Search NASA⌕ Search

SEARCH · Search NASA

Results for “SUBLIMATION HEAT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Personal Cooling for Extra-Vehicular Activities on Mars

Extra-vehicular activities (EVA) on Mars will require suits with sophisticated thermal control systems so that astronauts can work comfortably for extended periods of time. Any use of consumables such as water that cannot be easily replaced should be of particular concern. In this aspect the EVA suits for Mars environment need to be different from the current Space Shuttle Extra Vehicular Mobility Units (EMU) that depend on water sublimation into space for removing heat from suits. Moreover, Mars environment is quite different from what a typical EMU may be exposed to. These variations call for careful analysis and innovative engineering for design and fabrication of an appropriate thermal control system. This paper presents a thermal analysis of astronaut suits for EVA with medium metabolic intensity under a typical hot and a nominal cold environment on Mars. The paper also describes possible options that would allow conservation of water with low usage of electrical power. The paper then presents the conceptual design of a portable cooling unit for one such solution.

Pu, Zhengxiang↗
NASA NTRS2004

Freeze Tolerant Radiator for an Advanced EMU

During an Extravehicular Activity (EVA), the astronaut s metabolic heat and the heat produced by the Portable Life Support Unit (PLSS) must be rejected. This heat load is currently rejected by a sublimator, which vents up to eight pounds of water each EVA. However, for advanced space missions of the future, water venting to space needs to be minimized because resupply impacts from earth will be prohibitive. If this heat load could be radiated to space from the PLSS, which has enough surface area to radiate most of the heat, the amount of water now vented could be greatly reduced. Unfortunately, a radiator rejects heat at a relatively constant rate, but the astronauts generate a variable heat load depending on how hard they are working. Without a way to vary the heat removal rate, the astronaut would experience cold discomfort or even frostbite. A proven method allowing a radiator to be turned-down is to sequentially allow tubes that carry the heat transfer fluid to the radiator to freeze. A drawback of current freezable radiators using this method is that they are far to heavy for use on a PLSS, because they use heavy construction to prevent the tubes from bursting as they freeze and thaw. This creates the need for a large radiator to reject most of the heat but with a lightweight tube that doesn t burst as it freezes and thaws. The new freezable radiator for the Extravehicular Mobility Unit (EMU) has features to accommodate the expansion of the radiator fluid when it freezes, and still have the high tube to fin conductance needed to minimize the number and weight of the tubes. Radiator fluid candidates are water and a propylene glycol-water mixture. This design maintains all materials within their elastic limits so that large volume changes can be achieved without breaking the tube. This concept couples this elastic expansion with an extremely lightweight, extremely high conductivity carbon fiber fin that can carry the heat needed to thaw a frozen tube. By using most of the exposed surface area of the PLSS as a radiator, the system can reject about 75% of the highest heat load, and reduce the loss of water through sublimation by a factor of four. The proposed radiator and a small water tank can be no heavier than the current system.

Copeland, Robert J.↗
NASA NTRS2005

Space Suit Radiator Performance in Lunar and Mars Environments

During an ExtraVehicular Activity (EVA), both the heat generated by the astronaut's metabolism and that produced by the Portable Life Support System (PLSS) must be rejected to space. The heat sources include the heat of adsorption of metabolic CO2, the heat of condensation of water, the heat removed from the body by the liquid cooling garment and the load from the electrical components. Although the sublimator hardware to reject this load weighs only 1.58 kg (3.48 lbm), an additional 3.6 kg (8 lbm) of water are loaded into the unit, most of which is sublimated and lost to thus become the single largest expendable during an eight hour EVA. We can significantly reduce the amount of expendable water consumed in the sublimator by using a radiator to reject heat from the Astronaut during an EVA. Last year we reported on the design and initial operational assessment tests of our novel radiator designated the Radiator And Freeze Tolerant heat eXchanger (RAFT-X). Herein, we report on tests conducted in the NASA Johnson Space Center Chamber E Thermal Vacuum Test Facility. Up to 260 W (900 Btu/h) of heat were rejected in Lunar and Mars environments with temperatures as cold as -170 C (- 275 F). Further, the RAFT-X endured several freeze / thaw cycles and in fact, the heat exchanger was completely frozen three times without any apparent damage to the unit.

Nabity, James↗
NASA NTRS1993

Metal hydride heat pump engineering demonstration and evaluation model

Future generations of portable life support systems (PLSS's) for space suites (extravehicular mobility units or EMU's) may require regenerable nonventing thermal sinks (RNTS's). For purposes of mobility, a PLSS must be as light and compact as possible. Previous venting PLSS's have employed water sublimators to reject metabolic and equipment heat from EMU's. It is desirable for long-duration future space missions to minimize the use of water and other consumables that need to be periodically resupplied. The emission of water vapor also interferes with some types of instrumentation that might be used in future space exploration. The test article is a type of RNTS based on a metal hydride heat pump (MHHP). The task of reservicing EMU's after use must be made less demanding in terms of time, procedures, and equipment. The capability for quick turnaround post-EVA servicing (30 minutes) is a challenging requirement for many of the RNTS options. The MHHP is a very simple option that can be regenerated in the airlock within the 30 minute limit by the application of a heating source and a cooling sink. In addition, advanced PLSS's must provide a greater degree of automatic control, relieving astronauts of the need to manually adjust temperatures in their liquid cooled ventilation garments (LCVG's). The MHHP includes automatic coolant controls with the ability to follow thermal load swings from minimum to maximum in seconds. The MHHP includes a coolant loop subsystem with pump and controls, regeneration equipment for post-EVA servicing, and a PC-based data acquisition and control system (DACS).

Lynch, Franklin E.↗
NASA NTRS2000

Thickness of tropical ice and photosynthesis on a snowball Earth

On a completely ice-covered "snowball" Earth the thickness of ice in the tropical regions would be limited by the sunlight penetrating into the ice cover and by the latent heat flux generated by freezing at the ice bottom--the freezing rate would balance the sublimation rate from the top of the ice cover. Heat transfer models of the perennially ice-covered Antarctic dry valley lakes applied to the snowball Earth indicate that the tropical ice cover would have a thickness of 10 m or less with a corresponding transmissivity of > 0.1%. This light level is adequate for photosynthesis and could explain the survival of the eukaryotic algae.

NASA Center ARC↗
NASA NTRS1954

Experimental Determination of Thermal Conductivity of Low-Density Ice

The thermal conductivity of low-density ice has been computed from data obtained in an experimental investigation of the heat transfer and mass transfer by sublimation for an iced surface on a flat plate in a high-velocity tangential air stream. The results are compared with data from several sources on the thermal conductivity of packed snow and solid glaze ice. The results show good agreement with the equations for the thermal conductivity of packed snow as a function of snow density. The agreement of the curves for packed snow near the solid ice regime with the values of thermal conductivity, of ice indicates that the curves are applicable over the entire-ice-density range.

Coles, Willard D.↗
NASA NTRS1985

Numerical simulation of comet nuclei. I - Water-ice comets

A one-dimensional numerical model of pure water-ice cometary nuclei is presented, and the influence of the nuclear interior as a heat reservoir on the behavior of the nuclear surface is examined. It is shown that a number of effects, including the thermal inertia due to heat stored in the core and the release of latent heat, which goes entirely into heating the adjacent layers or into sublimation on passing through a phase transition from amorphous to crystalline ice, can help to explain such characteristics as the asymmetrical lightcurve of Comet Halley. Results are given for the cases of Comet Schwassmann-Wachmann 1 and Comet Encke. Consideration is also given to the insulating effect of an evolving dust mantle. The role of this mantle in determining the surface temperature of the ice core is studied as a function of the mass fraction of the dust in the ice-dust mixture and the thermal conductivity of the nucleus. The loose-lattice model of Mendis and Brin (1977) indicates that both high dust to ice ratios and high-core conductivities inhibit mantle blowoff.

Herman, G.↗
NASA NTRS1973

Long life performance predictions of SiGe MHW-RTG.

Recent experimental investigations at JPL, Resalab and GGA are incorporated into an analytical model which predicts generator performance over long time periods. The important aging mechanisms considered are degradation in foil insulation conductivity due to reactions with Si sublimed from the hot shoe and SiO2 from the astroquartz layers; changes in hot shoe dimensions due to Si sublimation; changes in leg dimensions due to SiGe sublimation; baffling factors which are applied to the legs to correct the free sublimation model for various effects such as geometry, reactions with the astroquartz wrapping, and hot shoe Si generation; new bulk property changes due to dopant precipitation; and changes in radiation heat exchange due to gap streaming as leg material sublimes.

Caputo, R. S.↗
NASA NTRS1972

A Numerical Analysis of the Transient Response of an Ablation System Including Effects of Thermal Nonequilibrium, Mass Transfer and Chemical Kinetics

The differential equations governing the transient response of a one-dimensional ablative thermal protection system undergoing stagnation ablation are derived. These equations are for thermal nonequilibrium effects between the pyrolysis gases and the char layer and kinetically controlled chemical reactions and mass transfer between the pyrolysis gases and the char layer. The boundary conditions are written for the particular case of stagnation heating with surface removal by oxidation or sublimation and pyrolysis of the uncharred layer occurring in a plane. The governing equations and boundary conditions are solved numerically using the modified implicit method (Crank-Nicolson method). Numerical results are compared with exact solutions for a number of simplified cases. The comparison is favorable in each instance.

Clark, R. K.↗
NASA NTRS1981

Pluto's atmospheric bulk near perihelion

The detection of CH4 frost on Pluto's surface implies a significant atmosphere for Pluto. Although Pluto's mass is small, about 7% of Triton's mass, the rapid escape ('blowoff') of gaseous CH4 can be prevented by the presence of a heavy gas mixed with the CH4. The resulting slow escape ('Jeans escape') of CH4 can be accommodated by sublimation of the surface CH4 frost so that an atmosphere exists in the steady state. A heavier gas must exist, otherwise the CH4 frost would have sublimated away long ago because of solar heat and rapid blowoff of gaseous CH4. Pluto is currently near perihelion where the CH4 component of the atmosphere may be 500 times denser than at apehelion. Significant seasonal changes in the atmospheric bulk are therefore possible.

Trafton, L.↗
NASA NTRS1987

Effect of rib angle on local heat/mass transfer distribution in a two-pass rib-roughened channel

The naphthalene sublimation technique is used to investigate the heat transfer characteristics of turbulent air flow in a two-pass channel. A test section that resembles the internal cooling passages of gas turbine airfoils is employed. The local Sherwood numbers on the ribbed walls were found to be 1.5-6.5 times those for a fully developed flow in a smooth square duct. Depending on the rib angle-of-attack and the Reynolds number, the average ribbed-wall Sherwood numbers were 2.5-3.5 times higher than the fully developed values.

Chandra, P. R.↗
NASA NTRS2013

System of extraction of volatiles from soil using microwave processes

A device for the extraction and collection of volatiles from soil or planetary regolith. The device utilizes core drilled holes to gain access to underlying volatiles below the surface. Microwave energy beamed into the holes penetrates through the soil or regolith to heat it, and thereby produces vapor by sublimation. The device confines and transports volatiles to a cold trap for collection.

Ethridge, Edwin C.↗
NASA NTRS2014

Spacesuit Water Membrane Evaporator; An Enhanced Evaporative Cooling Systems for the Advanced Extravehicular Mobility Unit Portable Life Support System

Spacesuit Water Membrane Evaporator - Baseline heat rejection technology for the Portable Life Support System of the Advanced EMU center dot Replaces sublimator in the current EMU center dot Contamination insensitive center dot Can work with Lithium Chloride Absorber Radiator in Spacesuit Evaporator Absorber Radiator (SEAR) to reject heat and reuse evaporated water The Spacesuit Water Membrane Evaporator (SWME) is being developed to replace the sublimator for future generation spacesuits. Water in LCVG absorbs body heat while circulating center dot Warm water pumped through SWME center dot SWME evaporates water vapor, while maintaining liquid water - Cools water center dot Cooled water is then recirculated through LCVG. center dot LCVG water lost due to evaporation (cooling) is replaced from feedwater The Independent TCV Manifold reduces design complexity and manufacturing difficulty of the SWME End Cap. center dot The offset motor for the new BPV reduces the volume profile of the SWME by laying the motor flat on the End Cap alongside the TCV.

Bue, Grant C.↗
NASA NTRSDate not supplied

An Experimental Study on Low Pressure Frost Formation for Lunar Polar Water Capture

In-situ resource utilization (ISRU) is a vital component of NASA’s mission to the Moon and beyond, as the extraction of resources from the environment can reduce payload weight and the frequency of resupply missions. Since the discovery of water in the regolith of the permanently shadowed regions (PSR) of the Moon, its extraction and transport has become an area of increasing interest for NASA. One proposed method is heating icy regolith to free the water before de-sublimating and transporting it as ice in a tanker. However, little is known regarding the dynamics of frost growth at low pressures, and an understanding of the heat transfer process is required to properly size the heat exchanger for the tanker. To investigate this phenomenon, a cold plate was placed in a vacuum chamber with water vapor directed at its surface. The chamber pressure (300 and 500 Pa) and cold plate temperature (–18 to –5 °C) were kept below the triple point and varied throughout the experiment to examine their impact on frost layer heat transfer. As water flowed into the chamber and deposited on the cold plate surface, the heat flux and temperature were measured along with the frost layer thickness and/or mass. Density calculated at the conclusion of each test suggests the frost layer is denser than that of frost grown at atmospheric pressure. The results demonstrate unexpected density and heat transfer characteristics and require development of a new model of frost growth for lunar conditions

Lunar polar↗
NASA NTRS1972

A study of graphite ablation in combined convective and radiative heating.

Comparison of graphite ablation experiment results in the diffusion-controlled oxidation and sublimation regimes with results of an equilibrium chemistry, film coefficient ablation analysis. Mass transfer and energy transfer effects are considered. Tests were conducted in an arcjet facility at convective heating rates of 600 to 800 W/sq cm, radiative heating rates up to 2900 W/sq cm, with test specimen surface pressures of 0.06, 0.1, and 0.3 atm in an air stream. The experimental and analytical mass loss and surface temperature results agreed well when the carbon vapor thermodynamic properties from the JANAF tables are used in the analysis.

Wakefield, R. M.↗
NASA NTRS1985

The Martian climate: Energy balance models with CO2/H2O atmospheres

Coupled equations are developed for mass and heat transport in a seasonal Mars model with condensation and sublimation of CO2 at the polar caps. Topics covered include physical considerations of planetary as mass and energy balance; effects of phase changes at the surface on mass and heat flux; atmospheric transport and governing equations; and numerical analysis.

Hoffert, M. I.↗
NASA NTRS2004

Membrane-Based Water Evaporator for a Space Suit

A membrane-based water evaporator has been developed that is intended to serve as a heat-rejection device for a space suit. This evaporator would replace the current sublimator that is sensitive to contamination of its feedwater. The design of the membrane-based evaporator takes advantage of recent advances in hydrophobic micropore membranes to provide robust heat rejection with much less sensitivity to contamination. The low contamination sensitivity allows use of the heat transport loop as feedwater, eliminating the need for the separate feedwater system used for the sublimator. A cross section of the evaporator is shown in the accompanying figure. The space-suit cooling loop water flows into a distribution plenum, through a narrow annulus lined on both sides with a hydrophobic membrane, into an exit plenum, and returns to the space suit. Two perforated metal tubes encase the membranes and provide structural strength. Evaporation at the membrane inner surface dissipates the waste heat from the space suit. The water vapor passes through the membrane, into a steam duct and is vented to the vacuum environment through a back-pressure valve. The back-pressure setting can be adjusted to regulate the heat-rejection rate and the water outlet temperature.

Ungar, Eugene K.↗
NASA NTRS2007

Space Suit Radiator Performance in Lunar and Mars Environments

During an ExtraVehicular Activity (EVA), both the heat generated by the astronaut's metabolism and that produced by the Portable Life Support System (PLSS) must be rejected to space. The heat sources include the heat of adsorption of metabolic CO2, the heat of condensation of water, the heat removed from the body by the liquid cooling garment and the load from the electrical components. Although the sublimator hardware to reject this load weighs only 3.48 lbs, an additional eight pounds of water are loaded into the unit of which about six to eight are sublimated and lost; this is the single largest expendable during an eight-hour EVA. Using a radiator to reject heat from the Astronaut during an EVA, we can significantly reduce the amount of expendable water consumed by the sublimator. Last year we reported on the design and initial operational assessment tests of our novel radiator designated the Radiator And Freeze Tolerant heat eXchanger (RAFT-X). Herein, we report on tests conducted in the NASA Johnson Space Center Chamber E Thermal Vacuum Test Facility. Up to 800 Btu/h of heat were rejected in lunar and Mars environments with temperatures as cold as -150 F. Tilting the radiator did not cause an observable loss in performance. The RAFT-X endured freeze / thaw cycles and in fact, the heat exchanger was completely frozen three times without any apparent damage to the unit. We were also able to operate the heat exchanger in a partially frozen configuration to throttle the heat rejection rate from 530 Btu/h at low water flow rate down to 300 Btu/h. Finally, the deliberate loss of a single loop heat pipe only degraded the heat rejection performance by about 2 to 5%.

Nabity, James↗