Search NASA⌕ Search

SEARCH · Search NASA

Results for “Power at sea”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Comparative Analysis of Pendulum and Flywheel Power Take-Off Mechanisms for Wave Energy Conversion

Here, this study compares three power-take-off (PTO) mechanisms for wave energy converters—a flywheel -type pitch resonator and two pendulum variants (normal and inverted)—all designed to fit within a fixed envelope. Performance is assessed via linear frequency-domain models and bi-conjugate impedance matching under a representative sea state. The inverted-pendulum PTO achieves 27.9% of the incident wave energy, versus 16.5% for the normal pendulum and 4.2% for the flywheel—that is, 6.6 × and 3.9 × improvements, respectively. These gains arise because pendulum-based systems generate higher torque for a given buoy motion and maintain impedance matching across a wider frequency band. Parametric studies of mass, pendulum arm length, spring stiffness, generator friction, and motor constant quantify the impact of key design choices on power output. By locating the pendulum pivot near the buoy's center of gravity and positioning the center of rotation below the COG, surge–pitch coupling is improved and energy transfer is further boosted.

Keow, Alicia Li Jen [Sandia National Laboratories ↗
DOE OSTI2020

Characteristics and Variability of the Nearshore Wave Resource on the U.S. West Coast

Characterizing the nearshore wave resource at a regional scale poses a great challenge because high-quality wave data are required. This paper presents a detailed analysis of nearshore wave climate and resource characterization on the U.S. West Coast based on a 32-year, regional wave hindcast. Resource characterization closely followed the International Electrotechnical Commission standards. The wave hindcast data were generated from an unstructured-grid SWAN model with approximately 300 m grid resolution in the nearshore region. Statistics of six IEC wave resource parameters at the 50 m water depth were calculated for four sub-regions along the coast, including Washington, Oregon, and Northern and Southern California. Results indicate that the Washington and Oregon coast has a similar nearshore wave resource. The wave resource in Southern California is significantly less than that of the Washington and Oregon coast. Alongshore and cross-shore variabilities of wave power were assessed. Temporal variability, at seasonal, inter-annual, and decadal scales were analyzed. Overall, strong seasonal variation is observed; high wave energy occurs in the winter months and calm seas in the summer. Finally, extreme environmental conditions, i.e., the 100-year extreme environmental contours, for different locations along the West Coast were investigated.

wave resource characterization, nearshore, west co↗
DOE OSTI2022

CFD Simulation of Floating Body Motion with Mooring Dynamics: Coupling MoorDyn with OpenFOAM

It is increasingly popular to use Computational Fluid Dynamics (CFD) models to study floating structures subjected to ocean waves, especially when it comes to applications of floating offshore wind turbines and Wave Energy Converters (WECs). Mooring dynamics are currently lacking in most of these applications. This paper presents a coupled simulation study of moored floating body motion by coupling two open-source libraries: a finite volume CFD toolbox, OpenFOAM, and a lumped-mass mooring model, MoorDyn. The instantaneous floating body position and velocity are passed from the body motion solver in the CFD model to the mooring model to calculate the fairlead kinematics. The mooring reaction forces, which are calculated by MoorDyn after updating the mooring system states, are then returned to the body motion solver to update the floating body motion. Both mesh deformation and overset mesh methods are used as the mesh motion solver in the CFD model to account for the floating body motion. The coupled model was validated against experimental measurements for a floating box moored with four catenary lines under the action of regular waves, which came from a preliminary test campaign for WECs. Apart from the lumped-mass mooring model, the present work also coupled a quasi-static mooring model and a finite element model with the floating body motion solver in OpenFOAM. The mooring line tensions predicted by these models were compared. The coupled model equipped with three mooring line codes may be further used to carry out survivability studies of FOWTs and WECs subject to severe sea states.

floating body↗
DOE OSTI2023

Using Dark Fiber and Distributed Acoustic Sensing to Characterize a Geothermal System in the Imperial Valley, Southern California

The Imperial Valley, CA, is a tectonically active transtensional basin located south of the Salton Sea; the area hosts numerous geothermal fields, including significant hidden hydrothermal resources without surface manifestations. Development of inexpensive, rugged, and highly sensitive exploration techniques for undiscovered geothermal systems is critical for accelerating geothermal power deployment as well as unlocking a low-carbon energy future. We present a case study utilizing distributed acoustic sensing (DAS) and ambient noise interferometry for geothermal reservoir imaging, utilizing unlit fiber-optic telecommunication infrastructure (dark fiber). The study exploits two days of passive DAS data acquired in early November 2020 over a ~28-km section of fiber from Calipatria, CA to Imperial, CA. We apply ambient noise interferometry to retrieve coherent signals from DAS records and develop a bin stacking technique to attenuate the effects from persistent localized noise sources and to enhance retrieval of coherent surface waves. As a result, we are able to obtain high-resolution two-dimensional (2D) S wave velocity ($V_s$) structure to 3 km depth, based on joint inversion of both the fundamental and higher overtones. We observe a previously unmapped high $V_s$ and low $V_p$/$V_s$ ratio feature beneath the Brawley geothermal system, which we interpret to be a zone of hydrothermal mineralization and lower porosity. This interpretation is consistent with a host of other measurements including surface heat flow, gravity anomalies, and available borehole wireline data. These results demonstrate the potential utility of DAS deployed on dark fiber for geothermal system exploration and characterization in the appropriate geological settings.

Vp/Vs imaging↗
DOE OSTI2024

Predictive model using artificial neural network to design phase change material-based ocean thermal energy harvesting systems for powering uncrewed underwater vehicles

Uncrewed Underwater Vehicles (UUVs) are a major beneficiary of the phase change material (PCM)-based ocean thermal energy harvesting technology for their mission needs. However, this technology relies on different parameters and energy conversion steps that could be critical to the general energy generation efficiency. Sea trials showed that the design performed lower than their laboratory design specifications. This underperformance results from different factors, mainly the UUV’s trajectory, travel time, underwater ocean currents, temperature fluctuations, and biofouling on the heat exchanger due to long term underwater operations. Therefore, there exists a need to continuously monitor the ambient energy harvesting system and predict system performance, for mission planning purposes. Two major parameters influencing the energy harvesting system include the final pressure inside the hydraulic energy storage vessel or accumulator, and the electrical load value. Here, this work focuses on the hydraulic to electric energy conversion system. Therefore, a combination of numerical model and experimental testing is used to develop a predictive model using artificial neural network using MATLAB. After validation with experimental testing, 1000 data samples obtained from the numerical model are used to train the ANN. Compared to the experimental results, the developed ANN model can predict in less than a second the designed benchtop system’s total efficiency with less than 15 percent maximum error range. This predictive model development represents a cost-effective way for optimization and a computational energy efficient mode aboard UUVs for mission planning for deployed UUVs using PCM-based ocean thermal energy harvesting technology.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Wave Measurements taken NW of Culebra Is., PR, 2023

Wave and sea surface temperature measurements collected by a Sofar Spotter buoy in 2023. The buoy was deployed on July 27, 2023 at 11:30 UTC northwest of Culebra Island, Puerto Rico, (18.3878 N, 65.3899 W) and recovered on Nov 5, 2023 at 12:45 UTC. Data are saved here in netCDF format, organized by month, and include directional wave statistics, GPS, and SST measurements at 30-minute intervals. Figures produced from these data are provided here as well. They include timeseries of wave height/period/direction and SST, GPS location, wave roses, and directional spectra. Additionally, raw CSV files from the Spotter's memory card can also be found below. NetCDF files can be read in python using the netCDF4 or Xarray packages, or through MATLAB using the "ncread()" command.

16 TIDAL AND WAVE POWER↗
DOE OSTI2022

Marine renewable energy for Arctic observations

Arctic observations are becoming increasingly valuable as researchers investigate climate change and its associated concerns, such as decreasing sea ice and increasing ship traffic. Networks of sensors with frequent sampling capabilities are needed to run forecast models, improve navigation, and inform climate research. Sampling frequency and deployment duration are currently constrained by battery power limitations. In-situ power generation using marine renewable energy sources such as waves and currents can be used to circumvent this constraint. Wave and current resources vary spatially and temporally in the Arctic, with some locations and seasons being better suited for marine renewable energy power generation. Locations and seasons with small resources may still be able to use marine renewable energy because of the low power requirements of the instruments. In this study, we describe the wave and current resources in the Arctic, outline the electricity generation developments that are needed to utilize the resources, and suggest use cases. Wave and current energy converters developed to power observations in the Arctic could also be used to power observations at lower latitudes. Marine renewable energy has the potential to decrease dependence on batteries and improve data collection capabilities in the Arctic; however, this would require the development of new low power technologies that can operate in extreme Arctic environments.

16 TIDAL AND WAVE POWER↗
DOE OSTI2023

MASK4 Test Campaign for Sandia WaveBot Device

This data and report details the findings from a wave tank test focused on production of useful work of a wave energy converter (WEC) device. The experimental system and test were specifically designed to validate models for power transmission throughout the WEC system. Additionally, the validity of co-design informed changes to the power take-off (PTO) were assessed and shown to provide the expected improvements in system performance. These data describe the "MASK4" wave tank test of the Sandia WaveBot device. The WaveBot device has been tested a number of times in different permutations at the US Navy's Maneuvering and Sea Keeping (MASK) basin. Each test in this series is referred to as MASK1, MASK2, etc. The WaveBot device was first tested in one degree of freedom (heave) in 2016. This MASK1 test focused primarily on system identification and modeling. After MASK1, major modifications were performed to improve the overall real-time control and measurement system, improve the heave drive train, and add surge and pitch degrees of freedom. The second set of testing, which was broken up in to two stages: MASK2A and MASK2B, focused on bench testing and closed-loop control performance as well as nonlinear modeling. MASK3 then focused on multi-input, multi-output modeling and control for maximization of electrical power. The attached report presents the results from MASK4, which focuses on detailed modeling of the power conversion chain and validation co-design principles by way of the introduction of a magnetic spring. The test log, report, and data from the MASK4 test of the WaveBot augmented with a tunable magnetic spring. Processing codes can be found at the Github link below.

16 TIDAL AND WAVE POWER↗
DOE OSTI2020

LandRAY Final Report

The overarching Project objective is to demonstrate the feasibility of using an innovative Power Take-Off (PTO) Module, to be used in the Columbia Power Technologies, Inc. (C·Power) utility-scale wave energy converter (WEC). The PTO Module uniquely combines a large-diameter, direct-drive, rotary permanent magnet generator; a patent-pending rail-bearing system; and a corrosion-resistant fiber-reinforced-plastic structure. The rail bearing system allows for: • A flexible non-rigid and low-cost generator frame as compared to conventional machines. • A reduction of air gap and consequently lower cost electromagnetic design • Ability to reduce costs by increasing diameter to much larger dimensions, while maintaining the small air gap. • A direct drive electro-mechanical solution that is the fastest and most precise approach for responding to the dynamic variability of forces from wave energy. The land-based test of the PTO Module (DDP1) will provide an important risk reduction phase, to demonstrate the reliability and feasibility of a large-diameter, small air-gap generator that is capable of delivering high efficiency, fault-tolerance and relatively simple "at-sea" maintenance capabilities – qualities that are essential for cost-effective wave energy devices. This is the first known test of such a system.

16 TIDAL AND WAVE POWER↗
DOE OSTI2023

Influence on Structural Loading of a Wave Energy Converter by Controlling Variable-Geometry Components and the Power Take-Off

Oceans are harsh environments and can impose significant loads on deployed structures. A wave energy converter (WEC) should be designed to maximize the energy absorbed while ensuring the operating wave condition does not exceed the failure limits of the device itself. Therefore, the loads endured by the support structure are a design constraint for the system. Furthermore, the WEC should be adaptable to different sea states. Herethis work uses a WEC-Sim model of a variable-geometry oscillating wave energy converter (VGOSWEC) mounted on a support structure simulated under different wave scenarios. A VGOSWEC resembles a paddle pitching about a fixed hinge perpendicular to the incoming wave fronts. The geometry of the VGOSWEC is varied by opening a series of controllable flaps on the pitching paddle when the structure experiences threshold loads. It is hypothesized that opening the flaps should result in load shedding at the base of the support structure by reducing the moments about the hinge axis. This work compares the hydrodynamic coefficients, natural periods, and response amplitude operators from completely closed to completely open configurations of the controllable flaps. This work shows that the completely open configuration can reduce the pitch and surge loads on the base of the support structure by as much as 80%. Increased loads at the structure’s natural period can be mitigated by an axial power take-off damping acting as an additional design parameter to control the loads at the WEC’s support structure.

16 TIDAL AND WAVE POWER↗
DOE OSTI2022

Megadrought: A Series of Unfortunate La Niña Events?

Megadroughts are multidecadal periods of aridity more persistent than most droughts during the instrumental period. Paleoclimate evidence suggests that megadroughts occur in many parts of the world, including North America, Central America, western Europe, eastern Asia, and northern Africa. It remains unclear to what extent such megadroughts require external forcing or whether they can arise from internal climate variability alone. A novel statistical–dynamical approach is used to evaluate the possibility that such events arise solely as a function of interannual tropical sea surface temperature (SST) variations. A statistical emulator of tropical SST variations is constructed by using an empirical moving-blocks bootstrap approach that randomly samples multiyear sequences of the observational SST record. This approach preserves the power spectrum, seasonal cycle, and spatial pattern of El Niño-Southern Oscillation (ENSO) but removes longer timescale fluctuations embedded in the observational record. These resampled SST anomalies are then used to force an atmospheric model (the Community Atmosphere Model Version 5). As megadroughts emerge in this run, they should, therefore, be solely a consequence of La Niña sequences combined with internal atmospheric variability and persistence driven by soil moisture storage and other land-surface processes. We indeed find that megadroughts in this simulation have an amplitude-duration rate that is generally indistinguishable from the rate documented in paleoclimate records of the western United States. Our findings support the idea that megadroughts may occur randomly when the unforced climate system evolves freely over a sufficiently long period of time, implying that an unforced unusual but statistically plausible series of La Niña events may be sufficient to generate megadrought.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Midfidelity Model Verification for a Point-Absorbing Wave Energy Converter with Linear Power Take-Off

In the preliminary design stage of a wave energy converter (WEC), fast and reliable simulation tools are required. High-fidelity numerical models are usually employed to study the wave-structure interaction, yet the computational cost is demanding. Instead, mid-fidelity models provide simulations in the order of real time. In this study, Uppsala University WEC operates in a relatively mild sea state and is modeled using WEC-Sim. The model is verified based on OpenFOAM simulations. To analyze the ability of mid-fidelity model to capture the WEC dynamics, the system is investigated separately in 1, 2 and 3 DoF. The contribution of viscous phenomena is examined. Moreover, linear and weakly non-linear solutions provided by WEC-Sim are studied. The results obtained indicate that the viscous effects in heave and surge motion can be neglected but not for the pitch. The weakly non-linear WEC-Sim solution successfully agrees with the CFD, whereas the linear solution could drive to misleading results.

CFD↗
DOE OSTI2021

Midfidelity Model Verification for a Point-Absorbing Wave Energy Converter with Linear Power Takeoff: Preprint

In the preliminary design stage of a wave energy converter (WEC), fast and reliable simulation tools are required. High-fidelity numerical models are usually employed to study the wave-structure interaction, yet the computational cost is demanding. Instead, mid-fidelity models provide simulations in the order of real time. In this study, Uppsala University WEC operates in a relatively mild sea state and is modeled using WEC-Sim. The model is verified based on OpenFOAM simulations. To analyze the ability of mid-fidelity model to capture the WEC dynamics, the system is investigated separately in 1, 2 and 3 DoF. The contribution of viscous phenomena is examined. Moreover, linear and weakly non-linear solutions provided by WEC-Sim are studied. The results obtained indicate that the viscous effects in heave and surge motion can be neglected but not for the pitch. The weakly non-linear WEC-Sim solution successfully agrees with the CFD, whereas the linear solution could drive to misleading results.

CFD↗
DOE OSTI2022

Midfidelity model verification for a point-absorbing wave energy converter with linear power take-off

In the preliminary design stage of a wave energy converter (WEC), researchers need fast and reliable simulation tools. High-fidelity numerical models are usually employed to study the wave-structure interaction, but the computational cost is demanding. As an alternative, midfidelity models can provide simulations in the order of real time. In this study, we operate Uppsala University’s WEC in a relatively mild sea state and model it using WEC-Sim. The model is verified based on OpenFOAM simulations. To analyze the ability of the midfidelity model to capture WEC dynamics, we investigate the system separately with 1, 2, and 3 degrees of freedom. We examine the contribution of viscous phenomena, and study both linear and weakly nonlinear solutions provided by WEC-Sim. Our results indicate that the viscous effects can be neglected in heave and surge motion, but not for pitch. We also find that the weakly nonlinear WEC-Sim solution successfully agrees with the computational fluid dynamics, whereas the linear solution could suggest misleading results.

16 TIDAL AND WAVE POWER↗
DOE OSTI2022

2.2.5.401 - Ocean Observing Prize

The Powering the Blue Economy: Ocean Observing Prize is a $2.4M contest that challenges innovators to develop solutions that integrate marine renewable energy with ocean observation platforms to revolutionize our ability to monitor, manage, and understand the ocean. Competitors are challenged to design, build, and test novel, wave-powered, self-charging autonomous underwater vehicle (AUV) systems that could be suitable for a 6-month deployment in the Atlantic Ocean to monitor hurricane formation. Through engagement with the end user ocean observing community, the team identified challenges in a lack of data on storm intensity, endangering coastal communities. This challenge could be addressed by collecting data before, during, and after a hurricane develops and strengthens at sea. Amassing this data, however, requires an ocean observing system that can be deployed at sea for long periods, waiting for approaching storms. To help solve this problem, competitors are working to integrate wave energy capture with AUV systems to collect this data, helping to better protect coastal communities from oncoming storms. Solutions developed through this prize aim to enable long-term collection of data before, during, and after a hurricane that will help better forecast storm intensity. The prize mechanism provides an environment to accelerate technology development for innovators and helps to improve awareness of marine energy and its ability to provide power to blue economy applications.

coastal communities↗
DOE OSTI2020

Major Revisions in Arthropod Phylogeny Through Improved Supermatrix, With Support for Two Possible Waves of Land Invasion by Chelicerates

Deep phylogeny involving arthropod lineages is difficult to recover because the erosion of phylogenetic signals over time leads to unreliable multiple sequence alignment (MSA) and subsequent phylogenetic reconstruction. One way to alleviate the problem is to assemble a large number of gene sequences to compensate for the weakness in each individual gene. Such an approach has led to many robustly supported but contradictory phylogenies. A close examination shows that the supermatrix approach often suffers from two shortcomings. The first is that MSA is rarely checked for reliability and, as will be illustrated, can be poor. The second is that, to alleviate the problem of homoplasy at the third codon position of protein-coding genes due to convergent evolution of nucleotide frequencies, phylogeneticists may remove or degenerate the third codon position but may do it improperly and introduce new biases. We performed extensive reanalysis of one of such “big data” sets to highlight these two problems, and demonstrated the power and benefits of correcting or alleviating these problems. Our results support a new group with Xiphosura and Arachnopulmonata (Tetrapulmonata + Scorpiones) as sister taxa. This favors a new hypothesis in which the ancestor of Xiphosura and the extinct Eurypterida (sea scorpions, of which many later forms lived in brackish or freshwater) returned to the sea after the initial chelicerate invasion of land. Our phylogeny is supported even with the original data but processed with a new “principled” codon degeneration. We also show that removing the 1673 codon sites with both AGN and UCN codons (encoding serine) in our alignment can partially reconcile discrepancies between nucleotide-based and AA-based tree, partly because two sequences, one with AGN and the other with UCN, would be identical at the amino acid level but quite different at the nucleotide level.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

TEAMER Technical Support for Optimal Control of an Oscillating Surge Wave Energy Converter (CRADA Final Report)

This project will focus on running experiments that evaluate the benefits of using model predictive control (MPC) to optimize power absorbed by a laboratory-scale oscillating surge wave energy converter (OSWEC). MPC is a promising technique to optimize wave energy converter (WEC) behavior while applying system constraints that can help promote structural integrity and device survivability, but there are few studies that experimentally test this control scheme on WECs. Therefore, the Participant is proposing a series of tests that will assess the benefits of MPC experimentally in response to a variety of sea states. For these tests, the Participant will provide the OSWEC device and Data Acquisition (DAQ) system, and request support from the Contractor to use and operate the wave tank for experiments.

16 TIDAL AND WAVE POWER↗