Search NASA⌕ Search

SEARCH · Search NASA

Results for “Residue”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Distribution Development for Residual Inventory at the New York West Valley Site - 20400

The New York State Energy Research and Development Authority (NYSERDA) is the owner of the Western New York Nuclear Service Center (WNYNSC), a 1,351 ha site located approximately 48 km south of Buffalo, New York. In 1962, Nuclear Fuel Services, Inc. (NFS) entered into Agreements with the Atomic Energy Commission and New York State to construct the first commercial reprocessing plant of nuclear fuel in the United States. NFS, a private company, built and operated the spent fuel reprocessing plant and waste disposal facilities, processing 640 Mg of spent nuclear fuel from 1966 to 1972 under an Atomic Energy Commission license. Nuclear fuel reprocessing operations ended in 1972 and never reopened, leaving behind radioactive and chemical wastes. Operations led to contamination in a number of facilities and locations. Some of that contamination has migrated from waste disposal zones to other layers, formations, and features on and off the WNYNSC. Phase I decommissioning activities are ongoing and involve the removal of a number of areas and structures that have been associated with contamination. The purpose of this work is to outline the approach for characterizing contamination not associated with disposed wastes, contaminated structures, or specific releases. In this work, the term, residual radiological activity, is used to describe environmental contamination that exists subsequent to the completion of Phase I decommissioning activities, that is not associated with disposed wastes, contaminated structures, or specific releases. Contamination from the Site was quantified relative to data that characterize the concentrations of radionuclides that exist in background. Background concentrations are those present in the area but having no influence from Site related activities. The existence of residual radiological activity that is elevated relative to background has the potential to contribute to future risks to human health and the environment. As a consequence, the residual inventory information is used to inform the West Valley Probabilistic Performance Assessment (PPA) model to characterize potential future risks to human health and the environment. The centralized West Valley Data Management System (DMS) was the source of information for the data assembled in this analysis. The DMS is a fairly large compilation consisting of thousands of records from investigation studies, with sample dates ranging from 1990 to present. Samples from monitoring wells, boreholes, geoprobe studies, surface water, surface soils, storm water outfalls, ventilation stack filters, plant and animal tissues, and more are included in the DMS. Results are typically reported in units of activity per unit volume. For the purpose of the analyses presented here, all results were converted into consistent units of pCi per unit volume. Since 1990, data have been collected from various locations across the WNYNSC at different times with varying frequency over the course of several decades. As a consequence, a number of potential issues can arise with respect to the assembly of a dataset that is deemed adequate for the characterization of residual radiological activity. These issues were assessed and resolved to the extent possible through careful consideration of the properties of the distributions. The intent was to use data which characterize the current state of the Site. Radionuclides can be designated to one of several groups depending on their origin. In this work the groups considered were 1) Naturally Occurring Radioactive Material (NORM), 2) fallout, and 3) Other (including power plant, medical research, etc). This grouping is a useful construct with respect to the interpretation of fixed laboratory results. For example, NORM radionuclides that exist within a decay chain should have approximately equivalent distributions of concentrations if they are representative of background conditions. Insights such as these can be used as a check to identify sample results that need to be further investigated or omitted due to issues associated with reported results from fixed laboratory analyses. This type of analysis provided a foundation for the assessment of the adequacy of sample results for use in subsequent components of an assessment. The general process for the assessment of residual radiological contamination at the Site consists of a sequence of several steps. First, for each analyte, several statistical tests were performed to assess the weight of evidence against the null hypothesis that the mean of the distribution of concentrations was equal to zero. If the mean of the distribution of concentrations for a given radionuclide was not found to be greater than zero, then it was removed from consideration as a component of the residual radiological contamination. If there was significant evidence to reject the hypothesis of the mean being equal to zero, the second step was to compare the distribution of the data from the Site to that of the corresponding background. A suite of tests was used to compare the distributions of the site and background data. The results of these tests were collectively used to determine if site data are elevated relative to background. The third step was to develop distributions using a Bayesian framework to characterize the distribution of mean of the increment present above background for each of the radionuclides. The Bayesian model implemented allowed for the comparison of site-specific records to background concentrations to better approximate contamination attributed to the Site. A final screening step was employed for radionuclides that exceed background. This screening step compared 95% upper confidence limits (UCLs) from the increment distribution developed in the previous step to the risk screening levels. This approach yields a list of analytes that were determined to be elevated relative to background.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Crystal plasticity model of residual stress in additive manufacturing using the element elimination and reactivation method

Selective laser melting is receiving increasing interest as an additive manufacturing technique. Residual stresses induced by the large temperature gradients and inhomogeneous cooling process can favour the generation of cracks. In this work, a crystal plasticity finite element model is developed to simulate the formation of residual stresses and to understand the correlation between plastic deformation, grain orientation and residual stresses in the additive manufacturing process. The temperature profile and grain structure from thermal-fluid flow and grain growth simulations are implemented into the crystal plasticity model. An element elimination and reactivation method is proposed to model the melting and solidification and to reinitialize state variables, such as the plastic deformation, in the reactivated elements. The accuracy of this method is judged against previous method based on the stiffness degradation of liquid regions by comparing the plastic deformation as a function of time induced by thermal stresses. The method is used to investigate residual stresses parallel and perpendicular to the laser scan direction, and the correlation with the maximum Schmid factor of the grains along those directions. The magnitude of the residual stress can be predicted as a function of the depth, grain orientation and position with respect to the molten pool. The simulation results are directly comparable to X-ray diffraction experiments and stress–strain curves.

316 stainless steel↗
DOE OSTI2022

Why Is It So Challenging to Measure Residual Stresses ?

Abstract Background Residual stresses have a “hidden” character because they exist in a material without the presence of any external loads. They cannot easily be added or subtracted in a quantified manner, as is done when measuring applied stresses, and so are much more challenging to measure. Objective The objective here is to identify and describe the various features that make residual stress measurement methods challenging and to consider the ways that these challenges can be addressed in practice. Methods Various of the most common residual stress measurements methods are considered and the challenges associated with them are identified and classified. Results Five major challenges for residual stress measurements, and the approaches used for their resolution, are identified. Conclusions Despite the various challenges that need to be overcome, residual stress measurements can be successfully undertaken in practice. The most significant feature for success is a highly skilled and knowledge practitioner.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The Influence of Residual Stress on Fatigue Crack Growth Rates in Stainless Steel Processed by Different Additive Manufacturing Methods

The properties and microstructure of Type 304L stainless steel produced by two additive manufacturing (AM) methods—directed energy deposition (DED) and powder bed fusion (PBF)—are evaluated and compared. Localized heating and steep temperature gradients of AM processes lead to significant residual stress and distinctive microstructures, which may be process-specific and influence mechanical behavior. Test data show that materials produced by DED and PDF have small differences in tensile strengths but clear differences in residual stress and microstructural features. Measured fatigue crack growth rates (FCGRs) for cracks propagating parallel to and perpendicular to the build directions differ between the two AM materials. To separate the influences of residual stress and microstructure, K-control test procedures with decreasing and constant stress intensity factor ranges are used to measure FCGRs in the near-threshold regime (crack growth rates ≤ 1 × 10 −8 m/cycle). Residual stress is quantified by the residual stress intensity factor, K res , measured by the online crack compliance method. Correcting the FCGR data for differences in K res brings results for specimens of the two AM materials into agreement with each other and with results for wrought specimens, when the latter are corrected for crack closure. Differences in microstructure and tensile strength have an insignificant influence on FCGRs in these tests.

additive manufacturing↗
DOE OSTI2023

Microstructure and Residual Stress in Functionally Graded 316L Stainless Steel/Inconel 625 Alloys Fabricated by Direct Energy Deposition

Functionally graded materials (FGMs) provide a unique solution to combine distinct properties within a single component to enhance its overall performance. Understanding the microstructure and residual stress distribution is particularly important as the material dissimilarity in FGMs can result in high residual stress that affects the mechanical integrity of structural components. Here, this work aims to study the microstructure and residual stress of additively manufactured FGMs and the effects of isothermal annealing. In this study, 316L stainless steel/Inconel 625 FGMs were built by direct energy deposition, and characterized by optical and electron microscopy as well as synchrotron-based X-ray diffraction. Our study reveals that thermal annealing at 500°C for 3 h has minimal effects on the microstructure and chemistry of the graded materials, but effectively relieves the residual stress and leads to a uniform distribution of residual stress.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Characterization of microstructure and residual stress following the friction stir welding of dissimilar aluminum alloys

Friction-stir-welding (FSW) has gained importance as an effective way to join dissimilar materials due to its solid-state nature. However, FSW produces substantial residual stresses in aluminum welding, often deteriorating the component's structural performance and reliability. In the current study, the d-spacing (inter-atomic distance) of several locations on a battery tray and stress-free reference samples are measured with neutron diffraction to calculate the residual stresses in a lap 6061 to A365 dissimilar friction-stir-weld. Furthermore, the present study connects the measured residual stress to microstructure properties through electron backscatter diffraction (EBSD) and optical microscopy analyses. The EBSD results indicate that the FSW operation affects the grains’ orientation, thereby producing location-specific directionally varying elasticity across the weldment. Further, this varied elasticity creates unique d-spacing profiles even in the stress-free material. Additionally, the resulting stressed and stress-free d-spacing profiles show dependencies on the FSW tool geometry, traverse direction, and rotational direction. Lastly, this study suggests that the final component residual stress can be influenced by the sequence of multi-pass welds contributing to a rise in temperature in the presence of a completed weld relaxing its residual stress.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Smart material based multilayered microbeam structures for spatial self-deployment and reconfiguration: A residual stress approach

Alleviation of the potentially damaging effects induced by residual stresses was comprehensively investigated in previous research. Here, this paper, however, presents a spatially self-deployable and reconfigurable multilayered microbeam which takes advantage of residual stresses and shape memory effects. Reconfigurable mechanism of a typical four-layered microbeam composed of Pt\Ni 50 Ti 50 \Ni 50 Ti 50 \Pt is introduced, followed by analytical modeling of the maximum distance of the self-deployed gap as functions of variable structural and material parameters, including compressive residual stress in Pt layers and tensile residual stress in Ni 50 Ti 50 layers. Analytical solutions given by the static model agree well with the results obtained via finite element models (FEMs). Fabrication, characterization, and in-situ experiments were carried out to validate the feasibility of deployment of the as-released four-layered microbeam. The maximum distance of the gap was measured to be 41.39 μm at 20 °C, which could be increased to 51.73 μm thanks to controllable reconfiguration driven by shape memory effects. Theoretical analysis of such self-deployment and reconfiguration suggested a tensile residual stress increase by 52 MPa in Ni 50 Ti 50 layers. The multilayered microbeam structure with capabilities of self-deployment and reconfiguration offers great potential for various emerging applications, such as micro robotics, medical drug delivery devices, and intelligent chip scale spacecraft.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Residual elastic strain evolution due to thermal cycling of a ceramic-metal composite (WC-Cu) via high energy X-ray diffraction and analytical modeling

Residual stress, when superimposed with in-service loading, can significantly reduce the lifetime and performance of a component. Ceramic-metal composites are susceptible to residual stresses due to the thermal expansion mismatch of the ceramic and metallic phases. The WC-Cu composite explored in the present study provides a promising combination of thermal conductivity and strength properties, while exhibiting counterintuitive improvements in strength and ductility after thermal cycling. Further, this work quantifies the evolution of the residual elastic strains as a result of processing and cyclic thermal loading in a co-continuous WC-Cu composite through experimental high energy X-ray diffraction and kinetics-based modeling. Both analyses indicate that processing-induced residual tensile stress in the copper phase is relieved upon subsequent thermal cycling, with kinetics modeling revealing the cyclic-dependent nature of the active power-law creep mechanisms. The results indicate that, through stress relaxation, this material system maintains structural stability during thermal cycling. The illustrated kinetics of relaxation can inform general material processors and designers of ceramic-metal composites to minimize detrimental residual stress and improve performance of these material systems.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Correlation between microstructure and residual stress formation in friction stir welded armor steels characterized by neutron diffraction

Friction stir welding (FSW) is a solid-state joining process that minimizes the heat-affected zone (HAZ) compared with fusion-based arc welding, making it well suited for joining martensitic armor steels where hardness and ballistic resistance are critical. This study investigates residual stress formation in three defect-free FSW butt-joint configurations relevant to armored-vehicle fabrication: similar rolled homogeneous armor (RHA–RHA, Case 1), similar high-hardness armor (HHA–HHA, Case 2), and dissimilar HHA–RHA (Case 3) joints produced under temperature-controlled conditions (770 °C). Neutron diffraction was employed to quantify the magnitude and spatial distribution of residual stresses in the longitudinal, transverse, and normal directions and to correlate them with weld microstructure and hardness. Tensile residual stresses were concentrated in the softened HAZ, reaching approximately 300 MPa for Case 2 and 400 MPa for Case 1 (≈50–70 % of the base-metal yield strength; ∼581 MPa for RHA and ∼566 MPa for HHA), while compressive residual stresses dominated the stir zone. The spatial extent of tensile stresses scaled with the width of the softened HAZ, which was largest in the dissimilar HHA–RHA joint and smallest in the HHA–HHA joint. Full-width-at-half-maximum (FWHM) analysis revealed low microstrain in overtempered HAZ regions and high microstrain in the stir zone associated with severe plastic deformation and fresh martensite formation. This work demonstrates that residual stress evolution in FSW of martensitic armor steels is governed not primarily by peak temperature or thermal contraction, as inferred from fusion-welding analogies, but by the competition between transformation-induced volumetric expansion and tempering-induced stress relaxation. The relative dominance of these mechanisms is shown to depend on alloy hardenability and local thermal history, leading to more extensive HAZ softening and broader tensile stress regions in the lower-hardenability RHA steel. These findings establish a transferable mechanistic framework for optimizing solid-state joining strategies in high-strength steels and other transformation-hardening alloys beyond armor applications.

Friction stir welding↗
DOE OSTI2021

Measuring residual stress in Ti-6Al-4V with HR-EBSD, using reference patterns from annealed material

In this study, elastic strain and residual stress values in an engineering material were determined by high-resolution EBSD (HR-EBSD) using reference patterns from annealed, recrystallized material. Specifically, rolled Ti-6Al-4V sheet was analyzed using HR EBSD in both an as-annealed and a strained state, the latter established via a static two-point bend fixture. The commercial software CrossCourt4 (CC4) was used to evaluate the relative intragranular strain tensor components of the alpha grains mapped by HR-EBSD. The intragranular reference patterns identified in each grain by the software were then replaced with similarly-oriented patterns from scans of the as-annealed, recrystallized material. The CC4 analysis was then repeated to provide calibrated strain and residual stress values. Elastic strains on the order of 10–3 were detected, with corresponding residual stress values on the order of 1 GPa. Subsequent analyses using high energy synchrotron x-ray diffraction showed good correlation with the elastic strains measured by HR-EBSD using the annealed reference patterns. Additionally, the maximum macroscopic stress analytically predicted for two-point bending was in agreement with the residual stress observed. Good repeatability of the methodology and insight into the state of individual grains were also observed. The findings provide encouraging evidence that accurate intragranular and long-range residual stress measurements of engineering significance can be made with HR-EBSD using a physical reference pattern library.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The impact of residual solvent on catholyte performance in solid-state batteries

All-solid-state batteries (ASSBs) are attractive due to their safety, use of the Li metal anode, high energy density, and innovative processing routes. However, high interfacial resistance, especially on the cathode side, is one of the major challenges for commercialization of ASSBs. Catholyte, either a liquid or solid, is added to lower the cathode/electrolyte interfacial resistance. In this study, we find that residual N-methylpyrrolidone solvent remaining in a PVDF/LiTFSI solid polymer catholyte after incomplete drying can dramatically lower the interfacial resistance between the Li 6.25 Al 0.25 La 3 Zr 2 O 12 electrolyte and LiNi 1/3 Mn 1/3 Co 1/3 O 2 cathode-active material. Cells with varying amounts of residual solvent are compared to optimize the residual solvent loading. With moderate residual solvent, the discharge capacity reaches 142 mA h g -1 when cycled at 25 °C and 0.5 C and the capacity retention is 60.5% after 125 cycles. Discharge capacity retention is improved at -10 °C. The conductivity of the free-standing PVDF/LiTFSI film, mimicking the PVDF/LiTFSI catholyte, verifies the role of residual NMP in the cathode. Finally, this study demonstrates the possibility of widely differing results for ASSBs when the cathode is not completely dried. Also, it provides a hint for a potential method to lower the cathode/electrolyte interfacial resistance.

25 ENERGY STORAGE↗
DOE OSTI2020

Control of Weld Residual Stress in a Thin Steel Plate through Low Transformation Temperature Welding Consumables

Low transformation temperature welding (LTTW) consumables are characterized by a low martensite start temperature and a large fraction of martensite forming in the weld. It can efficiently reduce the tensile residual stress because the volume expansion associated with the martensitic transformation compensates for the thermal contraction during cooling. In this work, a LTTW wire, designated as EH200B, was created for the arc welding of advanced high-strength steel thin plates. In comparison to conventional ER70S-3 wires, this LTTW wire generated an opposite distortion pattern. Neutron diffraction measurements along the center thickness of the welded plates showed the maximum residual stress along the longitudinal direction (LD) in the weld region, and the heat-affected zone (HAZ) immediately adjacent to the weld region was reduced from ~330 MPa to below 240 MPa by using the LTTW wire. A finite element (FE) model was developed to predict the residual stress distributions of the plates welded under these two wires. The simulation results showed reasonable agreement with the volume-average neutron diffraction data. Compressive residual stress in the weld region using the LTTW wire was predicted by the FE method. Electron backscattered diffraction and x-ray diffraction measurements confirmed ~90% martensite was present in the LTTW weld. The fatigue life of DP980 steel lap joint panels using EH200B wire nearly doubled that of ER70S-3 wire. This improvement was attributed to the high strength and low LD residual stress in the weld and HAZ immediately adjacent to the weld.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Study of Mechanical Properties, Microstructure, and Residual Stresses of AISI 304/304L Stainless Steel Submerged Arc Weld for Spent Fuel Dry Storage Systems

The confinement boundaries of spent nuclear fuel (SNF) canisters are typically fusion welded. Welded microstructures, strain hardening, and residual stresses combined with a chemically aggressive, chloride-rich environment led to concerns that the welded canister may be susceptible to chloride-induced stress corrosion cracking (CISCC). A comprehensive understanding of the modification of stainless steel (SS) metallurgical and mechanical properties by fusion welding could accelerate the predictive analysis of CISCC susceptibility. This paper describes a submerged arc welding (SAW) procedure that was developed and qualified on 12.7 mm (0.5 in.) thick AISI 304/304L SS to produce joints in a way similar to actual SNF canister manufacturing. This procedure has the potential to reduce the production cost and weld CISCC susceptibility by using fewer welding passes and lower heat input than current industrial applications. Global and local mechanical behaviors and properties, as well as residual stress distributions on the welded joint, were studied. The results indicate that hardness values in the fusion zone (FZ) and heat-affected zone (HAZ) are slightly higher than that of the base metal. Strain localization was presented in the HAZ before the tensile stress reached its maximum value, and then it shifted to the FZ. The specimen finally broke in the FZ. High tensile residual stresses exhibited in the FZ and the nearby HAZ suggest the highest CISCC-susceptible spots. The maximum tensile residual stresses were along the welding direction, indicating that if cracks occur, they would be perpendicular to the welding direction. This study involved developing and qualifying a SAW procedure for SNF canister production. The new procedure yielded cost savings (SAW working efficiency increased by about 80%), improved mechanical properties, and presented moderate residual stresses. Analysis revealed that the welded joint’s low-stress and high-stress damage assessments may be affected by shifts in the strain localization spot under loading.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRSDate not supplied

RESIDUAL DEFORMATION ANALYSIS IN COMPOSITE SHELL STRUCTURES MANUFACTURED USING AUTOMATED FIBER PLACEMENT

The manufacturing of composites typically produces residual stresses that can significantly affect the final shape of the structure. The process of automated fiber placement (AFP) has become a prominent manufacturing technique in developing layups with tailored, variable stiffness morphology. The steered patterns of fiber tows with and without overlaps produce residual deformations that are distinctive from traditional layups. Digital image correlation was used to measure the AFP lamina coefficients of thermal expansion, which were incorporated into finite element analyses (FEA) to model the cooling phase of the cure cycle. The effects of nonlinear analysis and temperature-dependent lamina properties calculated using self-consistent field micromechanics, on the resulting residual deformation of shells, were also modeled. The predicted residual deformation was analyzed by considering out-of-roundness in cylindrical shells and compared to the experimental results. The shell FEA results were well-correlated with the overall deformed shape of the AFP cylinder with overlaps, while the shell FEA model of the AFP cylinder without overlaps did not show as good of qualitative match of the deformation pattern. Analytical correlation with measured results were insensitive to material softening at elevated temperatures, geometric nonlinearities, and variations in measured lamina thermal properties. To improve the accuracy of the residual deformation analysis, these results suggest that the thermo-chemical shrinkages preceding the cooldown should be considered, as well as possible variations in ply level microstructure due to the presence of the embedded fiber tow gaps and overlaps.

Composites↗
NASA NTRSDate not supplied

Geometric Sensitivity of Residual Fields in Metal Additive Manufacturing

The sensitivity of geometrical parameters on the residual stress and distortion as computed by a metal additive manufacturing simulation is presented. A nozzle-like geometry was chosen with its length, wall thickness, and outer radius varied. A Latin hypercube sampling of 300 specimens produced the combinations of the geometrical parameters. Full thermomechanical simulations predicted the residual fields. Statistical analysis including regression curves shows that there is a strong correlation between these residual fields and the geometry, hinting that it may be possible to predictably influence the residual displacements and residual stresses by varying the overall geometry.

Multiscale Modeling↗
DOE OSTI2021

LX-17 Thermal Decomposition-Characterization of Solid Residues from Cook-Off in a Small-Scale Vessel Under Confinement

Concerns surround whether insensitive (or any) energetic materials are more dangerous to handle when exposed to abnormal thermal environments. This study characterizes the residual material remaining after LX-17 (92.5 % 1,3,5-triamino 2,4,6-trinitro benzene (TATB) and 7.5 % Kel-F) is exposed to various thermal environments in a sealed small-scale vessel cook-off test reactor (heated at 0.1 to 100 °C/min until the reactor opened at 3000 psi (20.7 MPa)). Previous work has shown no additional sensitivity of these residues as evaluated by small-scale safety analysis, but characterization on the molecular scale indicates the TATB is transformed to more reactive compounds as well as the residue could be precursors to toxic gases. The solids and chars were characterized by various analytical methods. Heat-flow measurements indicated exothermic release is due to a mixture of residual TATB and related decomposition products (which may be more energetic). The N/C and O/N ratios indicated a material much more degraded than TATB. Primarily, the solids were a network of amorphous C inter-dispersed with N and O. Types of bonding include C–C, C–N, N–H, N–C, N=C, N≡C, C–O=, and –OH. Solvent extracts of the solids showed TATB decomposition intermediates benzo-furazans and benzo-furoxans, substituted TATB (mono-nitroso, hydroxyl, and chlorinated) along with several unidentified smaller molecules. These results indicate thermal treatment produces an amorphous carbon residue with heteroatoms incorporated through differing functionality, varying depending upon the thermal severity of exposure. These structures also could further decompose producing toxic light gases (such as cyanide).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Control of machining-induced residual stress via tool geometry and process parameter modification

Distortion generated in machined, monolithic, thin-walled aerospace components due to residual stresses leads to significant material and economic waste in the manufacturing industry. Inherent residual stress (IRS) present in stock materials combines with machining-induced residual stress (MIRS) to influence the final machined part distortion. It is hypothesized that MIRS can be controlled, based on the part geometry, through deliberate cutting tool geometry and process parameter modifications to negate the effect of IRS on distortion, consequently resulting in distortion-free parts. A finite element (FE) orthogonal cutting model is developed to study how tool geometry and process parameters influence machining-induced residual stress (MIRS). Orthogonal cutting experiments are performed on Al 7075-T651 samples to measure cutting forces and MIRS. A cutting force dynamometer is used to measure forces during cutting and a novel digital image correlation (DIC) based hole drilling technique is employed to measure the near-surface residual stress (RS) in the cut samples. These data are subsequently utilized to validate the FE prediction model. Various cases of cutting simulations involving different depths of cut, tool tip radii, and rake angles are performed to study their effects on RS. Similar to prior literature, increasing the depth of cut, tool tip radius, or rake angle is found to promote the formation of near-surface tensile stresses. The competing effects of material plowing and temperature are shown to determine the type of RS at the end of the cut. Moreover, a window of variation of RS (up to ± 400 MPa) is estimated within the given range of conditions, allowing for the control of MIRS through tool and process modification.

Mathews, Ritin [ORNL] (ORCID:0000000301440828)↗
DOE OSTI2020

Complementary Measurements of Residual Stresses Before and After Base Plate Removal in an Intricate Additively-Manufactured Stainless-Steel Valve Housing

Residual stress measurements using neutron diffraction and the contour method were performed on a valve housing made from 316 L stainless steel powder with intricate three-dimensional internal features using laser powder-bed fusion additive manufacturing. The measurements captured the evolution of the residual stress fields from a state where the valve housing was attached to the base plate to a state where the housing was cut free from the base plate. Making use of this cut, thus making it a non-destructive measurement in this application, the contour method mapped the residual stress component normal to the cut plane (this stress field is completely relieved by cutting) over the whole cut plane, as well as the change in all stresses in the entire housing due to the cut. The non-destructive nature of the neutron diffraction measurements enabled measurements of residual stress at various points in the build prior to cutting and again after cutting. Good agreement was observed between the two measurement techniques, which showed large, tensile build-direction residual stresses in the outer regions of the housing. The contour results showed large changes in multiple stress components upon removal of the build from the base plate in two distinct regions: near the plane where the build was cut free from the base plate and near the internal features that act as stress concentrators. These observations should be useful in understanding the driving mechanisms for builds cracking near the base plate and to identify regions of concern for structural integrity. Neutron diffraction measurements were also used to show the shear stresses near the base plate were significantly lower than normal stresses, an important assumption for the contour method because of the asymmetric cut.

36 MATERIALS SCIENCE↗