Search NASA⌕ Search

SEARCH · Search NASA

Results for “Process variable”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

SMS/GOES cell and battery data analysis report

The nickel-cadmium battery design developed for the Synchronous Meteorological Satellite (SMS) and Geostationary Operational Environmental Satellite (GOES) provided background and guidelines for future development, manufacture, and application of spacecraft batteries. SMS/GOES battery design, development, qualification testing, acceptance testing, and life testing/mission performance characteristics were evaluated for correlation with battery cell manufacturing process variables.

Armantrout, J. D.↗

Rheology of composite solid propellants during motor casting

In a study conducted to evaluate flow parameters of uncured solid composite propellants during motor casting, two motors (1.8M-lb grain wt) were cast with a PBAN propellant exhibiting good flow characteristics in a 260-in. dia solid rocket motor. Attention is given to the effects of propellant compositional and processing variables on apparent viscosity as they pertain to rheological behavior and grain defect formation during casting. It is noted that optimized flow behavior is impaired with solid propellant loading. Non-Newtonian pseudoplastic flow is observed, which is dependent upon applied shear stress and the age of the uncured propellant.

Rogers, C. J.↗

Phase 1 of the automated array assembly task of the low cost silicon solar array project

The results of a study of process variables and solar cell variables are presented. Interactions between variables and their effects upon control ranges of the variables are identified. The results of a cost analysis for manufacturing solar cells are discussed. The cost analysis includes a sensitivity analysis of a number of cost factors.

Pryor, R. A.↗

Survey of ion plating sources

Based on the type of evaporation source, gaseous media and mode of transport, the following is discussed: resistance, electron beam, sputtering, reactive and ion beam evaporation. Ionization efficiencies and ion energies in the glow discharge determine the percentage of atoms which are ionized under typical ion plating conditions. The plating flux consists of a small number of energetic ions and a large number of energetic neutrals. The energy distribution ranges from thermal energies up to a maximum energy of the discharge. The various reaction mechanisms which contribute to the exceptionally strong adherence - formation of a graded sustrate/coating interface are not fully understood, however the controlling factors are evaluated. The influence of process variables on the nucleation and growth characteristics are illustrated in terms of morphological changes which affect the mechanical and tribological properties of the coating.

Spalvins, T.↗

Rheology of composite solid propellants during motor casting

Results of casting studies are reviewed so as to define the viscosity criteria insuring the fabrication of defect-free grains. The rheology of uncured propellants is analyzed showing that a realistic assessment of a propellant's flow properties must include measurement of viscosity as a function of shear stress and time after curing agent. Methods for measuring propellant viscosity are discussed, with particular attention given to the Haake-Rotovisko rotational viscometer. The effects of propellant compositional and processing variables on apparent viscosity are examined, as are results relating rheological behavior to grain defect formation during casting.

Klager, K.↗

Survey of ion plating sources

Ion plating is a plasma deposition technique where ions of the gas and the evaporant have a decisive role in the formation of a coating in terms of adherence, coherence, and morphological growth. The range of materials that can be ion plated is predominantly determined by the selection of the evaporation source. Based on the type of evaporation source, gaseous media and mode of transport, the following will be discussed: resistance, electron beam sputtering, reactive and ion beam evaporation. Ionization efficiencies and ion energies in the glow discharge determine the percentage of atoms which are ionized under typical ion plating conditions. The plating flux consists of a small number of energetic ions and a large number of energetic neutrals. The energy distribution ranges from thermal energies up to a maximum energy of the discharge. The various reaction mechanisms which contribute to the exceptionally strong adherence - formation of a graded substrate/coating interface are not fully understood, however the controlling factors are evaluated. The influence of process variables on the nucleation and growth characteristics are illustrated in terms of morphological changes which affect the mechanical and tribological properties of the coating.

Spalvins, T.↗

Analysis of long-term ionizing radiation effects in bipolar transistors

The ionizing radiation effects of electrons on bipolar transistors have been analyzed using the data base from the Voyager project. The data were subjected to statistical analysis, leading to a quantitative characterization of the product and to data on confidence limits which will be useful for circuit design purposes. These newly-developed methods may form the basis for a radiation hardness assurance system. In addition, an attempt was made to identify the causes of the large variations in the sensitivity observed on different product lines. This included a limited construction analysis and a determination of significant design and processes variables, as well as suggested remedies for improving the tolerance of the devices to radiation.

Stanley, A. G.↗

Graphite composites with advanced resin matrices

The effect of processing variables on the flammability and mechanical properties for state-of-the-art and advanced resin matrices for graphite composites were studied. Resin matrices which were evaluated included state-of-the-art epoxy, phenolic-novolac, phenolic-xylok, two types of bismaleimides, benzyl, polyethersulfone, and poly(p-phenylene sulfone). Comparable flammability and thermochemical data on graphite-reinforced laminates prepared with these resin matrices are presented, and the relationship of some of these properties to the anaerobic char yield of the resins is described.

Kourtides, D. A.↗

A cause of the non-solderability of ceramic capacitor terminations

The results of an analysis into the cause of the non-solderability of multiple defective part lots from two capacitor manufacturers are described. This analysis consisted of visual, scanning electron microscopic, surface, and metalographic examinations and analyses. The results indicated that non-solderability results from areas of excess porosity in the termination which are caused by segregation of ink constituents during manufacturing. This segregation can be minimized by proper monitoring and control of process variables; where excess porosity does occur, solderability can be improved by proper precleaning of parts.

Cozzolino, M. J.↗

Development of rapidly solidified oxidation resistant alloys

The development of iron-base alloys that contain low concentrations of expensive and/or strategic metals, but that are very resistant to oxidation at elevated tempratures was investigated. Rapid solidification processing was employed to make alloys that are uniform in composition, that comprise very fine grains 10 microns and that contain a uniform dispersion of very fine ( 0.5 microns) nonmetallic inclusions. Each of these factors contribute to the oxidation behavior of alloys. The compositional and processing variables that yield the optimum oxidation resistance are described.

Yurek, G. J.↗

Studies of metals electroprocessing in molten salts

Fluid flow patterns in molten salt electrolytes were observed in order to determine how mass transport affects the morphology of the metal deposit. Studies conducted on the same metal, both in aqueous electrolytes in which coherent solid electrodeposits are produced, as well as in transparent molten salt electrolytes are described. Process variables such as current density and composition of the electrolyte are adjusted to change the morphology of the electrodeposit and, thus, to permit the study of the nature of electrolyte flow in relation to the quality of the electrodeposit.

Sadoway, D. R.↗

Advanced ceramic coating development for industrial/utility gas turbines

A program was conducted with the objective of developing advanced thermal barrier coating (TBC) systems. Coating application was by plasma spray. Duplex, triplex and graded coatings were tested. Coating systems incorporated both NiCrAly and CoCrAly bond coats. Four ceramic overlays were tested: ZrO2.82O3; CaO.TiO2; 2CaO.SiO2; and MgO.Al2O3. The best overall results were obtained with a CaO.TiO2 coating applied to a NiCrAly bond coat. This coating was less sensitive than the ZrO2.8Y2O3 coating to process variables and part geometry. Testing with fuels contaminated with compounds containing sulfur, phosphorus and alkali metals showed the zirconia coatings were destabilized. The calcium titanate coatings were not affected by these contaminants. However, when fuels were used containing 50 ppm of vanadium and 150 ppm of magnesium, heavy deposits were formed on the test specimens and combustor components that required frequent cleaning of the test rig. During the program Mars engine first-stage turbine blades were coated and installed for an engine cyclic endurance run with the zirconia, calcium titanate, and calcium silicate coatings. Heavy spalling developed with the calcium silicate system. The zirconia and calcium titanate systems survived the full test duration. It was concluded that these two TBC's showed potential for application in gas turbines.

Vogan, J. W.↗

Sensitivity analysis results of the effects of various parameters on composite design

Sensitivity analysis results are presented to assess the effects of a multitude of important parameters on fiber composite design and structural response. These results were obtained by using optimum design procedures in conjunction with sensitivity analyses. Sensitivity analyses were performed to assess the effects on composite optimum design and structural response of parameters such fiber transverse and shear properties, in situ matrix elastic and strength properties, correlation coefficients used in composite micromechanics and in combined strength predictions, processing variables, and perturbations of loading conditions. The results show that matrix properties, fiber volume ratio and small perturbations of the loading conditions have significant effects on certain composite structural responses. The remaining parameters have negligible effect.

Chamis, C. C.↗

Ultrasonics and Optics Would Control Shot Size

Feedback system assures production of silicon shot of uniform size. Breakup of silicon stream into drops is controlled, in part, by varying frequency of vibrations imparted to stream by ultrasonic transducer. Drop size monitored by photodetector. Control method particularly advantageous in that constant size is maintained even while other process variables are changed deliberately or inadvertently. Applicable to materials other than silicon.

Morrison, A. D.↗

Silicon Foils Growth by Interface-controlled Crystallization

During interface controlled crystallization (ICC) the chance to accelerate the removal of crystallization heat is the basis for high pulling rates of about 100 mm/min. The forced heat flow from the extended crystallization front to a cooling ramp is controlled by a lubricating melt film which also influences the crystallization behavior by suppressing nucleation centers. The basic principles of this full casting technique are presented and the influences of process parameters on the morphology of prepared silicon foils are demonstrated. Three different types of crystalline structure were found in silicon foils grown to ICC technique: dendritic, coarse granular and monocrystalline with (111) 211 orientation. The criteria for their appearance of process variables are discussed.

Helmreich, D.↗

Processing and flammability parameters of bismaleimide and some other thermally stable resin matrices for composites

The effect of processing variables on the flammability and mechanical properties of state-of-the-art and advanced resin matrices for graphite composites were studied. Resin matrices which were evaluated included state-of-the-art epoxy, phenolic-novolac, phenolic-Xylok, two types of bismaleimides, benzyl, polyethersulfone, and polyphenylsulfone. Comparable flammability and thermochemical data on graphite-reinforced laminates prepared with these resin matrices are presented, and the relationship of some of these properties to the anaerobic char yield of the resins is described.

Kourtides, D. A.↗

Samics on the IBM PC

An updated version of the Solar Array Manufacturing Industry Costing Standards (SAMICS) was presented. This version will run on the IBM PC-XT or compatibles, and embodies user friendly input screens and numerous help options. Use of this microcomputer version will still produce the old main frame direct cost driven analysis, although at some cost in turnaround time. A typical simulation will take about 4 hours. The program allows for unattended report printout. Also available is the IBM PC (or compatibles) version of the Improved Price Estimation Guidelines (IPEG). This program allows rapid analysis of process variables using SAMICS-generated coefficients.

Chamberlain, R.↗

Modeling the filament winding process

A model is presented which can be used to determine the appropriate values of the process variables for filament winding a cylinder. The model provides the cylinder temperature, viscosity, degree of cure, fiber position and fiber tension as functions of position and time during the filament winding and subsequent cure, and the residual stresses and strains within the cylinder during and after the cure. A computer code was developed to obtain quantitative results. Sample results are given which illustrate the information that can be generated with this code.

Calius, E. P.↗