Search NASA⌕ Search

SEARCH · Search NASA

Results for “STALLING - PREVENTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

An experimental and analytical investigation of stall effects on flap-lag stability in forward flight

Experiments have been performed with a 1.62 m diameter hingeless rotor in a wind tunnel to investigate flap-lag stability of isolated rotors in forward flight. The three-bladed rotor model closely approaches the simple theoretical concept of a hingeless rotor as a set of rigid, articulated flap-lag blades with offset and spring restrained flap and lag hinges. Lag regressing mode stability data was obtained for advance ratios as high as 0.55 for various combinations of collective pitch and shaft angle. The prediction includes quasi-steady stall effects on rotor trim and Floquet stability analyses. Correlation between data and prediction is presented and is compared with that of an earlier study based on a linear theory without stall effects. While the results with stall effects show marked differences from the linear theory results, the stall theory still falls short of adequate agreement with the experimental data.

Nagabhushanam, J.↗
NASA NTRS1993

Prediction of active control of subsonic centrifugal compressor rotating stall

A mathematical model is developed to predict the suppression of rotating stall in a centrifugal compressor with a vaned diffuser. This model is based on the employment of a control vortical waveform generated upstream of the impeller inlet to damp weak potential disturbances that are the early stages of rotating stall. The control system is analyzed by matching the perturbation pressure in the compressor inlet and exit flow fields with a model for the unsteady behavior of the compressor. The model was effective at predicting the stalling behavior of the Purdue Low Speed Centrifugal Compressor for two distinctly different stall patterns. Predictions made for the effect of a controlled inlet vorticity wave on the stability of the compressor show that for minimum control wave magnitudes, on the order of the total inlet disturbance magnitude, significant damping of the instability can be achieved. For control waves of sufficient amplitude, the control phase angle appears to be the most important factor in maintaining a stable condition in the compressor.

Lawless, Patrick B.↗
NASA NTRS1939

Observations in Flight of the Region of Stalled Flow over the Blades of an Autogiro Rotor

The flow over the inner halves of the rotor blades on a Kellet YG-1B autogiro was investigated in flight by making camera records of the motion of silk streamers attached to the upper surfaces of the blades. These records were analyzed to determine the boundaries of the region within which the flow over the blade sections was stalled for various tip-speed ratios. For the sake of comparison, corresponding theoretical boundaries were obtained. Both the size of the stalled area and its rate of growth with increasing tip-speed ratio were found to be larger than the theory predicted, although experiment agreed with theory with regard to shape and general location of the stalled area. The stalled region may be an important factor in both the rotor lift-drag ratio and the blade flapping motion at the higher tip-speed ratios. The method of study used in this paper should be useful in further studies of the problem, including the reduction of the size of the region.

Bailey, F J , Jr↗
NASA NTRS1940

Notes on the stalling of vertical tail surfaces and on fin design

A discussion is given of the important aspects of the stalling of vertical tail surfaces. The type of instability encountered is described and the possibilities of inadvertent occurrence are noted. The influence of directional flight tests on the behavior of a airplane when the tail stall takes place is discussed. In this connection, flight tests of a twin-engine airplane in which the vertical fin area was increased are cited. The reasons for inadequate directional stability in certain modern designs are accounted for and the properties and applications of dorsal fins are discussed. In addition, the chief factors regulating the requirements for conventional area are given, in which connection simplified criterion for directional stability is presented. It may be concluded that the stalling of vertical tail surfaces is not in itself a dangerous condition. Provided sufficient directional stability exists at large angles of sideslip, the tail stall may occur with modern airplanes, as with those of the past, without the knowledge or concern to the pilot.

Thompson, F L↗
NASA NTRS1954

Multiple over-all performance and rotating-stall characteristics of a 15-stage experimental axial-flow compressor at an intermediate speed

The 15-stage experimental axial-flow compressor was investigated at 78.5 percent of design speed, which falls in the region of the surge-limit line discontinuity. In this region indications of multiple characteristic curves of compressor operation had been found. On the basis of previous stage-matching analyses, these multiple performance characteristics appear to be the result of multiple-valued stage performance characteristics. At this speed of 78.5 percent, at least six separate characteristic performance curves were found, associated with five different numbers of rotating stall configurations, from zero to four stall zones. It was difficult in many cases to repeat a given performance curve by approaching the test speed in a similar manner, and many of the curves were not stable, the no-stall curve being the only definitely repeatable one. In some cases a jump from one curve to another took place at the surge point, while in others the change occurred within the usual limits of a conventional performance curve and without any sudden obvious changes in observed data. In general, as the number of zones in the rotating-stall pattern decreased, the maximum weight flow, maximum efficiency, and maximum pressure ratio of the resultant curves were increased. It appears, therefore, that multiple performance characteristics at the given speed are encountered in the region of the discontinuity of the surge line.

Lucas, James G↗
NASA NTRS1956

Experimental Investigation of an Overriding Control to Effect Recovery from Surge and Stall in a Turbojet Engine

The override was designed to automatically recover the engine from stall and surge by reducing fuel flow and then increasing fuel flow in a manner to avoid repeated stalls and surges and successfully complete the acceleration. One of two parameters was used to operate the override, tailpipe temperature, or the derivative of compressor-discharge pressure. The override operating with tailpipe temperature recovered the engine from stall and surge. Operating on compressor-discharge-pressure derivative, the override recovered the engine from surge, but failed when stall was encountered.

Stiglic, Paul M↗
NASA NTRS1947

Boundary-layer and stalling characteristics of two symmetrical NACA low-drag airfoil sections

Two symmetrical airfoils, an NACA 633-018 and an NACA 631-012, were investigated for the purpose of determining their stalling and boundary-layer characteristics with a view toward the eventual application of this information to the problem of boundary-layer control. Force measurements, pressure distributions, tuft studies, and boundary-layer-profile measurements were made at a value of 5,800,000 Reynolds number. It was found that the 18-percent-thick airfoil stalled progressively from the trailing edge because of separation of the turbulent boundary layer. In contrast, the12-percent-thick airfoil stalled abruptly from a separation of flow near the leading edge before the turbulent boundary layer became subject to separation. From this it was concluded that if high values of lift are to be obtained with thin, high-critical-speed sections by means of boundary-layer control, the work must be directed toward delaying the separation of flow near the leading edge. It was found that the presence of a nose flap on the 12-percent-thick section caused the airfoil to stall in a manner similar to that of the 18-percent-thick section.

Mccullough, George B↗
NASA NTRS1994

Control of unsteady separated flow associated with the dynamic stall of airfoils

A unique active flow-control device is proposed for the control of unsteady separated flow associated with the dynamic stall of airfoils. The device is an adaptive-geometry leading-edge which will allow controlled, dynamic modification of the leading-edge profile of an airfoil while the airfoil is executing an angle-of-attack pitch-up maneuver. A carbon-fiber composite skin has been bench tested, and a wind tunnel model is under construction. A baseline parameter study of compressible dynamic stall was performed for flow over an NACA 0012 airfoil. Parameters included Mach number, pitch rate, pitch history, and boundary layer tripping. Dynamic stall data were recorded via point-diffraction interferometry and the interferograms were analyzed with in-house developed image processing software. A new high-speed phase-locked photographic image recording system was developed for real-time documentation of dynamic stall.

Wilder, M. C.↗
NASA NTRS1994

Dynamic-stall and structural-modeling effects on helicopter blade stability with experimental correlation

The effects of blade and root-flexure elasticity and dynamic stall on the stability of hingeless rotor blades are investigated. The dynamic stall description is based on the ONERA models of lift, drag, and pitching moment. The structural analysis is based on three blade models that range from a rigid flap-lag model to two elastic flap-lag-torsion models, which differ in representing root-flexure elasticity. The predictions are correlated with the measured lag damping of an experimental isolated three-blade rotor; the correlation covers rotor operations from near-zero-thrust conditions in hover to highly stalled, high-thrust conditions in foward flight. That correlation shows sensitivity of lag-damping predictions to structural refinements in blade and root-flexure modeling. Moreover, this sensitivity increases with increasing control pitch angle and advance ratio. For high-advance-ratio and high-thrust conditions, inclusion of dynamic stall generally improves the correlation.

Barwey, D.↗
NASA NTRS1996

A Survey of Reynolds Number and Wing Geometry Effects on Lift Characteristics in the Low Speed Stall Region

This paper presents a survey of the effects of Reynolds number on the low- speed lift characteristics of wings encountering separated flows at their leading and side edges, with emphasis on the region near the stall. The influence of leading-edge profile and Reynolds number on the stall characteristics of two- dimensional airfoils are reviewed first to provide a basis for evaluating three- dimensional effects associated with various wing planforms. This is followed by examples of the effects of Reynolds number and geometry on the lift characteristics near the stall for a series of three-dimensional wings typical of those suitable for high-speed aircraft and missiles. Included are examples of the effects of wing geometry on the onset and spanwise progression of turbulent reseparation near the leading edge and illustrations of the degree to which simplified theoretical approaches can be useful in defining the influence of the various geometric parameters. Also illustrated is the manner in which the Reynolds number and wing geometry parameters influence whether the turbulent reseparation near the leading edge results in a sudden loss of lift, as in the two-dimensional case, or the formation of a leading-edge vortex with Rs increase in lift followed by a gentle stall as in the highly swept wing case. Particular emphasis is placed on the strong influence of 'induced camber' on the development of turbulent reseparation. R is believed that the examples selected for this report may be useful in evaluating viscous flow solutions by the new computational methods based on the Navier-Stokes equations as well as defining fruitful research areas for the high-Reynolds-number wind tunnels.

Polhamus, Edward C.↗
NASA NTRS1999

Application of CFD to Explain Anomalous Stall Behavior of the SSME Flowmeter

Anomalous behavior manifested in the apparent SSME fuel flowmeter constant which relates the rotor speed to the engine flowrate has been shown to be the result of wakes of the upstream hexagonal web flow straightener periodically stalling the rotor blades, thereby changing the lift on the blades and the rotation speed of the rotor. Moreover, an unsteady, two-dimensional computational fluid dynamics model of the flowmeter has shown this wake-induced stall disappearing as the straightener-rotor distance is doubled, in accord with the existing SSME flowmeter database for the previous "egg crate" flowmeter. These observations have led to a new flowmeter design which has been shown in three-dimensional CFD computations (consistent with both the previous two-dimensional analyses and with existing correlations for airfoil stall) to be much less susceptible to stalling instabilities.

Ascoli, E.↗
NASA NTRS2000

Evaluation of Airfoil Dynamic Stall Characteristics for Maneuverability

In severe maneuvers, out of necessity for a military aircraft or inadvertently for a civil aircraft, a helicopter airfoil will stall in a dynamic manner and provide lift beyond what would be calculated based on static airfoil tests. The augmented lift that occurs in dynamic stall is related to a vortex that is shed near the leading edge of the airfoil. However, directly related to the augmented lift that results from the dynamic stall vortex are significant penalties in pitching moment and drag. An understanding of the relationship between the augmented lift in dynamic stall and the associated moment and drag penalties is the purpose of this paper. This relationship is characterized using data obtained in two-dimensional wind tunnel tests and related to the problem of helicopter maneuverability.

Bousman, William G.↗
NASA NTRS1994

An Assessment of the Effect of Compressibility on Dynamic Stall

Compressibility plays a significant role in the development of separation on airfoils experiencing unsteady motion, even at moderately compressible free-stream flow velocities. This effect can result in completely changed stall characteristics compared to those observed at incompressible speed, and can dramatically affect techniques used to control separation. There has been a significant effort in recent years directed toward better understanding; of this process, and its impact on possible techniques for control of separation in this complex environment. A review of existing research in this area will be presented, with emphasis on the physical mechanisms that play such an important role in the development of separation on airfoils. The increasing impact of compressibility on the stall process will be discussed as a function of free-stream Mach number, and an analysis of the changing flow physics will be presented. Examples of the effect of compressibility on dynamic stall will be selected from both recent and historical efforts by members of the aerospace community, as well as from the ongoing research program of the present authors. This will include a presentation of a sample of high speed filming of compressible dynamic stall which has recently been created using real-time interferometry.

Carr, Lawrence W.↗
NASA NTRS1998

The Control of Compressible Dynamic Stall Using Adaptive Airfoils

Ongoing research has shown that compressible dynamic stall can be caused by vastly different mechanisms even for small changes in flow conditions. For example, at low Mach numbers (M less than 0.3) and Reynolds numbers (less than 1 x 10(exp 6)), the bursting of the laminar separation bubble induces dynamic stall. At a slightly higher Mach number (M = 0.45) and around the same Reynolds number, shock induced separation can cause dynamic stall. Also, the mechanism changes from that of laminar separation bubble bursting to that due to excessive adverse pressure gradient, with increase of Reynolds number. Complex interactions occurring between the local supersonic flow and the bubble lead to another possible mechanism of dynamic stall. Since all these mechanisms may be encountered by a rotor-blade during a single cycle, there is a strong need to devise a reliable flow control method for use under such dramatically varying conditions. Whereas it is a Ali 'Beneficent challenge, identification of the fact that these mechanisms are all in some way related to the airfoil leading edge adverse pressure gradient, has resulted in an effective method of flow control to be described.

Chandasekhara, M. S.↗
NASA NTRS1946

Longitudinal Stability and Stalling Characteristics of a 1/8.33-Scale Model of the Republic XF-12 Airplane

The XF-12 airplane is a high performance, photo-reconnaissance aircraft designed by the Republic Aviation Corporation for Army Air Forces. A series of tests of a 1/8.33-scale powered model was conducted in the Langley 9-foot pressure tunnel to obtain information relative to the aerodynamic design of the airplane. This report presents the results of tests to determine the static longitudinal stability and stalling characteristics of the model. From this investigation it was indicated that the airplane will possess a positive static margin for all probable flight conditions. The stalling characteristics are considered satisfactory in that the stall initiates near the root section and progresses toward the tips. Early root section stalling occurs, with the flaps retracted and may cause undesirable tail buffeting and erratic elevator control in the normal flight range. From considerations of sinking speed landing flap deflections of 40 degrees may be preferable to 55 degrees of 65 degrees.

Pepper, Edward↗
NASA NTRS2005

Post-Stall Aerodynamic Modeling and Gain-Scheduled Control Design

A multidisciplinary research e.ort that combines aerodynamic modeling and gain-scheduled control design for aircraft flight at post-stall conditions is described. The aerodynamic modeling uses a decambering approach for rapid prediction of post-stall aerodynamic characteristics of multiple-wing con.gurations using known section data. The approach is successful in bringing to light multiple solutions at post-stall angles of attack right during the iteration process. The predictions agree fairly well with experimental results from wind tunnel tests. The control research was focused on actuator saturation and .ight transition between low and high angles of attack regions for near- and post-stall aircraft using advanced LPV control techniques. The new control approaches maintain adequate control capability to handle high angle of attack aircraft control with stability and performance guarantee.

Wu, Fen↗
NASA NTRS2006

Signature of Temporary Burning Front Stalling from a Non-Photospheric Radius Expansion Double-Peaked Burst

Non-photospheric-radius-expansion(non-PRE) double-peaked bursts may be explained in terms of spreading (and temporary stalling) of thermonuclear flames on the neutron star surface, as we argued in a previous study of a burst assuming polar ignition. Here we analyze Rossi X-ray Timing Explorer (RXTE) Proportional Counter Array (PCA) data of such a burst (but with a considerably different intensity profile from the previous one) from the low mass X-ray binary (LMXB) system 4U 1636-536, and show that this model can qualitatively explain the observed burst profile and spectral evolution, if we assume an off-polar, but high-latitude ignition, and burning front stalling at a higher latitude compared to that for the previous burst. The off-polar ignition can account for the millisecond period brightness oscillations detected from this burst. This is the first time oscillations have been seen from such a burst. Our model can qualitatively explain the oscillation amplitude measured during the first (weaker) peak, and the absence of oscillations during the second peak. The higher latitude front stalling facilitates the first clear detection of a signature of this stalling, which is the primary result of this work, and may be useful for understanding thermonuclear flame spreading on neutron stars.

Bhattacharyya, Sudip↗
NASA NTRS2014

Combustion-Powered Actuation for Dynamic Stall Suppression - Simulations and Low-Mach Experiments

An investigation on dynamic-stall suppression capabilities of combustion-powered actuation (COMPACT) applied to a tabbed VR-12 airfoil is presented. In the first section, results from computational fluid dynamics (CFD) simulations carried out at Mach numbers from 0.3 to 0.5 are presented. Several geometric parameters are varied including the slot chordwise location and angle. Actuation pulse amplitude, frequency, and timing are also varied. The simulations suggest that cycle-averaged lift increases of approximately 4% and 8% with respect to the baseline airfoil are possible at Mach numbers of 0.4 and 0.3 for deep and near-deep dynamic-stall conditions. In the second section, static-stall results from low-speed wind-tunnel experiments are presented. Low-speed experiments and high-speed CFD suggest that slots oriented tangential to the airfoil surface produce stronger benefits than slots oriented normal to the chordline. Low-speed experiments confirm that chordwise slot locations suitable for Mach 0.3-0.4 stall suppression (based on CFD) will also be effective at lower Mach numbers.

Matalanis, Claude G.↗