonic data measured along just two orthogonal directions, one of which must align with the build direction. By comparing ultrasonic measurements — which aggregate the spatial variability in material properties along the length of elastic wave propagation into a single value — with localized measurements obtained from surface nanoindentation, we uncovered and spatially profiled significant differences between the surface and interior properties. Specifically, the surface Young's modulus decreased from approximately 210 GPa to 180 GPa within a depth of about 3 mm. We attribute this surface-localized heterogeneity in PBF-fabricated components to distinct thermal histories experienced by the surface and interior regions. Collectively, the results of this study establish a framework for the ultrasonic characterization of material heterogeneity and anisotropy in material properties and demonstrate its application in additively manufactured metal components.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Development of a Method for Shape Optimization for a Gas Turbine Fuel Injector Design Using Metal-Additive Manufacturing

Adjoint shape optimization has enabled physics-based optimal designs for aerodynamic surfaces. Additive manufacturing (AM) makes it possible to manufacture complex shapes. However, there has been a gap between optimal and manufacturable surfaces due to the inherent limitations of commercial computational fluid dynamics (CFD) codes to implement geometric constraints during adjoint computation. In such cases, the design sensitivities are exported and used to perform constrained shape modifications using parametric information stored in computer aided design (CAD) files to satisfy manufacturability constraints. However, modifying the design using adjoint methods in CFD solvers and performing constrained shape modification in CAD can lead to inconsistencies due to different shape parameterization schemes. This paper describes a method to enable the simultaneous optimization of the fluid domain and impose AM manufacturability constraints, resolving one of the key issues of geometry definition for isogeometric analysis. Similar to a grid convergence study, the proposed method verifies the consistencies between shape parameterization techniques present within commercial CAD and CFD software during mesh movement as a part of the adjoint shape optimization routine. By identifying the appropriate parameters essential to a shape optimization study, the error metric between the different parameterization techniques converges to demonstrate sufficient consistencies for justifiable exchange of data between CAD and CFD. For the identified shape optimization parameters, the error metric to measure the deviation between the two parameterization schemes lies within the AM laser-powder bed fusion (L-PBF) process tolerance. Additionally, comparison for subsequent objective function calculations between iterations of the optimization loop showed acceptable differences within 1% variation between the modified geometries obtained using the two parameterization schemes. This method provides justification for the use of multiphysics guided adjoint design sensitivities computed in CFD software to perform shape modifications in CAD to incorporate AM manufacturability constraints during the shape optimization loop such that optimal designs are also additively manufacturable.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Selective Deposition and Fusion of AISI 316L: An Additive Manufacturing Process for Space Environments via Direct Ink Writing and Laser Processing

Unlocking the potential of additive manufacturing (AM) for space exploration hinges on overcoming key challenges, notably the ability to manufacture or repair parts on-site during exploration missions with consideration of quality, feedstock utilization, and challenges involved in microgravity environments. While there are multiple efforts to investigate the use of existing metal AM processes such as powder bed fusion (PBF), directed energy deposition (DED), and filament-based material extrusion, each process comes with a different set of challenges in space environments. Here, in this work, we introduce a new AM method that integrates the benefits of direct ink writing (DIW) to selectively deposit metallic pastes with laser-based processing to locally debind and subsequently melt and fuse metal powder, layer by layer, enabling the manufacturing of AISI 316L samples with densities exceeding 99.0%. The impact of process parameters on single-track dimensions, surface morphology, and porosity was characterized. The efficacy of laser debinding was assessed via secondary-ion mass spectrometry, permitting the carbon content to be estimated at 0.0152%, which is safely below the acceptable limit (0.03 wt%) for AISI 316L.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermomechanical Behavior of Advanced Manufactured Parts, Subcomponents, and Their Weldments for Gen3 CSP

Generation 3 (Gen3) concentrating solar power (CSP) plants may require the use of molten chloride salt storage systems, solar receivers, and supercritical-CO 2 primary heat exchangers (PHX). The temperatures that would be expected in these parts and subcomponents could approach 760°C for hot side and 500°C for cold side at peak operating conditions. With the design limitations, highly corrosion- and creep-resistant alloys are needed for maximizing component lives. This report presents the results for the project "Thermomechanical Behavior of Advanced Manufactured Parts, Subcomponents, and their Weldments for Gen3 CSP", award number DE-EE00036334. In this project, creep enhanced ferritic alloy Grade 91, austenitic stainless-steel (SS) 304H, Ni claddings Ni201 and C22, and nickel-based superalloys Inconel 740H and Haynes 282 and 230 were evaluated for potential applications in Gen3 CSP systems. Advanced manufacturing of these parts, subcomponents and their welds, was investigated and a full technoeconomic analysis was made in comparison to conventional manufacturing techniques. The manufacturing techniques explored are explosion clad welding and combustion synthesis/combustion reaction for transfer pipes, additive manufacturing (AM) including laser-powder bed fusion (L-PBF) and electron beam AM (EBAM) with wire feedstock for PHX and solar receivers, and conventional fusion welding for similar and dissimilar joining of these various parts and subcomponents.

14 SOLAR ENERGY↗
DOE OSTI2024

Microstructure Optimization and Novel Processing Development of ODS Steels for Fusion Environments (Final ARPA-E Report)

This project aimed to develop scalable, cost-effective fabrication of high-performance, oxide- dispersion-strengthened (ODS) steel using advanced manufacturing methods (AMMs) for fusion blanket-breeding applications. Gas atomization reaction synthesis (GARS) enables the synthesis of precursor ODS steel powders without prolonged mechanical alloying. This process creates a chromium (Cr)-enriched surface oxide with yttrium/titanium (Y/Ti)-enriched intermetallics in powder interiors. GARS powders were consolidated to >99% of the theoretical density using a first-of-a-kind shear assisted processing and extrusion (ShAPE) and laser-based powder bed fusion (L-PBF) AM processes. These processes led to ODS steels containing a high-density of nano-oxide dispersoids that enhance high-temperature mechanical properties. Such scalable, cost-effective fabrication of ODS steels can enable efficient power conversion cycles (=40%) at operating temperatures beyond 900 K in future fusion power plants.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Computational Design to Advance AM Fabrication of High Gamma Prime Alloys for Hot Gas Path Components in Gas Turbine Engines: A Pathway to Enhanced Gas Turbine Efficiency and Energy Saving (Final CRADA Report)

Raising turbine inlet temperature is a key lever for improving industrial gas-turbine efficiency and power output, but it increases thermo-mechanical demands on hot-gas-path components. Additive manufacturing (AM), particularly laser powder bed fusion (L-PBF), enables complex internal cooling features in critical components such as turbine tip shoes that are difficult to produce by conventional casting. However, qualification of new high-temperature AM alloys and aggressive geometries is often limited by trial-and-error iteration of build parameters and post-build heat treatments, with cracking during stress relieving or hot isostatic pressing (HIP) being a recurring failure mode.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

Truchas Overview

Truchas and Truchas-PBF are two sister codes for part-scale multi-physics modeling of manufacturing processes. Both programs are open source and made publicly available. They’re designed for efficient use of HPC resources and can be programmatically driven from Python packages. This enables automatic execution and analysis of ensembles of simulations, in some cases allowing 1000s of simulations to be evaluated in a day on HPC. Beyond just giving engineers a window into the concealed internal state of a system, the goal of Truchas is to provide a framework for developing novel manufacturing processes by understanding how the entire space of engineering inputs affects thermal state. It often is used to explore combinations of capabilities uncommon in commercial software, or to scale up analyses beyond the capabilities of commercial software.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS2018

Three-Dimensional Printing GRCop-42

GRCop-42 (Cu-4 at.% Cr-2 at.% Nb) is a copper (Cu)-chromium (Cr)-niobium (Nb) alloy that NASA developed for use in rocket propulsion components that required high thermal conductivity, excellent creep resistance, low-cycle fatigue life, and strength at elevated temperatures, such as combustion chamber liners and fuel injector face plates. Using powder bed fusion (PBF) 3D printing, NASA Marshall Space Flight Center (MSFC) and NASA Glenn Research Center (GRC) successfully printed near-fully-dense GRCop-42 components that may equal to or exceed their traditionally manufactured predecessors. This Technical Memorandum serves to summarize the process that was developed to achieve 3D printable near-fully-dense and functional GRCop-42.

Cooper, K. G.↗