Search NASA⌕ Search

SEARCH · Search NASA

Results for “Polyethylene”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Enhanced Stability and Sensitivity for CA-125 Detection Under Microfluidic Shear Flow Using Polyethylene Glycol-Coated Biosensor

The microfluidic-based point-of-care (POC) diagnostic tool has garnered significant interest in recent years, offering rapid and cost-effective disease detection. There is a growing trend toward integrating microfluidic platforms with biosensors, aligning lab-on-a-chip technologies with POC diagnostic devices. Despite numerous efforts to incorporate biosensors into microfluidic systems, researchers have performed very limited investigations on the stability of biomarker detection when biosensors operate under microfluidic shear flow conditions. Gold nanoparticles (AuNPs) are a widely employed material in capacitive biosensors for antibody immobilization and sensitivity enhancement. However, AuNPs have limitations in providing stable detection of biomarkers within microfluidic shear flow due to their agglomeration nature. This study addresses these limitations by employing 2 kDa polyethylene glycol (PEG) as an intermediate biofunctional layer to immobilize CA-125 antibodies on gold-interdigitated electrodes for the stable and accurate detection of CA-125 antigens. The stabilities and sensitivities of AuNPs and PEG-coated biosensors are evaluated under both static drop and microfluidic shear flow conditions for CA-125 antigen detection. The experimental results demonstrate a capacitive signal response (5660 pF at 10 kHz) 2.2 times higher using the PEG-coated biosensor than the signal (2551 pF at 10 kHz) measured by the AuNP-coated biosensor in the detection of CA-125 antigen–antibody conjugation under static drop conditions, indicating the higher sensitivity of the PEG-coated biosensor. Additionally, the PEG-coated biosensor exhibits better consistency for the CA-125 antigen detection between static drop and microfluidic shear flow conditions (Cp decrease in percentage (ΔCp%↓) = 2.9% at 10 kHz) compared to the electrical signals measured using the AuNP-coated biosensor (ΔCp%↓ = 32.4% at 10 kHz), which suggests that the PEG-coated biosensor demonstrates higher stability for CA-125 antigen detection under microfluidic shear flow conditions. With these significant improvements brought by the PEG-coated biosensor, especially under microfluidic conditions, a substantial hurdle in developing electrical biosensors for POC diagnostic applications has been overcome, expediting further advancements in the field.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Hydrogen Production from Polyethylene Pyrolysis

Hydrogen is anticipated to play a pivotal role in the future of clean energy and decarbonization efforts, serving as an energy storage medium, a power generation source, and a clean fuel for transportation. While most hydrogen is produced from carbonaceous fossil feedstocks like natural gas, petroleum, and coal, there is growing interest in using refuse-derived fuels such as waste plastics and municipal solid waste (MSW) as alternative feedstocks. Thermochemical processes such as pyrolysis and catalytic cracking can convert nonrecyclable plastics and organic MSW components to produce hydrogen with lower life cycle greenhouse gas emissions when coupled with CO 2 capture. Such approaches not only address waste-management challenges but also reduce methane emissions from landfills. Furthermore, waste feedstocks are low cost and can support meeting demands for hydrogen across various industries. In this work we examined production of hydrogen from high-density polyethylene (HDPE) as a model polymer using pyrolysis. Analytical studies of pyrolysis utilizing gas chromatography–mass spectrometry (GC/MS) provide insights into conversion pathways for plastic waste, potentially reducing the environmental footprint of traditional hydrogen production methods. This work generates a baseline methodology for hydrogen production from plastic pyrolysis with and without a catalyst and the necessary product distribution baseline from key single plastics. The effect of pyrolysis temperature on the conversion of HDPE was evaluated both with and without a catalyst(s), and the product distributions measured via GC/MS were identified and hydrogen formation was quantified. These results will help guide future research efforts to optimize catalysts and processes for more efficient hydrogen production and mixed plastic waste management.

Catalysts↗
DOE OSTI2025

One-Step Radical-Induced Synthesis of Graft Copolymers for Effective Compatibilization of Polyethylene and Polypropylene

The synthesis of copolymers from high-density polyethylene (HDPE) and isotactic polypropylene (iPP) has gained increasing attention due to their ability to improve the recycling of incompatible mixed polyolefin waste feed streams. Herein, we report a new radical grafting process that yields HDPE-g-iPP copolymers from HDPE and iPP by using a commercially available peroxide. Tensile testing of brittle 70/30 HDPE/iPP mixtures with these graft copolymers added showed promising compatibilization, improving the elongation at break of the blends from 20% up to 1080%. Detailed kinetic studies coupled with thermal and rheological characterization revealed optimized conditions for HDPE and iPP macroradical coupling and a deeper understanding of the grafting reaction. This optimization yielded HDPE-g-iPP copolymers that compatibilize HDPE and iPP blends at loadings as low as 2.5 wt %. In conclusion, the versatility of this macroradical grafting reaction was demonstrated by preparing an effective compatibilizer from untreated postconsumer waste plastics.

compatibilization↗
DOE OSTI2026

Positional Isomer of P3HB by Stereoselective Polymerization of Racemic α-Methyl-β-propiolactone Delivers Polyethylene-like Properties

Biobased and biodegradable poly(3-hydroxybutyrolactone) (P3HB) has long been considered as a more sustainable alternative to petroleum-based, nonbiodegradable polyolefins, but its properties are far off from its polyolefin (polyethylene, PE, and polypropylene, PP) counterpart’s unique set of thermal (low T g below −20 °C and high T m > 100 °C) and mechanical (high ductility >350%) characteristics. Here, we report that a positional isomer of P3HB, poly(3-hydroxy-2-methylpropionate) (P3H2MP), synthesized by catalyst-controlled stereoselective polymerization of racemic α-methyl-β-propiolactone, can match that demanding set of thermomechanical properties of PE. In particular, isotactic-rich P3H2MP, readily synthesized under ambient conditions, reaches high M n close to one million Da, T g down to −25 °C, T m up to 115 °C, tensile strength up to 64 MPa, and toughness up to 131 MJ m –3 , thus mechanically outperforming PE while maintaining a comparable low T g and high T m combination. A P3H2MP-based triblock copolymer further widens the low-high temperature window from T g = −29 °C to T m = 186 °C, resembling those of PP. These results show that P3H2MP exhibits the unique combination of thermomechanical properties matching those of high-performance polyolefins.

Biopolymers↗
DOE OSTI2026

Effects of Polymer Morphology on Solvent and Catalyst Accessibility during Polyethylene and Polystyrene Autoxidation

Efficient catalytic deconstruction of plastics requires facile solvent and catalyst access to polymer substrates to minimize mass transfer effects. Autoxidation using Co(II) acetate, Mn(II) acetate, and a radical carrier in acetic acid is a promising strategy to deconstruct mixed plastic waste, yet the role of polymer morphology in governing solvent and catalyst accessibility remains poorly understood. Here, in situ simultaneous small- and wide-angle X-ray scattering (SAXS/WAXS), complemented by X-ray fluorescence (XRF) imaging and high-pressure differential scanning calorimetry (DSC), were used to elucidate interactions between acetic acid, a Co/Mn catalyst solution, and semicrystalline polyethylene (PE) and amorphous polystyrene (PS) from room temperature to 160 °C. In PE, acetic acid and catalyst access were confined to amorphous regions and cryomilled particle interfaces at room temperature, while crystalline lamellae remained intact after soaking for up to 34 h. Increasing temperature enabled solvent uptake into PE, followed by solvent-assisted softening above 100 °C, and a modest melting-point depression that removed lamellar transport barriers upon melting. Conversely for PS, acetic acid penetrated the glassy polymer without inducing chain mobility until the glass transition was reached, above which the observed structural changes were consistent with enhanced segmental mobility which enabled bulk penetration. These results suggest that polymer morphology and thermally activated physical transitions arising from diffusion and polymer–solvent interactions can influence whether autoxidation of plastics is transport-limited or kinetically controlled, providing a framework for aligning reaction conditions with reaction outcomes.

09 BIOMASS FUELS↗
DOE OSTI2024

Release dynamics of nanodiamonds created by laser-driven shock-compression of polyethylene terephthalate

Laser-driven dynamic compression experiments of plastic materials have found surprisingly fast formation of nanodiamonds (ND) via X-ray probing. This mechanism is relevant for planetary models, but could also open efficient synthesis routes for tailored NDs. We investigate the release mechanics of compressed NDs by molecular dynamics simulation of the isotropic expansion of finite size diamond from different P-T states. Analysing the structural integrity along different release paths via molecular dynamic simulations, we found substantial disintegration rates upon shock release, increasing with the on-Hugnoiot shock temperature. We also find that recrystallization can occur after the expansion and hence during the release, depending on subsequent cooling mechanisms. Our study suggests higher ND recovery rates from off-Hugoniot states, e.g., via double-shocks, due to faster cooling. Laser-driven shock compression experiments of polyethylene terephthalate (PET) samples with in situ X-ray probing at the simulated conditions found diamond signal that persists up to 11 ns after breakout. In the diffraction pattern, we observed peak shifts, which we attribute to thermal expansion of the NDs and thus a total release of pressure, which indicates the stability of the released NDs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Selective electrified polyethylene upcycling by pore-modulated pyrolysis

Plastic waste is a increasing problem, accumulating in landfills and the environment. Pyrolysis is a promising and industrially relevant approach for transforming plastic waste into value-added chemicals. However, the selectivity and yield of traditional plastic pyrolysis are poor, with products featuring broad molar mass distributions. Here we report a highly selective, energy-efficient and catalyst-free pyrolysis method that can upcycle plastic into value-added chemicals via pore-modulated pyrolysis. Using a Joule-heated carbon column, we demonstrate the pivotal role of the reactor’s graded porous structure in decreasing the polydispersity of the reaction intermediates, enabling high product selectivity and yield. The decreasing pore size of the reactor modulates the mass transport in an apparent gating effect—preventing high-molar-mass species from exiting the reactor before sufficient pyrolysis has occurred. Using polyethylene as a model reactant, we demonstrate a high yield of 65.9 ± 5.2% and up to 80.8% selectivity toward value-added aviation fuel precursor (C8–C18 hydrocarbons) without the use of any catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Influence of functional additives, fillers, and pigments on thermal and catalytic pyrolysis of polyethylene for waste plastic upcycling

Pyrolysis offers a relatively green and economical method to convert waste plastics into valuable chemicals and fuels without the need for harmful solvents, toxic chemicals, or costly high-pressure reactors. Despite its popularity among chemical upcycling technologies, industrial adoption suffers from feedstock heterogeneity, low-quality products, and catalyst deactivation. Most plastics in our daily lives are formulated with functional additives, fillers, and colorants. These additives remaining in end-of-life waste streams increase feedstock heterogeneity, creating a challenging issue in recycling plastics. Still, the potential impacts of additives on the chemical upcycling of plastics have been poorly understood. In this study, polyethylene compounded with a range of widely used additives (antioxidants, stabilizers, pigments, fillers, slip agents, and flame retardants) was subjected to both thermal pyrolysis and catalytic pyrolysis in different catalyst-to-feedstock contact modes. It showed that many inorganic additives, such as talc, kaolin, CaCO 3 , TiO 2 , carbon black, and zinc stearate, facilitated polymer decomposition during pyrolysis, increasing light hydrocarbons while also promoting aromatic and carbon residue formation. Conversely, antioxidants and stabilizers inhibited depolymerization, favoring heavier hydrocarbons. During catalytic pyrolysis with HZSM-5 zeolite, additives strongly enhanced aromatic and catalytic coke formation, especially when there was direct contact between plastics and catalysts. Although certain additives seem beneficial in the short term by promoting polymer cracking and improving the selectivity of aromatics, the transport of the additives and their degradation products and increased carbon coking can contaminate products, deactivate or modify catalysts, and foul reactors. These findings address a critical knowledge gap in effectively converting waste plastics via a greener route.

42 ENGINEERING↗
DOE OSTI2025

Microscopic insights into the solvation of polyethylene glycol chains in water: A machine learning potential approach

Polyethylene glycol (PEG) is a structurally simple, nontoxic, and water-soluble polymer widely utilized in medical and pharmaceutical applications. Notably, when a PEG chain is immersed in water, the surrounding water molecules play a key role in driving conformational changes of this macromolecule. In this study, we explore the solvation behavior of PEG under mechanical strain using molecular dynamics simulations, with an interatomic potential obtained from machine learning. Our focus is on the transition from the favored coil-like conformation to an extended one under external force. Through analyses of radial distribution functions, hydrogen bonding, and solvation dynamics, we uncover how mechanical stretching influences the local hydration environment. Furthermore, we disentangle the enthalpic and entropic contributions to the conformational stability of PEG in water. Surprisingly, our neural network potential model identifies dewetting of PEG C-atoms, and not water H-bonding with PEG O-atoms, as the main enthalpic driving force for the coiling of PEG in water.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Discovery and adaptation of microbes that degrade oxidized low-density polyethylene films

There is a growing interest in developing a methodology for effectively cleaving carbon–carbon (C–C) bonds in polymer backbones through bioconversion processes that utilize microorganisms and their enzymes. This upsurge of interest is driven by the goal of achieving a circular economy. Polyolefin post-consumer plastics are a substantial source of carbon, but the recycling potential is severely limited. Upcycling routes are needed for converting polyolefin post-consumer plastics into value-added products while concurrently mitigating adverse environmental effects. These materials contain carbon-based chemicals that can, in principle, serve as the feedstock for microbial metabolism. Some microbes have been reported to grow on polyolefin plastics, but the rate of biodegradation is insufficient for industrial processes. In this study, low-density polyethylene (LDPE) films were subjected to two mild ozone-based oxidation treatments, which facilitated biodegradation. The degree of oxidation was determined by Fourier transform infrared spectroscopy via analysis of the carbonyl index (1,710/1,460 cm −1 ), which ranged from 0.3 to 2.0, and also via analysis of the carboxylic acid content. Following oxidation of the films, studies were conducted to investigate the ability of a panel of polyvinyl alcohol-degrading microbes to degrade the oxidized films. A defined minimal medium was used to cultivate and assess microbial growth on the oxidized films. Following 45 days of cultivation, the most effective strains were further cultivated up to three additional generations on the oxidized film substrates to improve their ability to degrade the oxidized LDPE films. After these enrichments, we identified a strain from the third generation of Pseudomonas sp. Rh926 that exhibited significant cell growth and reduced the oxidized LDPE film mass by 25% in 30 days, demonstrating an enhanced capacity for degrading the oxidized LDPE films.

Adaptation↗
DOE OSTI2024

Modulated Thermomechanical Analysis of Compression-Molded High-Density Polyethylene

Thermomechanical analysis (TMA) experiments conducted on high-density polyethylene (HDPE) show both reversible and irreversible dimensional changes. To further explore these reversible and irreversible processes, modulated thermomechanical analysis (MTMA) was used. Before reliable data on compression-molded HDPE was collected, a parameter optimization was performed to obtain a suitable MTMA method. Once a suitable method was obtained, several MTMA experiments were conducted on compression-molded HDPE. This work highlights the steps taken during the MTMA parameter optimization and the results obtained from MTMA experiments conducted on pristine compression-molded HDPE samples.

36 MATERIALS SCIENCE↗
DOE OSTI2024

From Plastic Waste to Fuel: Pyrolysis and Gasification of Polyethylene for Hydrogen Production

Thermochemical conversion processes offer promising solutions to address the plastic pollution crisis by transforming plastic waste into valuable products, notably hydrogen. In this study, thermal pyrolysis and steam gasification of polyethylene (PE), the most abundantly produced plastic waste, are investigated in a drop tube reactor system. Various process parameters, namely temperature, residence time, and feedstock composition, are evaluated to establish their correlations with reaction performance. Coal refuse, obtained from discarded thickener underflow in coal processing, is introduced as a co-feedstock for gasification to enhance PE handling and examine synergistic effects on product distribution, particularly H2 yield and syngas quality. Furthermore, the potential of low-cost, environmentally friendly catalysts (i.e., iron oxides, coal ash) for tar reforming is explored.

Natesakhawat, Sittichai↗
DOE OSTI2024

TEX-Cl: Integral Experiment Execution of Thermal/Epithermal eXperiments using Highly Enriched Uranium with Polyethylene and Chloride Absorbers

This report documents the experimental configurations and measurements performed for IER-499, TEX with chlorine (TEX-Cl). TEX-Cl is a variant of the TEX-HEU campaign and utilizes highly enriched uranium fuel, high-density polyethylene (HDPE) moderators and reflectors, and interstitial NaCl salt absorbers. These experiments probe the chlorine (from the sodium chloride) absorption cross section in the thermal and intermediate neutron energy regimes, with a small portion in the fast neutron energy regime. Three configurations were selected by maximizing the sensitivity in k eff to the needs of Y-12 for their electrorefining operations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Implementation of Detailed Polyethylene Pyrolysis Kinetics into CFD Simulations using Machine Learning

Municipal solid waste (MSW) and waste plastics have received significant attention due to the issues of waste generation and storage, as well as their potential as an energy resource. High-density polyethylene (HDPE) makes up a large portion of plastic waste and has been the subject of several conversion studies. However, the mechanisms associated with converting HDPE through pyrolysis and gasification are extensive and complex making them difficult to implement into high-fidelity computational fluid dynamic (CFD) simulations. For this project, a primary pyrolysis mechanism containing 42 unique species and 737 heterogeneous reactions was used to generate kinetic data over a range of operating conditions. A machine learning (ML) model was developed to replicate the results of the detailed pyrolysis mechanism while significantly increasing the computational efficiency. A deep operator network (DeepONet) architecture was adopted to train the model using time steps relevant to CFD simulations. The ML used physics-based loss functions to ensure mass conservation. The ML model has been deployed in simple MFiX CFD simulations, single particle, and an experimental drop tube reactor, and has shown promising performance compared to the original scheme.

Houston, Ross↗
DOE OSTI2024

Development of a machine learning model for polyethylene pyrolysis using a detailed reaction mechanism

Waste plastics have recently received significant attention as the issue of waste generation continues to increase. Thermal conversion processes, such as pyrolysis and gasification, are attractive potential technologies for utilizing waste plastics and reducing overall waste generation. Efficient utilization of plastics requires a detailed understanding of the conversion process such as pyrolysis and gasification. However, a mechanistic understanding of these processes lead to large and complex kinetic schemes that are not suited for large-scale and long-time simulation methods. Currently, most modeling approaches for pyrolysis and gasification rely on globally lumped, simplified kinetic schemes that provide results that are classified by their product type and not individual species, which limit the level of fidelity achieved via modeling. A machine learning (ML) model has been developed for the primary reactions of high-density polyethylene (HDPE) in an attempt to increase computational efficiency while still maintaining a high level of detail and accuracy. The ML model is trained on a detailed reaction mechanism containing 42 total species and 737 chemical reactions. A DeepONet branch and trunk architecture was adopted to train the model using time-steps relevant to computational fluid dynamics simulations. The ML used physics-informed loss functions to ensure mass conservation. The surrogate model has been deployed in simple MFiX CFD simulations, single particle and an experimental drop tube reactor, and has shown promising performance compared to the original scheme.

Houston, Ross↗
DOE OSTI2024

Synthesizing Highly Crystalline Graphite Powder from Bulk Polyethylene Waste for Lithium-Ion Battery Anodes

Upcycling plastic waste into graphite can potentially be used, in conjunction with other methods, to manage existing waste materials and diversify graphite supply chains. However, synthesizing large quantities of crystalline graphite powder from plastic waste, particularly polyethylene (PE), remains a challenge because PE decomposes into light gases during thermal processing, and simple methods do not exist at any appreciable size scale to address this challenge. In this work, a method is developed for air processing bulk forms of PE waste to create a stable carbon char that does not readily decompose during high-temperature processing. This method employs solid additives in the form of salts, which are combined with the PE melt during air processing to increase the effective surface area of the melt and improve the oxygen-driven chemistry that stabilizes the PE for high-temperature processing. After removing the solid salt additives from the PE-derived char, it is converted into a highly crystalline bulk graphite powder using a Fe-based low-temperature (<1500 °C) catalytic process. The PE-derived graphite powder showed excellent electrochemical performance as an anode material for lithium-ion batteries (LIBs) with a capacity of up to 302 mAh/g at 0.5 discharge/charge cycles per hour (0.5 C) and capacity retention of 100% after 415 cycles.

Huynh, Ngoc Tien↗