SEARCH · Search NASA

Results for “Rotor Aerodynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS1995

Aerodynamic Evaluation of Two Compact Radial-Inflow Turbine Rotors

The aerodynamic evaluation of two highly loaded compact radial turbine rotors was conducted at the NASA Lewis Research Center Small Engine Component Test Facility (SECTF). The experimental results were used for proof-of-concept, for modeling radial inflow turbine rotors, and for providing data for code verification. Two rotors were designed to have a shorter axial length, up to a 10-percent reduced diameter, a lighter weight, and equal or higher efficiencies with those of conventional radial inflow turbine rotors. Three configurations were tested: rotor 1, having a 40-percent shorter axial length, with the design stator (stator 1); rotor 1 with the design stator vanes closed down (stator 2); and rotor 2, slightly shorter axially and having higher loading, with stator 2. The stator had 36 vanes and the rotors each had 14 solid blades. Although presently uncooled, the rotor blades were designed for thicknesses which would allow cooling passages to be added. The overall stage performance measurements and the rotor and stator exit flow field surveys were obtained. Measurements of steady state temperatures, pressures, mass flow rates, flow angles, and output power were made at various operating conditions. Data were obtained at corrected speeds of 80, 90, 100, 110, and 120 percent of design over a range of equivalent inlet-to-exit pressure ratios of 3.5, 4.0, 4.5, and 5.0, the maximum pressure ratio achieved. The test showed that the configuration of rotor 1 with stator 1 running at the design pressure ratio produced a flow rate which was 5.6 percent higher than expected. This result indicated the need to close down the stator flow area to reduce the flow. The flow area reduction was accomplished by restaggering the vanes. Rotor 1 was retested with the closed-down stator vanes and achieved the correct mass flow. Rotor 2 was tested only with the restaggered vanes. The test results of the three turbine configurations were nearly identical. Although the measured efficiencies of the compact designs fell 2 to 3 points below the predicted efficiency of 91 percent, they did meet and exceed by up to 2.5 percentage points the efficiences of state-of-the-art turbines found in the literature.

Simonyi, P. Susan↗

DOE OSTI2023

On the characteristics of the wake of a wind turbine undergoing large motions caused by a floating structure: an insight based on experiments and multi-fidelity simulations from the OC6 project Phase III

This study reports the results of the second round of analyses of the Offshore Code Comparison, Collaboration, Continued, with Correlation and unCertainty (OC6) project Phase III. While the first round investigated rotor aerodynamic loading, here, focus is given to the wake behavior of a floating wind turbine under large motion. Wind tunnel experimental data from the UNsteady Aerodynamics for FLOating Wind (UNAFLOW) project are compared with the results of simulations provided by participants with methods and codes of different levels of fidelity. The effect of platform motion on both the near and the far wake is investigated. More specifically, the behavior of tip vortices in the near wake is evaluated through multiple metrics, such as streamwise position, core radius, convection velocity, and circulation. Additionally, the onset of velocity oscillations in the far wake is analyzed because this can have a negative effect on stability and loading of downstream rotors. Results in the near wake for unsteady cases confirm that simulations and experiments tend to diverge from the expected linearized quasi-steady behavior when the rotor reduced frequency increases over 0.5. Additionally, differences across the simulations become significant, suggesting that further efforts are required to tune the currently available methodologies in order to correctly evaluate the aerodynamic response of a floating wind turbine in unsteady conditions. Regarding the far wake, it is seen that, in some conditions, numerical methods overpredict the impact of platform motion on the velocity fluctuations. Moreover, results suggest that the effect of platform motion on the far wake, differently from original expectations about a faster wake recovery in a floating wind turbine, seems to be limited or even oriented to the generation of a wake less prone to dissipation.

17 WIND ENERGY↗

NASA NTRS2000

A Novel Method for Reducing Rotor Blade-Vortex Interaction

One of the major hindrances to expansion of the rotorcraft market is the high-amplitude noise they produce, especially during low-speed descent, where blade-vortex interactions frequently occur. In an attempt to reduce the noise levels caused by blade-vortex interactions, the flip-tip rotor blade concept was devised. The flip-tip rotor increases the miss distance between the shed vortices and the rotor blades, reducing BVI noise. The distance is increased by rotating an outboard portion of the rotor tip either up or down depending on the flight condition. The proposed plan for the grant consisted of a computational simulation of the rotor aerodynamics and its wake geometry to determine the effectiveness of the concept, coupled with a series of wind tunnel experiments exploring the value of the device and validating the computer model. The computational model did in fact show that the miss distance could be increased, giving a measure of the effectiveness of the flip-tip rotor. However, the wind experiments were not able to be conducted. Increased outside demand for the 7'x lO' wind tunnel at NASA Ames and low priority at Ames for this project forced numerous postponements of the tests, eventually pushing the tests beyond the life of the grant. A design for the rotor blades to be tested in the wind tunnel was completed and an analysis of the strength of the model blades based on predicted loads, including dynamic forces, was done.

Glinka, A. T.↗

NASA NTRS1986

Individual-blade-control research in the MIT VTOL Technology Laboratory 1977-1985

A new, advanced system for active control of helicopters and its application to the solution of rotor aerodynamic and aeroelastic problems is described. Each blade is individually controlled in the rotating frame over a wide range of frequencies. Application of the system to gust alleviation, attitude stabilization, vibration alleviation, blade lag damping augmentation, stall flutter suppression, blade flapping stabilization, stall alleviation, and performance enhancement is outlined. The effectiveness of the system in achieving most of these applications is demonstrated by experimental results from wind tunnel tests of a model helicopter rotor with individual blade control. The feasibility of achieving many or all of the applications of individual blade control using the conventional helicopter swash plate is demonstrated, and the necessary control laws are presented.

Ham, N. D.↗

NASA NTRS1986

Helicopter individual-blade-control research at MIT 1977-1985

A new advanced system for active control of helicopters and its application to the solution of rotor aerodynamic and aeroelastic problems is described. Each blade is individually controlled in the rotating frame over a wide range of frequencies. Application of the system to gust alleviation, attitude stabilization, vibration alleviation, blade lag damping augmentation, stall flutter suppression, blade flapping stabilization, stall alleviation, and performance enhancement is outlined. The effectiveness of the system in achieving most of these applications is demonstrated by experimental results from wind tunnel tests of a model helicopter rotor with individual blade control. The feasibility of achieving many or all of the applications of individual blade control using the conventional helicopter swash plate is demonstrated, and the necessary control laws are presented.

Ham, Norman D.↗

NASA NTRSDate not supplied

Structural Analysis of Load-Bearing Components in Mars Science Helicopter

The successful demonstration of powered flight on Mars by Ingenuity has led to the development of next generation Martian rotorcraft. As technology advances from a technology demonstrator to possible expanded planetary science investigations, the potential to fly a high payload carrying rotorcraft relies on the capability to analyze and validate the structural integrity of the vehicle in addition to the rotor aerodynamic performance. The Mars Science Helicopter (MSH), a next generation hexacopter concept, is one example of a proposed vehicle that would perform science independently of a land-based vehicle. To ensure the feasibility and viability of MSH mission performance, it is critical to mature the structural design for these vehicle concepts to bridge the gap between the best practices of the spacecraft and aircraft communities. MSH was analyzed under operational and 26G quasi-static launch loads with different rotor arm and fuselage designs. Structural analysis results showed that rotor arms could be stiffened for significantly improved structural performance with minimal mass penalty, while the rotorcraft frame exhibited a more complex relationship between mass and launch load stresses due to the mass-dependent launch loads.

Load-Bearing↗

NASA NTRS2025

Structural Analysis of Load-Bearing Components in Mars Science Helicopter

The successful demonstration of powered flight on Mars by Ingenuity has led to the development of next generation Martian rotorcraft. As technology advances from a technology demonstrator to possible expanded planetary science investigations, the potential to fly a high payload carrying rotorcraft relies on the capability to analyze and validate the structural integrity of the vehicle in addition to the rotor aerodynamic performance. The Mars Science Helicopter (MSH), a next generation hexacopter concept, is an example of a proposed vehicle that would perform science investigations independent of a land-based vehicle. To ensure the feasibility and viability of MSH mission performance, it is critical to mature the structural design of vehicle concepts to bridge the gap between the best practices of the spacecraft and aircraft communities. MSH was analyzed under operational and 26G quasi-static launch loads with different rotor arm and frame designs. Structural analysis results showed that rotor arms could be stiffened for significantly improved structural performance with minimal mass penalty, while the rotorcraft frame exhibited a more complex relationship between mass and launch load stresses due to the mass-dependent launch loads.

Vehicle↗

NASA NTRS2019

Performance Optimization of Plate Airfoils for Martian Rotor Applications Using a Genetic Algorithm

The Mars Helicopter Technology Demonstrator will be flying on the NASA Mars 2020 rover mission scheduled to launch in July of 2020. The goal is to demonstrate the viability and potential of heavier-than-air vehicles in the Martian atmosphere. Research is performed at the Jet Propulsion Laboratory and NASA Ames Research Center to extend these capabilities and develop the Mars Science Helicopter as the next possible step for Martian rotorcraft. The Mars Science Helicopter mass is scaled up to the 5 to 20 kg range, allowing a greater payload (approximately 0.5 to 2.0 kg), and greater range (approximately 3 km). Key to achieving these targets is careful aerodynamic rotor design. The Martian atmosphere’s low density and the small helicopter rotors result in very low chord-based Reynolds number flows, which reduces rotor performance. A continuous genetic algorithm is developed to optimize airfoil shapes at representative conditions for the Martian atmosphere. Previous research indicates that sharp leading edges and plate-like airfoils can out-perform conventional airfoil shapes. The present optimization allows for camber and thickness variation of curved and polygonal thin airfoils with sharp leading edges. The airfoil performance is evaluated at the highest attainable liftto- drag ratio near a moderate lift coefficient at compressible Mach numbers, as expected for Martian rotor application. Increases between 16% and 29% in airfoil lift-to-drag ratio at fixed lift coefficients are observed when compared with the Mars Helicopter Technology Demonstrator airfoils. Improvements in hover figure of merit are estimated to be between 4% and 10%, when applied to the Mars Helicopter Technology Demonstrator.

Koning, Witold J. F.↗

NASA NTRS1999

Predicted Aerodynamic Characteristics of a NACA 0015 Airfoil Having a 25% Integral-Type Trailing Edge Flap

Using the two-dimensional ARC2D Navier-Stokes flow solver analyses were conducted to predict the sectional aerodynamic characteristics of the flapped NACA-0015 airfoil section. To facilitate the analyses and the generation of the computational grids, the airfoil with the deflected trailing edge flap was treated as a single element airfoil with no allowance for a gap between the flap's leading edge and the base of the forward portion of the airfoil. Generation of the O-type computational grids was accomplished using the HYGRID hyperbolic grid generation program. Results were obtained for a wide range of Mach numbers, angles of attack and flap deflections. The predicted sectional lift, drag and pitching moment values for the airfoil were then cast in tabular format (C81) to be used in lifting-line helicopter rotor aerodynamic performance calculations. Similar were also generated for the flap. Mathematical expressions providing the variation of the sectional lift and pitching moment coefficients for the airfoil and for the flap as a function of flap chord length and flap deflection angle were derived within the context of thin airfoil theory. The airfoil's sectional drag coefficient were derived using the ARC2D drag predictions for equivalent two dimensional flow conditions.

Hassan, Ahmed↗

NASA NTRSDate not supplied

Medium-Fidelity CFD Modeling of Multicopter Wakes for Airborne Sensor Measurements

A steady-state multicopter simulation capability leveraging automated Cartesian grid generation and a blade element source term rotor model was used to investigate multi-rotor aerodynamics in and out of ground effect. Simulations demonstrated that this model is able to predict reasonably accurate thrust in ground effect for both single and multiple propeller cases. The method yielded accurate lift and drag predictions for a commercial quadcopter when compared to recent wind tunnel test data. This aircraft was then simulated in a variety of flight conditions, including both hover and edgewise forward flight, to determine if generalized guidelines for airborne sensor placement could be developed. Velocity perturbation magnitudes showed large regions of affected air upstream of the vehicle at low speeds, which contracted as the vehicle’s speed was increased. Placing the sensors more than one characteristic length ahead of or above the aircraft reduces errors from rotor-induced flow at higher speeds. For low-speed forward flight, the entrainment of flow into the propeller wakes introduces significant flow turning above the aircraft, suggesting that a forward location, with more moderate perturbations, could be advantageous for these conditions.

ARMD↗

DOE OSTI2023

Holistic scan optimization of nacelle-mounted lidars for inflow and wake characterization at the RAAW and AWAKEN field campaigns

In this article, we provide a methodological framework for designing the scanning strategies of nacelle-mounted scanning lidars for wind energy field experiments, and apply it at two major experimental field campaigns. For the Rotor Aerodynamics, Aeroelastics, and Wake project (RAAW), we leverage two scanning lidars on one turbine to characterize the incoming turbulence and the turbine wake. For the American WAKE experimeNt (AWAKEN), we use four scanning lidars on top of four turbines in a large wind power plant to investigate both individual wakes and wind-plant-scale flow features.

17 WIND ENERGY↗

DOE OSTI2022

RAFT (Response Amplitudes of Floating Turbines) [SWR-22-40]

RAFT is a Python code for frequency-domain analysis of floating wind turbines. RAFT works in the frequency domain to provide efficient computations of a floating wind system's response spectra accounting for platform hydrodynamics, quasi-static mooring reactions, rotor aerodynamics, and linearized control. It can be used to calculate response amplitude operators (RAO's), power spectral densities, mean/static properties, and response metrics based on mean and root-mean-square values of each output. RAFT serves as the Level 1 model in the WEIS (Wind Energy with Integrated Servo-control) toolkit, and features an OpenMDAO wrapper.

Hall, Matthew↗

DOE OSTI2023

RAAW

High-fidelity wind turbine modeling advances necessitate model validation datasets of equally high fidelity. The Rotor Aerodynamics, Aeroelastics & Wake (RAAW) project was designed to address this need. This three-year project runs from October 2021 through October 2024 starting with a field data collection period followed by model validation activities. RAAW is a partnership between GE Renewable Energy and the United States Department of Energy (DOE) through the National Renewable Energy Laboratory (NREL) and Sandia National Laboratories. The field experiment is designed to make detailed measurements of the inflow, wind turbine response, and the resulting wake. The experimental dataset will be suitable for validating wind turbine models across the fidelity spectrum from actuator disk methods to blade-resolved codes.

17 WIND ENERGY↗

NASA NTRS1971

Investigation of rotor blade tip-vortex aerodynamics

Several aspects of the aerodynamics of rotor blade tip vortices are examined. Two particular categories are dealt with; (1) dynamic loads on a blade passing close to or intersecting a trailing vortex, and (2) the response of the trailing vortex core to changes in the flow. Results for both categories are in reasonable agreement with existing data, although lower pressure gradients were obtained than anticipated for category one. A correlation between trailing edge sweep angle at the tip and vortex core size was noted for category two.

Lewellen, W. S.↗

NASA NTRS1976

Correlation of full-scale helicopter rotor performance in air with model-scale Freon data

An investigation was conducted in a transonic dynamics tunnel to measure the performance of a 1/5 scale model helicopter rotor in a Freon atmosphere. Comparisons were made between these data and full scale data obtained in air. Both the model and full scale tests were conducted at advance ratios between 0.30 and 0.40 and advancing tip Mach numbers between 0.79 and 0.95. Results show that correlation of model scale rotor performance data obtained in Freon with full scale rotor performance data in air is good with regard to data trends. Mach number effects were found to be essentially the same for the model rotor performance data obtained in Freon and the full scale rotor performance data obtained in air. It was determined that Reynolds number effects may be of the same magnitude or smaller than rotor solidity effects or blade elastic modeling in rotor aerodynamic performance testing.

Yeager, W. T., Jr.↗

NASA NTRS1976

A mathematical simulation model of a 1985-era tilt-rotor passenger aircraft

A mathematical model for use in real-time piloted simulation of a 1985-era tilt rotor passenger aircraft is presented. The model comprises the basic six degrees-of-freedom equations of motion, and a large angle of attack representation of the airframe and rotor aerodynamics, together with equations and functions used to model turbine engine performance, aircraft control system and stability augmentation system. A complete derivation of the primary equations is given together with a description of the modeling techniques used. Data for the model is included in an appendix.

Mcveigh, M. A.↗

NASA NTRS1981

Performance of wind turbines in a turbulent atmosphere

The effect of atmospheric turbulence on the power fluctuations of large wind turbines was studied. The significance of spatial non-uniformities of the wind is emphasized. The turbulent wind with correlation in time and space is simulated on the computer by Shinozukas method. The wind turbulence is modelled according to the Davenport spectrum with an exponential spatial correlation function. The rotor aerodynamics is modelled by simple blade element theory. Comparison of the spectrum of power output signal between 1-D and 3-D turbulence, shows the significant power fluctuations centered around the blade passage frequency.

Sundar, R. M.↗

NASA NTRS1984

Acoustic prediction methods for the NASA generalized advanced propeller analysis system (GAPAS)

Classical methods of propeller performance analysis are coupled with state-of-the-art Aircraft Noise Prediction Program (ANOPP:) techniques to yield a versatile design tool, the NASA Generalized Advanced Propeller Analysis System (GAPAS) for the novel quiet and efficient propellers. ANOPP is a collection of modular specialized programs. GAPAS as a whole addresses blade geometry and aerodynamics, rotor performance and loading, and subsonic propeller noise.

Padula, S. L.↗