SEARCH · Search NASA

Results for “PROPAGATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Extension of Clad Damage Propagation Model for Fission Gas Dispersal and Two-Phase Flow Effects in MOOSE SubChannel Module

This report presents an extension of the Clad Damage Propagation (CDAP) model implemented in the MOOSE SubChannel Module (SCM) to capture post-failure fission-gas dispersal and two-phase flow effects in sodium-cooled fast reactor assemblies. The extended model tracks discharged gas axially and radially, computes channel-averaged flow quality and void fraction using a Lockhart–Martinelli framework, evaluates two-phase frictional pressure-drop multipliers, determines inlet mass-flow degradation under fixed core pressures, and applies an intensified-void-based heat-transfer degradation to affected fuel pins. Radial plume expansion is parameterized using mineral-oil jet experiments mapped to sodium conditions via Reynolds–Weber similarity. Implementation details are documented, along with the new methods and user inputs needed to control plume mapping and two-phase behavior. Demonstration simulations for 19- and 37-pin bundles show that breach size and inlet velocity strongly influence propagation potential: small breaches (≤0.5 mm) produce limited degradation while larger breaches (~1 mm) can drive oscillatory temperature spikes and enhanced failure propagation, especially at higher velocities. These results demonstrate that the extended CDAP model provides a more complete framework for quantifying cladding damage propagation and evaluating propagation potential in transient scenarios. The approach remains computationally efficient, consistent with subchannel-level analysis, yet incorporates sufficient physics to bridge localized post-failure effects with bundle- and assembly-scale degradation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1972

Fatigue crack tip deformation and fatigue crack propagation

The effects of stress ratio, prestress cycling and plate thickness on the fatigue crack propagation rate are studied on 2024-T351 aluminum alloy. Fatigue crack propagation rate increases with the plate thickness and the stress ratio. Prestress cycling below the static yield strength has no noticeable effect on the fatigue crack propagation rate. However, prestress cycling above the static yield strength causes the material to strain harden and increases the fatigue crack propagation rate. Crack tip deformation is used to study the fatigue crack propagation. The crack tip strains and the crack opening displacements were measured from moire fringe patterns. The moire fringe patterns were obtained by a double exposure technique, using a very high density master grille (13,400 lines per inch).

Kang, T. S.↗

NASA NTRS1974

Millimeter wavelength propagation studies

The investigations conducted for the Millimeter Wavelength Propagation Studies during the period December, 1966, to June 1974 are reported. These efforts included the preparation for the ATS-5 Millimeter Wavelength Propagation Experiment and the subsequent data acquisition and data analysis. The emphasis of the OSU participation in this experiment was placed on the determination of reliability improvement resulting from the use of space diversity on a millimeter wavelength earth-space communication link. Related measurements included the determination of the correlation between radiometric temperature and attenuation along the earth-space propagation path. Along with this experimental effort a theoretical model was developed for the prediction of attenuation statistics on single and spatially separated earth space propagation paths. A High Resolution Radar/Radiometer System and Low Resolution Radar System were developed and implemented for the study of intense rain cells in preparation for the ATS-6 Millimeter Wavelength Propagation Experiment.

Hodge, D. B.↗

NASA NTRS1978

Propagation of a laser beam in a time-varying waveguide

The propagation of an axisymmetric laser beam in a plasma column having a radially parabolic electron density distribution is reported. For the case of an axially uniform waveguide it is found that the basic characteristics of alternating focusing and defocusing beams are maintained. However, the intensity distribution is changed at the foci and outer-beam regions. The features of paraxial beam propagation are discussed with reference to axially varying waveguides. Laser plasma coupling is considered noting the case where laser heating produces a density distribution radially parabolic near the axis and the energy absorbed over the focal length of the plasma is small. It is found that: (1) beam-propagation stability is governed by the relative magnitude of the density fluctuations existing in the axial variation of the waveguides due to laser heating, and (2) for beam propagation in a time-varying waveguide, the global instability of the propagation is a function of the initial fluctuation growth rate as compared to the initial time rate of change in the radial curvature of the waveguide.

Chapman, J. M.↗

NASA NTRS1980

Radio propagation through solar and other extraterrestrial ionized media

The present S- and X-band communications needs in deep space are addressed to illustrate the aspects which are affected by propagation through extraterrestrial plasmas. The magnitude, critical threshold, and frequency dependence of some eight propagation effects for an S-band propagation path passing within 4 solar radii of the Sun are described. The theory and observation of propagation in extraterrestrial plasmas are discussed and the various plasma states along a near solar propagation path are illustrated. Classical magnetoionic theory (cold anisotropic plasma) is examined for its applicability to the path in question. The characteristics of the plasma states found along the path are summarized and the errors in some of the standard approximations are indicated. Models of extraterrestrial plasmas are included. Modeling the electron density in the solar corona and solar wind, is emphasized but some cursory information on the terrestrial planets plus Jupiters is included.

Smith, E. K.↗

NASA NTRS1981

Propagation in a shearing plasma. III - Magnetic field effects and pulsar microstructure periods

Effects of a magnetic field on wave and pulse propagation in a shearing plasma are investigated. Equations for the wave fields are derived from Maxwell's equations and the Minkowski relations for an anisotropic medium, when the magnetic field is parallel to the shearing velocity. The independent propagation modes are elliptically polarized in the stationary frame and vary with the velocity of the medium. Numerical calculations are presented which show the propagation of waves and pulses through a plane-parallel shearing plasma in the case of weak and strong fields. It is found that in a weak field, propagation effects are very similar to those previously found in field-free models: the transmitted pulses acquire temporal modulations whose period is frequency dependent. In a strong field, the period of the temporal modulations is independent of frequency. Transmitted pulses can also undergo polarization changes as a result of phase differences between modes. These results are discussed in relation to their significance to propagation in a pulsar magnetosphere and, in particular, to a model for pulse microstructure.

Harding, A. K.↗

NASA NTRS1985

Evaluation of the feasibility of scale modeling to quantify wind and terrain effects on low-angle sound propagation

The feasibility of acoustical scale modeling techniques for modeling wind effects on long range, low frequency outdoor sound propagation was evaluated. Upwind and downwind propagation was studied in 1/100 scale for flat ground and simple hills with both rigid and finite ground impedance over a full scale frequency range from 20 to 500 Hz. Results are presented as 1/3-octave frequency spectra of differences in propagation loss between the case studied and a free-field condition. Selected sets of these results were compared with validated analytical models for propagation loss, when such models were available. When they were not, results were compared with predictions from approximate models developed. Comparisons were encouraging in many cases considering the approximations involved in both the physical modeling and analysis methods. Of particular importance was the favorable comparison between theory and experiment for propagation over soft ground.

Anderson, G. S.↗

NASA NTRS1986

Dynamic delamination crack propagation in a graphite/epoxy laminate

The dynamic delamination crack propagation behavior during ballistic tests of (90/0)5s T-300/934 graphite/epoxy laminates with embedded interfacial cracks was investigated using high speed photography. The impact on the beam-like specimen was produced with a silicon rubber ball, and the crack propagation speeds and the threshold impact velocities required to initiate dynamic crack propagation were determined for several crack positions. The results suggest that the mode of crack propagation depends on the specimen geometry as well as the loading condition. A simplified finite element analysis of the experimental data obtained from one of the midplane-cracked specimens was used to estimate the critical strain energy release rate, which may determine the onset of unstable crack propagation.

Sun, C. T.↗

NASA NTRS1986

Systematic errors in determining the propagation direction of interplanetary Alfvenic fluctuations

Analyses of Alfvenic fluctuations in the solar wind contain a systematic effect in which outward propagation is favored. The effect is generally small at and beyond 1 AU in a Mach 10 flow but can become important where the Mach number is lower, e.g., inside 1 AU. If the propagation speeds of the inward and outward propagating Alfvenic fluctuations are properly included, this systematic effect can be removed. A technique for doing this is illustrated using both artificial and spacecraft data. The results suggest that time intervals originally thought to be outward propagating sometimes contain wave number bands in the cross helicity spectrum of inward propagating Alfvenic fluctuations.

Goldstein, M. L.↗

NASA NTRS1986

Relationship between directions of wave and energy propagation for cold plasma waves

The dispersion relation for plasma waves is considered in the 'cold' plasma approximation. General formulas for the dependence of the phase and group velocities on the direction of wave propagation with respect to the local magnetic field are obtained for a cold magnetized plasma. The principal cold plasma resonances and cut-off frequencies are defined for an arbitrary angle and are used to establish basic regimes of frequency where the cold plasma waves can propagate or can be evanescent. The relationship between direction of wave and energy propagation, for cold plasma waves in hydrogen atmosphere, is presented in the form of angle diagrams (angle between group velocity and magnetic field versus angle between phase velocity and magnetic field) and polar diagrams (also referred to as 'Friedrich's diagrams') for different directions of wave propagation. Morphological features of the diagrams as well as some critical angles of propagation are discussed.

Musielak, Zdzislaw E.↗

NASA NTRS1988

The Effect of Gravity on Premixed Flame Propagation and Extinction in a Vertical Standard Flammability Tube

The effect of gravity on the upward and downward flame propagation in lean methane/air and lean propane/air mixtures was studied using plexiglass flammability tubes with ignition at the open-end gravity levels which ranged from microgravity (0 + or - 0.1 g) to 1.77 g. The lean limits were found to be about 5.25, 5.25, and 5.85 percent methane in air; and about 2.15, 2.06, and 2.20 percent propane in air for 1 g upward propagation, 0 g, and 1 g downward propagation, respectively. The propane/air flames observed were stable, irrespective of the g level. On the other hand, lean methane/air flames were found to be sporadically unstable for upward propagation at g levels less than 0.5 g, and for donward propagation at g = 1.0. The extinction process observed was the same for both systems studied: at g = 0, the flame extinguished from the edge toward the center, while at g of 1 and above, the flame extinguished from the center toward the edge.

Strehlow, Roger A.↗

NASA NTRS1987

Low-frequency acoustic propagation in high winds

The effect of refraction due to wind gradients on low-frequency acoustic signals over large propagation distances is considered. The results of an investigation of low-frequency propagation in high winds are presented and compared to normal mode theory for the downwind propagation case. In the downwind direction, the low-frequency signal was channeled close to the ground resulting in a divergence of 3 dB per doubling of propagation distance. Predictions of both ray tracing and normal mode theoretical models supported the downwind cylindrical spreading. In effect, the low-frequency noise signals propagate further in the presence of wind in the downwind direction. No low-frequency acoustic shadow zone was observed in the upwind direction.

Willshire, William L., Jr.↗

NASA NTRS1989

Proceedings of the Thirteenth NASA Propagation Experimenters Meeting (NAPEX 13)

The NASA Propagation Experimenters Meeting (NAPEX), supported by the NASA Propagation Program, is convened annually to discuss studies made on radio wave propagation by investigators from domestic and international organizations. The meeting was organized into three technical sessions: the first focused on mobile satellite propagation; the second examined the propagation effects for frequencies above 10 GHz; and the third addressed studies devoted exclusively to the Olympus/Advanced Communications Technology Satellite (ACTS) Program.

Davarian, Faramaz↗

NASA NTRS1989

Propagation and absorption of electron-cyclotron maser radiation during solar flares

The propagation and absorption of the maser radiation during solar flares are examined through linear theory and electromagnetic particle simulations. It is shown using linear theory that strong absorption of the radiation should occur as it propagates toward the second harmonic layer, where the magnetic field is half as strong as in the emission region. Only radiation propagating nearly parallel to the magnetic field in a low-temperature plasma may be able to escape under certain limited conditions. Finite temperature effects can cause radiation propagating nearly perpendicular to the magnetic field to refract, causing enhanced absorption. Particle simulations are then used to evaluate the nonlinear response of the plasma as the maser radiation propagates through the absorption layer. It is shown that some of the maser radiation is able to escape through a process of absorption below the second harmonic of the local gyrofrequency and re-emission above it. The fraction able to escape is much higher than that predicted by linear theory, although the amount of escaping energy is only a small fraction of the incident energy.

Mckean, M. E.↗

NASA NTRS1991

Dynamic delamination crack propagation in a graphite/epoxy laminate

Dynamic delamination crack propagation in a (90/0) 5s Graphite/Epoxy laminate with an embedded interfacial crack was investigated experimentally using high speed photography. The dynamic motion was produced by impacting the beamlike laminate specimen with a silicon rubber ball. The threshold impact velocities required to initiate dynamic crack propagation in laminates with varying initial crack positions were determined. The crack propagation speeds were estimated from the photographs. Results show that the through the thickness position of the embedded crack can significantly affect the dominant mechanism and the threshold impact velocity for the onset of crack movement. If the initial delamination is placed near the top of bottom surface of the laminate, local buckling of the delaminated plies may cause instability of the crack. If the initial delamination lies on the midplane, local buckling does not occur and the initiation of crack propagation appears to be dominated by Mode II fracture. The crack propagation and arrest observed was seen to be affected by wave motion within the delamination region.

Grady, J. E.↗

NASA NTRS1993

A numerical study of wave propagation in a confined mixing layer by eigenfunction expansions

It is well known that the growth rate of instability waves of a two-dimensional free shear layer is reduced greatly at supersonic convective Mach numbers. In previous works, it has been shown that new wave modes exist when the shear layers are bounded by a channel due to the coupling effect between the acoustic wave modes and the motion of the mixing layer. The present work studies the simultaneous propagation of multiple stability waves using numerical simulation. It is shown here that the coexistence of two wave modes in the flow field can lead to an oscillatory growth of disturbance energy with each individual wave mode propagating linearly. This is particularly important when the growth rates of the unstable waves are small. It is also shown here that the propagation of two neutrally stable wave modes can lead to a stationary periodic structure of rms fluctuations. In the numerical simulations presented here the forced wave modes are propagating at same frequency, but with different phase velocities. In order to track the growth of each wave mode as it propagates downstream, a numerical method that can effectively detect and separate the contribution of the individual wave is given. It is demonstrated that by a least square fitting of the disturbance field with eigenfunctions the amplitude of each wave mode can be found. Satisfactory results as compared to linear theory are obtained.

Hu, Fang Q.↗

NASA NTRS1993

User needs for propagation data

New and refined models of radio signal propagation phenomena are needed to support studies of evolving satellite services and systems. Taking an engineering perspective, applications for propagation measurements and models in the context of various types of analyses that are of ongoing interest are reviewed. Problems that were encountered in the signal propagation aspects of these analyses are reviewed, and potential solutions to these problems are discussed. The focus is on propagation measurements and models needed to support design and performance analyses of systems in the Mobile-Satellite Service (MSS) operating in the 1-3 GHz range. These systems may use geostationary or non-geostationary satellites and Frequency Division Multiple Access (FDMA), Time Division Multiple Access Digital (TDMA), or Code Division Multiple Access (CDMA) techniques. Many of the propagation issues raised in relation to MSS are also pertinent to other services such as broadcasting-satellite (sound) at 2310-2360 MHz. In particular, services involving mobile terminals or terminals with low gain antennas are of concern.

Sullivan, Thomas M.↗

NASA NTRS1995

Modeling and numerical simulation of microwave pulse propagation in air breakdown environment

It is shown that ionization occurs wherever the field intensity of the pulse exceeds the local breakdown threshold field of the background air. The produced plasma then attenuates the pulse and gives rise to a tail erosion phenomenon that plays the primary role in limiting the energy transfer of the pulse from source to destination. A theoretical model describing the propagation of an intense microwave pulse in an air breakdown environment is developed that includes the possible focusing effect introduced by either using phase array antennas or the other arrangements. The self-consistent description of the propagation process is provided by a set of two modal equations. These include a continuity equation (Poynting's equation) for the energy density of the pulse and a rate equation of the electron density. A forward wave approximation is used to simplify Poynting's equation, and a semiempirical formula is used for the ionization frequency, nu(sub i). This frequency provides the coupling between the two modal equations, and is used to express the electron rate equation explicitly. In terms of the relevant parameters of the atmosphere, these two equations are normalized for numerical analysis of pulse propagation in the atmosphere. The dependencies of the propagation characteristics of the pulse on intensity, frequency, width, and shape of the pulse are determined. The numerical simulations lead to a useful empirical relation p(exp 3)w = alpha = constant, where p and w are the incident power and width of the pulse and alpha depends on the percentage of pulse energy transferred from the source point to a destined position. The density distribution of the pulse's self-generated plasma is also evaluated. The results also show that for ionization caused by a single unfocused microwave pulse transmitted upwards from the ground, the maximum electron density produced at, for example, 50 km altitude is limited by the tail erosion effect to below 10(exp 6) cm(exp -3). Repetitive pulse and focused beam approaches are also examined. Both approaches can increase the maximum electron density by no more than an order of magnitude. A scheme using two obliquely propagating pulses intersecting at the destined height, e.g. 50 km, is considered. It is shown that the electron density generated at the lowest intersecting position can easily reach a value of 6.6 x 10(exp 8) cm(exp -3), which is considered to be high enough for artificial ionospheric mirror (AIM) application.

Kim, J.↗