Search NASA⌕ Search

SEARCH · Search NASA

Results for “POLYAMIDES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Uranium Removal from Seawater by Means of Polyamide 6 Fibers Directly Grafted with Diallyl Oxalate through a Single-Step, Solvent-Free Irradiation Process

In order to test the effectiveness of oxalate-based polymeric adsorbents in the recovery of uranium from seawater, diallyl oxalate (DAOx) was grafted onto nylon 6 fabrics by exposing the fabric, immersed in pure liquid DAOx or in a surfactant-stabilized dispersion of DAOx in water, to electron beam or gamma radiation. Following drying and weighing to determine the degree of grafting (DoG), the presence of oxalate in the fabrics was verified using XPS. Zeta potential measurements showed the fabric surfaces to be negatively charged. The fabrics were tested by rotating them for 7 days in a rotary agitator with actual seawater spiked with 0.2 or 1.0 mg∙L -1 uranium. The fraction of uranium in the solution which was removed due to uptake on the fabrics was found to rise with increasing DoG at both uranium concentrations. EDS measurements were used to map the distribution of adsorbed uranium on the polymeric fibers.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Multicolor polymeric carbon dots: synthesis, separation and polyamide-supported molecular fluorescence

Multicolor carbon dots (CDs) have been developed recently and demonstrate great potential in bio-imaging, sensing, and LEDs. However, the fluorescence mechanism of their tunable colors is still under debate, and efficient separation methods are still challenging. Herein, we synthesized multicolor polymeric CDs through solvothermal treatment of citric acid and urea in formamide. Automated reversed-phase column separation was used to achieve fractions with distinct colors, including blue, cyan, green, yellow, orange and red. This work explores the physicochemical properties and fluorescence origins of the red, green, and blue fractions in depth with combined experimental and computational methods. Three dominant fluorescence mechanism hypotheses were evaluated by comparing time-dependent density functional theory and molecular dynamics calculation results to measured characteristics. We find that blue fluorescence likely comes from embedded small molecules trapped in carbonaceous cages, while pyrene analogs are the most likely origin for emission at other wavelengths, especially in the red. Also important, upon interaction with live cells, different CD color fractions are trafficked to different sub-cellular locations. Super-resolution imaging shows that the blue CDs were found in a variety of organelles, such as mitochondria and lysosomes, while the red CDs were primarily localized in lysosomes. These findings significantly advance our understanding of the photoluminescence mechanism of multicolor CDs and help to guide future design and applications of these promising nanomaterials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Polyamides based on the renewable monomer, 1,13-tridecane diamine I: synthesis and characterization of nylon 13,T

Nylon 13,T was successfully synthesized and chemical composition, thermal properties, crystal structure, and moisture absorption characterized. Melting temperature and glass transition temperature were determined to be 263 °C and 90 °C, respectively, while the equilibrium melting temperature was determined to be 289 °C. Characterization of the crystallization kinetics showed that nylon 13,T exhibits very fast crystallization compared to the industrially important nylons, nylon 6 and nylon 6,6. In addition, the moisture absorption of nylon 13,T was dramatically lower than nylon 6 and nylon 6,6 which is consistent with the much lower amide content of nylon 13,T. The crystal structure was determined to be pseudohexagonal.

36 MATERIALS SCIENCE↗

Literature Review of Recycling Polypropylene and Polyamide 12 Powders for Selective Laser Sintering

Additive manufacturing (AM) is the creation of three-dimensional parts by adding material layer-by-layer based on two dimensional “slices” of a CAD file, without molds or tooling. AM has broken the relationship between part complexity and manufacturing cost. As a general rule, for conventional manufacturing, the more complex the part produced, the more costly its manufacturing. For example, in the production of a bracket for a satellite, moving from conventional manufacturing to AM allowed the part to be consolidated from 4 parts to just one, as well as reducing the weight of the part by 35%. A further benefit, AM can be more cost effective for small lot sizes. To illustrate, consider a case study of white board marker caps presented by Klahn et al. The cost to produce 1,000 units of a new design using SLS was about an order of magnitude lower than conventional manufacturing, as shown in Figure 1.

36 MATERIALS SCIENCE↗

Chemical treatment makes aromatic polyamide fabric fireproof in oxygen atmosphere

Organic fabric is reacted first with vapors of a phosphorus oxychloride, phosphorus oxybromide solution and then with bromine vapor, after neutralization it is flameproof in pure oxygen atmosphere. Soaking the fabric with mixture of ammonium polyphosphates increases flame resistance, but the polyphosphates are leached out during laundering.

Cardwell, R. O.↗

High-performance vessels from an aromatic polyamide fiber/epoxy composite

The investigation reported is concerned with the development of a filament-wound, ultralightweight composite vessel for the containment of cryogenic propellants and pressurant gases. The vessels are to be used within an operational temperature range from -253 C to ambient temperature. The fiber used for the process is Kevlar 49. The design and the fabrication of specimens and vessels are discussed along with the results obtained in a testing program.

Chiao, T. T.↗

Polyamide-Imides Made From BTDA

New synthesis results in improved class of tough, thermally stable polyimides containing amide linkages. Linear, aromatic, polyimide/amides synthesized from isomers of DABA with 3, 3', 4, 4'- BTDA. Mechanical properties better than those of LARC-TPI polyimide. Potentially useful as matrix resins in graphite-reinforced structures, and as fibers or coating films withstanding high temperatures.

Dezern, James F.↗

Quantitative Characterization of a Desalination Membrane Model System by X-ray Photoelectron Spectroscopy

Aromatic polyamide films form the active layer in reverse osmosis desalination membranes. Despite widespread use of this technology, it suffers from low rejection rates for certain water contaminants and from membrane fouling. Through a better understanding of the fundamental surface chemical processes during reverse osmosis desalination, advances in membrane and material design are expected. The recent invention of a molecular layer-by-layer (mLbL) preparation technique yields films that are sufficiently smooth to warrant investigation with high-resolution microscopy and spectroscopy methods. In this study, we present high-resolution, quantitative X-ray photoelectron spectroscopy (XPS) data on the surface chemistry of ultrathin polyamide films that can serve as a model system for desalination membranes. We show that a quantitative analysis of the XPS spectra gives information about the functional groups of the film as well as other compounds present due to the synthesis under ambient conditions. Unpolymerized functional groups are identified and aid in understanding the degree of cross-linking. Investigation of polymers with synchrotron-based XPS requires taking beam-induced changes into account. We quantify X-ray beam damage and show that beam damage to the polyamide is limited, allowing long-term investigation of thin polyamide films. Characterizing mLbL-grown films via high-resolution XPS is the basis for a better understanding of the chemical interplay of polyamide surface functional groups with the major components of desalination systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Influence of Fiber Orientation on Deformation of Additive Manufactured Composites

Anisotropy caused by flow-induced fiber orientation of discontinuous fibers within the extrudate in the Extrusion Deposition Additive Manufacturing (EDAM) process gives rise to anisotropic shrinkage in printed parts and thereby, final part deformations. Three fiber orientation states, described by the second-order orientation tensor, were investigated to determine their influence upon final geometry. Two material systems were investigated including a short glass fiber-reinforced polyamide and a short carbon fiber-reinforced polyamide. A curvilinear geometry was modeled and printed virtually in the thermo-mechanical simulation, ADDITIVE3D©. The scale of the printed geometry was in the range of 300–400 mm and contained three semicircular geometry regions connected to linear regions, thereby inducing significant magnification of the spring-in deformation. The predicted deformation of the printed geometry for the three fiber orientation states and two material systems were compared. The deformation predicted for glass fiber-filled polyamide and carbon fiber-filled polyamide of the same fiber orientation states showed comparable deformations. In conclusion, the largest residual deformation was shown to correspond to the orientation tensor with the greatest degree of anisotropy.

36 MATERIALS SCIENCE↗