SEARCH · Search NASA

Results for “Prandtl numbers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Reynolds shear stress and heat flux calculations in a fully developed turbulent duct flow

The use of a modified form of the Van Driest mixing length for a fully developed turbulent channel flow leads to mean velocity and Reynolds stress distributions that are in close agreement with data obtained either from experiments or direct numerical simulations. The calculations are then extended to a nonisothermal flow by assuming a constant turbulent Prandtl number, the value of which depends on the molecular Prandtl number. Calculated distributions of mean temperature and lateral heat flux are in reasonable agreement with the simulations. The extension of the calculations to higher Reynolds numbers provides some idea of the Reynolds number required for scaling on wall variables to apply in the inner region of the flow.

Antonia, R. A.↗

NASA NTRS1993

Stability and instability of thermocapillary convection in models of the float-zone crystal-growth process

This project was concerned with the determination of conditions of guaranteed stability and instability for thermocapillary convection in a model of the float-zone crystal-growth process. This model, referred to as the half-zone, was studied extensively, both experimentally and theoretically. Our own earlier research determined, using energy-stability theory, sufficient conditions for stability to axisymmetric disturbances. Nearly all results computed were for the case of a liquid with Prandtl Number Pr = 1. Attempts to compute cases for higher Prandtl numbers to allow comparison with the experimental results of other researchers were unsuccessful, but indicated that the condition guaranteeing stability against axisymmetric disturbances would be a value of the Marangoni number (Ma), significantly higher than that at which oscillatory convection was observed experimentally. Thus, additional results were needed to round out the stability picture for this model problem. The research performed under this grant consisted of the following: (1) computation of energy-stability limits for non-axisymmetric disturbances; (2) computation of linear-stability limits for axisymmetric and non-axisymmetric disturbances; (3) numerical simulation of the basic state for half- and full-zones with a deformable free surface; and (4) incorporation of radiation heat transfer into a model energy-stability problem. Each of these is summarized briefly below.

Neitzel, G. P.↗

NASA NTRS1984

Asymmetric instabilities in buoyancy-driven flow in a tall vertical annulus

Linear stability of the one-dimensional flow between infinite vertical coaxial cylinders induced by heating the inner cylinder is considered for various ratios (kappa) of the inner radius to the outer radius, and for Prandtl numbers (P) appropriate to air and water. For air with P = 0.71 the least stable disturbance is nonaxisymmetric for kappa less than 0.44 and is axisymmetric for kappa greater than 0.44, and in either case the instability is due to the action of the shear forces. For P = 3.5, the situation is similar, except that the asymmetric shear mode is superseded by an axisymmetric instability driven by buoyancy forces for kappa = 0.03-0.16. Wave speeds, wavenumbers, and critical Grashof numbers for these cases and for the case of zero Prandtl number are given.

Mcfadden, G. B.↗

NASA NTRS1982

Computer program for solving laminar, transitional, or turbulent compressible boundary-layer equations for two-dimensional and axisymmetric flow

A numerical algorithm and computer program are presented for solving the laminar, transitional, or turbulent two dimensional or axisymmetric compressible boundary-layer equations for perfect-gas flows. The governing equations are solved by an iterative three-point implicit finite-difference procedure. The software, program VGBLP, is a modification of the approach presented in NASA TR R-368 and NASA TM X-2458, respectively. The major modifications are: (1) replacement of the fourth-order Runge-Kutta integration technique with a finite-difference procedure for numerically solving the equations required to initiate the parabolic marching procedure; (2) introduction of the Blottner variable-grid scheme; (3) implementation of an iteration scheme allowing the coupled system of equations to be converged to a specified accuracy level; and (4) inclusion of an iteration scheme for variable-entropy calculations. These modifications to the approach presented in NASA TR R-368 and NASA TM X-2458 yield a software package with high computational efficiency and flexibility. Turbulence-closure options include either two-layer eddy-viscosity or mixing-length models. Eddy conductivity is modeled as a function of eddy viscosity through a static turbulent Prandtl number formulation. Several options are provided for specifying the static turbulent Prandtl number. The transitional boundary layer is treated through a streamwise intermittency function which modifies the turbulence-closure model. This model is based on the probability distribution of turbulent spots and ranges from zero to unity for laminar and turbulent flow, respectively. Several test cases are presented as guides for potential users of the software.

Harris, J. E.↗

NASA NTRS1962

Measurement of Local Heat Transfer Coefficients for Flow of Hydrogen and Helium in a Smooth Tube at High Surface to Fluid Bulk Temperature Ratios

Local values of heat transfer coefficients have been measured experimentally for helium and hydrogen gas flowing through an electrically heated inconel tube. The experiment was conducted primarily to determine the effect on the heat transfer coefficient of a large density change, radially, in the heat transfer fluid. This large density change was accomplished with relatively high surface temperatures as compared to fluid bulk temperatures or more commonly referred to as high surface to fluid bulk temperature ratio. The large temperature ratio was achieved by precooling the gas with liquid nitrogen. Data were measured for local values of surface to fluid bulk temperature ratios up to 4.5, Reynolds numbers in the turbulent flow region, surface temperatures up to 2300° R, heat flux up to 1,600,000 Btu/(hr)(sq ft) and length to diameter ratio of 250. A comparison of this data with the conventional heat transfer· correlation equation (Dittus-Boelter eq.) is shown on a curve of Nusselt number divided by Prandtl number versus the Reynolds number. The gas properties were evaluated at the film temperature and the Reynolds number was modified by evaluating the velocity term at the fluid bulk temperature and the density at the film temperature.

Weiland, Walter F.↗

NASA NTRS1981

Finite-analytic numerical solution of heat transfer in two-dimensional cavity flow

Heat transfer in cavity flow is numerically analyzed by a new numerical method called the finite-analytic method. The basic idea of the finite-analytic method is the incorporation of local analytic solutions in the numerical solutions of linear or nonlinear partial differential equations. In the present investigation, the local analytic solutions for temperature, stream function, and vorticity distributions are derived. When the local analytic solution is evaluated at a given nodal point, it gives an algebraic relationship between a nodal value in a subregion and its neighboring nodal points. A system of algebraic equations is solved to provide the numerical solution of the problem. The finite-analytic method is used to solve heat transfer in the cavity flow at high Reynolds number (1000) for Prandtl numbers of 0.1, 1, and 10.

Chen, C.-J.↗

NASA NTRS1983

Viscous thermocapillary convection at high Marangoni number

A liquid, contained in a quarter plane, undergoes steady motion due to thermocapillary forcing on its upper boundary, a free surface separating the liquid from a passive gas. The rigid vertical sidewall has a strip whose temperature is elevated compared with the liquid at infinity. A boudnary-layer analysis is performed that is valid for large Marangoni numbers M and Prandtl numbers P. It is found that the Nusselt number N for the horizontal heat transport satisfies N proportional to min (M to the 1 2/7/power, M to the 1 1/5/power, M to the 1 1/10/power) Generalizations are discussed.

Cowley, S. J.↗

NASA NTRS1975

Wall Cooling Effects on Hypersonic Transitional/Turbulent Boundary Layers at High Reynolds Numbers

A 4 degree wedge was used to produce a thick turbulent boundary layer with an edge Mach number of 11. By using a two-dimensional model, the boundary layer was nearly free from upstream history effects associated with nozzle wall turbulent boundary layers. Heat-transfer distributions were used to define regions of laminar, transitional, and turbulent flow at several values of T(sub w)/T(sub t) for an edge unit Reynolds number of 0.47 x lot per cm. Pitot and total temperature profiles and skin-friction measurements were obtained at selected stations along the model. Turbulence parameters (mixing length/sigma and epsilon) were derived from the fully turbulent profiles and used to more completely define the "low Reynolds number" effect. Turbulent Prandtl number distributions are also presented.

Watson, Ralph D.↗

NASA NTRS2002

An Evaluation of Parameters Influencing Jet Mixing Using the WIND Navier-stokes Code

The WIND code, a Reynolds-averaged Navier-Stokes solver used for a variety of aerospace flow simulations, was investigated for a Mach 2 nozzle at a series of nozzle stagnation temperatures. Comparisons of WIND calculations are made to experimental measurements of axial velocity, Mach number, and stagnation temperature along the jet centerline. The primary objective was to investigate the capabilities of the two-equation turbulence models available in WIND, version 4.0, for the analysis of heated supersonic nozzle flows. The models examined were the Menter Shear Stress Transport (SST) model and the Chien k-epsilon model, with and without the compressibility correction due to Sarkar. It was observed that all of the turbulence models investigated produced solutions that did not agree well with the experimental measurements. The effects of freestream Mach number and turbulent Prandtl number specifications were also investigated.

Dembowski, Mary Ann↗

DOE OSTI2021

Studying the effect of the upper internal structure design on thermal stratification in sodium fast reactors

Thermal stratification and mixing in large reactor pools can pose significant issues with regard to operation and safety of nuclear plants. While significant work has been done in this area on light water reactors it is more critical for sodium reactors and there is far less data with regard to low Prandtl number fluids. Here this paper focuses on the effect of the upper internal structure on the formation of thermal stratification in a scaled sodium fast reactor upper plenum. Six different upper internal structure configurations were tested to observe the effect on thermal stratification. The degree of stratification was quantified using the stratification number. Each configuration was tested from low to high flow rates at a temperature difference of 50 and 100 °C. Over this broad array of testing, it was observed that higher flow rates, more porosity in the upper internal structure design, and a smaller temperature difference yielded a lower degree of stratification. This information can be used to aid in the design of the upper internal structure in a sodium fast reactor. Furthermore, this high resolved temperature data can be used to verify models under prototypic low Prandtl numbers.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1972

The turbulent boundary layer on a porous plate: An experimental study of the heat transfer behavior with adverse pressure gradients

An experimental investigation of the heat transfer behavior of the near equilibrium transpired turbulent boundary layer with adverse pressure gradient has been carried out. Stanton numbers were measured by an energy balance on electrically heated plates that form the bottom wall of the wind tunnel. Two adverse pressure gradients were studied. Two types of transpiration boundary conditions were investigated. The concept of an equilibrium thermal boundary layer was introduced. It was found that Stanton number as a function of enthalpy thickness Reynolds number is essentially unaffected by adverse pressure gradient with no transpiration. Shear stress, heat flux, and turbulent Prandtl number profiles were computed from mean temperature and velocity profiles. It was concluded that the turbulent Prandtl number is greater than unity in near the wall and decreases continuously to approximately 0.5 at the free stream.

Blackwell, B. F.↗

DOE OSTI2022

Magnetic fields in the formation of the first stars – II. Results

ABSTRACT Beginning with cosmological initial conditions at z = 100, we simulate the effects of magnetic fields on the formation of Population III stars and compare our results with the predictions of Paper I. We use gadget-2 to follow the evolution of the system while the field is weak. We introduce a new method for treating kinematic fields by tracking the evolution of the deformation tensor. The growth rate in this stage of the simulation is lower than expected for diffuse astrophysical plasmas, which have a very low resistivity (high magnetic Prandtl number); we attribute this to the large numerical resistivity in simulations, corresponding to a magnetic Prandtl number of order unity. When the magnetic field begins to be dynamically significant in the core of the minihalo at z = 27, we map it on to a uniform grid and follow the evolution in an adaptive mesh refinement, MHD simulation in orion2. The non-linear evolution of the field in the orion2 simulation violates flux-freezing and is consistent with the theory proposed by Xu & Lazarian. The fields approach equipartition with kinetic energy at densities ∼1010–1012 cm−3. When the same calculation is carried out in orion2 with no magnetic fields, several protostars form, ranging in mass from ∼1 to 30 M⊙; with magnetic fields, only a single ∼30 M⊙ protostar forms by the end of the simulation. Magnetic fields thus suppress the formation of low-mass Pop III stars, yielding a top-heavy Pop III initial mass function and contributing to the absence of observed Pop III stars.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS1955

Analysis and calculation by integral methods of laminar compressible boundary-layer with heat transfer and with and without pressure gradient

A survey of integral methods in laminar-boundary-layer analysis is first given. A simple and sufficiently accurate method for practical purposes of calculating the properties (including stability) of the laminar compressible boundary layer in an axial pressure gradient with heat transfer at the wall is presented. For flow over a flat plate, the method is applicable for an arbitrarily prescribed distribution of temperature along the surface and for any given constant Prandtl number close to unity. For flow in a pressure gradient, the method is based on a Prandtl number of unity and a uniform wall temperature. A simple and accurate method of determining the separation point in a compressible flow with an adverse pressure gradient over a surface at a given uniform wall temperature is developed. The analysis is based on an extension of the Karman-Pohlhausen method to the momentum and the thermal energy equations in conjunction with fourth- and especially higher degree velocity and stagnation-enthalpy profiles.

Morduchow, Morris↗

NASA NTRS1949

Further Experiments on the Flow and Heat Transfer in a Heated Turbulent Air Jet

Measurements have been made of the mean total-head and temperature fields in a round turbulent jet with various initial temperatures. The results show that the jet spreads more rapidly as its density becomes lower than that of the receiving medium, even when the difference is not sufficiently great to cause measurable deviations from the constant-density, dimensionless, dynamic-pressure profile function. Rough analytical considerations have given the same relative spread. The effective "turbulent Prandtl number" for a section of the fully developed jet was found to be equal to the true (laminar) Prandtl number within the accuracy of measurement. (author)

FLOW - JETS↗

NASA NTRS1950

Further Experiments on the Flow and Heat Transfer in a Heated Turbulent Air Jet

Measurements have been made of the mean-total-head and mean-temperature fields in a round turbulent jet with various initial temperatures. The results show that the jet spreads more rapidly as its density becomes lower than that of the receiving medium, even when the difference is not sufficiently great to cause dynamic-pressure function. Rough analytical considerations have given the same relative spread. The effective "turbulent Prandtl number" for a section of the fully developed jet was found to be equal to the true (laminar) Prandtl number within the accuracy measurement.

Corrsin, Stanley↗

NASA NTRSDate not supplied

Simulation and Modeling of Hypersonic Turbulent Boundary Layers Subject to Favorable Pressure Gradients due to Streamline Curvature

Direct numerical simulations (DNS) of favorable-pressure-gradient turbulent boundary layers are presented for a nominal freestream Mach number of 5, with the objective of assessing the limitations of the currently available Reynolds-averaged Navier-Stokes (RANS) models.The wall geometry and flow conditions of the DNS are representative of the experimental data for a Mach 4.9 turbulent boundary layer that was tested on a two-dimensional planar convexwall model in the high-speed blow-down wind tunnel located at the National Aerothermochemistry Laboratory at Texas A&M University. The favorable pressure gradient is induced bythe streamwise surface curvature. The DNS results will be compared with experimental measurements and RANS computations for the same flow conditions and wall geometry. The DNS datasets will also be analyzed to provide an improved physical understanding of hypersonic boundary-layer turbulence subject to mechanical nonequilibrium, including the validity of Morkovin’s hypothesis and the various available compressibility transformations, as well as to obtain turbulence statistics that are relevant to RANS modeling, including the distribution ofeddy viscosity, the budgets of turbulent kinetic energy and Reynolds stresses, and the velocity-temperature correlations. The RANS predictions will be obtained by using both the commonly used one- and two-equation models that assume a constant turbulent Prandtl number and an algebraic, variable Prandtl number model for the turbulent energy flux.

turbulent boundary layers↗

DOE OSTI2025

Thermovelocimetric characterization of liquid metal convection in a rotating slender cylinder

Rotating turbulent convection occurs ubiquitously in natural convective systems encompassing planetary cores, oceans and atmospheres, as well as in many industrial applications. While the global heat and mass transfer of water-like rotating Rayleigh–Bénard convection is well-documented, the dynamics in low-Prandtl-number liquid metals remain less understood. In this study, we experimentally investigate rotating Rayleigh-Bénard convection in liquid gallium (Prandtl number Pr ≈ 0.027) within a slender cylinder (diameter-to-height aspect ratio Γ = D/H =1/2) using novel thermovelocimetric diagnostic techniques that integrate simultaneous multi-point thermometry and ultrasonic Doppler velocity measurements. Our results reveal the formation of a stable, global-scale azimuthal wavenumber m = 2 quadrupolar vortex at low supercriticality. We propose that enhanced wall modes facilitated by the slender cylinder geometry interact with the bulk flow to create these large-scale axialized vortices. Furthermore, our findings imply a distinct scaling behavior for the wall-mode precession frequency in liquid metals, extending previous results obtained for moderate-Pr fluids. In conclusion, this provides new insights into wall-bulk coupling mechanisms of low-Pr rotating convective turbulence.

Magnetohydrodynamics↗

NASA NTRS1976

Laminar free convection from a vertical cone with uniform surface heat flux

The laminar free convection flow from a right circular cone with prescribed uniform wall flux condition is studied. The governing boundary-layer equations are analyzed by the technique of similarity transformation. Numerical solutions to the transformed equations are given for Prandtl numbers 0.72, 1, 2, 4, 6, 8, 10, and 100. Expressions for both wall temperature distribution and wall skin friction distribution at Prandtl number tending to infinity are also presented.

Lin, F. N.↗