Search NASA⌕ Search

SEARCH · Search NASA

Results for “SHEAR STRAIN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

An instrumented fastener for shear force measurements in joints

A preliminary investigation has been conducted on instrumented fasteners for use as sensors to measure the shear loads transmitted by individual fasteners installed in double-splice joints. Calibration and load verification tests were conducted for instrumented fasteners installed at three fastener torque levels. Results from calibration tests show that the shear strains obtained from the instrumented fasteners vary linearly with the applied load and that the instrumented fasteners can be effectively used to measure shear loads transmitted by individual fasteners installed in double-splice joints. Tests were also conducted with three instumented fasteners installed in a typical double-splice joint. The test results showed that the load distribution between individual fasteners is dependent on the location of the fastener in the joint and the fastener torque level.

Sawyer, J. W.↗
NASA NTRS1994

Use of photostress to analyze behavior of an aft skirt test specimen

Strains at twenty-one selected points in the critical lower weld region of a aft skirt of a solid rocket booster of the shuttle were measured using photoelastic coatings and stress separator gages. Data were taken at loads of 5, 14, 20, 28, 42, 56, and 70 percent of the design limit load. Results indicate that general yielding occurred in the weld metal and for a short distance outside the fusion boundaries on either side of the weld metal. The fusion boundaries did not yield at the 70 percent load. Slight non-linearity in the load strain curves were observed at several points above the 20 percent load level. Maximum measured strains occurred at points in the forged metal of the holddown post along a line 0.50 inches from the centerline of the weld. Maximum shearing strains within the area covered by the photoelastic coating occurred at points approximately 0.33 inches to the right of the weld centerline near points 6 and 7 and lying along a yellow vertical line extending from just below point 6 to point 11. Photoelastic coatings were shown to be an excellent method to provide the whole field strain distribution in the region of the critical weld and to enhance the overall understanding of the behavior of the welded joint.

Gambrell, S. C., Jr.↗
NASA NTRS2003

Behavior of Three Metallic Alloys under Combined Axial-Shear Stresses at Elevated Temperature

Type 316 stainless steel, Haynes 188, and Inconel 718 samples were subjected to an axial-shear strain controlled loading history while the specimen temperature was held at 650 C to quantify the evolution of material state under a complex biaxial load path when the material is in the viscoplastic domain. Yield surfaces were constructed in the axial-shear stress plane using a sensitive, 30 x 10(exp -6)m/m, equivalent offset strain definition for the yield strain. Subsequent yield surfaces were constructed at various points along the strain path to define the material evolution. These subsequent yield surface translated, expanded, and distorted relative to the initial yield surface. Each of these very different materials exhibited components of isotropic, kinematic and distortional hardening. Furthermore, subsequent yield surfaces for each material have a very well defined front face and a poorly defined, flattened, back side.

Colaiuta, J. F.↗
DOE OSTI2020

Plate motion in sheared granular fault system

Plate motion near the fault gouge layer, and the elastic interplay between the gouge layer and the plate under stick-slip conditions, is key to understanding the dynamics of sheared granular fault systems. Here, a two-dimensional implementation of the combined finite-discrete element method (FDEM), which merges the finite element method (FEM) and the discrete element method (DEM), is used to explicitly simulate a sheared granular gouge fault system. In this work we focus on investigating the influence of normal load, driving shear velocity and plate stiffness on the velocities and displacements in the direction parallel to the shear direction (x-direction) measured at locations on the upper and lower plates just adjacent to the gouge. The simulations show that during slip phases the magnitudes of the measured velocities on the upper and lower plates are proportional to the normal load and may be inversely proportional to the square root of the plate's shear modulus. Whereas, the driving shear velocity does not show distinct influence on the measured velocities. Additionally, large slip velocities are generally associated with large macroscopic friction coefficient drops. For the models subjected to smaller normal loads, larger shear velocities and with stiffer shear plates, the same magnitude of slip velocity could cause a larger drop of macroscopic friction coefficient. During stick phases, the velocities of the upper and lower plates are respectively slightly greater and slightly smaller than half of the driving shear velocity and are both in the same direction of shear. The shear strain rate of the gouge is calculated from this velocity difference between the upper and lower plate during stick phases and thus the gouge effective shear modulus can be calculated. The results show that the gouge effective shear modulus increases proportionally with normal load, while the influence of shear velocity and plate stiffness on gouge effective shear modulus is minor. The simulations address the dynamics of a laboratory-scale fault gouge system and may aid in revealing the complexities of earthquake frictional dynamics.

58 GEOSCIENCES↗
NASA NTRS1988

Combined mechanical loading of composite tubes

An analytical/experimental investigation was performed to study the effect of material nonlinearities on the response of composite tubes subjected to combined axial and torsional loading. The effect of residual stresses on subsequent mechanical response was included in the investigation. Experiments were performed on P75/934 graphite-epoxy tubes with a stacking sequence of (15/0/ + or - 10/0/ -15), using pure torsion and combined axial/torsional loading. In the presence of residual stresses, the analytical model predicted a reduction in the initial shear modulus. Experimentally, coupling between axial loading and shear strain was observed in laminated tubes under combined loading. The phenomenon was predicted by the nonlinear analytical model. The experimentally observed linear limit of the global shear response was found to correspond to the analytically predicted first ply failure. Further, the failure of the tubes was found to be path dependent above a critical load level.

Derstine, Mark S.↗
NASA NTRS1989

Assumed strain distributions for a finite strip plate bending element using Mindlin-Reissner plate theory

A linear finite strip plate element based on Mindlin-Reissner plate theory is developed. The analysis is suitable for both thin and thick plates. In the formulation, new transverse shear strains are introduced and assumed constant in each two-node linear strip. The element stiffness matrix is explicitly formulated for efficient computation and computer implementation. Numerical results showing the efficiency and predictive capability of the element for the analysis of plates are presented for different support and loading conditions and a wide range of thicknesses. No sign of shear locking is observed with the newly developed element.

Chulya, Abhisak↗
NASA NTRS2013

Empirical Study of the Multiaxial, Thermomechanical Behavior of NiTiHf Shape Memory Alloys

An empirical study was conducted to characterize the multiaxial, thermomechanical responses of new high temperature NiTiHf alloys. The experimentation included loading thin walled tube Ni(sub 50.3)Ti(sub 29.7)Hf(sub 20) alloy samples along both proportional and nonproportional axial-torsion paths at different temperatures while measuring surface strains using stereo digital image correlation. A Ni(sub 50.3)Ti(sub 33.7)Hf(sub 16) alloy was also studied in tension and compression to document the effect of slightly depleting the Hf content on the constitutive responses of NiTiHf alloys. Samples of both alloys were made from nearly texture free polycrystalline material processed by hot extrusion. Analysis of the data shows that very small changes in composition significantly alter NiTiHf alloy properties, as the austenite finish (Af) temperature of the 16-at Hf alloy was found to be approximately 60 C less than the 20-at Hf alloy (approximately 120 C vs. 180 C). In addition, the 16-at Hf alloy exhibited smaller compressive transformation strains (2 vs. 2.5 percent). Multi-axial characterization of the 20-at % Hf alloy showed that while the random polycrystal transformation strains in tension (4 percent) and compression (2.5 percent) are modest in comparison with binary NiTi (6 percent, 4 percent), the torsion performance is superior (7 vs. 4 shear strain width to the pseudoelastic plateau).

tensile deformation↗
NASA NTRS1992

Coupled elastic response of open section laminated composite beams subject to generalized beam loading

A generalized beam theory for arbitrary open section laminated composite beams subjected to generalized beam loading is developed using a strength of materials approach. At present, the theory is limited to statistically determinate beams. Solution of the general system of equations yields strain and curvature distributions as functions of the axial coordinate x and the contour coordinate s. Average stresses on a given cross section or ply stresses in a local coordinate system are determined using these distributions. Data obtained for thin-walled open section composite beams reveal that elastic coupling occurs among curvatures, shearing strains, and axial strain, depending on the laminate stiffness parameters. Laminate ply layup does not affect the location of the shear center in the thin-wall approximation, but may have a significant impact for thicker walled open sections. The average axial stress distribution is found to be distinctly different from the isotropic distribution, but the average shear stress distribution is the same as that in the isotropic case.

Zvarick, Albert G.↗
DOE OSTI2023

Ab initio study of mechanical and thermal properties of GeTe-based and PbSe-based high-entropy chalcogenides

GeTe-based and PbSe-based high-entropy compounds have outstanding thermoelectric (TE) performance and crucial applications in mid and high temperatures. Recently, the optimization of TE performance of high-entropy compounds has been focused on reducing thermal conductivity by strengthening the phonon scattering process to improve TE performance. We report a first-principles investigation on nine GeTe-based high-entropy chalcogenide solid solutions constituted of eight metallic elements (Ag, Pb, Sb, Bi, Cu, Cd, Mn, and Sn) and 13 PbSe-based high-entropy chalcogenide solid solutions: Pb 0.99-y Sb 0.012 Sn y Se 1-2x Te x S x (x = 0.1, 0.2, 0.25, 0.3, 0.35, 0.4, 0.45, and y = 0) and Pb 0.99-y Sb 0.012 Sn y Se 1-2x Te x S x (y = 0.05, 0.1, 0.15, 0.2, 0.25 and x = 0.25). We have investigated the mechanical properties focusing on Debye temperature (Θ D ), thermal conductivity (κ), Grüneisen parameter (γ α ), dominant phonon wavelength (λ dom ), and melting temperature (T m ). We find that the lattice thermal conductivity is significantly reduced when GeTe is alloyed into the following compositions: Ge 0.75 Sb 0.13 Pb 0.12 Te, Ge 0.61 Ag 0.11 Sb 0.13 Pb 0.12 Bi 0.01 Te, and Ge 0.61 Ag 0.11 Sb 0.13 Pb 0.12 Mn 0.05 Bi 0.01 Te. This reduction is due to the mass increase and strain fluctuations. The results also show that Ge 0.61 Ag 0.11 Sb 0.13 Pb 0.12 Bi 0.01 Te solid solution has the lowest Young’s modulus (30.362 GPa), bulk and shear moduli (18.626 and 12.359 GPa), average sound velocity (1653.128 m/sec), Debye temperature (151.689 K), lattice thermal conductivity (0.574 W.m –1 .K –1 ), dominant phonon wavelength (0.692 Å), and melting temperature (535.91 K). Moreover, Ge 0.61 Ag 0.11 Sb 0.13 Pb 0.12 Bi 0.01 Te has the highest Grüneisen parameter with a reduced and temperature-independent lattice thermal conductivity. The positive correlation between Θ D and κ is revealed. Alloying of PbSe-based high-entropy by Sb, Sn, Te, and S atoms at the Se and Pb sites resulted in much higher shear strains resulted in the reduction of phonon velocity, a reduced Θ D , and a lower lattice thermal conductivity.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2021

American eel resilience to simulated fluid shear associated with passage through hydroelectric turbines

American eel (Anguilla rostrata) populations have declined within their native range along the eastern coast of North America due to factors such as commercial fishing, habitat alteration, and dams. American eel are catadromous fish species, and high mortality rates (>40%) have been observed for freshwater life-stage adult eel passing downstream through hydropower turbines. Lacerations and sectioning of fish have been observed downstream of turbines and these injuries are commonly associated with direct contact with the turbine runner, whether through blade strike or pinching and grinding. Exposure to fluid shear may also be a source of injury, however, little is known about American eel susceptibility to this physical stressor. Eels are considerably flexible when compared to other fish species and lack other morphological characteristics that would make them susceptible to fluid shear, such as protruding eyes, large scales, and large operculum. European eel, which have previously been tested for susceptibility to fluid shear, were found to be resilient. To determine if American eel are also resilient to fluid shear, forty American eel were exposed to a water jet, simulating severe fluid shear (strain rate > 800 s –1 ) that fish may experience when passing downstream through turbines. No immediate or delayed (48 h) signs of injury were observed after exposure to severe fluid shear. Based on this study, and a previous study conducted on American eel susceptibility to barotrauma, the source of injury and mortality of American eel passing through turbines is likely attributed to blade strike or pinching and grinding.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1992

Vibration of thick composite laminates - Analytic theory and finite element approximations

Two versions of a (1,2) higher-order laminate plate theory are extended to elastodynamics, and their performance on free vibration problems for homogeneous and laminated plates is examined. Both versions are based on continuously varying through-the-thickness linear and parabolic distributions for the inplane and transverse displacements, respectively. They also use continuous parabolic distributions for the transverse shear strains. The theory is capable of providing an improved accuracy as compared to other approximate theories and accurately predicting the lowest thickness-stretch frequencies which cannot be obtained with shear-deformable theories. The theory is considered to be particularly well-suited for generating simple and efficient variationally-based displacement finite elements leading to C sup 0 elements with only five degrees of freedom per node.

Tessler, A.↗
NASA NTRS1987

In-situ thermal cycling in SEM of a graphite-aluminum composite

In situ SEM observations of a graphite-aluminum composite (unidirectional P100 graphite-fiber-reinforced 6061 aluminum MMC plates) were used to measure displacements within the graphite fiber relative to the interface between the graphite fiber and the aluminum matrix during thermal cycling. Specimens were thermally cycled from room temperature to 300 C or 500 C in a SEM chamber and then cooled to room temperature. The obtained shear strains within the fiber were then related to anomalous values of measured residual stresses and to the impact on the composite coefficient of expansion and potential damage under thermal fatigue loading. The shear mechanism was proposed as a source of temperature limits on the low coefficient of expansion of these composites, as well as a potential source of thermal fatigue degradation.

Cheong, Y. M.↗
DOE OSTI2021

Strongly Anisotropic Thermomechanical Response to Shock Wave Loading in Oriented Samples of the Triclinic Molecular Crystal 1,3,5-Triamino-2,4,6-trinitrobenzene

All-atom molecular dynamics (MD) simulations were used to study shock wave loading in oriented single crystals of the highly anisotropic triclinic molecular crystal 1,3,5-triamino-2,4,6-trinitrobenzene (TATB). The crystal structure consists of planar hydrogen-bonded sheets of individually planar TATB molecules that stack into graphitic-like layers. Shocks were studied for seven systematically prepared crystal orientations with limiting cases that correspond to shock propagation exactly perpendicular and exactly parallel to the graphitic-like layers. The simulations were performed for initially defect-free crystals using a reverse-ballistic configuration that generates explicit, supported shocks. Final longitudinal stress components are between ≈8.5 and ≈10.5 GPa for the 1.0 km s –1 impact speed studied. Orientation-dependent properties are reported including shock speeds, stresses, temperatures, compression ratios, and local material strain rates. Spatiotemporal maps of the temperature, stress tensor, material flow, and molecular orientations reveal complicated processes that arise for specific shock directions. Furthermore, the results indicate that TATB shock response is highly sensitive to crystal orientation, with significant qualitative differences for the time evolution of the stress tensor and temperature, elastic/inelastic compression response, defect formation and growth, critical von Mises stress, and strain rates during shock rise that span nearly an order of magnitude. A variety of inelastic deformation mechanisms are identified, ranging from crumpling of graphitic-like layers to dislocation-mediated plasticity to intense shear strain localization. To our knowledge, these are the first systematic MD simulations and analysis of explicit shock wave propagation along nontrivial crystal directions in a triclinic molecular crystal.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Symmetry mismatch controlled ferroelastic domain ordering and the functional properties of manganite films on cubic miscut substrates

We have studied the magnetotransport properties and strain release mechanisms in ferroelastic La 0.9 Sr 0.1 MnO 3 (LSMO) epitaxial thin films on SrTiO 3 (STO)(001) substrates with different miscut angles. The substrate miscut angle plays a critical role in releasing shear strain and has a huge impact on the properties of the films. The strain relaxes by monoclinic distortion for films on low miscut substrates and for higher miscut substrates, the strain relaxation causes the formation of periodic twin domains with larger periodicities. Furthermore, we observe that the Curie temperature (T C ) decreases systematically, and magnetoresistance (MR) increases with increasing the miscut angle. Such changes in the magnetic and transport properties could be due to the increased density of phase boundaries (PBs) with the increase of miscut angle. This work provides a way to tailor film microstructures and subsequent functional properties of other complex oxide films on miscut substrates with symmetry mismatch.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Mechanical, electronic, optical, piezoelectric and ferroic properties of strained graphene and other strained monolayers and multilayers: an update

Abstract This is an update of a previous review (Naumis et al 2017 Rep. Prog. Phys. 80 096501). Experimental and theoretical advances for straining graphene and other metallic, insulating, ferroelectric, ferroelastic, ferromagnetic and multiferroic 2D materials were considered. We surveyed (i) methods to induce valley and sublattice polarisation ( P ) in graphene, (ii) time-dependent strain and its impact on graphene’s electronic properties, (iii) the role of local and global strain on superconductivity and other highly correlated and/or topological phases of graphene, (iv) inducing polarisation P on hexagonal boron nitride monolayers via strain, (v) modifying the optoelectronic properties of transition metal dichalcogenide monolayers through strain, (vi) ferroic 2D materials with intrinsic elastic ( σ ), electric ( P ) and magnetic ( M ) polarisation under strain, as well as incipient 2D multiferroics and (vii) moiré bilayers exhibiting flat electronic bands and exotic quantum phase diagrams, and other bilayer or few-layer systems exhibiting ferroic orders tunable by rotations and shear strain. The update features the experimental realisations of a tunable two-dimensional Quantum Spin Hall effect in germanene, of elemental 2D ferroelectric bismuth, and 2D multiferroic NiI 2 . The document was structured for a discussion of effects taking place in monolayers first, followed by discussions concerning bilayers and few-layers, and it represents an up-to-date overview of exciting and newest developments on the fast-paced field of 2D materials.

Physics↗
NASA NTRS1984

A simple higher-order theory for laminated composite plates

A higher-order shear deformation theory of laminated composite plates is developed. The theory contains the same dependent unknowns as in the first-order shear deformation theory of Whitney and Pagano (1970), but accounts for parabolic distribution of the transverse shear strains through the thickness of the plate. Exact closed-form solutions of symmetric cross-ply laminates are obtained and the results are compared with three-dimensional elasticity solutions and first-order shear deformation theory solutions. The present theory predicts the deflections and stresses more accurately when compared to the first-order theory.

Reddy, J. N.↗
NASA NTRS1992

The influence of fiber waviness on the compressive behavior of unidirectional continuous fiber composites

The influence of fiber waviness and matrix nonlinearity on the compressive behavior of continuous fiber composites is studied. A micromechanics model based on the kinematics of the fibers has been developed to predict the behavior of unidirectional composites with initially wavy fibers under compressive loads. The initial waviness has been idealized as sinusoidal. Nonlinear shear behavior of the matrix has been included. Because the shear strain in the matrix is a function of position, the deformed shape of the fibers differs from the initial shape. Therefore, the deformed fiber shape is represented by a sine series. Fiber waviness and matrix shear properties have been determined experimentally for T650-42/Radel C under several conditions. These experimental data have been used as input into the analytical model. Predicted compressive response is in reasonable agreement with experimental data.

Highsmith, Alton L.↗