Results for “SLURRY” — Page 7

DOE OSTI2020

Mechanisms influencing and prediction of tool influence function spots during hemispherical sub-aperture tool polishing on fused silica

Sub-aperture tool polishing of precision optics requires a detailed understanding of the local material removal [tool influence function (TIF)] at the contact spot between the workpiece and tool to achieve high removal determinism and hence precision of the optic relative to the desired/design surface figure. In this study, the mechanisms influencing and the quantitative prediction of the removal rate and shape of TIF spots during polishing of fused silica glass with cerium oxide slurry using a rotating hemispherical pad-foam tool for a wide variety of process conditions (including tool properties, kinematics, and applied displacements) are investigated. The TIF volumetric removal rate can be estimated utilizing the average relative velocity and contact area using a simple analytical model. In addition, stability of the volumetric removal rate for fixed process conditions is shown to be greatly dependent on the pad preparation and amount of tool use (affecting both pad topography and slurry buildup), whose general behavior shows an increase in removal rate followed by stabilization with polishing time. The determination of the TIF removal shape is more complex. An extended version of the Preston removal model is developed to explain a comprehensive set of measured TIF removal shapes to within ∼ <#comment/> 22 % <#comment/> . This model incorporates a number of phenomena impacting the TIF removal shape including: (a) temporal and spatial dependent relative velocity between the workpiece and tool; (b) an elastic mechanics based, as well as hydrodynamic, pressure distribution; (c) a spatially dependent friction coefficient possibly caused by both reduced slurry replenishment in low velocity regions and pad slurry islands (100 µm scale) and porosity (millimeter scale); and (d) a shear-based removal mechanism on the periphery of the contact spot.

Suratwala, T. (ORCID:0000000190861039)↗

DOE OSTI2021

Cost-effective, Thin-film SOFCs for Reliable Power Generation (Final Report)

The project was aimed at developing and demonstrating an advanced solid-oxide fuel cell (SOFC) technology to cost-effectively and reliably generate electricity directly from hydrocarbon fuels (e.g., natural gas and coal-derived syngas) for distributed and central generation applications. The studied technology was built on a planar, porous metal-supported SOFC (MS-SOFC) with a unique thin-film structure having its anode intimately supported on a metal substrate. The porous metal support with graded porosity was fabricated from a low-cost scalable phase-inversion tape casting method. Anode, thin-film electrolyte, and cathode were sequentially deposited on the porous metal substrate using atmospheric plasma spray (APS). In this study, it was shown that the composition of the casting slurry could significantly influence the morphology of the metal support fabricated using the phase-inversion tape-casting method. Increasing the solid loading in the slurry favored the formation and growth of finger-like pores to a point, but the presence of excessive solid loading increased the viscosity of the casting slurry, restraining the growth of finger-like pores. With the increase in the amount of the binder polyethersulfone (PESf) in the slurry, well grown finger-like pores and a thin sponge-like layer were formed. Since the parameters of the APS process have a significant effect on the microstructure of coatings, which in turn affects or determines the SOFC cell performance, a series of metal-supported solid oxide fuel cells with a four-layer cell configuration of 430L/Ni-ScSZ/ScSZ/LSCF have been fabricated by a combination of phase inversion tape casting and APS techniques. Electrochemical testing of the cells fabricated from different deposition APS conditions revealed significant differences in cell performance.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2020

Characterizing Impacts of Dry Coal Feeding in High Pressure Oxy-Coal Combustion Systems

Reaction Engineering International (REI) has managed a team of experts from the University of Utah, Southeast University (SEU) in Nanjing, China, Electric Power Research Institute (EPRI), Corrosion Management Ltd. (C-M), Praxair, and Brigham Young University (BYU) to investigate dry pulverized coal feeding for pressurized oxy-coal combustion. Dry feed firing systems for entrained flow, pressurized, oxy-coal combustors have not been well developed, although related technologies have been used in the Shell Gasification Process and for pressurized fluid bed combustion. DOE-funded research recently completed at REI and the University of Utah focused on characterizing impacts of high temperatures and pressures in oxy-coal combustion systems. For high pressure combustion, that research used a coal slurry feed into a 17 bar pressurized combustor. As a consequence of that research, it was identified that fuel feeding and firing system flexibility are challenges that require attention. Based on that experience, the approach of using a coal slurry feed system leads to challenges in producing consistent atomization of the slurry, which causes burnout problems, especially at high pressures. In addition, slurry atomization processes may be difficult to scale to sizes appropriate for practical commercial use. Dry pressurized coal burner systems, on the other hand, have the potential to yield efficiency gains, improve flexibility and facilitate applications at larger scales. Experimental work was conducted at the University of Utah Industrial Combustion and Gasification Research Facility as well as the 100 kW pressurized oxy-coal combustor (POC) facility at Brigham Young University. Mechanism development and CFD-based combustion and dense-phase flow modeling were performed at REI. Successful completion of the project objectives has resulted in the following key deliverables: 1) Design and prototype of a pressurized pulverized coal feeding and oxy-firing system 2) Data from a 100kW, pressurized (15 bar) entrained flow reactor with a dry feeding delivery and burner system that describes flame characteristics, radiative heat flux profiles, carbon burnout, along with characteristics of ash aerosols, fouling, and slagging. 3) Validated and transportable models that describe the relevant conditions in pressurized oxy-combustion systems and that can be used for scale-up and optimization. 4) Principles to guide design of high pressure, pilot-scale and full-scale coal oxy-firing systems. 5) Assessment of pressurized oxy-combustion impacts on key parameters relevant to oxy-coal fired utility boilers such as coal devolatilization, char oxidation, mineral matter transformation, deposition, and corrosion. The experimental data, pressurized oxy-firing system principles, and process mechanisms provided by this work can be used by electric utilities, boiler OEMs, equipment suppliers, design firms, software vendors, consultants and government agencies to assess the use of high temperature and high pressure oxy-combustion in current research and to guide development of new oxy-coal boiler designs.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2021

Characterizing Impacts of Dry Coal Feeding in High Pressure Oxy-Coal Combustion Systems

Reaction Engineering International (REI) has managed a team of experts from the University of Utah, Southeast University (SEU) in Nanjing, China, Electric Power Research Institute (EPRI), Corrosion Management Ltd. (C-M), Praxair, and Brigham Young University (BYU) to investigate dry pulverized coal feeding for pressurized oxy-coal combustion. Dry feed firing systems for entrained flow, pressurized, oxy-coal combustors have not been well developed, although related technologies have been used in the Shell Gasification Process and for pressurized fluid bed combustion. DOE-funded research recently completed at REI and the University of Utah focused on characterizing impacts of high temperatures and pressures in oxy-coal combustion systems. For high pressure combustion, that research used a coal slurry feed into a 17 bar pressurized combustor. As a consequence of that research, it was identified that fuel feeding and firing system flexibility are challenges that require attention. Based on that experience, the approach of using a coal slurry feed system leads to challenges in producing consistent atomization of the slurry, which causes burnout problems, especially at high pressures. In addition, slurry atomization processes may be difficult to scale to sizes appropriate for practical commercial use. Dry pressurized coal burner systems, on the other hand, have the potential to yield efficiency gains, improve flexibility and facilitate applications at larger scales. Experimental work was conducted at the University of Utah Industrial Combustion and Gasification Research Facility as well as the 100 kW pressurized oxy-coal combustor (POC) facility at Brigham Young University. Mechanism development and CFD-based combustion and dense-phase flow modeling were performed at REI. Successful completion of the project objectives has resulted in the following key deliverables: 1) Design and prototype of a pressurized pulverized coal feeding and oxy-firing system 2) Data from a 100kW, pressurized (15 bar) entrained flow reactor with a dry feeding delivery and burner system that describes flame characteristics, radiative heat flux profiles, carbon burnout, along with characteristics of ash aerosols, fouling, and slagging. 3) Validated and transportable models that describe the relevant conditions in pressurized oxy-combustion systems and that can be used for scale-up and optimization. 4) Principles to guide design of high pressure, pilot-scale and full-scale coal oxy-firing systems. 5) Assessment of pressurized oxy-combustion impacts on key parameters relevant to oxy-coal fired utility boilers such as coal devolatilization, char oxidation, mineral matter transformation, deposition, and corrosion. The experimental data, pressurized oxy-firing system principles, and process mechanisms provided by this work can be used by electric utilities, boiler OEMs, equipment suppliers, design firms, software vendors, consultants and government agencies to assess the use of high temperature and high pressure oxy-combustion in current research and to guide development of new oxy-coal boiler designs.

pressurized oxy-coal combustion, sub-micron ash ae↗

DOE OSTI2022

Characterizing Impacts of Dry Coal Feeding in High Pressure Oxy-Coal Combustion Systems

Reaction Engineering International (REI) has managed a team of experts from the University of Utah, Southeast University (SEU) in Nanjing, China, Electric Power Research Institute (EPRI), Corrosion Management Ltd. (C-M), Praxair, and Brigham Young University (BYU) to investigate dry pulverized coal feeding for pressurized oxy-coal combustion. Dry feed firing systems for entrained flow, pressurized, oxy-coal combustors have not been well developed, although related technologies have been used in the Shell Gasification Process and for pressurized fluid bed combustion. DOE-funded research recently completed at REI and the University of Utah focused on characterizing impacts of high temperatures and pressures in oxy-coal combustion systems. For high pressure combustion, that research used a coal slurry feed into a 17 bar pressurized combustor. As a consequence of that research, it was identified that fuel feeding and firing system flexibility are challenges that require attention. Based on that experience, the approach of using a coal slurry feed system leads to challenges in producing consistent atomization of the slurry, which causes burnout problems, especially at high pressures. In addition, slurry atomization processes may be difficult to scale to sizes appropriate for practical commercial use. Dry pressurized coal burner systems, on the other hand, have the potential to yield efficiency gains, improve flexibility and facilitate applications at larger scales. Experimental work was conducted at the University of Utah Industrial Combustion and Gasification Research Facility as well as the 100 kW pressurized oxy-coal combustor (POC) facility at Brigham Young University. Mechanism development and CFD-based combustion and dense-phase flow modeling were performed at REI. Successful completion of the project objectives has resulted in the following key deliverables: 1) Design and prototype of a pressurized pulverized coal feeding and oxy-firing system 2) Data from a 100kW, pressurized (15 bar) entrained flow reactor with a dry feeding delivery and burner system that describes flame characteristics, radiative heat flux profiles, carbon burnout, along with characteristics of ash aerosols, fouling, and slagging. 3) Validated and transportable models that describe the relevant conditions in pressurized oxy-combustion systems and that can be used for scale-up and optimization. 4) Principles to guide design of high pressure, pilot-scale and full-scale coal oxy-firing systems. 5) Assessment of pressurized oxy-combustion impacts on key parameters relevant to oxy-coal fired utility boilers such as coal devolatilization, char oxidation, mineral matter transformation, deposition, and corrosion. The experimental data, pressurized oxy-firing system principles, and process mechanisms provided by this work can be used by electric utilities, boiler OEMs, equipment suppliers, design firms, software vendors, consultants and government agencies to assess the use of high temperature and high pressure oxy-combustion in current research and to guide development of new oxy-coal boiler designs.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2023

Hydrophobic, Thermal Shock-and-Corrosion-Resistant XSBR Latex-Modified Lightweight Class G Cement Composites in Geothermal Well Energy Storage Systems

Energy losses can be significantly reduced if thermally insulating cement is used for energy storage and recovery. The thermal conductivity (TC) of the currently used cement is between 1 and 1.2 W/mK. In this study we assessed the ability of polystyrene (PS)–polybutadiene (PB)–polyacrylic acid (PAA) terpolymer (cross-linked styrene–butadiene rubber, XSBR) latex to improve thermal insulating properties and thermal shock (TS) resistance of class G ordinary Portland cement (OPC) and fly ash cenosphere (FCSs) composites in the temperature range of 100–175 °C. The composites autoclaved at 100 °C were subjected to three cycles, one cycle: 175 °C heat → 25 °C water quenching). In hydrothermal and thermal (TS) environments at elevated temperatures in cement slurries the XSBR latex formed acrylic calcium complexes through acid–base reactions, and the number of such complexes increased at higher temperatures due to the XSBR degradation with formation of additional acrylic groups. As a result, these complexes offered the following five advanced properties to the OPC-based composites: (1) enhanced hydrophobicity; (2) decreased water-fillable porosity; (3) reduced TC for water-saturated composites; (4) minimized loss of compressive strength, Young’s modulus, and compressive fracture toughness after TS; and (5) abated pozzolanic activity of FCSs, which allowed FCSs to persist as thermal insulators under strongly alkaline conditions of cement slurries. Additionally, XSBR-modified slurries possessed improved workability and decreased slurry density due to the air-entraining effect of latex, which resulted in further improvement of thermal insulation performance of the modified composites.

15 GEOTHERMAL ENERGY↗

DOE OSTI2020

Characterization of Oxy-Coal Swirl Injector

The article presents the design and testing of a coal-slurry swirl-pintle injector for high pressure oxy-coal combustion systems. Pressurized oxy-coal combustion-based systems have the potential to improve efficiency by recovering latent heat of the steam in flue gas and achieve 90% CO2 capture. In oxy-coal combustion, coal is burned in the presence of pure oxygen, which results in higher efficiency and less greenhouse gas in the exhaust. With the advancement of pressurized oxy-coal combustor research, there is a need to investigate injector technology suitable for this unique combustion approach. Effective atomization and mixing of coal-slurry and oxidizer pose a challenge for the efficient burning of coal particles. A swirl-pintle type injector was designed and tested to enhance the atomization of the coal-water slurry spray by adding a swirl to the oxygen flow path. Although pintle type injectors are traditionally used in rocket engines, they present a promising approach in clean coal combustion technology due to higher mixing effectiveness and enhanced performance. The mixing behavior of three pintle injectors with different swirl numbers (S = 0, 0.9, and 1.2) was tested using a high-speed shadow sizing technique. Mixture ratios of 30% (by mass) coal-water slurry were studied. The droplet diameter and dispersion characteristics were determined from shadow images of coal-water spray. The jet breakup length, droplet number, total moment ratio (TMR), and Ohnesorge number were then calculated to compare the performance of different injectors. The paper presents an empirical correlation of the TMR with droplet size and spray regimes. For a pintle injector with S = 1.2 swirler, the droplets diameter was found to be in the range of 1 mm to 12 mm. The jet breakup length was also shorter in comparison to S= 0 and 0.9 injectors. A second atomization zone was also observed at 2 and 5 diameters downstream of injector exist at spray edge and jet core respectively

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2023

Coated optical fiber and method of making same

A method is disclosed of making a coated optical fiber. The method may involve drawing a preform through a furnace to create a fiber having a desired diameter and cross sectional shape. The fiber is then drawn through a slurry, wherein the slurry includes elements including at least one of metallic elements, alloy elements or dielectric elements, and the slurry wets an outer surface of the fiber. As the fiber is drawn through the slurry, it is then drawn through a forming die to impart a wet coating having a desired thickness on an outer surface of the fiber. The wet fiber is then drawn through an oven or ovens configured to heat the wet coating sufficiently to produce a consolidated surface coating on the fiber as the fiber exits the oven or ovens.

Messerly, Michael↗

DOE OSTI2024

A Novel Workflow for Coupled Simulation of Hydraulic Stimulation with Simultaneous Injection of Proppant

Enhanced Geothermal Systems (EGS) are located in impermeable host rock. Therefore, to achieve promising circulation, hydraulic stimulation is a key factor. Stimulation involves injecting a combination of fluids and proppant particles into existing fractures under high pressure. The effectiveness of stimulation depends on a variety of different factors, including the pressurization scheme and the optimal choice of carrying fluid and proppant particles to be used. For example, high-density particles can settle out of the injected slurry quickly, whereas lighter particles as well as a dense carrying fluid allow for a long transport into the reservoir. A numerical tool is therefore essential to take all these factors into account and to make robust predictions about the performance of the hydraulic stimulation. We present a novel computational application for coupled numerical simulation of hydraulic stimulation with concurrent injection of proppant in a fractured geothermal reservoir. This application is based on the open-source MOOSE framework that has been enriched with a set of equations to account for the circulation of proppant-laden slurries. It accounts for both the fluid and proppant components of the mixture, as well as particle-driven processes that include gravity settling, particle-particle interactions, and strong density and viscosity contrasts. A particular challenge is the mutual coupling with fracture mechanical processes in a propagating fracture using the FE code Defmod. Aperture and fluid pressure on one side and slurry density and viscosity changes on the other side interact and affect each other. Their basic understanding is therefore essential for the success of the stimulation. We compare our application to common numerical benchmark problems for both slurry flow and hydraulic stimulation.

15 GEOTHERMAL ENERGY↗

DOE OSTI2024

Methods for reducing sediment plume in deepsea nodule mining

A method and apparatus for generating a slurry from the surface of the subsea floor, separating that slurry into multiple slurries, and pumping the desired slurry to the surface.

Halkyard, John↗

DOE OSTI2024

Binder systems and methods for tape casting lithium garnet electrolytes

Slurry compositions, tape casting binder systems and fabrication methods for the fabrication of lithium-garnet electrolyte scaffolds for use in solid state batteries and other devices are provided. Slurry compositions may be optimized mixtures of LLZO powder, a dispersant, a lithium salt, a wetting agent a binder, a plasticizer and at least one solvent. The optimized ceramic slurry compositions may include MgO as a sintering additive to improve density and ionic conductivity of the doped-LLZO sheets and produce a fine-grained microstructure. Sintering protocols for cast slurries of commercially available doped LLZO powders eliminate the requirement of mother-powder coverings or externally applied pressure. An environmentally friendly water-based system using methylcellulose as a binder is also provided producing green tape and final properties comparable to those obtained with organic solvent-based systems.

Jonson, Robert↗

DOE OSTI2026

Tank 11H Low Temperature Aluminum Dissolution and Inhalation Dose Potential Analyses at Savannah River Site – 26018

Currently, there is approximately 34 million gallons of high-level radioactive tank waste in the Tank Farm at the Savannah River Site (SRS). The ultimate goal of operations at the Tank Farm is to remove the high level waste (HLW) from the tanks followed by stabilization of the waste through vitrification of the HLW into glass or grouting the decontaminated waste into saltstone. After bulk removal of the HLW consisting of sludge, saltcake, and supernatant, further efforts are made to reduce the residual waste present in the tank in order to declare preliminary cease waste removal (PCWR) signifying completion of HLW removal. These reduction efforts can include tank washing to remove soluble salts and radioisotopes and dissolution of solids including aluminum. Aluminum in the form of gibbsite and boehmite is relatively insoluble in water. Through addition of aqueous sodium hydroxide, the aluminum can be dissolved at mild temperatures. In order for the waste tank to meet closure mode requirements of the Concentration, Storage, and Transfer Facilities (CSTF), which includes the Tank Farm, Documented Safety Analysis (DSA), a component of the safety basis, the inhalation dose potential (IDP) and the radiolytic hydrogen generation rate of the stored waste must be demonstrated to be lower than their respective designated limits. These parameters are calculated from measured radiochemical analyses of isotopes that emit a high amount of radioactivity including Cs-137, Sr-90, Pu-238, Pu-239, Pu-240, Pu-241, Am-241, and Cm-244. Following the low temperature aluminum dissolution (LTAD) process, Tank 11H slurry samples were pulled from the tank and sent to Savannah River National Laboratory (SRNL) to measure the extent of aluminum dissolution, hydroxide concentration, densities of slurry and supernatant, weight percent solids analyses, and radionuclide activities. The analyses of the composite sample found that approximately 90% of the total aluminum in the slurry was dissolved, indicating successful reduction of the insoluble aluminum in the waste tank. Additionally, the weight percent insoluble solids (slurry basis) measurement of the composite sample was found to be approximately 1%, demonstrating that minimal solids still remain in the tank. Finally, the radiochemical analyses of the composite sample determined that the waste contents of the tank met the IDP and radiolytic hydrogen generation rate requirements of the CSTF DSA. These measurements have shown that the LTAD process in Tank 11H was successful in waste reduction efforts and a positive step towards declaring PCWR and tank closure at SRS.

Dekarske, John [Savannah River National Laboratory↗

DOE OSTI2023

Targeted Particle Fractionation Technologies: Proof of Concept

Most methods of particle-size analysis involve particle fractionation which, is often done by filtration or the use of screens. This paper provides proof of concept testing for new in-pipe particle fractionation technologies that can be used at laboratory to industrial scales. These technologies are extensions of recent advancements in bump arrays as well as testing of new inline angled-to-the-flow slats, and advanced boycott-based Avalanche separation technologies. Experiments were conducted for three targeted particle fractionation technologies to evaluate the in-pipe removal of oversized sands in Newtonian slurries prior to the introduction of bump arrays. The mesofluidic system uses an array of staggered posts as configured in a bump array for Newtonian slurry conditions. The methods and results of these experiments are described in this paper. This information could be applied in most industrial and laboratory systems to rapidly remove oversized particles from a flowing slurry.

slurry, solids removal, particle fractionation, bu↗

DOE OSTI2026

Powdermet CRADA for VELOCITI Voucher (CRADA Final Report)

NLR shall develop a model of an electric thermal energy storage (ETES) system in the System Advisor Model (SAM) framework that uses a salt and particle slurry developed by PowderMet as the thermal energy storage medium. The ETES shall consist of a recuperated sCO 2 Brayton cycle using 2-tank indirect thermal energy storage and an electric heater for heat input. The salt slurry uses chloride salt and operates at a maximum temperature of 500-720°C. The ETES uses dry air cooling. The salt slurry will be modeled as a sensible heat storage medium and as a latent heat storage medium. NLR will use the model to do parametric analysis of the factors affecting the performance (ex., round trip efficiency) of the ETES system. NLR will work with PowderMet to estimate the costs of system components and total system costs, with the levelized cost of electricity (LCOE) as the primary cost metric.

14 SOLAR ENERGY↗

DOE OSTI2022

Screening method for Enzyme-based liquefaction of corn stover pellets at high solids

Liquefaction of high solid loadings of unpretreated corn stover pellets has been demonstrated with rheology of the resulting slurries enabling mixing and movement within biorefinery bioreactors. However, some forms of pelleted stover do not readily liquefy, so it is important to screen out lots of unsuitable pellets before processing is initiated. This work reports a laboratory assay that rapidly assesses whether pellets have the potential for enzyme-based liquefaction at high solids loadings. Twenty-eight pelleted corn stover (harvested at the same time and location) were analyzed using 20 mL enzyme solutions (3 FPU cellulase/ g biomass) at 30 % w/v solids loading. Imaging together with measurement of reducing sugars were performed over 24-hours. Further, some samples formed concentrated slurries of 300 mg/mL (dry basis) in the small-scale assay, which was later confirmed in an agitated bioreactor. Also, the laboratory assay showed potential for optimizing enzyme formulations that could be employed for slurry formation.

Laboratory assay↗

DOE OSTI2021

Through a glass darkly: In-situ x-ray computed tomography imaging of feed melting in continuously fed laboratory-scale glass melter

his study describes the first direct in-situ 3-D observation of a steady-state melting process by imaging a laboratory-scale slurry-fed glass melter in operation by x-ray computed tomography. Features of the reacting glass-feed, the foam layer underneath, and cavities in the glass melt pool are reconstructed in three-dimensional images. A slurry pool formed in a deep central caldera of dense dried feed, which penetrated into the glass melt. Slurry overflow from the caldera led to fast-dried and highly porous feed structure. A thin layer of foam separated the caldera from the melt. Bubbles ?5-15 mm in diameter were seen to grow beneath the reacting feed and move through the melt to escape at the edge. Pore morphology is benchmarked against computed tomography scans of a pellet of reacting simulated waste glass feed, and evolved gas analysis describes the gases generated as a function of temperature. Cooling artifacts are imaged and compared to previous studies of quenched cold caps. Detailed understanding of processes occurring during the conversion process in and below the reacting feed layer is necessary for the development of representative models of the melting process.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Hydration of alumina (Al 2 O 3 ) toward advancing aluminum particles for energy generation applications

Transforming metal particle combustion may require alteration of the metal oxide passivation shell surrounding the metal core. One approach for aluminum (Al) relies on the hydrated form of the metal oxide to incite surface reactions. Here, this study explores the conditions required for hydrating alumina (Al 2 O 3 ) particles and then extends those conditions toward hydration of the Al 2 O 3 passivation layer surrounding an Al core particle. By raising the pH of the water slurry to 11 and controlling temperature and time in slurry (i.e., aging), aluminum hydroxide Al(OH) 3 formation from Al 2 O 3 particles was optimized. The procedure was then extended to Al nanoparticles (nAl). Even though heating and extended aging time in slurry proved advantageous for Al 2 O 3 particles, these conditions were discarded for nAl particles because they favored formation of AlOOH, a less desirable hydrate. Through microscopy, spectroscopy, X-ray diffraction, and thermal analyses, results indicate that for a pH range of 11.26–11.56, the original Al 2 O 3 shell on Al particles transformed into Al(OH) 3 . Results indicate a feasible path forward towards producing new shell chemistries that may result in more directed energy from metal particle combustion.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Enabling aqueous processing for LiNi 0.80 Co 0.15 Al 0.05 O 2 (NCA)-based lithium-ion battery cathodes using polyacrylic acid

Replacing N-methyl-2-pyrrolidone (NMP) with water in the production of lithium-ion battery cathodes is critical to realizing process cost savings and improved worker safety. LiNi 0.80 Co 0.15 Al 0.05 O 2 (NCA) is a poor fit for aqueous processing due to destructive Al current collector corrosion resulting from highly basic slurries and detrimental surface reconstruction reactions that occur in water. In this study, polyacrylic acid (PAA, MW = 450,000 g·mol -1 ) is examined as a corrosion-mitigating and surface-stabilizing agent. Adding PAA to an aqueous NCA slurry can provide a stable pH (4.0–8.5) for at least 4 h, since the carboxyl groups from PAA dissociate and increase the proton concentration in the slurry. Further, these groups can also adsorb to the surface of NCA particles and provide electrostatic stability from active material particle agglomeration, as revealed by zeta potential measurements. Minor cracking does occur at the electrode surface; this cracking likely caused poorer adhesion to the Al current collector in the aqueous-processed film when compared to the NMP-processed baseline. Electrochemically, the leached Li does cause a lower initial capacity for the aqueous-processed cathode, though the capacity retention of the aqueous-processed cathode is better than the baseline. The cracks in the coating led to a rise in charge transfer resistance that hindered rate capability above 1C.

25 ENERGY STORAGE↗