Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLATES - BUCKLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Vibration of thermally stressed plates with various boundary conditions.

By discarding Lurie's (1952) assumption of mode identity, it is shown that linear theory correctly predicts the frequency of all modes of a thermally stressed cantilever plate as well as the frequency and modes of plates with other boundary conditions. The thermal stress distribution is obtained for whatever temperature distribution and boundary conditions that may be specified. Experimental results are compared to calculated results for several different plates. Boundary conditions for the plates range from a plate with edges completely clamped to a plate with edges completely free with various other combinations of mixed and uniform edge conditions. Comparison of calculated data to experimental data shows that accurate, quantitative results can be obtained from linear theory for 'as cut' real plates for a significant range of heating when the assumption of mode identity is discarded.

Bailey, C. D.↗
NASA NTRS1976

The nonlinear transient response of thin, rectangular elastic plates

The results of experiments and theoretical analysis of the nonlinear, transient response of thin, rectangular, elastic, simply supported plates are presented. In the experiments, a plane wave tube with a special pulse generator at one end and a thin glass plate mounted at the other end was used to subject the glass plate to pressure pulses of different magnitudes. Whole-field measurements of the response of the plate were obtained by the reflected moire grid technique. The largest ratio of center deflection to thickness of the plate during the experiments was 5.6. The theoretical response of the glass plate to the pressure pulses was computed by solving the von Karman equations governing large deflections in elastic plates by two methods - (1) the finite-difference method, and (2) Galerkin's method. Good agreement was found between theoretically predicted and experimentally measured response.

Rajagopal, G.↗
NASA NTRS1979

Design curves for non-linear analysis of simply-supported, uniformly-loaded rectangular plates

Design curves for the non-linear analysis of simply-supported rectangular plates subjected to uniform normal pressure loads have been developed. These curves yield the center deflection, center stress and corner stress in non-dimensionalized form plotted against a dimensionless parameter describing the load intensity. The results presented are based on extensive non-linear finite element analysis employing the ARGUS structural analysis program. Plates with length to width ratios of 1, 1.5, 2, 3 and 4 are included. The load range considered extends to 1000 times the load at which the behavior of the plate becomes significantly non-linear. Over the load range considered, the analysis shows that the ratio of center deflection to plate thickness for a square plate is less than 16 to 1, whereas linear theory would predict a center deflection 400 times the plate thickness. Likewise, the stress is markedly lower than would be predicted by linear theory. The present results are shown to be in excellent agreement with the classical linear theory up to a central deflection to plate thickness ratio of about one-half. In the non-linear regime the present results for deflection and stress are in very good agreement with the analytical and experimental work of other investigators.

Moore, D.↗
NASA NTRS1983

Propagating plane harmonic waves through finite length plates of variable thickness using finite element techniques

An analysis is given using finite element techniques which addresses the propagaton of a uniform incident pressure wave through a finite diameter axisymmetric tapered plate immersed in a fluid. The approach utilized in developing a finite element solution to this problem is based upon a technique for axisymmetric fluid structure interaction problems. The problem addressed is that of a 10 inch diameter axisymmetric fixed plate totally immersed in a fluid. The plate increases in thickness from approximately 0.01 inches thick at the center to 0.421 inches thick at a radius of 5 inches. Against each face of the tapered plate a cylindrical fluid volume was represented extending five wavelengths off the plate in the axial direction. The outer boundary of the fluid and plate regions were represented as a rigid encasement cylinder as was nearly the case in the physical problem. The primary objective of the analysis is to determine the form of the transmitted pressure distribution on the downstream side of the plate.

Clark, J. H.↗
NASA NTRS1983

Propagation of flexural and membrane waves with fluid loaded NASTRAN plate and shell elements

Modeling of flexural and membrane type waves existing in various submerged (or in vacuo) plate and/or shell finite element models that are excited with steady state type harmonic loadings proportioned to e(i omega t) is discussed. Only thin walled plates and shells are treated wherein rotary inertia and shear correction factors are not included. More specifically, the issue of determining the shell or plate mesh size needed to represent the spatial distribution of the plate or shell response is of prime importance towards successfully representing the solution to the problem at hand. To this end, a procedure is presented for establishing guide lines for determining the mesh size based on a simple test model that can be used for a variety of plate and shell configurations such as, cylindrical shells with water loading, cylindrical shells in vacuo, plates with water loading, and plates in vacuo. The procedure for doing these four cases is given, with specific numerical examples present only for the cylindrical shell case.

Kalinowski, A. J.↗
NASA NTRS1984

Multicolor printing plate joining

An upper plate having ink flow channels and a lower plate having a multicolored pattern are joined. The joining is accomplished without clogging any ink flow paths. A pattern having different colored parts and apertures is formed in a lower plate. Ink flow channels each having respective ink input ports are formed in an upper plate. The ink flow channels are coated with solder mask and the bottom of the upper plate is then coated with solder. The upper and lower plates are pressed together at from 2 to 5 psi and heated to a temperature of from 295 F to 750 F or enough to melt the solder. After the plates have cooled and the pressure is released, the solder mask is removed from the interior passageways by means of a liquid solvent.

Waters, W. J.↗
NASA NTRS1984

Vibrations of twisted cantilevered plates - Experimental investigation

The experimental portion of a joint government/industry/university research study on the vibrational characteristics of twisted cantilevered plates is presented. The overall purpose of the research study was to assess the capabilities and limitations of existing analytical methods in predicting the vibratory characteristics of twisted plates. Thirty cantilevered plates were precision machined at the Air Force's Aero Propulsion Laboratory. These plates, having five different degrees of twist, two thicknesses, and three aspect ratios representative of turbine engine blade geometries, were tested for their vibration mode shapes and frequencies. The resulting nondimensional frequencies and selected mode shapes are presented as a function of plate tip twist. The trends of the natural frequencies as a function of the governing geometric parameters are discussed. The effect of support compliance on the plate natural frequency and its impact on numerically modeling twisted plates is also presented.

Macbain, J. C.↗
NASA NTRS1985

An Elastic Analysis of a Plated Bone to Determine Fracture Gap Motion

An elastic analysis to determine fracture gap motions occurring in the osteotomized and plated canine femur was performed using the finite element program NASTRAN. The femur was idealized as a hollow right cylinder, and transverse anisotropy was assumed for the elastic properties of the bone. A 3-D 360 degree model consisting of 224 isoparametric quadrilateral hexahedral and 11 beam elements was created. A range of plate stiffnesses was tested by varying the modulus of elasticity of the plate from 207 GPa to 1 GPA. Moments were applied in the plane of the plate, about the axis of the plate, and in the plane of the screws. Results showed that, for plates of typical geometry and elastic modulus under 10 GPa, the contribution to fracture gap motion occurring due to deformation in the bone was negligible compared to that contribution from deformation in the plate.

Cooke, F. W.↗
NASA NTRS1985

Use of optimum stiffness tailoring to improve the compressive strength of composite plates with holes

A structural optimization procedure is used to tailor the cross-sectional stiffness distribution of compression-loaded composite plates with holes. Minimum mass designs are obtained for plates with cross sections consisting of two different balanced symmetric laminates with 0 deg, + or - 45 deg and 90 deg plies. The plate interior region contains the hole and is designed from a softer material system with a higher failure strain than the plate exterior region. All-graphite-epoxy plates and hybrid graphite/glass-epoxy plates were studied. Other designs with different percentages of 0 deg and + or 45 deg plies in the exterior laminate are compared with the optimum designs. Designs with uniform cross-sectional stiffnesses also are compared with the tailored cross-sectional stiffness designs. Specimens of each design were tested to verify the analytical predictions. The results show that cross-sectional stiffness tailoring can increase the compressive strength and decrease the mass of compression-loaded laminated plates with holes.

Haftka, R. T.↗
NASA NTRS1984

Heat transfer investigation in the junction region of circular cylinder normal to a flat plate at 90 deg location

External heat-transfer rates were measured on a flat plate in the junction region of a circular cylinder mounted normal to the plate at a location 90 deg from the stagnation point. This configuration simulates the junction of the shroud with gas-turbine vanes. Heat-transfer results are presented for laminar, transition, and turbulent boundary layers for a Mach number of 0.14 with gas temperatures of approximately 750 deg R over a flat plate at room temperature. The measurements were made in air for a unit Reynolds number, Re/cm, range of 11,000 to 58,000. Heat-transfer measurements were conducted in the 70-ft long, 4-in. diameter shock tube. A shock-wave reflection technique was used to produce a flow Mach number of 0.14. Thin-film platinum heat gages were mounted on the flat plate and along the line of the stagnation point of the cylinder to measure the local heat flux in the junction region. The experimental heat-transfer data were correlated with the laminar and turbulent boundary-layer theories for the flat plate. With the cylinder the heat fluxes on the flat plate were greatly increased in the junction region compared to the heat flux for the plate alone.

Nagamatsu, H. T.↗
NASA NTRS1987

The effects of pin elasticity, clearance, and friction on the stresses in a pin-loaded orthotropic plate

The effects of pin elasticity, clearance, and friction on the stresses in a pin loaded orthotropic plate are studied. The effects are studied by posing the problem as a planar contact elasticity problem, the pin and the plate being two elastic bodies which interact through contact. Coulomb friction is assumed, the pin loads the plate in one of its principal material directions, and the plate is infinite in extent. A collocation scheme and interaction, in conjunction with a complex variable series solution, are used to obtain numerical results. The contact region between the plate and pin is unknown and must be solved for as part of the solution. The same is true of the region of friction induced no slip. Two pin stiffnesses, two clearance levels, two friction levels and two laminates, a (0/+ or - 45/90)s and a (02/+ or - 45)s, are studied. The effects of pin elasticity, clearance, and friction on the load capacity of the plate are assessed by comparing the load capacity of the plate with the capacity when the pin is rigid, perfectly fitting, and frictionless.

Hyer, M. W.↗
NASA NTRS1988

Impact induced stresses, strains, and delaminations in composite plates

A method is presented for calculating the locations and sizes of delaminations which occur in a rectangular, fiber reinforced composite plate subjected to nonpenetrating (low velocity) impact of a solid object. The plate may be simply supported or clamped along its edges. In-plane loads or in-plane strains may be imposed on the plate during the impact. The method includes two steps. First, the stresses and strains in the plate are calculated by a three-dimensional, transient finite element method using 8-node brick elements with incompatible modes. Second, the locations, lengths, and widths of delaminations inside the plate are predicted by means of a proposed failure criterion, which is based on the concept of dimensional analysis. The finite element method and the failure criterion were implemented by a computer code which can be used to calculate the impactor position and velocity, the displacements of the plate, the stresses and strains inside the plate during the impact, and the locations and dimensions of the delaminations after the impact. Parametric studies were performed to illustrate the information which can be generated by the computer code.

Wu, Hsi-Yung T.↗
NASA NTRS1990

Current plate motions

A global plate motion model, named NUVEL-1, which describes current plate motions between 12 rigid plates is described, with special attention given to the method, data, and assumptions used. Tectonic implications of the patterns that emerged from the results are discussed. It is shown that wide plate boundary zones can form not only within the continental lithosphere but also within the oceanic lithosphere; e.g., between the Indian and Australian plates and between the North American and South American plates. Results of the model also suggest small but significant diffuse deformation of the oceanic lithosphere, which may be confined to small awkwardly shaped salients of major plates.

Demets, C.↗
NASA NTRS1991

Convection in three dimensions with surface plates - Generation of toroidal flow

This work presents numerical calculations of mantle convection that incorporate some of the basic observational constraints imposed by plate tectonics. The model is three-dimensional and includes surface plates; it allows plate velocity to change dynamically according to the forces which result from convection. It is shown that plates are an effective means of introducing a toroidal component into the flow field. After initial transients the plate motion is nearly parallel to transform faults and in the direction that tends to minimize the toroidal flow field. The toroidal field decays with depth from its value at the surface; the poloidal field is relatively constant throughout the layer but falls off slightly at the top and bottom boundaries. Layered viscosity increasing with depth causes the toroidal field to decay more rapidly, effectively confining it to the upper, low-viscosity layer. The effect of viscosity layering on the poloidal field is relatively small, which is attributed to its generation by temperature variations distributed throughout the system. The generation of toroidal flow by surface plates would seem to account for the observed nearly equal energy of toroidal and poloidal fields of plate motions on the earth. A low-viscosity region in the upper mantle will cause the toroidal flow to decay significantly before reaching the lower mantle. The resulting concentration of toroidal flow in the upper mantle may result in more thorough mixing there and account for some of the geochemical and isotopic differences proposed to exist between the upper and lower mantles.

Gable, Carl W.↗
NASA NTRS1992

Postbuckling of multilayered composite plates subjected to combined axial and thermal loads

A study is made of the postbuckling response of composite plates subjected to combined axial and thermal loadings. The analysis is based on a first-order shear deformation, von Karman type of nonlinear plate theory. A mixed formulation is used with the fundamental unknowns consisting of the generalized displacements and the stress resultants of the plate. An efficient reduction method is used in conjunction with mixed finite element models for determining the stability boundary and the postbuckling response of the plate. Sensitivity derivatives are evaluated and used to study the sensitivity of the postbuckling response to variations in the different lamination and material parameters of the plate. For quasi-isotropic plates, numerical results are presented showing the effects of variations in the material characteristics and fiber orientation of individual layers on the postbuckling response of the plate.

Noor, Ahmed K.↗
NASA NTRS1992

Stress observations and driving force models for the South American plate

A comparison of stress observations to predictions of driving force models for the South American plate is presented. Conditions for dynamical equilibrium are used to estimate the magnitudes of forces as a function of age, with ridge push and slab pull as active forces, and plate drag and slab resistance as passive forces. The results are consistent with earlier published models, and it is found that the primary balance for an oceanic plate is between slab pull and the resisting drag forces. The model is generalized for the possible forces driving the South American plate, and it is compared with observed stress measurements and kinematics. The plate balance is found to be largely between ridge push and plate drag. The magnitude of a possible trench suction force is estimated using a model with an eddy between the Nazca slab and the overlying South American plate.

Stefanick, Michael↗
NASA NTRS1993

Modeling of composite beams and plates for static and dynamic analysis

The main purpose of this research was to develop a rigorous theory and corresponding computational algorithms for through-the-thickness analysis of composite plates. This type of analysis is needed in order to find the elastic stiffness constants for a plate and to post-process the resulting plate solution in order to find approximate three-dimensional displacement, strain, and stress distributions throughout the plate. This also requires the development of finite deformation plate equations which are compatible with the through-the-thickness analyses. After about one year's work, we settled on the variational-asymptotical method (VAM) as a suitable framework in which to solve these types of problems. VAM was applied to laminated plates with constant thickness in the work of Atilgan and Hodges. The corresponding geometrically nonlinear global deformation analysis of plates was developed by Hodges, Atilgan, and Danielson. A different application of VAM, along with numerical results, was obtained by Hodges, Lee, and Atilgan. An expanded version of this last paper was submitted for publication in the AIAA Journal.

Hodges, Dewey H.↗
NASA NTRS1993

Development efforts to improve curved-channel microchannel plates

Curved-channel microchannel plate (C-plate) improvements resulting from an ongoing NASA STIS microchannel plate (MCP) development program are described. Performance limitations of previous C-plates led to a development program in support of the STIS MAMA UV photon counter, a second generation instrument on the Hubble Space Telescope. C-plate gain, quantum detection efficiency, dark noise, and imaging distortion, which are influenced by channel curvature non-uniformities, have all been improved through use of a new centrifuge fabrication technique. This technique will be described, along with efforts to improve older, more conventional shearing methods. Process optimization methods used to attain targeted C-plate performance goals will be briefly characterized. Newly developed diagnostic measurement techniques to study image distortion, gain uniformity, input bias angle, channel curvature, and ion feedback, will be described. Performance characteristics and initial test results of the improved C-plates will be reported. Future work and applications will also be discussed.

Corbett, M. B.↗