SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Intermediate magnetostatic propagation mode for spin wave in axially magnetized rod containing turning point, including spin wave losses, explaining delay time
Nuclear thermionic space power system using rod control and heat pipes
Nuclear reactor space power system concept using thermionic diodes, heat pipes and rod control, emphasizing neutronic aspects and feasibility
Dynamic mode electromagnetic surface waves on axially magnetized single crystalline YIG and polycrystalline ferrite rods
Development of high temperature polyimide rod seals for use with hydraulic fluids in advanced aircraft
Nuclear reactor control rod assembly with improved driving mechanism
High temperature polyimide actuator rod seals for aircraft hydraulic systems
Time dependence of laser rod focal length, measuring thermal lensing effects
Two types of polyimide seals are developed for hydraulic actuator rod in low pressure second stage of two-stage configuration. Each seal melts test objectives of twenty million cycles of operation at 534 K. Analytical and experimental study results are discussed. Potential applications are given.
Use of segmented rods in operation of quadrupole mass spectrometer
Sensitivity of quadrupole mass spectrometer with segmented rod geometry
Aircraft high temperature polyimide hydraulic actuator rod seals, discussing design and performance tests
A commercial quadrupole residual gas analyzer system has been upgraded for operation at extended cable lengths. Operation inside a vacuum chamber for the standard quadrupole nude head is limited to approximately 2 m from its externally located rf/dc generator because of the detuning of the rf oscillator circuits by the coaxial cable reactance. The advance of long distance remote operation inside a vacuum chamber for distances of 45 and 60 m was made possible without altering the quadrupole's rf/dc generator circuit by employing an rf link to drive the quadrupole rods. Applications of the system have been accomplished for in situ space simulation thermal/vacuum testing of sophisticated payloads.
Tool is inexpensive and gives repeatable results. It is modified commercially-available rod-type weld slag removal gun and is pneumatically operated by regulated compressed air supply.
Advanced high temperature hydraulic system rod sealing requirements can be met by using seals made of nonelastomeric (plastic) materials in applications where elastomers do not have adequate life. Exploratory seal designs were optimized for advanced applications using machinable polyimide materials. These seals demonstrated equivalent flight hour lives of 12,500 at 350 F and 9,875 at 400 F in advanced hydraulic system simulation. Successful operation was also attained under simulated space shuttle applications; 96 reentry thermal cycles and 1,438 hours of vacuum storage. Tests of less expensive molded plastic seals indicated a need for improved materials to provide equivalent performance to the machined seals.
The objective of this program was to determine the peening stress profiles of rod peened aluminum structural alloys versus shot peened material to define the effective depth of the compressed surface layer.
Machined polyimide second-stage rod seals were evaluated to determine their suitability for single-stage applications where full system pressure acts on the upstream side of the seal. The 6.35-cm (2.5-in.) K-section seal was tested in impulse screening tests where peak pressure was increased in 3.448-MPa (500-psi) increments each 20,000 cycles. Seal failure occurred at 37.92 MPa (5,500 psi), indicating a potential for acceptability in a 27.58-MPa (4,000-psi) system. Static pressurization for 600 sec at pressures in excess of 10.34 MPa (1,500 psi) revealed structural inadequacy of the seal cross section to resist fracture and extrusion. Endurance testing showed the seals capable of at least 65,000 1.27-cm (0.5-in.) cycles at 450 K (350 F) without leakage. It was concluded that the second-stage seals were proven to be exceptional in the 1.379-MPa (200-psi) applications for which they were designed, but polyimide material properties are not adequate for use in this design at pressure loading equivalent to that present in single-stage applications.
The radiation of sound through the open end of a cylindrical or conical pipe of any cross section, or through a hole in a plane wall, is analyzed theoretically. The scattering of a sound wave by the end of a rod or slab is also treated. Only the case in which the wavelength is large compared with a typical radial dimension of the opening or of the end is considered. The method of matched asymptotic expansions is employed. Results on end corrections and reflection coefficients previously obtained by Helmholtz (1860), Rayleigh (1945), and Bazer and Karp (1954), using intuitive arguments, are recovered and verified. Agreement is found with the exact results of Levine and Schwinger (1948) and Vainstein (1948), as well as with the small radial-dimension/wavelength results of Lesser and Lewis (1972), in the cases they treated. In addition various new results are obtained.