Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reverse Engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Effect of forward velocity and crosswind on the reverse-thrust performance of a variable-pitch fan engine

Variable-pitch-fan engines may be attractive for future short-haul aircraft if sufficient reverse thrust is available for aircraft deceleration after touchdown. Thrust reversal is obtained in these engines by changing fan blade pitch about 90 deg, which causes the fan airflow to enter the fan duct nozzle and exhaust through the fan inlet. This capability would eliminate the heavy and costly thrust reverser system required for current fixed-pitch turbofan engines. NASA has, therefore, supported the development of advanced technology for a quiet, clean, high-bypass-ratio turbofan engine for future short-haul aircraft. In connection with this program, tests were conducted to determine the effect of forward velocity and angle of attack on steady-state reverse-thrust performance. Other objectives of the tests were related to the determination of the effect of forward velocity on forward-to-reverse thrust transient performance and the determination of the effectiveness of an overshoot blade angle technique to establish reverse thrust during a transient. The results of the tests are discussed.

Reemsnyder, D. C.↗
NASA NTRS1974

Wind tunnel test of model target thrust reversers for the Pratt and Whitney aircraft JT8D-100 series engines installed on a 727-200 airplane

The results of a low speed wind tunnel test of 0.046 scale model target thrust reversers installed on a 727-200 model airplane are presented. The full airplane model was mounted on a force balance, except for the nacelles and thrust reversers, which were independently mounted and isolated from it. The installation had the capability of simulating the inlet airflows and of supplying the correct proportions of primary and secondary air to the nozzles. The objectives of the test were to assess the compatibility of the thrust reversers target door design with the engine and airplane. The following measurements were made: hot gas ingestion at the nacelle inlets; model lift, drag, and pitching moment; hot gas impingement on the airplane structure; and qualitative assessment of the rudder effectiveness. The major parameters controlling hot gas ingestion were found to be thrust reverser orientation, engine power setting, and the lip height of the bottom thrust reverser doors on the side nacelles. The thrust reversers tended to increase the model lift, decrease the drag, and decrease the pitching moment.

Hambly, D.↗
NASA NTRS1984

Interference effects of thrust reversing on horizontal tail effectiveness of twin-engine fighter aircraft at Mach numbers from 0.15 to 0.90

An investigation was conducted in the Langley 16 foot Transonic Tunnel to determine the interference effects of thrust reversing on horizontal tail effectiveness of a twin engine, general research fighter model at approach and in-flight speeds. Twin vertical tails at three longitudinal locations were tested at a cant angle of 0 deg. One configuration was also tested at a cant angle of 20 deg. Two nonaxisymmetric nozzle reverser concepts were studied. Test data were obtained at Mach numbers of 0.15, 0.60, and 0.90 and at angles of attack from -3 to 9 deg. Nozzle pressure ratios varied from jet off to 7.0, depending upon Mach number. At landing approach speed (Mach number 0.15), thrust reverser operation usually resulted in large variations (up to 70% increase) in horizontal tail effectiveness as nozzle pressure ratio was varied at zero angle of attack or as angle of attack was varied at constant nozzle pressure ratio. There was always a decrease in effectiveness at Mach numbers of 0.60 and 0.90 as a result of reverser operation.

Capone, F. J.↗
NASA NTRS1983

Thrust reversing effects on horizontal tail effectiveness of twin-engine fighter aircraft

The Langley Research Center has conducted an experimental program to determine the interference effects of thrust reversing on horizontal tail effectiveness of a twin engine, general research fighter model at approach (Mach number 0.15) and in-flight (Mach number 0.60 and 0.90) speeds. Twin vertical tails were tested at three longitudinal locations. Two nonaxisymmetric nozzle reverser concepts were studied. The effects of thrust reversing on horizontal tail effectiveness were found to be very dependent upon vertical tail locations. At approach speeds thrust reverser operation usually resulted in large variations in horizontal tail effectiveness as either nozzle pressure ratio or model angle of attack was varied. Either increases or decreases in tail effectiveness ocurred due to reverse operation depending upon tail location. At in-flight conditions there were always decreases in tail effectiveness due to reverser operation regardless of vertical tail location.

Capone, F. J.↗
NASA NTRS1973

An airline study of advanced technology requirements for advanced high speed commercial transport engines. 1: Engine design study assessment

The advanced technology requirements for an advanced high speed commercial tranport engine are presented. The results of the phase 1 study effort cover the following areas: (1) statement of an airline's major objectives for future transport engines, (2) airline's method of evaluating engine proposals, (3) description of an optimum engine for a long range subsonic commercial transport including installation and critical design features, (4) discussion of engine performance problems and experience with performance degradation, (5) trends in engine and pod prices with increasing technology and objectives for the future, (6) discussion of the research objectives for composites, reversers, advanced components, engine control systems, and devices to reduce the impact of engine stall, and (7) discussion of the airline objectives for noise and pollution reduction.

Sallee, G. P.↗
NASA NTRS1936

Combustion-engine Temperatures by the Sodium Line-reversal Method

The sodium line-reversal method has been used in some preliminary measurements of flame temperature. Improvements in the method involving a photographic recorder and a means of correcting for the dirtiness of the windows are described. The temperatures so obtained are compared with those calculated from pressure diagrams.

Brevoort, Maurice J↗
NASA NTRS1982

Nacelle Design

Rohr Industries, Inc. specializes in the manufacturing of nacelles, thrust reversers, and other engine components, has made use of the COSMIC program in nacelle work for aircraft like the McDonnell Douglas DC-10, the French/German Airbus and the Boeing 727, 737 and 747 jetliners. They also manufacture complete nacelles for military and business aircraft and are supplying nacelle components for the Boeing 757. The nacelle requires research and development for each type of airplane because of complex airflows around the engine inlet and high pressures on the nacelle skin. The use of the computer program defines the airflow field around turbofan engine nacelle inlet and cowls. Pressures on the nacelle skin are estimated for various flight conditions and structural integrity of the nacelle design. Rohr estimates that use of this program saved six man-months of programmer time necessary to develop alternative software.

Source record↗
NASA NTRS2014

Modeling the Deterioration of Engine and Low Pressure Compressor Performance During a Roll Back Event Due to Ice Accretion

The main focus of this study is to apply a computational tool for the flow analysis of the engine that has been tested with ice crystal ingestion in the Propulsion Systems Laboratory (PSL) of NASA Glenn Research Center. A data point was selected for analysis during which the engine experienced a full roll back event due to the ice accretion on the blades and flow path of the low pressure compressor. The computational tool consists of the Numerical Propulsion System Simulation (NPSS) engine system thermodynamic cycle code, and an Euler-based compressor flow analysis code, that has an ice particle melt estimation code with the capability of determining the rate of sublimation, melting, and evaporation through the compressor blade rows. Decreasing the performance characteristics of the low pressure compressor (LPC) within the NPSS cycle analysis resulted in matching the overall engine performance parameters measured during testing at data points in short time intervals through the progression of the roll back event. Detailed analysis of the fan-core and LPC with the compressor flow analysis code simulated the effects of ice accretion by increasing the aerodynamic blockage and pressure losses through the low pressure compressor until achieving a match with the NPSS cycle analysis results, at each scan. With the additional blockages and losses in the LPC, the compressor flow analysis code results were able to numerically reproduce the performance that was determined by the NPSS cycle analysis, which was in agreement with the PSL engine test data. The compressor flow analysis indicated that the blockage due to ice accretion in the LPC exit guide vane stators caused the exit guide vane (EGV) to be nearly choked, significantly reducing the air flow rate into the core. This caused the LPC to eventually be in stall due to increasing levels of diffusion in the rotors and high incidence angles in the inlet guide vane (IGV) and EGV stators. The flow analysis indicating compressor stall is substantiated by the video images of the IGV taken during the PSL test, which showed water on the surface of the IGV flowing upstream out of the engine, indicating flow reversal, which is characteristic of a stalled compressor.

Veres, Joseph P.↗
NASA NTRS2014

Modeling the Deterioration of Engine and Low Pressure Compressor Performance During a Roll Back Event Due to Ice Accretion

The main focus of this study is to apply a computational tool for the flow analysis of the engine that has been tested with ice crystal ingestion in the Propulsion Systems Laboratory (PSL) of NASA Glenn Research Center. A data point was selected for analysis during which the engine experienced a full roll back event due to the ice accretion on the blades and flow path of the low pressure compressor. The computational tool consists of the Numerical Propulsion System Simulation (NPSS) engine system thermodynamic cycle code, and an Euler-based compressor flow analysis code, that has an ice particle melt estimation code with the capability of determining the rate of sublimation, melting, and evaporation through the compressor blade rows. Decreasing the performance characteristics of the low pressure compressor (LPC) within the NPSS cycle analysis resulted in matching the overall engine performance parameters measured during testing at data points in short time intervals through the progression of the roll back event. Detailed analysis of the fan-core and LPC with the compressor flow analysis code simulated the effects of ice accretion by increasing the aerodynamic blockage and pressure losses through the low pressure compressor until achieving a match with the NPSS cycle analysis results, at each scan. With the additional blockages and losses in the LPC, the compressor flow analysis code results were able to numerically reproduce the performance that was determined by the NPSS cycle analysis, which was in agreement with the PSL engine test data. The compressor flow analysis indicated that the blockage due to ice accretion in the LPC exit guide vane stators caused the exit guide vane (EGV) to be nearly choked, significantly reducing the air flow rate into the core. This caused the LPC to eventually be in stall due to increasing levels of diffusion in the rotors and high incidence angles in the inlet guide vane (IGV) and EGV stators. The flow analysis indicating compressor stall is substantiated by the video images of the IGV taken during the PSL test, which showed water on the surface of the IGV flowing upstream out of the engine, indicating flow reversal, which is characteristic of a stalled compressor.

Jorgenson, Philip C. E.↗
NASA NTRS1972

Effects of an in-flight thrust reverser on the stability and control characteristics of a single-engine fighter airplane model

The changes in thrust minus drag performance as well as longitudinal and directional stability and control characteristics of a single-engine jet aircraft attributable to an in-flight thrust reverser of the blocker-deflector door type were investigated in a 16-foot transonic wind tunnel. The longitudinal and directional stability data are presented. Test conditions simulated landing approach conditions as well as high speed maneuvering such as may be required for combat or steep descent from high altitude.

Mercer, C. E.↗
NASA NTRS1979

Effect of forward velocity and crosswind on the reverse-thrust performance of a variable-pitch fan engine

A full-size variable-pitch fan engine was tested in the Ames 40 by 80 foot wind tunnel to determine the effect of forward velocity and crosswind on reverse-thrust performance. Two flight-type inlet configurations were tested, and a flared fan nozzle was installed as an inlet for reverse-thrust operation. Steady-state reverse-thrust performance was obtained up to 54 m/s (105 knots). An abrupt decrease in reverse thrust occurred at about 30 m/s (60 knots). Reverse thrust was established following forward-to-reverse thrust transients both statically and with forward velocities only up to 30 m/s.

Reemsnyder, D. C.↗
NASA NTRS1974

Reversed cowl-flap thrust augmentor

Inlet mouthpiece with variable geometry improves low-speed performance of inlet (or ejector) of jet engines by use of reversed cowl-flap mechanism. Flaps can be adjusted mechanically or system can be operated with pressure taps set so pressure on inlet face is always smaller than pressure on back of inlet.

Cheng, D. Y.↗
NASA NTRSDate not supplied

Computational Assessment of Inlet Backflow Effects on Rotating Detonation Engine Performance and Operability

The performance impact of flow reversal at the inlet of an airbreathing rotating detonation engine (RDE) is investigated using 2 and 3-dimensional computational fluid dynamic (CFD) simulations. Flow reversal, or backflow, occurs in RDE inlets in the high-pressure region directly behind the rotating detonation front. This is also where most of the engine thrust or pressure gain is produced. The amount of backflow relative to throughflow depends on the inlet design. For the present work, a simple annular ‘slit’ design is used. The simulations are idealized in several ways, including that fuel and air are premixed, but prevented from reacting when within the inlet region. The results indicate that even with idealizations, the impact of inlet backflow on pressure gain can be substantial. The simulations also reveal an intriguing instability that develops in certain configurations. The mass flow rate into the RDE begins to oscillate at a regular frequency that is substantially less than the detonation rotational frequency. This is accompanied by oscillations in the detonation height. The oscillation amplitude grows over time until the detonation ultimately fails. Both the performance and instability results emphasize the need for carefully designed RDE inlets that provide low loss when flow is in the forward direction, but high resistance when the flow is reversed. Development of such high-diodicity inlets is critical to achieving pressure gain in airbreathing RDE’s.

Detonation↗
NASA NTRSDate not supplied

Computational Assessment of Inlet Backflow Effects on Rotating Detonation Engine Performance and Operability

The performance impact of flow reversal at the inlet of an airbreathing rotating detonation engine (RDE) is investigated using 2 and 3-dimensional computational fluid dynamic (CFD) simulations. Flow reversal, or backflow, occurs in RDE inlets in the high-pressure region directly behind the rotating detonation front. This is also where most of the engine thrust or pressure gain is produced. The amount of backflow relative to throughflow depends on the inlet design. For the present work, a simple annular ‘slit’ design is used. The simulations are idealized in several ways, including that fuel and air are premixed, but prevented from reacting when within the inlet region. The results indicate that even with idealizations, the impact of inlet backflow on pressure gain can be substantial. The simulations also reveal an intriguing instability that develops in certain configurations. The mass flow rate into the RDE begins to oscillate at a regular frequency that is substantially less than the detonation rotational frequency. This is accompanied by oscillations in the detonation height. The oscillation amplitude grows over time until the detonation ultimately fails. Both the performance and instability results emphasize the need for carefully designed RDE inlets that provide low loss when flow is in the forward direction, but high resistance when the flow is reversed. Development of such high-diodicity inlets is critical to achieving pressure gain in airbreathing RDE’s.

detonation↗
NASA NTRS1980

Development of a Kevlar/PMR-15 reduced drag DC-9 nacelle fairing

The paper describes an advanced composite fairing designed to reduce drag on DC-9 nacelles as a part of the NASA Engine Component Improvement Program. This fairing is the aft enclosure for the thrust reverser actuator system on JT8D engine nacelles and is subjected to a 500 F exhaust flow during the reverse thrust. A reduced-drag configuration was developed by using in-flight tuft surveys for flow visualization in order to identify areas with low-quality flow, and then modifying the aerodynamic lines to improve the flow. A fabrication method for molding the part in an autoclave was developed; this material system is suitable for 500 F. The resultant composite fairing reduces the overall aircraft drag 1% with a weight reduction of 40% when compared with a metal component.

Kawai, R. T.↗
NASA NTRS1987

Full-scale thrust reverser testing in an altitude facility

A two-dimensional convergent-divergent exhaust nozzle designed and fabricated by Pratt and Whitney Aircraft was installed on a PW1128 turbofan engine and tested during thrust reverser operation in an altitude facility at NASA Lewis Research Center. A unique collection system was used to capture the thrust reverser exhaust gas and transport it to the primary exhaust collector. Tests were conducted at three flight conditions with varying amounts of thrust reverse at each condition. Some reverser exhaust gas spillage by the collection system was encountered but engine performance was unaffected at all flight conditions tested. Based on the results of this test program, the feasibility of altitude testing of advanced multi-function exhaust nozzle systems has been demonstrated.

Mehalic, Charles M.↗
NASA NTRS1987

Full-scale thrust reverser testing in an altitude facility

A two-dimensional convergent-divergent exhaust nozzle designed and fabricated by Pratt and Whitney Aircraft was installed on a PW1128 turbofan engine and tested during thrust reverser operation in an altitude facility at NASA Lewis Research Center. A unique collection system was used to capture the thrust reverser exhaust gas and transport it to the primary exhaust collector. Tests were conducted at three flight conditions with varying amounts of thrust reverse at each condition. Some reverser exhaust gas spillage by the collection system was encountered but engine performance was unaffected at all flight conditions tested. Based on the results of this test program, the feasibility of altitude testing of advanced multifunction exhaust nozzle systems has been demonstrated.

Mehalic, Charles M.↗
NASA NTRS1974

Results from cascade thrust reverser noise and suppression experiments

Results from experimental work on model scale cascade reversers with cold airflow are presented. Sound power level directivity and spectral characteristics for cascade reversers are reported. Effect of cascade exit area ratio, vane profile shape, and emission arc are discussed. Model equivalent diameters varied from 3 to 5 inches, pressure ratios range from 1.15 to 3.0. Depending on the reverser type, acoustic power was proportional to the 4 1/2 to 6th power of ideal jet velocity. Reverser noise peaked at higher frequency and was more omnidirectional than nozzle-alone jet noise. Appreciable reduction in sideline noise was obtained from plane shields. Airfoil-vaned cascades were the most aerodynamically efficient and least noisy reversers. Scaling of cascade reverser data to example aircraft engines showed all cascades above the 95 PNdB sideline goal from STOL aircraft. However, the airfoil-vaned reverser has a good potential for meeting this goal for high-bypass (low pressure ratio) exhausts.

Gutierrez, O. A.↗