Search NASA⌕ Search

SEARCH · Search NASA

Results for “Polymer solutions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Porous cobalt spheres for high temperature gradient magnetically assisted fluidized beds

Porous metallic cobalt spheres have been prepared as high temperature capable media for employment in gradient magnetically assisted fluidization and filtration technologies. Cobalt impregnated alginate beads are first formed by extrusion of an aqueous suspension of Co3O4 into a Co(II) chloride solution. The organic polymer is thermally decomposed yielding cobalt oxide spheres, followed by reduction to the metallic state, and densification. Cobalt beads have been produced with porosities ranging between 10 and 50%, depending upon sintering conditions. The product media have been characterized by scanning electron microscopy (SEM), nitrogen adsorption porosimetry, and vibrating sample magnetometry. c2003 Elsevier Science Ltd. All rights reserved.

NASA Discipline Life Support Systems↗
NASA NTRSDate not supplied

Characterization of Microbe Resistant Coatings for Use in the ISS Water System

The ISS is a highly controlled environment; however, there are still microbes on it that astronauts bring from their own microbiome. Once within the ISS water treatment system, these microbes not only pose a health risk for astronauts, but they can form biofilms, causing material degradation and system failure. Due to their protective structure, biofilms are notoriously resistant to disinfectants and antibiotics. One proposed solution is applying polymer coatings to the metal parts of the water system to prevent biofilms from forming. Two types of polyampholyte polymers with previously demonstrated nonfouling properties were sent to the ISS in 2021 to test their viability for preventing microbial adhesion in space. However, the only microbial assays performed were microscopy. To enhance this ongoing research project, I developed procedures for culturing, applying, and quantifying Ralstonia pickettii on these polymers. R. pickettii was chosen because it is one of the most prevalent microbes found in the ISS water treatment system. Optical density data was recorded to obtain a growth curve demonstrating a doubling time between 2.83 and 4.88 hours in 30°C, not shaken conditions. Optical density was also correlated to colony forming units in a plating experiment. Another result was design (and pilot testing) of a surface colonization experiment. These results provided vital knowledge about R. pickettii, which will be used for a 2023 payload of antimicrobial polymer coatings on stainless steel, and improved methods for biofilm analysis upon its return to evaluate the efficacy of the coatings.

microbiology↗
NASA NTRS1998

Polymerization on the rocks: theoretical introduction

It is difficult if not impossible to synthesize long polymers of amino acids, nucleotides, etc., in homogeneous aqueous solution. We suggest that long polymers were synthesized on the surface of minerals in a prebiotic process analogous to solid-phase synthesis. Provided that the affinity of a mineral for an oligomer increases with the length of the oligomer, adsorption must become essentially irreversible for sufficiently long oligomers. Irreversibly adsorbed oligomers may be elongated indefinitely by repeated cycles in which the mineral with its adsorbed oligomers is first incubated with activated monomers and then washed free of deactivated monomer and side-products. We discuss in some detail the formation of oligomers of negatively-charged amino acids such as glutamic acid on anion-exchange minerals such as hydroxylapatite or illite. We show that the average length of adsorbed oligomers at steady state, n, depends on the balance between the rate of chain elongation and the rate of hydrolysis, and we derive a very approximate formula for n.

NASA Discipline Exobiology↗
NASA NTRS1997

Process for Preparing a Tough, Soluble, Aromatic, Thermoplastic Copolyimide

A process for preparing a tough, soluble, aromatic, thermoplastic copolyimide is provided. The process comprises the steps of (a) providing 4.4'-oxydiphthalic anhydride to 3,4,3',4'-biphenyltetracarboxylic dianhydride at a mole ratio ranging from about 25 mole percent to 75 mole percent to 75 mole percent to about 25 mole percent; (b) adding 3,4'-oxydianiline to form a mixture; (c) adding a polar aprotic or polar protic solvent to the mixture to form a solution having a percentage of solids capable of maintaining polymer solubility; (d) stirring the solution to allow it to react; (e) adding an azeotropic solvent to the solution and heating to remove water; (f) cooling the solution of step (e) to room temperature and recovering the tough, soluble, aromatic, thermoplastic copolyimide.

Bryant, Robert G.↗
NASA NTRS1973

In situ polymerization of monomers for polyphenylquinoxaline/graphite

Methods currently used to prepare fiber reinforced, high temperature resistant polyphenylquinoxaline (PPQ) composites employ extremely viscous, low solids content solutions of high molecular weight PPQ polymers. An improved approach, described in this report, consists of impregnating the fiber with a solution of the appropriate monomers instead of a solution of previously synthesized high molecular weight polymer. Polymerization of the monomers occurs in situ on the fiber during the solvent removal and curing stages. The in situ polymerization approach greatly simplifies the fabrication of PPQ graphite fiber composites. The use of low viscosity monomeric type solutions facilitates fiber wetting, permits a high solids content, and eliminates the need for prior polymer synthesis.

Serafini, T. T.↗
NASA NTRS1974

In situ polymerization of monomers for polyphenylquinoxaline/graphite fiber composites

Methods currently used to prepare fiber reinforced, high temperature resistant polyphenylquinoxaline (PPQ) composites employ extremely viscous, low solids content solutions of high molecular weight PPQ polymers. An improved approach, described in this report, consists of impregnating the fiber with a solution of the appropriate monomers instead of a solution of previously synthesized high molecular weight polymer. Polymerization of the monomers occurs in situ on the fiber during the solvent removal and curing stages. The in situ polymerization approach greatly simplifies the fabrication of PPQ graphite fiber composites. The use of low viscosity monomeric type solutions facilitates fiber wetting, permits a high solids content, and eliminates the need for prior polymer synthesis.

Serafini, T. T.↗
NASA NTRS2016

Spontaneous Oligomerization of Nucleotide Alternatives in Aqueous Solutions

On early Earth, a primitive polymer that could spontaneously form from likely available precursors may have preceded both RNA and DNA as the first genetic material. Here, we report that heated aqueous solutions containing 5-hydroxymethyluracil (HMU) result in oligomers of uracil, heated solutions containing 5-hydroxymethylcytosine (HMC) result in oligomers of cytosine, and heated solutions containing both HMU and HMC result in mixed oligomers of uracil and cytosine. Oligomerization of hydroxymethylated pyrimidines, which may have been abundant on the primitive Earth, might have been important in the development of simple informational polymers.

Liquid chromatography↗
NASA NTRS1999

Flight Validation of Atomic Oxygen Resistant Resistant Polymers

Because of its high reactivity, atomic oxygen causes surface erosion on polymeric materials. although the reaction efficiency depends on the chemical structure of the polymer. We have found an organotin compound, bis(triphenyltin) oxide (BTO), which has an unusually high solubility in solutions of a number of commercial high performance polymers. Films of these polymers containing BTO showed a substantial reduction in erosion by atomic oxygen when compared with films of the pure material. Analysis has shown that in the presence of atomic oxygen, erosion of the exposed surfaces of the BTO-containing films leaves a residual protective tin oxide coating . Since the additive is uniformly distributed throughout the polymeric material, any break or puncture in the protective coating is "healed" by the material below. Samples were exposed to the environment of the low earth orbit (LEO) on two Space Shuttle flights, STS-46, in June of 1992, and STS-51 in September of 1993. The analysis of these samples has been reported previously. For both flights, the samples were small (1.3 cm and 1.9 cm respectively) thus limiting the scope of analysis. In the research under this cooperative agreement, films of a polyetherimide, were exposed to the LEO environment on Space Shuttle flight STS-85 in August of 1997 as part of the Evaluation of Space Environment and Effects on Materials (ESEM) experiment. The polyetherimide chosen is available commercially as Ultem, registered to the General Electric Company. Films of pure Ultem, Ultem with 10% BTO by mass, and Ultem with 20% BTO by mass were exposed in the ram direction for 40 hours during STS-85. Ultem has a Tg of 215 deg C and is soluble in common chlorinated solvents. Granules of the polymer were dried at 120 deg C, but otherwise were used as received. Films were cast on a glass plate from a solution of the polymer in a 60/40 (w/w) mixture of chloroform and 1,1,2,2-tetrachloroethane. The plate was placed in a dust-free box for at least 24 hours to allow much of the solvent to evaporate, and then was moved to a vacuum oven and slowly heated from 20 to 220 deg C over a period of two weeks to completely remove all solvent. Each exposed sample was 7.6 cm long and 2.2 cm wide and about 0.025 mm thick. The structures of Ultem and bis(triphenyltin) oxide are shown.

Kiefer, Richard L.↗
NASA NTRS2002

Development of a New Membrane Casting Apparatus for Studying Macrovoid Defects in Low-G

A new membrane-casting apparatus is developed for studying macrovoid defects in polymeric membranes made by the wet- and dry-casting process in low-gravity. Macrovoids are large (10-50 micron), open cavities interspersed among the smaller pores in the substructure under the gelled skin surface layer of the cast membrane. Although their occurrence is considered endemic to the wet- and dry-casting process since they can lead to compaction or skin rupture in the membrane process, recent studies suggest several useful applications such as transdermal and osmotic drug delivery systems, miniature bioreactors, etc. However, lack of knowledge about the macrovoid formation mechanism is an obstacle to further development of applications using them. An on-going debate is the role of the surface-tension-driven solutocapillary convection during macrovoid formation. The rapid growth of macrovoids within 1-5 seconds and the high polymer concentration in and near macrovoids make it difficult to explain the mechanism of macrovoid growth by diffusion alone, which is the widely accepted hypothesis proposed by Reuvers et al. The hypothesis advanced by our research group can explain this rapid growth via a mechanism that involves diffusion from the casting solution in the meta-stable region to the macrovoid enhanced by solutocapillary convection induced by the steep nonsolvent concentration gradient in the vicinity of the macrovoid. Since macrovoid growth is hypothesized to be the interplay of a solutocapillary-induced driving force counteracted by viscous drag and buoyancy, eliminate the latter provides a means for testing this hypothesis. Moreover, free convection mass transfer in the nonsolvent immersion bath used to cause phase-separation in membrane casting complicates developing a model for both the wet-casting process and macrovoid growth. The low-g environment minimizes gravitationally induced free convection thereby permitting a tractable solution to the ternary diffusion equations that characterize membrane formation. NASA's Parabolic Flight Research Aircraft provides a small window of low-g (approximately 25 s) that can be used to study macrovoid development in both wet- and dry-cast membranes if an appropriate casting apparatus is used. This casting apparatus should be able to cast the membrane in both low- and high-g in a manner so that essential one-dimensional mass transfer conditions are achieved to insure lateral uniformity in the membrane. The apparatus used in previous research on membrane casting in low-gravity was operated with the plunger driven mechanism. The spring-loaded plunger pushes the bottom block containing the polymer casting solution well directly under the absorbent chamber located in the upper stationary block. However, membranes made via this casting apparatus often displayed lateral nonuniformities that precluded obtaining quantitative information on the macrovoid growth process. Thus, it was necessary to determine the reason for these structural irregularities observed in the low-g casting apparatus. Both experimental as well as computer simulation studies of the low-g casting apparatus established that the impulsive action of the plunger caused the undesired structural nonuniformities. The simulation results showed that the width-to-depth aspect ratio of the shallow well that contains the casting solution in this apparatus was not an important factor in minimizing this problem. Even for a 40:1 (width : depth) aspect ratio, any convection induced by the horizontal motion of the interface of the casting solution will be damped out within 6.25x10(exp 4) seconds. However, the experimental studies revealed that the impulsive motion of the plunger caused a 'sloshing' of the casting solution that had to be eliminated. Therefore, the plungerdriven mechanism was changed to a cam-driven mechanism that did not cause any impulsive motion of the casting solution. Other refinements to this new membrane-casting apparatus include provision for removing the membranes from the casting wells in a less destructive manner. This was accomplished by using a slit geometry for the casting well that permitted disassembly for removal of the cast membrane. The materials used in the construction of this casting apparatus were chosen to insure wetting at the side walls and to maintain precise control of the thickness of the polymer solution in the casting well. An additional provision in this new casting apparatus is the ability to carry out both wet- as well as dry-casting. As such, this apparatus permitted the first studies of the wet-casting of polymeric membranes in low-g. Both wet- and dry-casting experiments on NASA's KC-135 research aircraft employing this new membrane-casting apparatus are scheduled in July 2002. The morphology of the resulting membranes will be characterized using an environmental scanning electron microscope (ESEM). The results of these low-g studies will be reported later.

Lee, Hanyong↗
NASA NTRS2008

Electroconductive PET/SWNT Films by Solution Casting

The market for electrically conductive polymers is rapidly growing, and an emerging pathway for attaining these materials is via polymer-carbon nanotube (CNT) nanocomposites, because of the superior properties of CNTs. Due to their excellent electrical properties and anisotropic magnetic susceptibility, we expect CNTs could be easily aligned to maximize their effectiveness in imparting electrical conductivity to the polymer matrix. Single-walled carbon nanotubes (SWNT) were dispersed in a polyethylene terephthalate (PET) matrix by solution blending then cast onto a glass substrate to create thin, flexible films. Various SWNT loading concentrations were implemented (0.5, 1.0, and 3.0 wt.%) to study the effect of additive density. The processing method was repeated to produce films in the presence of magnetic fields (3 and 9.4 Tesla). The SWNTs showed a high susceptibility to the magnetic field and were effectively aligned in the PET matrix. The alignment was characterized with Raman spectroscopy. Impedance spectroscopy was utilized to study the electrical behavior of the films. Concentration and dispersion seemed to play very important roles in improving electrical conductivity, while alignment played a secondary and less significant role. The most interesting result proved to be the effect of a magnetic field during processing. It appears that a magnetic field may improve dispersion of unmodified SWNTs, which seems to be more important than alignment. It was concluded that SWNTs offer a good option as conductive, nucleating filler for electroconductive polymer applications, and the utilization of a magnetic field may prove to be a novel method for CNT dispersion that could lead to improved nanocomposite materials.

Steinert, Brian W.↗
NASA NTRS1998

Nuclear Instruments and Methods in Physics Research: Microstructural Characterization of Semi-Interpenetrating Polymer Networks by Positron Lifetime Spectroscopy - Section B

Thermoset and thermoplastic polyimides have complementary physical/mechanical properties. Whereas thermoset polyimides are brittle and generally easier to process, thermoplastic polyimides are tough but harder to process. It is expected that a combination of these two types of polyimides may help produce polymers more suitable for aerospace applications. Semi-Interpenetrating Polymer Networks (S-IPNs) of thermoset LaRC(Trademark)-RP46 and thermoplastic LARC(Trademark)-IA polyimides were prepared in weight percent ratios ranging from 100:0 to 0: 100. Positron lifetime measurements were made in these samples to correlate their free volume features with physical/mechanical properties. As expected, positronium atoms are not formed in these samples. The second life time component has been used to infer the positron trap dimensions. The "free volume" goes through a minimum at about 50:50 ratio, suggesting that S-IPN samples are not merely solid solutions of the two polymers. These data and related structural properties of the S-IPN samples have been discussed in this paper.

Singh, Jag J.↗
NASA NTRS1996

Microstructural Characterization of Semi-Interpenetrating Polymer Networks by Positron Lifetime Spectroscopy

Thermoset and thermoplastic polyimides have complementary physical and mechanical properties. Whereas thermoset polyimides are brittle and generally easier to process, thermoplastic polyimides are tough but harder to process. A combination of these two types of polyimides may help produce polymers more suitable for aerospace applications. Semi-Interpenetrating Polymer Networks (S-IPN) of thermoset LaRC(TM)-RP46 and thermoplastic LaRC(TM)-IA polyimides were prepared in weight percent ratios ranging from 100:0 to 0:100. Positron lifetime measurements were made in these samples to correlate their free volume features with physical and mechanical properties. As expected, positronium atoms are not formed in these samples. The second lifetime component has been used to infer the positron trap dimensions. The 'free volume' goes through a minimum at a ratio of about 50:50, and this suggests that S-IPN samples are not merely solid solutions of the two polymers. These data and related structural properties of the S-IPN samples are discussed.

Singh, Jag J.↗
NASA NTRS1981

Terrestrial evolution of polymerization of amino acids - Heat to ATP

Sets of amino acids containing sufficient trifunctional monomer are thermally polymerized at temperatures such as 65 deg; the amino acids order themselves. Various polymers have diverse catalytic activities. The polymers aggregate, in aqueous solution, to cell-like structures having those activities plus emergent properties, e.g. proliferatability. Polyamino acids containing sufficient lysine catalyze conversion of free amino acids, by ATP, to small peptides and a high molecular weight fraction. The lysine-rich proteinoid is active in solution, within suspensions of cell-like particles, or in other particles composed of lysine-rich proteinoid and homopolyribonucleotide. Selectivities are observed. An archaic polyamino acid prelude to coded protein synthesis is indicated.

Fox, S. W.↗
NASA NTRS2011

Effect of Water on the Thermo-Mechanical Behavior of Carbon Cloth Phenolic

The results of thermo-mechanical experiments, which were conducted previously by one of the authors, are reviewed. The strain in the direction normal to the fabric plane was measured as a function of temperature for a variety of initial moisture contents and heating rates. In this paper, the general features of the thermo-mechanical response are discussed and the effect of heating rate and initial moisture content are highlighted. The mechanical interaction between the phenolic polymer and water trapped within its free volumes as the polymer is heated to high temperatures is discussed. An equation for the internal stresses which are generated within the polymer due to trapped water is obtained from the total stress expression for a binary mixture of polymer and water. Numerical solutions for moisture diffusion in the thermo-mechanical experiments were performed and the results of these solutions are presented. The results of the moisture diffusion solutions help to explain the effects of heating rate and moisture content on the strain behavior normal to the fabric plane.

Sullivan, Roy M.↗
NASA NTRS2008

Sensing/actuating materials made from carbon nanotube polymer composites and methods for making same

An electroactive sensing or actuating material comprises a composite made from a polymer with polarizable moieties and an effective amount of carbon nanotubes incorporated in the polymer for a predetermined electromechanical operation of the composite when such composite is affected by an external stimulus. In another embodiment, the composite comprises a third component of micro-sized to nano-sized particles of an electroactive ceramic that is also incorporated in the polymer matrix. The method for making the three-phase composite comprises either incorporating the carbon nanotubes in the polymer matrix before incorporation of the particles of ceramic or mixing the carbon nanotubes and particles of ceramic together in a solution before incorporation in the polymer matrix.

Ounaies, Zoubeida↗
NASA NTRS2009

Method of Making an Electroactive Sensing/Actuating Material for Carbon Nanotube Polymer Composite

An electroactive sensing or actuating material comprises a composite made from a polymer with polarizable moieties and an effective amount of carbon nanotubes incorporated in the polymer for a predetermined electromechanical operation of the composite when such composite is affected by an external stimulus. In another embodiment, the composite comprises a, third component of micro -sized to nano-sized particles of an electroactive ceramic that is also incorporated in the polymer matrix. The method for making the three-phase composite comprises either incorporating the carbon nanotubes in the polymer matrix before incorporation of the particles of ceramic or mixing the carbon nanotubes and particles of ceramic together in a solution before incorporation in the polymer matrix.

Ounaies, Zoubeida↗
NASA NTRS1981

Rheological behavior of progressively shear-thickening solutions

The rheological behavior of the recently developed polymer FM-9 in Jet A fuel and JP 8 fuel is reported. In aqueous solution, FM 9 is found to exhibit strong time-dependent shear thickening behavior. Induction time necessary for the onset of thickening is found to depend on shear rate, solvent, concentration, and molecular weight. Altering the nature of the solvent results in effects similar to those obtained by changing the concentration or molecular weight. A critical shear rate is derived, and is inversely proportional to the zero shear rate viscosity of the solution for the temperature and concentrations observed. The onset of shear thickening behavior appears to be related to the onset of viscoelastic response, and thus the time scale follows reduced variable behavior.

Peng, S. T. J.↗
NASA NTRS1976

Stripper for silicone polymers

Potassium hydroxide in ethyl alcohol solution can strip away coatings, adhesives, and encapsulants without damaging substrates.

Williams, B. B.↗