Search NASA⌕ Search

SEARCH · Search NASA

Results for “SEAPLANES - IMPACT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1933

A Complete Tank Test of a Model of Flying-boat Hull - N.A.C.A. Model 16

A model of a 2-step flying-boat hull, of the type generally used in England, was tested according to the complete method described in the N.A.C.A. Technical Note No. 464. The lines of this model were taken from offsets given by Mr. William Munro in Flight, May 29, 1931. The data cover the range of loads, speeds, and trim angles that may be of use in applying the hull form to the design of any seaplane. The results are reduced to nondimensional form to aid application to design problems and facilitate comparison with the performance of other hulls. The water characteristics of Model 16 are compared with those of Model 11-A, which is representative of current American practice. The results show that when the two forms are applied to a given seaplane design under optimum conditions for each, the performance of Model 16 will be somewhat inferior to that of Model 11-A.

Shoemaker, James H↗
NASA NTRS1933

A complete tank test of a model of a flying-boat hull-N.A.C.A. Model No.11

This note discusses the limitations of the conventional tank test of a seaplane model. The advantages of a complete test, giving the characteristics of the model at all speeds, loads, and trim angles in the useful range are pointed out. The data on N.A.C.A. Model No.11, obtained from a complete test, are presented and discussed. The results are analyzed to determine the best trim angle for each speed and load. The data for the best angles are reduced to non-dimensional form for ease of comparison and application. A practical problem using the characteristics of model no.11 is presented to show the method of calculating the take-off time and run of a seaplane from these data.

Shoemaker, James M↗
NASA NTRS1927

Tests on airplane fuselages, floats and hulls

This report is a compilation of test data on airplane fuselages, nacelles, airship cars, seaplane floats, and seaplane hulls, prepared by the Bureau of Aeronautics, at the requests of the National Advisory Committee for Aeronautics. The discussion of the data includes the derivation of a scale correction curve to be used in obtaining the full scale drag. Composite curves of drag and L/D for floats and hulls are also given. (author)

Diehl, Walter S↗
NASA NTRS1933

A Complete Tank Test of a Model of a Flying-Boat Hull - N.A.C.A. Model No.11

This note discusses the limitations of the conventional tank test of a seaplane model. The advantages of a complete test, giving the characteristics of the model at all speeds, loads, and trim angles in the useful range are pointed out. The data on N.A.C.A. Model No.11, obtained from a complete test, are presented and discussed. The results are analyzed to determine the best trim angle for each speed and load. The data for the best angles are reduced to non-dimensional form for ease of comparison and application. A practical problem using the characteristics of model no.11 is presented to show the method of calculating the take-off time and run of a seaplane from these data.

Shoemaker, James M.↗
NASA NTRS1950

Hydrodynamic Properties of Planing Surfaces and Flying Boats

The study of the hydrodynamic properties of planing bottom of flying boats and seaplane floats is at the present time based exclusively on the curves of towing tests conducted in tanks. In order to provide a rational basis for the test procedure in tanks and practical design data, a theoretical study must be made of the flow at the step and relations derived that show not only qualitatively but quantitatively the inter-relations of the various factors involved. The general solution of the problem of the development of hydrodynamic forces during the motion of the seaplane float or flying boat is very difficult for it is necessary to give a three-dimensional solution, which does not always permit reducing the analysis to the form of workable computation formulas. On the other had, the problem is complicated by the fact that the object of the analysis is concerned with two fluid mediums, namely, air and water, which have a surface of density discontinuity between them. The theoretical and experimental investigations on the hydrodynamics of a ship cannot be completely carried over to the design of floats and flying-boat hulls, because of the difference in the shape of the contour lines of the bodies, and, because of the entirely different flow conditions from the hydrodynamic viewpoint.

Sokolov, N. A.↗
NASA NTRS1949

Systematic model researches on the stability limits of the DVL series of float designs

To determine the trim range in which a seaplane can take off without porpoising, stability tests were made of a Plexiglas model, composed of float, wing, and tailplane, which corresponded to a full-size research airplane. The model and full-size stability limits are in good agreement. After all structural parts pertaining to the air frame were removed gradually, the aerodynamic forces replaced by weight forces, and the moment of inertia and position of the center of gravity changed, no marked change of limits of the stable zone was noticeable. The latter, therefore, is for practical purposes affected only by hydrodynamic phenomena. The stability limits of the DVL family of floats were determined by a systematic investigation independent of any particular sea-plane design, thus a seaplane may be designed to give a run free from porpoising.

Sottorf, W.↗
NASA NTRS1927

The "Dornier Mercury" commercial airplane with B.M.W. VI 600 HP. engine

The Dornier Mercury (Merkur) is an outgrowth of the Dornier Komet. It is designed as a passenger aircraft with the Alpine routes in mind. Its fuselage is made of steel for high stressed parts and duraluminum for all others. It can also be outfitted as a seaplane.

AIRPLANES - DORNIER MERKUR (GER )↗
NASA NTRS1945

An Investigation of the Ranger V-770-8 Engine Installation for the Edo XOSE-1 Airplane II : Aerodynamics

Investigations were made to determine the cowling and cooling characteristics of the Ranger V-770-8 engine installation in an observation seaplane. Final cowl configurations possessed ample engine and oil-cooler pressure drops for cooling in the critical normal-power climb condition with any of the three baffle configurations tested. The indicated critical Mach number of the cowling was found to be 0.70 as determined by the pressure on the lower lip of the inlet.

ENGINE COWLINGS-RANGER↗
NASA NTRS1922

Comparative performance with direct and geared engines

Comprehensive tests were made to compare the performance of the F-5-L Boat Seaplane fitted with direct drive and Liberty engines. Details are given on the test conditions. The conclusions of the comparison tests follow. 1) An F-5-L with geared engines takes off in approximately 90 percent of the time required for the same airplane with standard direct drive engines. An F-5-L with geared engines climbs in 20 minutes to an altitude approximately 20 percent greater than that obtained with the standard direct drive on the same airplane. 3) There is a large difference between the climbs of the two airplanes of the same type. This difference will always be more pronounced when the climb is normally slow. In the case of the F-5-L airplanes under construction, it is of the order of a 10 percent difference in altitude on a 20 minute climb. 4) The maximum speed of an F-5-L with geared engines is about 3.5 percent greater than the maximum speed of the same airplane with standard direct drive engines (at the same engine r.p.m.). 5) The fuel consumption is probably less effected by the type of drive than by inherent differences in the performance of different airplanes.

Diehl, W S↗
NASA NTRS1928

The reaction on a float bottom when making contact with water at high speeds

Tests were conducted to investigate the possibility of a serious accident arising from unintentional contact with the water in substantially horizontal flight at high speed. Referring to vector diagrams on Figure 2, it will be seen that a very dangerous condition may arise if the float be allowed to come in contact with the water at high speeds as, for example, when flying at high speed just above the water. The initial diving moment due to suction and drag combined may be great enough to cause the seaplane to nose under before the pilot is able to control the motion. The same test data indicate clearly the existence of forces and moments tending to produce the phenomenon observed by Mr. Carroll (Technical Note No. 287) when the maneuver is carried out at lower speeds, as in a landing.

Richardson, H C↗
NASA NTRS1934

Tank tests of flat and v-bottom planning surfaces

Four planing surfaces, all having beams of 16 inches and lengths of 60 inches but varying in dead rise by 10 degrees increments from 0 degrees to 30 degrees, were tested in the N.A.C.A. tank. The results cover a wide range of speed, loads, and trim angles, and are applicable to a variety of problems encountered in the design of seaplanes. The data are analyzed to determine the characteristics of each surface at the trim angle giving minimum resistance for all the speed and loads tested. A planing coefficient intended to facilitate the application of the results to design work is developed and curves of resistance, wetted length, and center of pressure are plotted against this coefficient. Several examples, showing the application of the test data to specific design problems are included.

Shoemaker, James M↗
NASA NTRS1934

The effect of trim angle on the take-off performance

Data obtained at the N.A.C.A. tank from tests on the models of three flying-boat hulls - N.A.C.A. models 11-A, 16, and 22 - are used to demonstrate the effect of trim angle on water resistance. A specific example is taken, and data from Model 11-A are used to show that the trim angle giving the minimum water resistance will give minimum total air-plus-water resistance. Total-resistance curves for best trimmed angles and other angles are compared for the same example. The effect of wind on best trim angles and upon the take-off and run is shown by the working of an example. The possibility of using tank data on trim angles as aid in piloting is discussed, and an instrument for use in determining the trim angle of seaplanes is described. The importance of maintaining the best trim angle throughout the take-off is indicated.

Shoemaker, James M↗
NASA NTRS1938

The Increase in Frictional Resistance Caused by Various Types of Rivet Heads as Determined by Tests of Planing Surfaces

The increase in the frictional resistance of a surface caused by the presence of rivet heads was determined by towing four planing surfaces of the same dimensions. One surface was smooth and represented a surface without rivet heads or one with perfectly flush countersunk rivets. The other three surfaces were each fitted with the same number of full-size rivet heads but of a different type arranged in the same pattern on each surface. The surfaces were towed at speeds representative of the high water speeds encountered by seaplanes during take-off and the range of Reynolds Number covered by the test was from 4 x 10(exp 6) to 18 x 10(exp 6). The rivet heads investigated were oval countersunk, brazier, and round for rivets having shanks 5/32 inch in diameter. The oval countersunk heads were sunk below the surface by dimpling the plating around them. The results of the tests showed that, for the rivet heads investigated, the increase in the friction coefficient of the surface is directly proportional to the height of the rivet head. The order of merit in regard to low resistance is flush countersunk, oval countersunk (whether sunk below the surface or not), brazier, and round.

Truscott, Starr↗
NASA NTRS1938

The Aerodynamic Drag of Five Models of Side Floats N.A.C.A. Models 51-E, 51-F, 51-G, 51-H, 51-J

The drag of five models of side floats was measured in the N.A.C.A. 7- by 10-foot wind tunnel. The most promising method of reducing the drag of floats indicated by these tests is lowering the angle at which the floats are rigged. The addition of a step to a float does not always increase the drag in the flying range, floats with steps sometimes having lower drag than similar floats without steps. Making the bow chine no higher than necessary might result in a reduction in air drag because of the lower angle of pitch of the chines. Since side floats are used formally to obtain lateral stability when the seaplane is operating on the water at slow speeds or at rest, greater consideration can be given to factors affecting aerodynamic drag than is possible for other types of floats and hulls.

House, R O↗
NASA NTRS1923

On the stability of oscillations of an airplane wing

During a flight with a Van Berkel W. B. seaplane it was observed that the wing could perform violent oscillations. A theoretical and experimental investigation led to the conclusion, that in some cases an unstable oscillation of the wing-aileron system under the influence of the elastic and aerodynamic forces is possible without further external causes.

FLUTTER - WINGS - VAN BERKEL W B↗